Search

Magnesium batteries have attracted considerable attention as a promising technology for future energy storage because of their capability to undergo multiple charging reactions. However, most oxide materials utilized as hosts for magnesium batteries do not perform well at room temperature or in nonaqueous electrolytes. Herein, a host material, Na0.04MoO3·(H2O)0.49 is successfully developed through the chemical reduction of alpha‐MoO3, which enables magnesium storage reaction in a 0.5 m Mg(ClO4)2/acetonitrile electrolyte at 25 °C. Electrochemical analysis reveals that the cathode material possesses a discharge capacity of 157.4 mAh g−1 at a 0.2 C rate. The Na0.04MoO3·(H2O)0.49 cathode material also exhibits a capacity retention of 93.4% after 100 cycles compared to the first cycle at a 2 C rate, with an average discharge voltage of −0.474 V versus activated carbon (≈2.16 V estimated discharge voltage vs Mg/Mg2+). The study findings demonstrate, for the first time, the potential of this material as a cathode for magnesium batteries at ambient temperatures and in nonaqueous electrolytes.

Battery technologies based in multivalent charge carriers with ideally two or three electrons transferred per ion exchanged between the electrodes have large promises in raw performance numbers, most often expressed as high energy density, and are also ideally based on raw materials that are widely abundant and less expensive. Yet, these are still globally in their infancy, with some concepts (e.g. Mg metal) being more technologically mature. The challenges to address are derived on one side from the highly polarizing nature of multivalent ions when compared to single valent concepts such as Li ^+ or Na ^+ present in Li-ion or Na-ion batteries, and on the other, from the difficulties in achieving efficient metal plating/stripping (which remains the holy grail for lithium). Nonetheless, research performed to date has given some fruits and a clearer view of the challenges ahead. These include technological topics (production of thin and ductile metal foil anodes) but also chemical aspects (electrolytes with high conductivity enabling efficient plating/stripping) or high-capacity cathodes with suitable kinetics (better inorganic hosts for intercalation of such highly polarizable multivalent ions). This roadmap provides an extensive review by experts in the different technologies, which exhibit similarities but also striking differences, of the current state of the art in 2023 and the research directions and strategies currently underway to develop multivalent batteries. The aim is to provide an opinion with respect to the current challenges, potential bottlenecks, and also emerging opportunities for their practical deployment.

Abstract Among extensively studied Li‐ion cathode materials, LiCoO2 (LCO) remains dominant for portable electronic applications. Although its theoretical capacity (274 mAh g−1) cannot be achieved in Li cells, high capacity (≤240 mAh g−1) can be obtained by raising the charging voltage up to 4.6 V. Unfortunately, charging Li‐LCO cells to high potentials induces surface and structural instabilities that result in rapid degradation of cells containing LCO cathodes. Yet, significant stabilization is achieved by surface coatings that promote formation of robust passivation films and prevent parasitic interactions between the electrolyte solutions and the cathodes particles. In the search for effective coatings, the authors propose RbAlF4 modified LCO particles. The coated LCO cathodes demonstrate enhanced capacity (>220 mAh g−1) and impressive retention of >80/77% after 500/300 cycles at 30/45 °C. A plausible mechanism that leads to the superior stability is proposed. Finally the authors demonstrate that the main reason for the degradation of 4.6 V cells is the instability of the anode side rather than the failure of the coated cathodes.

Lithium sulfur batteries are suitable for drones due to their high gravimetric energy density (2600 Wh/kg of sulfur). However, on the cathode side, high specific capacity with high sulfur loading (high areal capacity) is challenging due to the poor conductivity of sulfur. Shuttling of Li-sulfide species between the sulfur cathode and lithium anode also limits specific capacity. Sulfur-carbon composite active materials with encapsulated sulfur address both issues but require expensive processing and have low sulfur content with limited areal capacity. Proper encapsulation of sulfur in carbonaceous structures along with active additives in solution may largely mitigate shuttling, resulting in cells with improved energy density at relatively low cost. Here, composite current collectors, selected binders, and carbonaceous matrices impregnated with an active mass were used to award stable sulfur cathodes with high areal specific capacity. All three components are necessary to reach a high sulfur loading of 3.8 mg/cm2 with a specific/areal capacity of 805 mAh/g/2.2 mAh/cm2. Good adhesion between the carbon-coated Al foil current collectors and the composite sulfur impregnated carbon matrices is mandatory for stable electrodes. Swelling of the binders influenced cycling retention as electroconductivity dominated the cycling performance of the Li-S cells comprising cathodes with high sulfur loading. Composite electrodes based on carbonaceous matrices in which sulfur is impregnated at high specific loading and non-swelling binders that maintain the integrated structure of the composite electrodes are important for strong performance. This basic design can be mass produced and optimized to yield practical devices.

