Search

Aim: Composite restorations often have gingival margins near the cemento-enamel junction (CEJ), where the microleakage of these margins can significantly contribute to the restoration failure, especially in the cervical lesions. It is important to determine the microleakage is crucial, as it typically occurs through the interfacial gap between the tooth and the restoration. Various resin composites and techniques have been developed to minimize this gap and reduce the risk of microleakage. The aim of this in vitro study was to evaluate the levels of microleakage of different modes of a universal adhesive and two novel resin composites in restoring class V cavities in the central incisors., Methods: Sixty-six freshly extracted sound human central incisors of the similar size were randomly assigned to 2 groups (n = 33 per group) according to the brand of resin composite. Each group was further divided into 3 subgroups based on the Scotch Bond Universal (3 M ESPE, Saint Paul, MN, USA) application protocol used: (a) total etch, (b) self-etch and (c) selective etch. After composite restoration completed with Omnichroma (Tokuyama Dental Corp., Tokyo, Japan) and Filtek Universal Restorative (3 M ESPE, Saint Paul, MN, USA), each tooth was immersed in a 0.5% basic fuchsin dye solution at 37C 0 for 24 h. After dye penetration, teeth were sectioned and evaluated with conventional (scoring) and digital methods (ImageJ). The intra- and inter-examiner agreement was estimated according to the Kappa statistics and the results were analyzed with the one-way ANNOVA and the Kruskal-Wallis test (p < 0.05)., Results: The rates of microleakage of the gingival and incisal margins are statistically similar, regardless of the composite brand and the method of application of the universal adhesive., Conclusion: The microleakage exhibited by current adhesives and resins is independent of the adhesive application mode and measurement method., Competing Interests: Declarations Ethics approval and consent to participate This study was conducted according to the stipulations of the Helsinki Declaration (2000) and previously approved by the Research Ethics Committee the Gazi University under protocol number E-21071282–050.99–60064. All teeth were extracted due to periodontal reasons and all patients and/or legal guardians gave their written informed consent for the use of their teeth for research purposes and all central incisors were irreversibly anonymized immediately after extraction. Consent for publication Not applicable. Competing interests The authors declare no competing interests., (© 2024. The Author(s).)

Objective: To compare the microleakage of MTA (mineral trioxide aggregate) and resin-modified GIC (glass ionomer vitremer) as retrograde endodontic material., Study Design: Experimental study., Place and Duration of Study: Operative Department of DIIKIOHS (DUHS) and NED University, Karachi, from February to June 2014., Methodology: Forty human anterior teeth were divided into four groups. Each tooth was endodontically treated. Apical cavity preparations were performed on all teeth. The retropreparations were filled either with MTA (Group 1), Vitremer (Group 2), or only covered with nail polish (Group 3). The root surfaces of the first three groups were coated with nail polish. In Group 4 (positive control), neither retrograde filling was placed nor the nail polish was applied. The teeth were then suspended in 2% methylene blue dye solution for 10 days at 37°C. Sections were made along the long axis of teeth to determine the depth of linear dye penetration. Using Mann-Whitney test the comparison, p-value <0.05 was considered as statistically significant., Results: MTA had no significant difference in apical dye leakage (p = 0.122) than did the vitremer., Conclusion: MTA is equivalent to vitremer in preventing microleakage when used as retrograde filling material.

Objective: The present study examined the effect of a quaternary ammonium silane (QAS) cavity disinfectant on the viability of human dental pulp cells, dentine bond durability and nanoleakage of simplified etch-and-rinse adhesives., Methods: Etched dentine surface of third molars were randomly divided into two adhesive groups, Adper™ Single Bond 2 and Prime & Bond ® NT™. For each adhesive, the teeth were randomly assigned to five cavity disinfectant groups (N=6): Group 1: deionised water (control); Group 2: 2% chlorhexidine (CHX); Group 3: 2% QAS; Group 4: 5% QAS and Group 5: 10% QAS. The cavity disinfectants were applied on etched dentine surfaces for 20s, followed by adhesive application. The bonded teeth were sectioned for bond strength testing at 24h, 6 months and 12 months. Viability of human dental pulpal cells was examined using MTT assay. Bond strength data were analysed using 3-way ANOVA and Tukey test. Interfacial nanoleakage was evaluated after 24h and 12 months and analysed using Kruskal-Wallis test., Results: Significant differences in bond strength were observed for the factors disinfectants (p<0.001) and time (p<0.001); while the factor, adhesive, was not significantly different (p=0.203). The 2% QAS cavity disinfectant preserved bond strength of both adhesives and reduced interfacial nanoleakage after 12 months. Cell viability was the lowest for 2% CHX, followed by 2% QAS and the control., Conclusions: The 2% QAS cavity disinfectant demonstrated greater cell viability compared to 2% CHX, with no adverse effect on immediate bond strength and preserved bond stability over time., Clinical Significance: Incorporation of 2% quaternary ammonium silane cavity disinfectant in the resin-dentine bonding protocol enhances the success rate of bonded restorations., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Introduction: Coronal leakage is one of the constant concerns in routine dental practice. It is one of the factors responsible for the failure of root canal therapy. Permanent restorations should be given as soon as possible after the completion of root canal therapy. If unavoidable, provisional restoration should be given in such a way that it maximally reduced the leakage of microorganisms and fluids from the external environment into the canal space. Hence, we evaluated the effect of saliva on the coronal leakage of temporary restorations., Materials and Methods: Biomechanical preparation of the root canals of 204 fresh mandibular first premolar teeth was done using endodontic files with intermittent irrigation of sodium hypochlorite solution and ethylenediaminetetraacetic acid. Alternate irrigation with normal saline was done periodically. After preparation, drying of the canals was done using paper points followed by sealing of the apical foramen. For the assessment of the microleakage, Siqueira et al apparatus and method was used. All the specimens were divided into four groups based on the provisional restorative material used. All the groups were further divided into three subgroups based on the presence and absence of intracanal medicaments. Verissimo et al's criteria were used to check the turbidity at 1-, 2-, 3-, and 4-week interval respectively. All the results were analyzed by Statistical Package for the Social Sciences (SPSS) software. Chi-square test was used to measure the level of significance, and p < 0.05 was considered to be significant., Results: In group I, all the subgroups' specimens showed significant difference at 1 week's time. Only the subgroup with no intracanal medicaments in Cavit-containing provisional restoration showed nonsignificant alterations. Statistically significant alterations were seen at 1, 2, and 3 weeks' interval in all the subgroups except for one with intracanal medicaments., Conclusion: All the temporary restorative materials were not able to prevent microleakage after 1 week's time, with worst bacterial resistance shown by Ketac Molar and ionomer restorative material. Future studies are advocated for better prognosis of root canal therapy.

Objective: To evaluate the coronal microleakage of packable composite using conventional incremental and posterior bulk fill flowable composite using Smart Dentine Replacement Single Step technique in the cervical margins of class II cavities in dentine using the dye penetration method., Study Design: In-vitroInterventional study., Place and Duration of Study: Department of Operative Dentistry, Dr. Ishrat-ul-Ebad Khan Institute of Oral Health Sciences (DIKIOHS), Karachi, from November 2012 to April 2013., Methodology: One hundred and twenty extracted teeth (molars and premolars) were collected and randomly divided into two experimental groups (n=60 each) and were stored in normal saline until used. Fractured samples were excluded. Standardized class II proximal box only cavities were prepared and restored with conventional methacrylate based composite using incremental technique (Group A, n=40) and low stress methacrylate resin based composite SDR using single step technique (Group B, n=40). Samples were sectioned horizontally below the cervical margins and specimen disks were prepared. The specimens were thermocycled and sealed with acid resistant varnish leaving a 1-mm interface around cervical margin and immersed in 2% methylene blue buffered solution for 24 hours. Leakage was scored 0 - 4 and measured in mm. It washed and sectioned to evaluate under stereomicroscope., Results: Mean penetration was 2.4280 ±0.79 mm for Group Aand 1.015 ±0.45 mm for Group B (p < 0.001). Maximum dye penetration score for group Awas 4 and group B was 3., Conclusion: SDR technique in combination with total etch technique at the cervical margin of class II restorations improved the marginal seal, when were placed in dentine and thermocycled.

