Search

We report experimental results of a frequency shifted digital holography setup for spatially resolved vibrometry. A spatially homogeneous artificial phase modulation is used as a reference to correct for speckle noise. Furthermore, when superimposed upon the object vibration with slightly different frequency, the resulting beat can be evaluated. The beat frequency is invariant under relative motion between the object and interferometer, providing robustness in presence of parasitic low-frequency vibrations. In addition, the ’working point’ is raised out of the noise floor, providing the opportunity to enhance the sensitivity at small vibration displacements. The method is demonstrated by measurements on a vibrating clarinet reed.

Owing to the inspiration from the advancements in microfluidic device applications, we analyze linear stability and maximum energy growth amplification in rotating curved microchannel flows. We numerically investigate linear perturbations to a fully developed stable base flow in a rotating curved microchannel by employing the spectral collocation method after transforming the Navier–Stokes system into coupled Orr–Sommerfeld and Squire equations. We estimate the temporal growth rate of the Tollmein–Schlichting wave and the neutral stability bounds driven by the Coriolis and centrifugal forces. At low rotational numbers and small curvature of the channel, we identify four distinct modal instabilities based on the positive growth rate, even at a low Reynolds number within the range for microfluidic devices. By investigating marginal instabilities and critical parameter values, we propose designs for efficient and portable curved microchannels aimed at controlling mixing efficiency. The novelty of the present study is the introduction of curvature of a curved microchannel in a rotating system and its impact on Dean vortices, predicting an early transition to instabilities. Our findings reveal the unstable regions of transient energy growth in a rotating curved microchannel, as highlighted by numerical range and eigenspectrum. Eigenspectrum analysis cannot precisely estimate instabilities, but numerical ranges of transient energy growth offer this capability. In comparison to earlier studies, we report a lower critical Reynolds number of 44 and a critical Dean number of 20 for moderate rotation rates and small curvature of the channel. Employing the transient energy growth analysis, we determine the efficient mixing time, revealing a decreasing function of the Dean number. The concept presented here can potentially assist in the manipulation of interactions of multiple vortices for further studies in mixing phenomena. [ABSTRACT FROM AUTHOR]

This study is focused on optimizing electromagnetic acoustic transducer (EMAT) sensors for enhanced ultrasonic guided wave signal generation in steel cables using CAD and modern manufacturing to enable contactless ultrasonic signal transmission and reception. A lab test rig with advanced measurement and data processing was set up to test the sensors' ability to detect cable damage, like wire breaks and abrasion, while also examining the effect of potential disruptors such as rope soiling. Machine learning algorithms were applied to improve the damage detection accuracy, leading to significant advancements in magnetostrictive measurement methods and providing a new standard for future development in this area. The use of the Vision Transformer Masked Autoencoder Architecture (ViTMAE) and generative pre-training has shown that reliable damage detection is possible despite the considerable signal fluctuations caused by rope movement. [ABSTRACT FROM AUTHOR]

The study presents a unifying methodology for characterizing micromixers, integrating both experimental and simulation techniques. Focusing on Dean mixer designs, it employs an optical evaluation for experiments and a modified Sobolev norm for simulations, yielding a unified dimensionless characteristic parameter for the whole mixer at a given Reynolds number. The results demonstrate consistent mixing performance trends across both methods for various operation points. This paper also proposes enhancements in the evaluation process to improve accuracy and reduce noise impact. This approach provides a valuable framework for optimizing micromixer designs, essential in advancing microfluidic technologies. [ABSTRACT FROM AUTHOR]

Rough surfaces in microchannels effectively enhance liquid mixing, thermal performance, and chemical reactions in electrically actuated microfluidic devices. Rotation of the microchannel with surface roughness intensifies this enhancement. We investigate the combined effects of electromagnetohydrodynamics and surface roughness on transient rotating flow in microchannels. We present a mathematical model considering the variable zeta potential, heat transfer characteristics, and entropy generation within the microchannel. We obtain analytical solutions using the separation of variables method and Fourier series expansion. The surface roughness of the microchannel, when combined with rotation, impacts the temperature enhancement. Higher rotation rates result in the formation of multiple vortices. The secondary flow pushes the primary velocity toward the boundary layer, which affects the flow pattern. Surface roughness and electroosmotic flow significantly affect secondary flow, resulting in complex flow patterns and reversals. The interaction between centrifugal and viscous forces results in maximum velocities at the boundary layers. Higher roughness and electromagnetic effects enhance temperature by intensifying fluid-solid friction and joule heating. Surface roughness causes an increase in wall shear stress and friction factor, resulting in a higher Poiseuille number. Moreover, surface roughness increases entropy production by enhancing fluid mixing and internal friction despite improved heat transfer. Higher rotation also elevates entropy generation due to additional vortices induced by secondary flow. [ABSTRACT FROM AUTHOR]