Abstract A novel type of Li/graphene oxide (Li/GO) battery based on a spontaneous redox reaction between Li metal and GO cathode is introduced as an alternative viable primary battery system. Here, we present an efficient synthesis of GO by the modified Hummers method and focus on a comprehensive study of the reduction mechanism. The Li/GO battery was thoroughly analyzed by various physical and electrochemical methods. GO rich in oxygen‐bearing functional groups on graphene layers provided lithium storage sites and delivered a high discharge capacity of around 720 mAh/g at 12 mA/g. Products formed on the surface during reduction were analyzed, and a mechanism was proposed. The results uncovered the reasons underlying the improved electrochemical properties and the contribution of the irreversible capacity of reduced GO in graphene‐based composite electrode materials for metal‐ion batteries. The Li/GO concept is expected to shed light on the design of similar M/GO batteries based on other active metal anodes (e.g., M = Na, Mg, Al, Zn).

Thin porous layers are largely used, but a reliable method to quantify their porosity is missing. Here the authors demonstrate a method, based on quartz crystal microbalance measurements with dissipation monitoring, for accurate assessment of porosity and mechanical properties in thin porous films.

The interfacial electrochemical characteristics of unpassivated Mg metal electrodes have been studied using Staircase Galvano Electrochemical Impedance Spectroscopy (SGEIS) in THF/C6H5MgCl/AlCl3 solutions over a wide range of applied dc currents. The results shed light on the mechanism of electrochemical deposition and dissolution of Mg. We found that at the stationary condition (at the OCV, when no current flows) there is a very high interfacial charge-transfer resistance of around 40,000 Ωcm2. The impedance decreases to several hundred Ωcm2 when dynamic, though steady, processes of Mg deposition or dissolution take place. The alternating process through which impedance spectroscopy is measured is superimposed on this system. We show that the high impedance measured at the OCV with a low direct current is due to interfacial adsorption phenomena. However, the adsorption phenomena affect the interfacial charge transfer in different ways depending on the direction of the reaction. During steady-state deposition, the adsorbed layer leads to a large distance for electron tunneling, which translates to a high charge-transfer impedance across the interface. Application of relatively large steady-state negative currents leads to changes in the composition of the adsorbed layer and a significant reduction in the charge-transfer resistance. During the opposite process, dissolution, the high interfacial impedance measured is probably predominantly due to migration of Mg ions away from the Mg metal surface, across the adsorbed layer, to the bulk solution. At relatively high direct currents (and overpotentials >100 mV) the interfacial resistivity obeys Butler–Volmer kinetics, which are not complicated by adsorption phenomena.

In continuation of the work on the stabilization of the electrochemical performance of Li and Mn‐rich LixNiyCozMnwO2 (HE‐NCM, x > 1, w > 0.5, x + y + z + w = 2) cathode materials via atomic layer deposition (ALD) surface coatings, herein, the active role of aluminum oxides‐based coatings, during prolonged cycling in battery prototypes with graphite anodes, is discussed. Notable progress in electrochemical cycling and rate performance of Na‐aluminate‐coated Li1.142Mn0.513Ni0.230Co0.115O2 cathode material is established. These coated electrodes delivered a stable discharge capacity of 145 mAh g−1 (66% retention), compared to only 118 mAh g−1 (55% retention) for the uncoated sample at a 1.0 C rate after 400 cycles. Steady average discharge potential, lower voltage hysteresis, and stable energy density profiles are the noteworthy achievements for the coated material during cycling. Significant improvement in the coated material's thermal stability compared with the uncoated one has also been confirmed. The present study also enlightens about the Na‐aluminate coating's orientation and distribution on HE‐NCM material's surface. 23Na and 27Al solid‐state nuclear magnetic resonance (NMR) studies reveal the Na‐aluminate coating's crystalline constituent's disappearance upon cycling. The partial dissolution of Na5AlO4 coating, followed by forming a secondary disordered edge‐site phase that remains even after long‐term cycling, is disclosed.