Aim: Carbomer cement represents a novel glass-ionomer which gradually mineralises into fluoroapatite. Purpose of this study was to evaluate microleakage around restorations in deciduous teeth made with composite resin, conventional glass-ionomer cement, resin-modified glass-ionomer cement and carbomer/fluoroapatite-enhanced glass-ionomer cement., Materials and Methods: A group of 40 primary upper canines, primary upper and lower molars was divided into 4 groups (n=10). Class I cavities were prepared by diamond cylindrical bur at high speed and were restored with a composite resin (Group 1), with a glass- ionomer cement (Group 2), with a resin-modified glass-ionomer cement (Group 3) and with a carbomer/fluoroapatite-enhanced glass- ionomer cement (Group 4). Hard tissue's bonding involved, in the case of composite resin a total etch bonding procedure, and in glass ionomers the use of their respective primers. Restorations were finished and polished. A 24-hour water storage was followed by thermocycling (1500 cycles, 5°C - 36°C - 55°C - 36°C with a dwell time of 15 seconds) and dye penetration test with immersion in 5% methylene blue for 24 hours. In order to assess the degree of microleakage longitudinal cuts were produced by means of a microtome at 0.5 mm and at 1 mm from the restoration margin, and photographs were taken with a stereomicroscope at 100X. Microleakage was classified according to the number of surfaces and the depth at which dye penetration was observed. Data were analysed with ANOVA and post-hoc analysis was performed with Bonferonni test (p<0.05)., Results: Statistical analysis exhibited no significant statistical difference between Group 2 and Group 3 (p>0.05). Statistical difference was exhibited between Group 3 and Group 4 (p<0.01), with Group 4 exhibiting lower microleakage values. Group 1 exhibited the lowest mean microleakage values and statistical difference in comparison with all groups (p<0.001). Group 4 exhibited the lowest microleakage values among the cements., Conclusion: Superior marginal integrity is achieved in restored primary teeth when composite resin is used. If the clinical case suggests the use of a glass-ionomer cement, carbomer/fluoroapatite-enhanced glass-ionomer cement is prefered in terms of microleakage.

Aim: The aim of this study was to evaluate microleakage under orthodontic ceramic brackets bonded with direct and different indirect bonding techniques and adhesives using micro-computed tomography., Materials and Methods: A total of 30 human maxillary premolars were randomly separated into five groups with six teeth in each group. In group I, teeth were bonded directly with Transbond XT (3M Unitek). In group II, group III, group IV, and group V, teeth were bonded through an indirect technique with Custom I.Q. (Reliance Orthodontic Products), Sondhi Rapid-Set (3M Unitek), RMbond (RMO), and Transbond IDB (3M Unitek), respectively, following the manufacturer's instructions. Micro-CT system model 1172 of Skyscan (Kontich, Belgium) was used to scan all samples. NRecon (Skyscan) version 1.6, CT-Analyser V.1.11 (Skyscan), and TView (SkyScan, Bvba) software programs were used for microleakage evaluation. Microleakage values between the test groups were assessed using the Kruskal-Wallis test, while the Wilcoxon signed rank test was used for within-group comparisons. The level of significance was set at P < 0.05., Results: According to the Kruskal-Wallis analysis of variance test, there were no significant differences among the tested groups, with regard to volume and percentage (microleakage/region of interest × 100) of microleakage values (P < 0.05). The Wilcoxon signed rank test showed that coronal microleakage volume and percentage values significantly differed for RMbond and Transbond IDB groups., Limitations: In the study, only ceramic brackets were used and microleakage into mini gaps did not show up on the micro-CT image because 50% silver nitrate solution could not penetrate into mini gaps which are smaller than silver nitrate particles., Conclusion: Use of direct and indirect bonding techniques with different adhesives did not significantly affect the amount of microleakage., (© The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.)

Aim: The aim of this study was to evaluate the bond strength, penetration ability, microleakage, and remineralisation capacity of glass ionomer-based fissure sealant materials., Materials and Methods: In this study, three glass ionomer-based fissure sealants were evaluated (Fuji Triage, Fuji VII EP, and GCP Glass Seal). A dye-penetration test was performed to evaluate microleakage under a stereomicroscope. The materials were applied to occlusal tooth surfaces, and bucco-lingual sections (1 mm width) were assessed to evaluate the penetration ability. Shear bond strength of tested materials was assessed using a universal testing machine. Finally, the remineralisation capacities of the materials were evaluated with EDS., Results: The Fuji Triage exhibited the lowest microleakage and unfilled area proportion (p<0.05). The highest shear bond strength was calculated with Fuji VII EP (p<0.05). The fluoride content for all treatment groups was significantly different when remineralisation values were compared to demineralisation (p<0.05)., Conclusion: Both the Fuji Triage and Fuji VII EP yielded compatible and satisfactory results and all fissure sealants used in this study are sufficient as anti-caries agents.

Aim: To evaluate microleakage of Nanoionomer (3M ESPE Ketac(™) N100 Light cured Nanoionomer Restorative) and Nanocomposite (3M ESPE Filtek(™) Z350 XT Universal Restorative) restorations, immersed in fruit drink, fresh fruit juice and soft drink., Study Design: Eighty caries free maxillary premolars extracted for orthodontic purpose were used for the study. Class V cavities were prepared and restored with Nanocomposite on buccal surface and Nanoionomer on the palatal surface. The teeth were thermocycled following the restoration. The experimental groups comprised of 72 teeth (3 groups comprising 24 teeth each for fruit drink, fresh fruit juice and soft drink), while remaining 8 formed the control group. Each of experimental group was further divided into three subgroups (low, medium and high immersion). The teeth were finally immersed in Rhodamine B dye, sectioned and evaluated under stereomicroscope. Statistical analyses used were Mann-Whitney test and ANOVA test., Results: The teeth showed statistically significant microleakage as the immersion regime increased. Soft drink group showed highest microleakage followed by fresh fruit juice and fruit drink. Nanocomposite exhibited more microleakage but the comparison was not statistically significant., Conclusion: The three beverages used in the study affected the microleakage of both restorative materials significantly. The microleakage scores increased as the frequency of the immersions increased. Soft drink caused highest microleakage followed by fresh fruit juice and fruit drink.

Purpose: To evaluate the effect of an acid containing 2% chlorhexidine (Ac/CHX) or a 2% CHX aqueous solution (Aq/CHX) on the immediate and 5-year bonding properties of resin/dentin interfaces produced by two adhesives. The presence of CHX in these interfaces was also evaluated under micro-Raman spectroscopy., Materials and Methods: Forty-two molars were ground to expose a flat dentin surface. In the control group, the surfaces were etched with conventional phosphoric acid, and Prime&Bond NT (PB) and Adper Single Bond 2 (SB) were applied. In Ac/CHX, an acid containing 2% CHX was applied after adhesive application. In the Aq/CHX group, an aqueous solution of 2% CHX was applied for 60 s after etching. After placing the restoration, specimens were prepared and tested using the microtensile bond strength test (μTBS, 0.5 mm/min) immediately or after 5 years. For nanoleakage (NL), specimens at each period were immersed in silver nitrate solution and examined by EDX-SEM. In addition, specimens at each period underwent examination for CHX using micro-Raman spectroscopy. Data were submitted to appropriate statistical analysis (a=0.05)., Results: After 5 years, NL was more pronounced in the control than in the Ac/CHX or Aq/CHX (p<0.001). Significant reductions in the μTBS were observed for all groups; however, they were more pronounced for the control (p<0.001). CHX was still present in the hybrid layers Ac/CHX or Aq/CHX groups after 5 years., Conclusion: The use of a 2% chlorhexidine-containing acid or the application of an aqueous CHX primer may increase the long-term stability of resin/dentin interfaces.

Purpose: Achieving optimal moisture inside the root canal is a challenge during bonding of fiberglass posts. This study evaluated the effect of different moisture patterns on the push-out bond strength (PBS) and nanoleakage (NL) of fiber posts bonded to the root canal of two simplified etch-and-rinse adhesives., Materials and Methods: The roots of 72 human premolars were endodontically prepared and divided into 6 groups according to the combination of the main factors: adhesive (Ambar and Adper Single Bond 2) and moisture (dry, wet, and overwet). The posts were cemented and after 1 week, the roots were cross sectioned into 6 disks. Two disks each were obtained from the cervical, middle, and apical thirds, and the PBS test was carried out (0.5 mm/min; n = 8). The NL was evaluated by scanning electron microscopy after the immersion of specimens in 50% silver nitrate (n = 4). The failure pattern was examined on all debonded specimens. Data were analyzed by three-way repeated measures ANOVA and Tukey's test (5%)., Results: For both adhesives, higher PBS values and lower NL were observed in the wet groups, and lower PBS and higher NL in the dry group. In general, the overwet condition showed intermediate results., Conclusions: The root dentin walls should be left slightly moist before performing fiber post cementation procedures.

Objectives: To assess leakage of class-I restorations using a gas-enhanced permeation test (GEPT) as compared with conventional SEM or dye analysis., Materials and Methods: Pressure differences over time and penetrating water volumes were measured simultaneously in a two-chamber system (GEPT) before and after class I cavity preparation in 30 molars. Ten teeth were restored with a composite restoration without bonding (A1), a composite restoration with bonding (A2) or a ceramic indirect restoration (B). Five intact teeth served as controls (C). Another GEPT measurement was performed and impressions were taken. Teeth were subjected to thermodynamic loading (1 200 000 cycles) and final GEPT measurements and impressions were made. SEM evaluation of the marginal continuity was performed and teeth were subjected to a Fuchsin dye penetration test. Spearman's rank test was used to compare results from different tests., Results: The GEPT and SEM values did not correlate before loading (0.359, p = 0.051), but significantly correlated afterwards (0.662, p < 0.0001). The correlations between the Fuchsin dye penetration test and GEPT and SEM surface marginal analysis were significant (0.777 and 0.534, p-values < 0.0001 and 0.002, respectively)., Conclusions: SEM marginal analysis was mainly limited in reflecting the surface restoration integrity. GEPT evaluation may, therefore, serve as a tool to non-destructively assess restoration sub-surface integrity over time., Clinical Relevance: The current study provided proof that restoration margin quality does not necessarily reflect its leakage behaviour.

