Search

Large-scale energy storage plants based on power-to-gas-to-power technologies incorporating high temperature electrolysis, catalytic methanation of H₂ and CO₂ and novel, highly efficient methane-fired Allam reconversion cycles allow for a confined and circular use of CO₂ and thus an emission-free storage of intermittent renewable energy. The Allam power cycle is considered as a beneficial power plant concept, which employs supercritical CO₂ as working fluid as well as an oxy-combustion process to reach high efficiencies of up to 66%. The combination of said process chain could reach a maximum roundtrip efficiency of 54.2 % assuming the presence of sufficient storage capacities for all relevant technical gases. In a technically feasible scenario, paired with a separate air separation unit instead of stationary O₂ storages, roundtrip efficiencies of 49.0 % were determined.. The implementation of said energy storage systems into existing national energy systems will pose a major challenge, since they will require far-reaching infrastructural changes to the respective systems itself, such as extensive installations of renewable generation and electrolysis capacities as well as sufficient subsurface storage capacities for both CO₂ and CH₂. Furthermore, an exemplary energy system forecast for Germany for the year of 2050 is presented to show the viability of the energy storage concept. In case of a fully circular use of CO₂, when electricity is solely generated by renewable energy sources (RES), 736 GW of RES, 234 GW of electrolysis and 62 GW of gas-to-power capacities are required. The total storage volume on the national scale of Germany for both CO₂ and CH₄ was determined to be 7.8 billion Nm³, respectively, leading to a CH₄ storage capacity of 54.5 TWh. The present investigation illustrates the feasibility of large-scale energy storage systems for renewable electricity based on high temperature electrolysis, catalytic methanation and Allam power cycles paired with lar

Germany 2050For the first time Germany reached a balance between its sources of anthropogenic CO2 to the atmosphere and newly created anthropogenic sinks. This backcasting study presents a fictional future in which this goal was achieved by avoiding (∼645 Mt CO2), reducing (∼50 Mt CO2) and removing (∼60 Mt CO2) carbon emissions. This meant substantial transformation of the energy system, increasing energy efficiency, sector coupling and electrification, energy storage solutions including synthetic energy carriers, sector-specific solutions for industry, transport and agriculture, as well as nature-based and technological carbon dioxide removal. All of the above was necessary to achieve a net-zero CO2 system for Germany by 2050.

The thermochemical energy storage properties of calcium hydride (CaH2) destabilised with either silicon (Si) or CaxSiy compounds at various molar ratios, were thoroughly studied by a combination of experimental and computer assisted thermodynamic calculations. Particularly, the destabilisation effect of Si on CaH2 at five different molar ratios (1:1, 1:2, 2:1, 3:4, 5:3 CaH2 to Si) was extensively investigated. Theoretical calculations predicted a multi-step thermal decomposition reaction between CaH2 and Si forming CaxSiy at varying temperatures, which was confirmed by in-situ synchrotron X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis and mass-spectroscopic measurements. The most suitable destabilisation reactions between CaH2 and Si or CaxSiy that meet the criteria of a thermal energy storage system for the next-generation of concentrated solar power (CSP) plants were identified. The CaH2 and CaSi system (in a 2:3 molar ratio of CaH2 to CaSi) showed desirable operating conditions with a decomposition temperature of 747 ± 33 °C at a hydrogen pressure of 1 bar. Pressure composition isothermal measurements were conducted on this system to determine its practical enthalpy of decomposition to form Ca5Si3. The calculated value (107.3 kJ mol−1 H2) was lower compared to the experimentally determined value (154 ± 4 kJ mol−1 H2). This mismatch was mainly due to the formation of CaO and a CaSi solid solution in addition to the desired Ca5Si3 phase.

© 2020 The Authors Globally, the accelerating use of renewable energy sources, enabled by increased efficiencies and reduced costs, and driven by the need to mitigate the effects of climate change, has significantly increased research in the areas of renewable energy production, storage, distribution and end-use. Central to this discussion is the use of hydrogen, as a clean, efficient energy vector for energy storage. This review, by experts of Task 32, “Hydrogen-based Energy Storage” of the International Energy Agency, Hydrogen TCP, reports on the development over the last 6 years of hydrogen storage materials, methods and techniques, including electrochemical and thermal storage systems. An overview is given on the background to the various methods, the current state of development and the future prospects. The following areas are covered; porous materials, liquid hydrogen carriers, complex hydrides, intermetallic hydrides, electrochemical storage of energy, thermal energy storage, hydrogen energy systems and an outlook is presented for future prospects and research on hydrogen-based energy storage.

Magnesium hydride owns the largest share of publications on solid materials for hydrogen storage. The “Magnesium group” of international experts contributing to IEA Task 32 “Hydrogen Based Energy Storage” recently published two review papers presenting the activities of the group focused on magnesium hydride based materials and on Mg based compounds for hydrogen and energy storage. This review article not only overviews the latest activities on both fundamental aspects of Mg-based hydrides and their applications, but also presents a historic overview on the topic and outlines projected future developments. Particular attention is paid to the theoretical and experimental studies of Mg-H system at extreme pressures, kinetics and thermodynamics of the systems based on MgH 2 , nanostructuring, new Mg-based compounds and novel composites, and catalysis in the Mg based H storage systems. Finally, thermal energy storage and upscaled H storage systems accommodating MgH 2 are presented.