Aqueous salt batteries with high concentrations of salt or water in salt aqueous systems have received considerable attention with focus on improving working voltage range and energy density. Here, the effect of NaClO4 salt concentration on the electrochemical performance and stability of tunnel-type Na0.44MnO2 (NMO) cathodes and organic polyimide (PI) derivative anodes was studied. High capacity retention and 100% coulombic efficiency were shown for NMO/PI full cell in saturated NaClO4 electrolyte. A high, stable capacity of 115 mAh/g was achieved for the PI anode material, and the full cell showed a stable capacity of 41 mAh/g at 2C rate for 430 cycles (calculated for the weight of NMO cathode). Even at a fast 5C rate, a discharge capacity of 33 mAh/g was maintained for 2,400 prolonged cycles with nearly 100% efficiency. The full cell device can achieve an average voltage of 1 V with energy density of 24 Wh/kg. This study highlights concentrated sodium perchlorate as a promising electrolyte solution for stabilization of electrodes and enhancement of electrochemical performance in aqueous media.

High-energy cathode materials that are Li- and Mn-rich lithiated oxides—for instance, 0.35Li2MnO3.0.65LiNi0.35Mn0.45Co0.20O2 (HE-NCM)—are promising for advanced lithium-ion batteries. However, HE-NCM cathodes suffer from severe degradation during cycling, causing gradual capacity loss, voltage fading, and low-rate capability performance. In this work, we applied an effective approach to creating a nano-sized surface layer of Li2SO4 on the above material, providing mitigation of the interfacial side reactions while retaining the structural integrity of the cathodes upon extended cycling. The Li2SO4 coating was formed on the surface of the material by mixing it with nanocrystalline Li2SO4 and annealing at 600 °C. We established enhanced electrochemical behavior with ~20% higher discharge capacity, improved charge-transfer kinetics, and higher rate capability of HE-NCM cathodes due to the presence of the Li2SO4 coating. Online electrochemical mass spectrometry studies revealed lower CO2 and H2 evolution in the treated samples, implying that the Li2SO4 layer partially suppresses the electrolyte degradation during the initial cycle. In addition, a ~28% improvement in the thermal stability of the Li2SO4-treated samples in reactions with battery solution was also shown by DSC studies. The post-cycling analysis allowed us to conclude that the Li2SO4 phase remained on the surface and retained its structure after 100 cycles.

The main descriptors of chemical bonding such as bond order (BO) and electron density at the bond critical point, ρc, are customarily used to understand the crystal and electronic structure of materials, as well as to predict their reactivity and stability. They can be obtained in the framework of crystal chemistry and quantum chemistry approaches, which are mostly applied as alternatives to each other. This paper verifies the convergence of the two approaches by analyzing a plethora of quantum chemistry data available in the literature. The exponential correlation between the electron descriptors [BOij and ρc(ij)] and the length of chemical bonds, Rij, which is basic in crystal chemistry, was confirmed for 72 atom pairs, regardless of the nature of their interactions (ionic/covalent, metal–metal, etc.). The difference between the BOij (Rij) correlations obtained in this work and those accepted in crystal chemistry for the same atomic pairs does not exceed the dispersion of quantum chemistry data, confirming the qualitative validity of the BO conservation principle. Various examples are presented to show that knowledge of the exponential parameters ensures a surprisingly simple determination of two basic electron descriptors in any complex compound with known interatomic distances. In particular, the BO analysis for 20 Re6-cluster complexes illustrates the BO conservation for systems with delocalized electrons. Despite the significant transfer of electron density from the Re–Re to the Re–ligand bonds, the total number of Re valence electrons used in bonding remains close to the formal value of seven electrons.

The solid-electrolyte interphase formed on Li-battery electrodes strongly affects their cycling performance, however the mechanical properties of the surface films are not well-known. Here the authors report a sensitive gravimetric/viscoelastic method to probe surface film formation on composite electrodes, coupled with Li-ion intercalation.