Purpose: To investigate the influence of three cavity designs on the marginal seal of large Class II cavities restored with low-shrinkage resin composite limited to the enamel., Materials and Methods: One hundred twenty (120) intact human molars were randomly divided into 12 groups, with three different cavity designs: 1. undermined enamel, 2. box-shaped, and 3. proximal bevel. The teeth were restored with 1. an extra-low shrinkage (ELS) composite free of diluent monomers, 2. microhybrid composite (Herculite XRV), 3. nanohybrid composite (Filtek Supreme XTE), and 4. silorane-based composite (Filtek Silorane). After artificial aging by thermocycling and storage in physiological saline, epoxy resin replicas were prepared. To determine the integrity of the restorations' approximal margins, two methods were sequentially employed: 1. replicas were made of the 120 specimens and examined using SEM, and 2. the same 120 specimens were immersed in AgNO3 solution, and the dye penetration depth was observed with a light microscope. Statistical analysis was performed using the Kruskal-Wallis and the Dunn-Bonferroni tests., Results: After bevel preparation, SEM observations showed that restorations did not exhibit a higher percentage of continuous margin (SEM-analysis; p>0.05), but more leakage was found than with the other cavity designs (p<0.05). The lowest percentage of continuous margin was observed in ELS restorations (p<0.05). More fractured margins were observed in the undermined enamel cavity design groups (p<0.05)., Conclusion: Bevel preparation failed to improve margin quality in large Class II composite restorations and is no longer recommended. However, undermined enamel should be removed to prevent enamel fractures.

Objective: To evaluate the effect of ethanolic extracts of propolis (EEP) addition in different proportions to glass ionomer cement (GIC) on microleakage and microhardness of GIC., Study Design: The cement was divided into four groups: one using the original composition and three with 10%, 25%, and 50% EEP added to the liquid and then manipulated. For microleakage assessment, sixty primary molars were randomly divided into four groups (n=15). Standard Class II cavities were prepared and then filled with EEP in different proportions added to GICs. Microleakage test was performed using a dye penetration method. The data were analyzed using one-way ANOVA and Mann-Whitney U tests (α = 0.05). Disc shaped specimens were prepared from the tested GIC to determine Vickers hardness (VHN). The data were analyzed using one-way ANOVA and post hoc Tukey test (α = 0.05)., Results: There were no statistically significant differences between the groups in terms of microleakage (p > 0.05). There were statistically significant differences between the VHN values of groups (p < 0.05). Increasing addition of EEP to GIC statistically significantly increased VHN value of GIC (p < 0.05)., Conclusions: The addition of EEP to GIC increased the microhardness of the GIC and did not adversely affect the microleakage. Thus, it might be used during routine dental practice due to its antibacterial properties.

Purpose: To evaluate the effect of a scrubbing technique with one-step self-etching adhesives on bond strengths and nanoleakage expression at the resin/dentin interface., Materials and Methods: Flat human dentin surfaces bonded with one of two mild self-etching adhesives, SE One (SE) or Scotchbond Universal (SU) applied either with scrubbing or without scrubbing technique, were prepared (n = 5). The microtensile bond strengths (μTBS), SE micrographs of morphological changes on treated dentin surfaces, and expression of nanoleakage along the bonded dentin interfaces as shown with TEM were evaluated. μTBS data were analyzed using two-way ANOVA and the post-hoc t-test at the significance level of 0.05., Results: The scrubbing technique had a significant positive effect on the μTBS of SU (p < 0.05), while it produced no significant difference for SE (p > 0.05). Morphological evaluation of the treated dentin surfaces demonstrated that SU with scrubbing showed the highest etching ability, followed by scrubbing SE > nonscrubbing SE > nonscrubbing SU. In the nonscrubbing groups, nanoleakage formation using SU exhibited a reticular pattern throughout the hybridized complex, whereas with SE, water-tree nanoleakage was only found in the adhesive layer at dentinal tubule orifices. The scrubbing groups of both adhesives did not exhibit any nanoleakage expression., Conclusion: Using a scrubbing technique when applying mild self-etching adhesives could improve resin monomer infiltration into dentin, chase water on adhesive surfaces, and facilitate smear layer removal.

Purpose: To evaluate the microtensile bond strength (μTBS) and marginal sealing ability of a self-adhering flowable composite between dentin and composite interfaces, as well as the microleakage of Class V restorations., Materials and Methods: The occlusal thirds of 40 third molars were removed and randomly divided into 4 groups according to the applied adhesive: Adper Easy One (AEO, 3M ESPE), Clearfil SE Bond (CSEB, Kuraray), Prime & Bond NT (PBNT, Dentsply) and a self-adhering flowable composite (Dyad Flow, DF, Kerr). Filtek Flowable (3M ESPE) resin composite crowns were then built up in the first three groups; in group DF, composite crowns were built up without the application of an adhesive. Thirty stick-shaped microspecimens were prepared per group, 10 of which were used for morphological observation of bonded interfaces by scanning electron microscopy (SEM) after decalcification. The remaining microspecimens underwent microtensile bond strength testing and the failure mode was analyzed. Microleakage evaluation was performed on 10 premolars per group in which standardized box-shaped Class V cavities were prepared. After 500 thermocycles, the premolars were immersed in 1% methylene blue for 24 h, and three slices from each tooth were observed under a stereomicroscope and scored. Statistical analysis was performed using one-way ANOVA, Student-Newman-Keuls and chi-square tests., Results: The PBNT group presented the highest μTBS values, followed by the CSEB and AEO groups, which did not differ significantly from each other. The DF group showed the lowest μTBS values. No significant differences in microleakage were observed among these four groups., Conclusion: Although individual usage of the self-adhering flowable composite showed the lowest bond strength, the same marginal sealing ability was observed as that of combining self-etching and etch-and-rinse adhesives with flowable composite.

Purpose: To evaluate shear bond strength and microleakage of a new self-etching/self-adhesive fissure sealant on prismless enamel compared with conventional fissure sealing., Materials and Methods: A total of 90 extracted third molars were assigned to 3 main groups: group 1: self-etching/self-adhesive sealant, without acid etching; group 2: self-etching/self-adhesive sealant, with prior acid etching; group 3: conventional fissure sealing (control group). After specimen preparation, each group was divided into 3 subgroups according to storage time (1-day water storage, 3-month water storage, and 1-day water storage followed by 5000x thermocycling). The shear bond strength was determined with a universal testing machine, according to ISO standard 29022. Afterwards, the failure mode was analyzed. An additional 24 third molars were used for microleakage assessment. The fissure pattern was sealed in strict accordance with the manufacturers' instructions. After thermocycling, the dye penetration was examined. Data were analyzed using the Mann-Whitney U-Test at a significance level of 0.05., Results: The shear bond strength of the self-etching/self-adhesive fissure sealant without prior acid etching was significantly lower (4.3 MPa) than that of the self-etching/self-adhesive fissure sealant with prior acid etching (17.1 MPa) and the conventional fissure sealing (19.1 MPa). Microleakage was significantly lower in the control group (1.1%) and in the group with the self-etching/self-adhesive sealant with prior acid etching (0.8%) compared to the group that used the self-etching/self-adhesive material alone (49.4%)., Conclusion: The self-etching/self-adhesive fissure sealant can be recommended for clinical use when enamel is etched with phosphoric acid. The self-etching/self-adhesive sealant without prior acid etching showed significantly inferior results.

Aim: The aim of the present study was to determine the effect of ethylenediaminetetraacetic acid (EDTA) and NaOCl irrigation on the microleakage and interfacial morphology of adhesives bonded to pulp chamber dentin., Methods: The pulp chamber roof of 72 extracted permanent molars was removed. Samples were equally divided into six groups. Pulp chamber dentin was bonded with either Adper Easy One (group 1), Adper Prompt L-Pop (group 2), or Adper Single Bond 2 (Group 3), after irrigation with either normal saline (groups 1a, 2a, 3a) or 17% EDTA and 5.25% NaOCl (groups 1b, 2b, 3b). Composite resin restorations were placed in the pulp chamber. Ten samples per group were subjected to microleakage test and scanning electron microscopic analysis was done in two samples from each group. Data were statistically analyzed using Mann-Whitney and Kruskal Wallis tests at a significance level of P < 0.05., Results: EDTA and NaOCl irrigation of the pulp chamber significantly reduced microleakage in Adper Easy One. However, it had no significant effect on the microleakage of Adper Prompt L-Pop and Adper Single Bond 2., Conclusions: EDTA and NaOCl irrigation of the pulp chamber was not deleterious to the bonding of any of the adhesives tested. While this irrigation regimen had no significant effect on the microleakage of Adper Prompt L-Pop and Adper Single Bond 2, it significantly reduced the microleakage scores in Adper Easy One., (© 2014 Wiley Publishing Asia Pty Ltd.)