Monitoring tanks and vessels play an important part in public infrastructure and several industrial processes. The goal of this work is to propose a new kind of guided acoustic wave sensor for measuring immersion depth. Common sensor types such as pressure sensors and airborne ultrasonic sensors are often limited to non-corrosive media, and can fail to distinguish between the media they reflect on or are submerged in. Motivated by this limitation, we developed a guided acoustic wave sensor made from polyethylene using piezoceramics. In contrast to existing sensors, low-frequency Hanning-windowed sine bursts were used to excite the L(0,1) mode within a solid polyethylene rod. The acoustic velocity within these rods changes with the immersion depth in the surrounding fluid. Thus, it is possible to detect changes in the surrounding media by measuring the time shifts of zero crossings through the rod after being reflected on the opposite end. The change in time of zero crossings is monotonically related to the immersion depth. This relative measurement method can be used in different kinds of liquids, including strong acids or bases. [ABSTRACT FROM AUTHOR]

Humidity, salt content, and migration in building materials lead to weathering and are a common challenge. To understand damage phenomena and select the right conservation treatments, knowledge on both the amount and distribution of moisture and salt load in the masonry is crucial. It was shown that commercial portable devices addressing moisture are often limited by the mutual interference of these values. This can be improved by exploiting broadband radar reflectometry for the quantification of humidity in historic masonry. Due to the above-mentioned limitations, today's gold standard for evaluating the moisture content in historic buildings is still conducted by taking drilling samples with a subsequent evaluation in a specially designed laboratory, the so-called Darr method. In this paper, a new broadband frequency approach in the range between 0.4 and 6 GHz with improved artificial-intelligence data analysis makes sure to optimize the reflected signal, simplify the evaluation of the generated data, and minimise the effects of variables such as salt contamination that influence the permittivity. In this way, the amount of water could be determined independently from the salt content in the material and an estimate of the salt load. With new machine learning algorithms, the analysis of the permittivity is improved and can be made accessible for everyday use on building sites with minimal intervention by the user. These algorithms were trained with generated data from different drying studies on single building bricks from the masonries. The findings from the laboratory studies were then validated and evaluated on real historic buildings at real construction sites. Thus, the paper shows a spatially resolved and salt-independent measurement system for determining building moisture. [ABSTRACT FROM AUTHOR]

The incident second harmonic wave is a problematic issue for the precise measurement of the acoustic nonlinearity parameter. This paper proposes a compensation method to remove the effect of the incident second harmonic component in the measurement of the absolute acoustic nonlinearity parameter using the calibration method. For this, the second harmonic component detected by the receiving transducer is considered as the sum of the component due to material nonlinearity and the component included in the incident signal and a numerical calculation model is developed as a function of the propagation distance. In the model, the factors related to the material nonlinear parameter and the magnitude of the incident second harmonic component are unknown and these are determined by finding a value that best matches the experimental data according to the change in the propagation distance; compensation for the incident second harmonic component is then achieved. The case where the phase of the second harmonic wave due to material nonlinearity is opposite to that of the fundamental wave is also considered. To verify the validity of the proposed method, fused silica and aluminum alloy Al6061-T6 specimens with different thicknesses corresponding to the propagation distance are tested. The experimental results show that the nonlinear parameters changed significantly according to the propagation distance before compensation but were very stable after compensation. Additionally, the average values of the nonlinear parameter are 11.04 in the fused silica, which is within the literature value range (10.1 to 12.4), and that for the Al6061-T6 is 6.59, which is close to the literature value range (4.5 to 6.12). [ABSTRACT FROM AUTHOR]