In the past decades, complex hydrides and complex hydrides-based materials have been thoroughly investigated as materials for energy storage, owing to their very high gravimetric and volumetric hydrogen capacities and interesting cation and hydrogen diffusion properties. Concerning hydrogen storage, the main limitations of this class of materials are the high working temperatures and pressures, the low hydrogen absorption and desorption rates and the poor cyclability. In the past years, research in this field has been focused on understanding the hydrogen release and uptake mechanism of the pristine and catalyzed materials and on the characterization of the thermodynamic aspects, in order to rationally choose the composition and the stoichiometry of the systems in terms of hydrogen active phases and catalysts/destabilizing agents. Moreover, new materials have been discovered and characterized in an attempt to find systems with properties suitable for practical on-board and stationary applications. A significant part of this rich and productive activity has been performed by the research groups led by the Experts of the International Energy Agreement Task 32, often in collaborative research projects. The most recent findings of these joint activities and other noteworthy recent results in the field are reported in this paper.

Metal hydrides are known as a potential efficient, low-risk option for high-density hydrogen storage since the late 1970s. In this paper, the present status and the future perspectives of the use of metal hydrides for hydrogen storage are discussed. Since the early 1990s, interstitial metal hydrides are known as base materials for Ni – metal hydride rechargeable batteries. For hydrogen storage, metal hydride systems have been developed in the 2010s [1] for use in emergency or backup power units, i. e. for stationary applications. With the development and completion of the first submarines of the U212 A series by HDW (now Thyssen Krupp Marine Systems) in 2003 and its export class U214 in 2004, the use of metal hydrides for hydrogen storage in mobile applications has been established, with new application fields coming into focus. In the last decades, a huge number of new intermetallic and partially covalent hydrogen absorbing compounds has been identified and partly more, partly less extensively characterized. In addition, based on the thermodynamic properties of metal hydrides, this class of materials gives the opportunity to develop a new hydrogen compression technology. They allow the direct conversion from thermal energy into the compression of hydrogen gas without the need of any moving parts. Such compressors have been developed and are nowadays commercially available for pressures up to 200 bar. Metal hydride based compressors for higher pressures are under development. Moreover, storage systems consisting of the combination of metal hydrides and high-pressure vessels have been proposed as a realistic solution for on-board hydrogen storage on fuel cell vehicles. In the frame of the “Hydrogen Storage Systems for Mobile and Stationary Applications” Group in the International Energy Agency (IEA) Hydrogen Task 32 “Hydrogen-based energy storage” different compounds have been and will be scaled-up in the near future and tested in the range of 500 g to several hundre

Magnesium hydride owns the largest share of publications on solid materials for hydrogen storage. The “Magnesium group” of international experts contributing to IEA Task 32 “Hydrogen Based Energy Storage” recently published two review papers presenting the activities of the group focused on magnesium hydride based materials and on Mg based compounds for hydrogen and energy storage. This review article not only overviews the latest activities on both fundamental aspects of Mg-based hydrides and their applications, but also presents a historic overview on the topic and outlines projected future developments. Particular attention is paid to the theoretical and experimental studies of Mg-H system at extreme pressures, kinetics and thermodynamics of the systems based on MgH2, nanostructuring, new Mg-based compounds and novel composites, and catalysis in the Mg based H storage systems. Finally, thermal energy storage and upscaled H storage systems accommodating MgH2 are presented.

Porous Al scaffolds were synthesised and melt-infiltrated with various eutectic metal borohydride mixtures (0.725LiBH4-0.275KBH4, 0.68NaBH4-0.32KBH4, 0.4NaBH4-0.6 Mg(BH4)2) to simultaneously act as both a confining framework and a reactive destabilising agent for H2 release. The scaffolds were synthesised by sintering a pellet of NaAlH4/2 mol%TiCl3 at 450 °C under dynamic vacuum. During the sintering process the sodium alanate (NaAlH4) decomposed to Al metal. The vacuum applied at elevated temperature promoted the Na metal to vaporise and be extruded from the pellet. The pores of the resulting Al scaffold were created during removal of the H2 and the Na from the body of the NaAlH4/2 mol%TiCl3 pellet. According to the morphological observations carried out by a Scanning Electron Microscope (SEM), melt-infiltrated eutectic mixtures of metal borohydrides were highly dispersed into the porous scaffolds. Temperature Programmed Desorption (TPD) experiments, revealed that the melt-infiltrated samples exhibited faster H2 desorption kinetics in comparison to bulk samples, with onset temperatures (Tdes) lower than the bulk by 150–250 °C. The as-synthesised porous Al scaffolds acted as a reactive containment vessel for these eutectic mixtures that simultaneously nanoconfined and destabilised the mixtures.