Objective: To evaluate the sealing ability of two different types of Glass Ionomer Cements (GICs) used for sandwich restorations and assess the effect of acid etching of GIC on microleakage at GIC-resin composite interface., Study Design: Experimental study., Place and Duration of Study: Department of Operative, DIEKIOHS (DUHS) and NED University, Karachi, from February to June 2011., Methodology: Eighty cavities were prepared on the proximal surfaces of 40 permanent human premolars (2 cavities per tooth), assigned to 4 groups (n=20) and restored as follows: Group CIE - Conventional GIC (CI) was applied onto the axial and cervical cavity walls, allowed setting for 5 minutes and acid etched (E) along the cavity margins with 37% phosphoric acid for 15 seconds, washed for 30 seconds and dried; the adhesive system was applied and light cured for 10 seconds, completing the restoration with composite resin light cured for 40 seconds; Group CIN - same as Group CIE, except for acid etching of the CI surface; Group RME - same as CIE, but using a resin modified GIC (RMGIC); Group RMN - same as Group RME, except for acid etching of the RMGIC surface. Specimens were soaked in 1% methylene blue dye solution at 37&ordm;C for 24 hours, rinsed under running water for 15 minutes, bisected mesiodistally and dye penetration was measured following the ISO/TS 11405-2003 standard. Kruskal Wallis and post Hoc tests significant differences in the microleakage among all the four groups., Results: There was a significant difference between the two groups of GICs (RMGIC and CI, p=0.001). There was no significant difference in between the two sub-groups that is between CIN and CIE (p=0.656), and between Groups RME and RMN (p=0.995)., Conclusion: Phosphoric acid etching of GIC, prior to the placement of composite resin, does not improve the sealing ability of sandwich restorations. RMGIC was more effective in preventing dye penetration at the GIC-resin composite dentine interfaces than CI.

Background/objectives: A new flash-free adhesive promises to eliminate the need to clean up excess adhesive upon orthodontic bracket bonding. This study evaluated this new adhesive with regard to microleakage at the enamel-bracket interface, amount of adhesive remaining on the tooth after bracket debonding, time required for adhesive remnant cleanup, and clinical practitioners' preference in comparison to a conventional adhesive., Materials/methods: A total of 184 bovine incisors were bonded with ceramic brackets using either the flash-free adhesive (APC Flash-Free Adhesive Coated Appliance System, 3M Unitek [3M], Monrovia, California, USA) or a conventional adhesive (APCII Adhesive Coated Appliance System, 3M). Twenty-four of the teeth were scanned using microcomputed tomography to quantify microleakage into the adhesive layer. Twenty orthodontists debonded the brackets, removed the remaining adhesive, and then completed a survey regarding their preference for one of the two adhesives. The adhesive remnant was quantified and the time required for its removal recorded. Differences between the adhesives were tested for statistical significance., Results: For both adhesives, the microleakage was minimal with no significant differences between the two adhesives. The adhesive remnant was significantly larger for the flash-free adhesive, whereas there was no significant difference in adhesive cleanup time. Fourteen out of the 20 orthodontists preferred the flash-free adhesive over the conventional adhesive., Limitations: In vitro testing cannot replicate the actual clinical situation during in vivo debonding., Conclusions: With regard to bond quality and adhesive remnant cleanup, the new flash-free adhesive performs just as well as the conventional adhesive, and, of the two products, is the one preferred by most orthodontists., (© The Author 2014. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.)

Aim: The aim of this study was to compare the sealing ability of mineral trioxide aggregate (MTA), Portland cement (PC), Biodentine(TM) and Tech biosealer in repairing furcal perforations in primary molars using the fluid-filtration technique., Materials and Methods: Fifty freshly extracted maxillary second primary molars were sectioned horizontally at the furcation region to create dentin disks of 1.5 mm (+ 0.1 mm) thickness. Five disks were not perforated and served as negative controls. In the remaining 45 disks, furcation perforations were prepared. Five disks did not receive furcation repair and served as positive controls. The remaining 40 disks were then randomly divided into four equal groups (10 disks in each group). Perforations were repaired with: MTA, PC, Biodentine(TM) or Tech Biosealer. The sealing ability of the tested materials was evaluated by measuring microleakage for each disk after four different storage periods: 24-hour, 1-month, 6-month and 1-year storage using fluid-filtration. Comparisons between the four materials and the four time periods were done using the two-way analysis of variance and the Scheffe multiple comparisons test., Results: There was no significant difference between the mean microleakage values obtained in the four tested materials after 24 hours, 1, 6 month and 1 year. However, microleakage values for each individual material were significantly higher at 24 hours than at the other time intervals., Conclusion: Mineral trioxide aggregate, PC, Biodentine(TM) and Tech biosealer showed similar capabilities in sealing the furcal perforations of the primary molars, where the sealing ability improved over time for each individual material.

Aim: This study was carried out to evaluate and compare solubility and microleakage of the newly introduced moisture tolerant glass carbomer sealant., Study Design: For evaluation of solubility, 20 specimens of glass carbomer and conventional glass ionomer were prepared and immersed in artificial saliva of pH 4 and 6 for seven days. The difference between initial and final weight was calculated. For evaluation of microleakage, glass carbomer was compared with a conventional resin sealant. 20 premolar teeth indicated for orthodontic extraction were collected and divided into two groups and the respective sealants were applied. It was subjected to thermocycling and then kept immersed in methylene blue for 24 hours. Dye penetration was scored., Results: The glass carbomer specimens were less soluble than the conventional glass ionomer at both pH values. There was no significant difference in the microleakage., Conclusion: Being moisture resistant, glass carbomer can be used as an alternative fissure sealant material; especially in young children with partially erupted teeth and where obtaining moisture control is difficult.

Purpose: This study evaluated the effect of aging solutions on the durability of resin-dentin bonds by means of microtensile bond strength (μTBS) and nanoleakage (NL) tests., Materials and Methods: The adhesive system Adper Single Bond 2 (3M ESPE) was applied according to the manufacturer's instructions to the flattened occlusal surface of 40 extracted human molars. After bonding, teeth were sectioned to obtain bonded sticks (0.8 mm2 area) which were tested in tension immediately or after different storage periods (1 week, 1 month, or 6 months). Bonded sticks were kept immersed in 5 different solutions: 1) distilled water (DW); 2) 99.9% propionic acid (PA); 3) 99% acetic acid (AA); 4) 75% ethanol (ET), and 5) mineral oil (MO). To determine NL, bonded sticks from each experimental condition were immersed in silver nitrate and analyzed by SEM. Data were analyzed by two-way repeated measure ANOVA and Tukey's test (α=0.05)., Results: Faster degradation of bond strength (1 week) could be seen for AA and ET (p<0.05) in comparison with DW. Specimens stored in PA and DW showed bond strengths significantly reduced after one and six months, respectively (p<0.05). No degradation of the resin-dentin bond strengths was observed for specimens stored in MO (p>0.05). Nanoleakage increased for all groups except MO after storage., Conclusion: Propionic acid, acetic acid, and ethanol can be used as alternative aging solutions to more quickly obtain results on the bond resistance to degradation.

Reducing collagen degradation within hybrid layers may contribute to the preservation of adhesive interfaces. This study evaluated the stability of resin-dentin interfaces treated with benzalkonium chloride (BAC)-modified adhesive blends and assessed collagen degradation in dentin matrices treated with BAC. The etch-and-rinse adhesive, Adper Single Bond Plus, modified with 0.5% and 1.0% BAC, was evaluated for microtensile bond strength (μTBS) and nanoleakage (NL) after 24 h and 1 yr. Thirty completely demineralized dentin beams from human molars were dipped for 60 s in deionized water (DW; control), or in 0.5% or 1.0% BAC, and then incubated in simulated body fluid (SBF). Collagen degradation was assessed by quantification of the dry mass loss and the amount of hydroxyproline (HYP) released from hydrolyzed specimens after 1 or 4 wk. Although all groups demonstrated a significant increase in NL after 1 yr, adhesive modified with 0.5% BAC showed stable bond strength after 1 yr (9% decrease) relative to the control (44% decrease). Significantly less HYP release and dry mass loss were observed for both 0.5% and 1.0% BAC relative to the control. This in vitro study demonstrates that BAC contributes to the preservation of resin-dentin bonds for up to 1 yr by reducing collagen degradation., (© 2015 Eur J Oral Sci.)