Most of TM6-cluster compounds (TM = transition metal) are soluble in polar solvents, in which the cluster units commonly remain intact, preserving the same atomic arrangement as in solids. Consequently, the redox potential is often used to characterize structural and electronic features of respective solids. Although a high lability and variety of ligands allow for tuning of redox potential and of the related spectroscopic properties in wide ranges, the mechanism of this tuning is still unclear. Crystal chemistry approach was applied for the first time to clarify this mechanism. It was shown that there are two factors affecting redox potential of a given metal couple: Lever’s electrochemical parameters of the ligands and the effective ionic charge of TM, which in cluster compounds differs effectively from the formal value due to the bond strains around TM atoms. Calculations of the effective ionic charge of TMs were performed in the framework of bond valence model, which relates the valence of a bond to its length by simple Pauling relationship. It was also shown that due to the bond strains the charge depends mainly on the atomic size of the inner ligands.

In this work, we continued our systematic investigations on synthesis, structural studies, and electrochemical behavior of Ni-rich materials Li[NixCoyMnz]O2 (x + y + z = 1; x ≥ 0.8) for advanced lithium-ion batteries (LIBs). We focused, herein, on LiNi0.85Co0.10Mn0.05O2 (NCM85) and demonstrated that doping this material with high-charge cation Mo6+ (1 at. %, by a minor nickel substitution) results in substantially stable cycling performance, increased rate capability, lowering of the voltage hysteresis, and impedance in Li-cells with EC-EMC/LiPF6 solutions. Incorporation of Mo-dopant into the NCM85 structure was carried out by in-situ approach, upon the synthesis using ammonium molybdate as the precursor. From X-ray diffraction studies and based on our previous investigation of Mo-doped NCM523 and Ni-rich NCM811 materials, it was revealed that Mo6+ preferably substitutes Ni residing either in 3a or 3b sites. We correlated the improved behavior of the doped NCM85 electrode materials in Li-cells with a partial Mo segregation at the surface and at the grain boundaries, a tendency established previously in our lab for the other members of the Li[NixCoyMnz]O2 family.

About 70 years ago, in the framework of his theory of chemical bonding, Pauling proposed an empirical correlation between the bond valences (or effective bond orders (BOs)) and the bond lengths. Till now, this simple correlation, basic in the bond valence model (BVM), is widely used in crystal chemistry, but it was considered irrelevant for metal–metal bonds. An extensive analysis of the quantum chemistry data computed in the last years confirms very well the validity of Pauling’s correlation for both localized and delocalized interactions. This paper briefly summarizes advances in the application of the BVM for compounds with TM–TM bonds (TM = transition metal) and provides further convincing examples. In particular, the BVM model allows for very simple but precise calculations of the effective BOs of the TM–TM interactions. Based on the comparison between formal and effective BOs, we can easily describe steric and electrostatic effects. A possible influence of these effects on materials stability is discussed.

This work continues our systematic study of Li- and Mn- rich cathodes for lithium-ion batteries. We chose Li2MnO3 as a model electrode material with the aim of correlating the improved electrochemical characteristics of these cathodes initially activated at 0 °C with the structural evolution of Li2MnO3, oxygen loss, formation of per-oxo like species (O22−) and the surface chemistry. It was established that performing a few initial charge/discharge (activation) cycles of Li2MnO3 at 0 °C resulted in increased discharge capacity and higher capacity retention, and decreased and substantially stabilized the voltage hysteresis upon subsequent cycling at 30 °C or at 45 °C. In contrast to the activation of Li2MnO3 at these higher temperatures, Li2MnO3 underwent step-by-step activation at 0 °C, providing a stepwise traversing of the voltage plateau at >4.5 V during initial cycling. Importantly, these findings agree well with our previous studies on the activation at 0 °C of 0.35Li2MnO3·0.65Li[Mn0.45Ni0.35Co0.20]O2 materials. The stability of the interface developed at 0 °C can be ascribed to the reduced interactions of the per-oxo-like species formed and the oxygen released from Li2MnO3 with solvents in ethylene carbonate–methyl-ethyl carbonate/LiPF6 solutions. Our TEM studies revealed that typically, upon initial cycling both at 0 °C and 30 °C, Li2MnO3 underwent partial structural layered-to-spinel (Li2Mn2O4) transition.