In the process of drilling, severe downhole vibration causes attitude measurement sensors to be erroneous; the errors will accumulate gradually during the inclination calculation. As a result, the ultimate well path could deviate away from the planned trajectory. In order to solve this problem, this paper utilized the stochastic resonance (SR) and chaos phase transition (CPT) produced by the second-order Duffing system to identify the frequency and estimate the parameters of the signal during measurement while drilling. Firstly, the idea of a variable-scale is introduced in order to reconstruct the frequency of the attitude measurement signal, and an SR frequency detection model based on a scale transformation Duffing system is established in order to meet the frequency limit condition of the SR. Then, an attitude measurement signal with a known frequency value is input into the Duffing chaos system, and the scale transformation is used again to make the frequency value meet the parameter requirement of chaos detection. Finally, two Duffing oscillators with different initial phases of their driving signal are combined in order to estimate the amplitude and phase parameters of the measurement signal by using their CPT characteristics. The results of the laboratory test and the field-drilling data demonstrated that the proposed algorithm has good immunity to the interference noise in the attitude measurement sensor, improving the solution accuracy of the inclination in a severe noise environment and thus ensuring the dynamic stability of the well trajectory. [ABSTRACT FROM AUTHOR]

Underwater noise produced by rainfall is an important component of underwater ambient noise. For example, the existence of rainfall noise causes strong disturbances to sonar performance. The underwater noise produced by a single raindrop is the basis of rainfall noise. Therefore, it is necessary to study the associated underwater noise when drops strike the water surface. Previous research focused primarily on the sound pressure and frequency spectrum of underwater noise from single raindrops, but the study on its sound energy is insufficient. The purpose of this paper is to propose a method for predicting the acoustic energy generated by raindrops of any diameter. Here, a formula was derived to calculate the underwater sound energy radiated by single raindrops based on a dipole radiation pattern. A series of experiments were conducted to measure the underwater sound energy in a 15 m × 9 m × 6 m reverberation tank filled with tap water. The analysis of the acoustic energy characteristics and conversion efficiency from kinetic to acoustic energy helped develop the model to predict the average underwater sound energy radiated by single raindrops. Using this model, the total underwater sound energy of all raindrops during a rainfall event can be predicted based on the drop size distribution. [ABSTRACT FROM AUTHOR]

The array invariant technique has been recently proposed for passive source localization in the ocean. It has successfully estimated the source–receiver horizontal range in multipath-dominant shallow-water waveguides. However, it requires a relatively large-scale hydrophone array. This study proposes an array invariant method that uses acoustic intensity, which is a vector quantity that has the same direction as the sound wave propagating through a water medium. This method can be used to estimate not only the source–receiver horizontal range, but also the azimuth to an acoustic source. The feasibility of using a vector quantity for the array invariant method is examined through a simulation and an acoustic experiment in which particle velocity signals are obtained using a finite difference approximation of the pressure signals at two adjacent points. The source localization results estimated using acoustic intensity are compared with those obtained from beamforming of the acoustic signals acquired by the vertical line array. [ABSTRACT FROM AUTHOR]

Damage is an inevitable occurrence in metallic structures and when unchecked could result in a catastrophic breakdown of structural assets. Non-destructive evaluation (NDE) is adopted in industries for assessment and health inspection of structural assets. Prominent among the NDE techniques is guided wave ultrasonic testing (GWUT). This method is cost-effective and possesses an enormous capability for long-range inspection of corroded structures, detection of sundries of crack and other metallic damage structures at low frequency and energy attenuation. However, the parametric features of the GWUT are affected by structural and environmental operating conditions and result in masking damage signal. Most studies focused on identifying individual damage under varying conditions while combined damage phenomena can coexist in structure and hasten its deterioration. Hence, it is an impending task to study the effect of combined damage on a structure under varying conditions and correlate it with GWUT parametric features. In this respect, this work reviewed the literature on UGWs, damage inspection, severity, temperature influence on the guided wave and parametric characteristics of the inspecting wave. The review is limited to the piezoelectric transduction unit. It was keenly observed that no significant work had been done to correlate the parametric feature of GWUT with combined damage effect under varying conditions. It is therefore proposed to investigate this impending task. [ABSTRACT FROM AUTHOR]

A general multipurpose microchip technology platform for point-of-care diagnostics has been developed. Real-time nucleic acid sequence-based amplification (NASBA) for detection of artificial human papilloma virus (HPV) 16 sequences and SiHa cell line samples was successfully performed in cyclic olefin copolymer (COC) microchips, incorporating supply channels and parallel reaction channels. Samples were distributed into 10 parallel reaction channels, and signals were simultaneously detected in 80 nl volumes. With a custom-made optical detection unit, the system reached a sensitivity limit of 10(-6) microM for artificial HPV 16 sequences, and 20 cells microl(-1) for the SiHa cell line. This is comparable to the detection limit of conventional readers, and clinical testing of biological samples in polymer microchips using NASBA is therefore possible.