Purpose: To investigate the bonding of a new universal adhesive applied using different etching strategies on sound and caries-affected dentin of primary teeth., Materials and Methods: Flat dentin surfaces from 50 primary molars were randomly assigned to 10 groups according to substrate (sound dentin [SD] vs caries-affected dentin [CAD] pH cycled for 14 days) and bonding approach (Scotchbond Universal Adhesive: self-etching, vs dry or wet-bonding etch-and-rinse strategies; Adper Single Bond Plus [two-step etch-and-rinse adhesive] and Clearfil SE Bond [two-step self-etching system] as controls). After 24 h of water storage, bonded sticks with cross-sectional areas of 0.8 mm2 were tested for microtensile bond strength (μTBS). Two sticks from each tooth were immersed in silver nitrate solution in order to evaluate nanoleakage (NL) with SEM. The μTBS means were analyzed using two-way ANOVA and Tukey's tests. For NL, the Kruskal-Wallis and Mann-Whitney tests were used (α = 0.05)., Results: The influence of the etching strategy on the bonding performance of the universal adhesive was substrate dependent. The self-etching approach resulted in lower μTBS values and higher silver nitrate uptake into hybrid layers for Scotchbond Universal Adhesive on SD, while no difference among experimental groups was observed in CAD., Conclusion: It is preferable to use the universal adhesive following either a dry- or wet-bonding etch-and-rinse approach on both sound and caries-affected primary dentin.

Purpose: To evaluate the effect of different radiant exposure values delivered to two simplified etch-and-rinse adhesive systems on push-out bond strength (PBS) of fiber posts to root canal, as well as nanoleakage (NL) and in situ degree of conversion (DC) within the hybrid layer., Materials and Methods: The roots of human premolars were endodontically prepared and divided into 6 groups according to the combination of the main factors adhesive/resin cement (2 commercial brands) and radiant exposure (4, 16, 48, and 288 J/cm2). The posts were cemented and the PBS tested at 0.5 mm/min (n = 7). The NL (n = 3) was evaluated using SEM after immersion of specimens in 50% silver nitrate. Micro-Raman spectroscopy was performed to determine the in situ DC (n = 2). Data were analyzed by three-way repeated measures ANOVA and Tukey's post-hoc test (5%)., Results: PBS (MPa) showed a significant difference only for the middle third when an increase in radiant exposure from 4 to 16 J/cm2 or higher was used (p < 0.05). The NL (%) decreased significantly with increasing radiant exposure from 48 to 288 J/cm2 in the middle and apical thirds when compared to lower radiant exposure (p < 0.05). The radiant exposure of 288 J/cm2 significantly increased the DC (%) in the middle and apical thirds, compared the other radiant exposure values (p < 0.05)., Conclusion: The increase in radiant exposure delivered to the cervical third of root canals during post cementation improved the adhesive performance of simplified etch-and-rinse adhesive systems in the apical and middle thirds.

Aim: To evaluate the bonding temperature effect on dentin-restoration microleakage. The null hypothesis of the study is that the score of microleakage is identical among different adhesive bondings at different temperatures., Materials and Methods: Ninety caries free maxillary premolars were selected. Class V cavities were prepared on the cemento enamel junction (CEJ) of the buccal sides with enamel margins on occlusal sides and cementum margins on gingival sides. The specimens were divided into 3 groups: G1, single bond adhesive + Z250 composite; G2, P90 adhesive + Filtek Silorane composite; and G3, Clearfil SE bond + Clearfil APX. All groups were divided into three subgroups based on the adhesive temperature: A-4°C; B-25°C; and C-40°C. After coating the specimens with nail polish 1 mm beyond the margin of the restorations, they were stored in 0.5% basic Fuchsin dye solution for 24 hours. The teeth then were buccolingually sectioned and observed under a stereomicroscope., Results: There was no significant difference between microleakage of occlusal and gingival margins in each group. Clearfil SE bond and Adper single bond displayed lower microleakage than P90 adhesive at 4°C and 25°C. The most and least microleakage score for Adper single bond was at 40°C and 25°C respectively. Clearfil SE bond showed less microleakage at 25°C than 4°C and 40°C., Conclusion: Clearfil SE bond and Adper single bond displayed less microleakage at 25°C while there was no significant difference among for P90 adhesive microleakage at three temperatures.

Aim: To evaluate the effect of different surface pre-treatment methods on the microleakage of self-adhesive flowable composites (SAFCs) in comparison with a conventional flowable composite applied with an etch-and-rinse adhesive system., Materials and Methods: One hundred and thirty-five standardised Class V cavities were randomly divided into nine groups: (1) three-step etch-and-rinse adhesive (Optibond FL - Kerr, Orange, USA)/flowable composite (Clearfil Majesty Flow - Kuraray, Tokyo, Japan) (E&Ra/flowC); (2) Fusio Liquid Dentin (Pentron Clinical, Orange, USA); (3) Er:YAG Laser/Fusio Liquid Dentin (Er&Las/Fusio Liquid Dentin); (4) Phosphoric Acid/Fusio Liquid Dentin (PhosA/Fusio Liquid Dentin); (5) Polyacrylic Acid/Fusio Liquid Dentin (PolyA/Fusio Liquid Dentin); (6) Vertise Flow (Kerr, Orange, USA); (7) Er:YAG Laser/Vertise Flow (Er&Las/Vertise Flow); (8) Phosphoric Acid/Vertise Flow (PhosA/Vertise Flow); (9) Polyacrylic Acid/Vertise Flow (PolyA/Vertise Flow). After thermocycling and immersion in a 0.5% basic fuchsin, the restorations were evaluated under a stereomicroscope (n = 30). The data were statistically analysed (α = 0.05)., Results: Both SAFCs showed higher leakage scores than E&Ra/flowC in enamel and dentin (p < 0.05). Vertise Flow showed lower leakage than Fusio Liquid Dentin in dentin (p < 0.05). Pre-phosphoric acid etching reduced the microleakage scores of Fusio Liquid Dentin in both enamel and dentin (p < 0.05), while all surface pre-treatment methods led to a significant reduction in the microleakage scores of Vertise Flow at the enamel margin (p < 0.05)., Conclusion: Pre-etching of enamel and dentin by phosphoric acid may be satisfactory in improving the sealing ability of Fusio Liquid Dentin, while phosphoric acid or polyacrylic acid etching or laser irradiation may be used to improve the adhesion of Vertise Flow to enamel.

Objective: The purpose of this study was to analyze the sealing ability of different temporary endodontic materials over a 6-week period using a glucose penetration model., Materials and Methods: Standardized holes were formed on 48 dentin discs from human premolars. The thicknesses of the specimens were distributed evenly to 2 mm, 3 mm and 4 mm. Prepared dentin specimens were randomly assigned into six groups (n = 7) and the holes in the dentin specimens were filled with two kinds of temporary filling materials as per the manufacturers' instructions as follows: Caviton (GC Corporation, Tokyo, Japan) 2 mm, 3 mm, 4 mm and IRM (Dentsply International Inc., Milford, DE) 2 mm, 3 mm, 4 mm. The remaining specimens were used as positive and negative controls and all specimens underwent thermocycling (1000; 5-55°C). The sealing ability of all samples was evaluated using the leakage model for glucose. The samples were analyzed by a spectrophotometer in quantitative glucose microleakage test over a period of 6 weeks. As a statistical inference, a mixed effect analysis was applied to analyze serial measurements over time., Results: The Caviton groups showed less glucose penetration in comparison with the IRM groups. The Caviton 4 mm group demonstrated relatively low glucose leakage over the test period. High glucose leakage was detected throughout the test period in all IRM groups. The glucose leakage level increased after 1 week in the Caviton 2 mm group and after 4 weeks in the Caviton 3 mm and 4 mm groups (p < 0.05)., Conclusions: Caviton had better sealing ability than IRM in the glucose penetration model during 6 weeks. Temporary filling of Caviton to at least 3 mm in thickness is necessary and temporary filling periods should not exceed 4 weeks.

Purpose: To evaluate the marginal microleakage and the infiltration ability of pit-and-fissure sealants by applying the conventional sealing technique in comparison to using an additional bonding agent., Materials and Methods: Extracted non-carious permanent molars (n = 60) were first stored in sterile saline solution and then assigned to one of two groups: group C (control) was sealed (Helioseal F) by using the conventional technique, while in group BA (bonding agent), a bonding agent (OptiBond FL) was additionally applied prior to sealing. The teeth were thermocycled (1000 cycles, 5°C to 55°C, dwell time 30 s), then varnished and immersed in 5% methylene blue solution for 24 h. After embedding and sectioning each tooth into 6-12 slices, the presence of microleakage, unfilled areas, and air bubbles trapped in the sealant were assessed with a stereomicroscope., Results: A higher proportion of microleakage was found under sealants applied without the additional use of the bonding agent. A statistically significant difference in microleakage was noted between the groups (p = 0.045). Regarding the presence of unfilled areas, a statistically significant difference between the groups was observed (p < 0.001), especially since no unfilled areas were found at all in the samples of the group using the bonding agent. Regarding the amount of air bubbles trapped in the sealant, no statistically significant difference was observed between the two groups (p = 0.829)., Conclusion: Under these in vitro conditions, sealant procedures using an additional bonding agent applied beforehand significantly improved fissure infiltration and microleakage prevention significantly.

Purpose: This study assessed the effect of antioxidants vitamin C (Vit. C), vitamin E (Vit. E) and quercetin (Querc) on the dentin bonding performance, degree of conversion, and rate of polymerization of three commercial adhesive systems (Adper Single Bond 2 [SB], Clearfil SE Bond [CSE], Adper Easy Bond [EB])., Materials and Methods: Human premolars were restored using antioxidant-doped adhesives. The samples were stored for 24 h in distilled water or 6 months under simulated pulpal pressure. Teeth were cut into sticks and the microtensile bond strength (μTBS) to dentin was tested in a universal testing machine. Qualitative nanoleakage analysis was performed from a central stick of each restored tooth. Degree of conversion and rate of polymerization of adhesive systems were evaluated in triplicate using real-time FT-IR., Results: Although the inclusion of the antioxidants negatively affected the μTBS over 24 h, the antioxidant-doped adhesives maintained (SB-Vit. C, SB-Vit. E, CSE-Vit. C, EB-Querc) or increased (SB-Querc, CSE-Vit. E, CSE-Querc, EB-Vit. E, and EB-Vit. C) their μTBS during 6 months of storage. Only the μTBS of Adper Single Bond 2 dropped significantly after 6 months among the control groups. Slight changes in the nanoleakage pattern after aging were observed in all groups, except for the EB-control group, which showed a noteworthy increase in nanoleakage after 6 months, and for EB-Vit. C, which presented a remarkable decrease. A lower degree of conversion was obtained with all antioxidants in SB and EB, except for the EB-Vit. E group. Similar degrees of conversion were attained in control and experimental groups for CSE. The rate of polymerization was reduced in antioxidant-doped adhesives., Conclusion: The performance of antioxidants changed according to the adhesive system to which they were added, and antioxidant-doped adhesives appear to have a positive effect on the adhesive interface durability, since their bond strength obtained after 24 h was maintained or increased over time.

The objective of this investigation was to determine and decrease dye leakage of fast-setting mineral trioxide aggregate (FSMTA). Specimens using differing setting times or concentrations of calcium sulfate modified FSMTA were assessed for dye penetration. Based on the results, no statistical difference was found in the dye leakage of FSMTA compared with regular mineral trioxide aggregate (MTA). The addition of 10 percent calcium sulfate resulted in a statistical reduction in dye leakage compared to both unmodified FSMTA and regular MTA.

Aim: To evaluate the Influence of pH change and water storage up to 90 days on the sealing ability of two resin-based root-filling materials., Materials and Methods: Forty-four human mandibular single-rooted teeth were instrumented and filled with gutta-percha/ AH Plus or Resilon/Epiphany SE (n=20 per group). Two teeth each were used as positive and negative controls. Specimens were set for 7 days under 100% humidity at 37°C. They were allocated into two subgroups (n=10) according to whether they were tested immediately or stored for up to 90 days in water before testing. Sealing ability was evaluated by passive dye penetration. Absorbance at 630 nm (in μg/ml) was measured by spectrophotometry. The pH values were obtained in triplicate. Data were submitted to ANOVA by post-hoc Tukey's test (α=0.05)., Results: Specimens filled with Resilon/Epiphany SE exhibited more leakage than specimens filled with gutta-percha/AH Plus at the immediate time point (p<0.001). No differences were detected between the groups after storage, or between the materials with pH changes after 30, 60 and 90 days (p>0.05)., Conclusion: Gutta-percha/AH Plus provided superior sealing at the immediate time point. Water storage and pH changes did not Influence the sealing ability of tested materials., Clinical Significance: These results suggest that Resilon/ Epiphany SE sealer offered no apparent advantage over the more conventional gutta-percha/AH Plus sealer technique in terms of sealing ability.

An antibacterial monomer 12-methacryloyloxydodecylpyridinum bromide (MDPB)-containing experimental, chemically cured primer was prepared to develop a new resin-based root canal filling system. This study investigated the antibacterial effects of the MDPB-containing primer (experimental primer [EP]) against Enterococcus faecalis and assessed the in vitro bonding and sealing abilities of the filling system, consisting of EP and a Bis-GMA-based sealer resin. Antibacterial effects of EP were evaluated by contact with planktonic or adherent bacteria for 30 or 60 sec, and the viable bacterial number was counted. The antibacterial effects against E. faecalis in dentinal tubules were also assessed, according to a root canal infection model. Bonding and sealing abilities of the experimental filling system were examined by microtensile bond strength tests and leakage tests based on fluid filtration methods. Significantly greater reduction in viable bacteria in planktonic and adherent form was obtained by short-period contact with EP compared with the control primer (without MDPB) or with the proprietary (Epiphany) primer (p < .05). Significantly greater bactericidal effects of the EP inside the dentinal tubule of root, as opposed to the control primer or Epiphany primer, were confirmed according to a root canal infection model (p < .05), and 100% killing of E. faecalis could be obtained by the application of EP after irrigation with a 5% sodium hypochlorite solution. The experimental endodontic filling system demonstrated significantly greater bond strength to root dentin than Epiphany sealer system (Epiphany primer and Epiphany Root Canal Sealant; p < .05), showing formation of resin tags and a hybridized layer. Leakage tests clarified that the experimental system provided excellent sealing. This study confirmed that the MDPB-containing experimental antibacterial primer has the ability to effectively disinfect the root canal. Additionally, the experimental root canal filling system employing this primer and the Bis-GMA-based sealer resin is useful for achieving good sealing, suggesting its possible benefit for successful endodontic treatments., (© International & American Associations for Dental Research.)

Purpose: To evaluate the microleakage of Cerec 3, IPS e.max Press, and Turkom-Cera inlays cemented with three self-adhesive resin cements., Materials and Methods: Ninety standardized class III MOD cavities were prepared in intact human mandibular third molars. Ceramic inlays were fabricated according to the manufacturer's instructions and were cemented using three self-adhesive resin cements (RelyX Unicem, Smartcem 2, and SpeedCEM). The specimens were stored in distilled water at 37°C for 24 h and subjected to 1000 thermocycles in water between 5°C and 55°C with a dwell time of 30 s. Subsequently, the specimens were subjected to 100,000 cycles of mechanical loading of 50 N at 1.6 Hz in 37°C water. The specimens were immersed in 0.5% basic fuchsine for 24 h and were sectioned using a low-speed diamond blade. The percentage of dye leakage at the tooth/restoration interface was measured and compared by Kruskal-Wallis tests with Bonferonni correction and Mann-Whitney U-tests at a significance level of p<0.05., Results: Microleakage at the RelyX Unicem interface was lower than that with Smartcem 2 and SpeedCEM resin cements (p<0.05). Microleakage of the Turkom-Cera system was higher than Cerec 3 and IPS e.max Press ceramic inlays (p<0.05)., Conclusions: Regardless of the ceramic system and self-adhesive resin cement used, dentin margins were associated with higher microleakage than enamel margins.

Purpose: To evaluate the effect of enzyme-based (Papacárie) and sodium-hypochlorite-based (Carisolv) chemomechanical caries removal methods on bonding of self-etching adhesives to caries-affected dentin, in comparison to the standard rotary-instrument caries removal method., Materials and Methods: Seventy-eight carious permanent molars exhibiting frank cavitation into dentin were used. Forty-eight teeth were randomly divided into three groups, according to the caries excavation methods: (i) Papacárie, (ii) Carisolv and (iii) a round steel bur. After caries removal, each group was subdivided into two groups for two-step (Clearfil SE Bond) or one-step (Clearfil S3 Bond) self-etching adhesive application and resin composite buildups. Bonded specimens were sectioned into beams for microtensile bond strength testing. Bond strength data were analyzed using three-way ANOVA and Tukey's test. For interfacial nanoleakage evaluation using a field-emission scanning electron microscope, caries was similarly removed from the remaining thirty carious molars, bonding was performed as for bond strength testing, and the teeth were sectioned., Results: RESULTS of three-way ANOVA revealed that bond strength was significantly affected by "adhesive" (p<0.001) and "dentin" (p<0.001), but not "caries excavation methods" (p>0.05). The bond strength of the two-step self-etching adhesive was significantly higher than that of the one-step self-etching adhesive (p<0.001). Conversely, the bond strength of self-etching adhesives to sound dentin was significantly higher than to residual caries-affected dentin (p<0.001). Greater silver penetration was observed in the bonded interfaces of residual caries-affected dentin and in interfaces bonded with the one-step self-etching adhesive vs those bonded with the two-step self-etching adhesive., Conclusion: Chemomechanical caries removal did not affect the bonding of self-etching adhesives to caries-affected dentin as compared to caries excavation with rotary instruments.

Objectives: To compare the effects of four commonly used artificial ageing methods (water storage, thermocycling, NaOCl storage and pH cycling) on the degradation of adhesive-dentine interfaces., Methods: Fifty molars were sectioned parallel to the occlusal plane, polished and randomly divided into two adhesive groups: An etch-and-rinse adhesive Adper SingleBond 2 and a self-etch adhesive G-Bond. After the composite built up, the specimens from each adhesive group were sectioned into beams, which were then assigned to one of the following groups: Group 1 (control), 24h of water storage; Group 2, 6 months of water storage; Group 3, 10,000 runs of thermocycling; Group 4, 1h of 10% NaOCl storage; and Group 5, 15 runs of pH cycling. The microtensile bond strengths were then tested. The failure modes were classified with a stereomicroscope and representative interface was analyzed with a field-emission scanning electron microscopy (FESEM). Nanoleakage expression was evaluated through FESEM in the backscattered mode., Results: The four artificial ageing methods decreased the bonding strength to nearly 50% and increased the nanoleakage expression of both adhesive systems compared with the control treatment. Adhesive failures were the predominant fracture modes in all groups. However, differences in detailed morphology were observed among the different groups., Conclusions: Water storage, thermocycling, NaOCl storage and pH cycling could obtain similar degradation effectiveness through appropriate parameter selection. Each in vitro artificial ageing method had its own mechanisms, characteristics and application scope for degrading the adhesive-dentin interfaces., Clinical Significance: Water storage is simple, low-cost but time-consuming; thermocycling lacks of a standard agreement; NaOCl storage is time-saving but mainly degrades the organic phase; pH cycling can resemble cariogenic condition but needs further studies. Researchers focusing on bonding durability studies should be deliberate in selecting an appropriate ageing model based on the differences of test material, purpose and time., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Objectives: 10-Methacryloyloxy-decyl-dihydrogen-phosphate (10-MDP) is currently considered as one of the most effective functional monomers for dental bonding, this in part thanks to its long and relatively hydrophobic spacer chain, adequately separating the polymerizable from the phosphate functionalities. This study compared functional monomers with different spacer chains' length and hydrophilicity to 10-MDP on their dentin and enamel bonding performance., Methods: Atomic absorption spectroscopy (AAS) was used to characterize the chemical interaction. Micro-tensile bond strength (μTBS) and fractographic analyses were performed after 24h and one year. Confocal micro-permeability and SEM nanoleakage assessments were also undertaken. The tested functional monomers were 2-MEP (2-carbon spacer), 10-MDP (10-carbon), 12-MDDP (12-carbon), MTEP (high hydrophilic polyether spacer chain) and CAP-P (intermediate hydrophilic ester spacer)., Results: AAS revealed clear differences (p<0.05) in monomer-calcium salt formation in this order: 12-MDDP=10-MDP>CAP-P>MTEP>2-MEP. The highest initial dentin μTBS was obtained using 10-MDP or 12-MDDP. After 1-year aging, a significant drop (p<0.05) in μTBS was observed for the adhesives with MTEP (enamel and dentin), 2-MEP (enamel) and CAP-P (enamel). MTEP presented the highest micro-permeability, while 2-MEP, CAP-P and MTEP showed increased nanoleakage after aging., Significance: These outcomes showed that more hydrophilic and shorter spacer chains may compromise the chemical interaction with calcium and the dentin/enamel bonding performance., (Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.)

Objective: To evaluate quantitatively the marginal microleakage of restorations carried out with self-etching adhesives with or without prior phosphoric enamel acid etching of silorane or methacrylate resin-based composite restorations subjected to thermal cycling., Materials and Methods: Forty cavities were prepared at the proximal surface of bovine incisors and randomly divided according to the etching of the enamel and restorative system used. The groups were restored with methacrylate [Adper SE Plus adhesive (3M ESPE) + Filtek Z250 (3M ESPE)] or silorane [Filtek LS adhesive (3M ESPE) + Filtek LS composite (3M ESPE)] restorative systems, light-cured using a LED unit (Bluephase 16i, Vivadent). After restorative procedure and thermocycling (1000 cycles), the specimens were immersed in methylene blue for 2 h. The specimens were triturated and the powder was used for analysis in an absorbance spectrophotometer. Data were statistically analyzed by 2-way ANOVA (alpha = 0.05)., Results: No statistical difference between the restorative materials tested with or without previous acid etching of enamel in Class II marginal microleakage was observed (p > 0.05)., Conclusions: The use of acid etching prior to self-etching adhesives did not interfere on the microleakage of methacrylate- or silorane-based restorations.

Purpose: Evaluate cuspal flexure caused by polymerization shrinkage stress, bond integrity, and depth-of-cure of bulk-fill composites., Methods: Twenty-eight extracted permanent molars were mounted in stainless steel rings. Slot-shaped Class II mesio-occlusal-distal preparations (four mm deep) were restored with Filtek Supreme Ultra (control; two two-mm increments) and bulk-fill composites (Tetric EvoCeram, Venus, Filtek Bulk Fill). The teeth were digitized using a 3D scanner before and after restoration. Before- and after-restoration scans were aligned, and cuspal flexure was calculated. Bond integrity along occlusal interfaces was assessed by dye penetration and measured after overnight immersion in basic fuchsin dye and cross-sectioning. Depth-of-cure was determined on the cross-sections using Vickers hardness. Statistical analysis was performed with one-way analysis of variance., Results: All composites caused inward cuspal flexure (10.4 to 13.6 μm). No statistical difference in flexure was found among the composites (P=.07). No significant difference in microhardness at any restoration depths was found for any composite (.35

Objective: To assess the sealing ability of ProRoot MTA when placed as an apical barrier using three different techniques., Method and Materials: Sixty freshly extracted single-rooted human teeth were decoronated and standardized to a root length of 15 mm. The root segments were prepared with Gates Glidden burs to simulate a divergent open apex of immature teeth and randomly assigned into three experimental groups of 20 samples each. MTA (5 mm) was placed by pluggers (Group A), paper points (Group B), or ultrasonic tips (Group C). A cotton pellet moistened with saline was placed in the root canals till the material set, and the coronal portion was sealed with Cavit. After 24 hours, the Cavit and cotton pellet were removed and the canals dried and obturated with warm guttapercha (Obtura) and AH 26 sealer. Coronal portions of all samples were then sealed with Cavit. All root segments were double-coated with nail varnish except for the open apex and were exposed to methylene blue dye for 48 hours at room temperature. The samples were sectioned longitudinally (layer thickness 0.4 mm) and the extent of dye penetration was measured with a stereomicroscope (magnification 20×)., Results: The mean depth (± standard deviation) of dye leakage for Group A was 1.34 ± 0.5 mm, Group B 1.25 ± 0.4 mm, and Group C 1.14 ± 0.4 mm. There were no significant differences among the three experimental groups (.178 < P < .552)., Conclusion: ProRoot MTA has a similar sealing ability when placed as an apical barrier with pluggers, paper points, or ultrasonic tips.

Aim: To assess the influence of dentin substrate and chlorhexidine on the marginal seal of composite resin restorations., Materials and Methods: The sample comprised 20 third molars. Four cavities were drilled in the dentin sur face, followed by sealing and restoration of sound dentin (n = 10) or carious dentin (n = 10). In the control group, cavities were immediately restored as follows: G1: one-bottle bonding agent (OB) + composite resin (CR); G2: chlorhexidine 2.0% (CLX) + OB + CR; G3: self-etch bonding agent (SE) + CR; G4: CLX + SE + CR. In the experimental group (carious dentin), carious lesions were induced with S. mutans and cavities were restored as in the control group. Five specimens from each group (sound and carious) were stored in brain-heart infusion (BHI) medium for 6 months. All specimens were submerged in methylene blue 0.5% to test for microleakage. The Kruskal-Wallis and Student-Newman-Keuls tests were used to assess results., Results: On immediate assessment, there were no significant between-group differences in the sound dentin group, whereas in carious dentin, there was less leakage when OB and CLX were used. At 6 months, there was less leakage in the sound dentin group when OB and CLX were used; there were no between-group differences in carious dentin. Comparison of immediate and 6-month assessments showed a significant increase in leakage at 6 months when sound dentin was treated with SE and CLX and when carious dentin was treated with OB and CLX., Conclusion: To ensure better dentin hybridization and preservation of the organic constituents of the dentin matrix, the properties of chlorhexidine digluconate and the components of the resin matrix must be taken into account., Clinical Significance: Metalloproteinases influence degradation of the hybrid layer in composite resin restorations, regardless of whether the bonding system used is one-bottle or self-etching.

Aim: The aim of this in vitro study was to evaluate the effectiveness of a resin infiltrant (ICON) on marginal sealing ability of class II resin restorations with/without-caries., Materials and Methods: Forty-eight noncarious human pre-molar teeth were embedded and MO and DO preparations of standard dimensions were prepared. The left side of dentin margins of the cavities were left nonbonded (UB) while the right side were bonded using total etch-bonding agent and all restored with a Nanohybrid composite. The teeth were thermocycled and half of the specimens in the UB and B groups were subjected to an artificial caries process. ICON was applied to caries and noncaries subgroups following the manufacturer's directions. Impressions were made at each step: after the restorations were completed, thermocycling, artificial caries procedures, and infiltrant application and the silicone tag lengths were measured with a stereomicroscope. The specimens were immersed in 0.5% basic fuchsine at 37° C for 24 hours, sectioned and microleakage was evaluated with a stereomicroscope. Selected samples and their replicas were assessed for marginal quality under a stereomicroscope and SEM. Statistical evaluation of the data were made using Kruskal-Wallis, Mann-Whitney U and Wilcoxon Sign Rank tests., Results: While bonding application did not create a meaningful difference, the thermocycling and artificial caries significantly increased the gap length and microleakage (p < 0.05). ICON application was decreased the microleakage, created gap-free margins and closed the gaps which were previously occurred at the same cavities (p < 0.05)., Conclusion: A resin infiltrant (ICON) application decreased the microleakage, created gap-free margins and closed the gaps, which previously occurred at the same cavities., Clinical Significance: Approximal application of resin infiltrant may increase the success of the class II composite restorations also reduced the risk of needing more complex restoration therapy.

Aim: To quantify the microleakage on restorations carried out with a two-step etch-and-rise adhesive system and nanofilled composite resin after thermal and mechanical loading cycling., Methods: Ninety cavities were prepared on proximal surfaces of incisive teeth, and were randomly divided according to the photoactivation time (10, 20, or 30 s) and light-curing mode (Quartz Tungsten Halogen (QTH) lamps, 450 mW/cm(2); Light Emitting Diode (LED) second generation, 1100 mW/cm(2); or LED third generation, 700 mW/cm(2)) of an adhesive system (n = 10). Following restorative procedures and thermal and mechanical loading cycling, the samples were immersed in Methylene Blue for 2 h. The samples were ground, and the powder was prepared for analysis in an absorbance spectrophotometer. All results were statistically analyzed by anova and Tukey's test at the 5% level of significance., Results: There were no significant statistical difference in microleakage between the light-curing mode (P = 0.1212) and light-curing time (P = 0.2043)., Conclusion: Different curing modes and increasing the curing time were not factors that influenced the process of microleakage., (© 2013 Wiley Publishing Asia Pty Ltd.)

Aim: The aim of the present study was to evaluate the microleakage in class II cavities restored with dental composite by varying the thickness of two flowable composite resins and the restorative technique., Methods: A total of 130 cavities were prepared on proximal surfaces of bovine teeth and randomly divided in 13 groups. Twelve experimental groups were performed using flowable composite resin as the liner, and they were divided according to the type of flowable composite resin (Filtek Z350 Flow-Z350F and SureFil SDR Flow-SUR), the thickness of the flowable composite (0.5, 1, or 2 mm), and the restorative technique (flowable composite applied at the cavosurface angle or amelodentinal junction) (n = 10). A control group was performed without using a flowable composite. Following restorative procedures and thermocycling, the samples were immersed in Methylene Blue for 2 h, and prepared for analysis in an absorbance spectrophotometer. All results were statistically analyzed (α = 0.05)., Results: There was no significant difference between the flowable composites (P > 0.05). The restorative techniques influenced microleakage and were flowable composite dependent (P ≤ 0.05). The lower thickness of the flowable composite provided less microleakage (P ≤ 0.05)., Conclusion: The use a lower thickness of a flowable composite resin provided less microleakage, suggesting a better sealing tooth-restoration interface., (© 2013 Wiley Publishing Asia Pty Ltd.)

Purpose: The purpose of this study was to compare the differences in surface characteristics and roughness of teeth finished for porcelain veneer laminates using different instrumentation and to assess their influence on microleakage., Materials and Methods: Fifty-six extracted human maxillary central incisors were divided randomly into two groups: Group HsR teeth were finished with a high-speed handpiece with diamond burs; group SO teeth were finished with a sonic oscillating diamond instrument. Porcelain veneers were bonded to 24 teeth in each group. Microleakage was measured in the cervical area. Four remaining teeth in each group were examined using confocal laser-scanning microscopy and scanning electron microscopy., Results: Oscillating instruments produced a rougher dentinal surface (Ra values; P = .029) than those finished with high-speed rotary technology., Conclusions: There is less microleakage when bonded restoration edges are situated over dentin that has been finished with sonic oscillating instrumentation (P = .006).

Objectives: Selective caries removal involves sealing of carious dentine beneath restorations, which might decrease their marginal integrity and increase the susceptibility for secondary caries and microleakage. The present study compared these marginal characteristics of restorations in selectively and completely excavated teeth., Methods: In 32 premolars, shallow and deep artificial lesions were created on pulpo-axial walls of mesial-distal-occlusal cavities, with mesial and distal margins located in enamel and dentine, respectively. Demineralised dentine was either removed or left before adhesively restoring the teeth (n=8), which were then submitted to thermo-mechanical cycling. The integrity of gingivo-cervical margins was assessed using scanning electron microscopy. In half of each margin, caries was induced adjacent to restorations using a continuous-culture biofilm model, and resulting lesions were evaluated using transversal microradiography. The other half of each margin was used to assess microleakage., Results: Integrity or microleakage of margins located in enamel did not differ significantly between groups, and bacterial biofilms did not induce distinct caries lesions in enamel. Dentinal margins in teeth with deep compared with shallow lesions showed a significantly higher proportion of marginal imperfections, gaps and microleakage (p≤0.05, Mann-Whitney/χ(2)-test). In contrast, neither marginal integrity nor microleakage differed significantly between completely and selectively excavated teeth (p>0.05). Dentinal mineral loss adjacent to restorations did not differ significantly between groups (p>0.80)., Conclusions: The marginal characteristics of restorations were affected by the depth of sealed or excavated lesions, but not by the performed caries excavation. This study did not find selective excavation detrimental for restoration integrity in vitro., Clinical Significance: Selective excavation of deep lesions was shown to reduce pulpal risks, whilst leaving caries beneath restorations is feared to compromise the marginal characteristics of the subsequently placed restoration. Based on the present in vitro study, such assumptions cannot be supported., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

Purpose: To directly test the effectiveness of ethanol-wet bonding (EW) in improving monomer infiltration into demineralized dentin through quantitative measurement of bis-GMA and TEG-DMA molar concentrations within hybrid layers, and to comprehensively evaluate the effect of EW and chlorhexidine on durability of resin-dentin bonds compared to conventional water-wet bonding (WW)., Materials and Methods: A three-step etch-and-rinse adhesive (70% bis-GMA/28.75%TEG-DMA) was applied to coronal dentin using a clinically relevant ethanol-wet bonding protocol (EW) or the conventional water-wet bonding (WW) technique. Bis-GMA and TEG-DMA molar concentrations at various positions across the resin/dentin interfaces formed by EW and WW were measured using micro-Raman spectroscopy. The experiment was repeated at the same positions after 7-month storage in phosphate buffer solution containing 0.1% sodium azide. The μTBS and hybrid layer morphology (TEM) of bonding groups with and without chlorhexidine application were compared immediately and after 1-year storage in terms of nanoleakage, collagen fibril diameter, collagen interfibrillar width, and hybrid layer thickness., Results: Specimens bonded with EW showed significantly higher monomer molar concentrations and μTBS throughout the hybrid layer immediately and after storage, providing direct evidence of superior infiltration of hydrophobic monomers in EW compared to WW. Microscopically, EW maintained interfibrillar width and hybrid layer thickness for resin infiltration and retention. The application of chlorhexidine further preserved collagen integrity and limited the degree of nanoleakage in EW after 1-year storage., Conclusion: EW enhances infiltration of hydrophobic monomers into demineralized dentin. The results suggest that a more durable resin-dentin bond may be achieved with combined usage of a clinically relevant EW and chlorhexidine.

Purpose: The purpose of this study was to evaluate the influence of prior etching on the sealing of silorane composite restorations in Class V cavity preparations prepared with an Er,Cr:YSGG laser compared to bur preparation in primary teeth., Methods: Standard Class V cavity preparations were prepared on the buccal surfaces of 56 extracted primary canines and randomly divided into four groups of 14 teeth each, according to laser or bur preparation and the use of prior acid etching in the preparation. All cavity preparations were restored with silorane adhesive and silorane composite. After water storage and thermocycling, the specimens were placed in 0.5 percent basic fuchsin dye solution. Dye penetration was evaluated with a stereomicroscope. The data were analyzed with nonparametric tests (P=.05)., Results: Laser preparation and prior etching in bur-prepared cavity preparation had no significant effect on enamel sealing (P>.05), but significantly increased microleakage at the dentin margin (P<.001 and P=.001, respectively). Prior etching in laser-prepared cavity preparations significantly improved sealing at the enamel and dentin margins (P=.009 and P=.003, respectively)., Conclusions: Prior acid etching may be necessary to ensure good marginal sealing when laser preparation is used. However, this step is not required when bur cutting is used in primary teeth.

Aim: The aim was to determine the effect of four different intracanal medicaments on the apical seal of the root canal system in vitro., Methodology: Fifty freshly extracted intact human permanent maxillary central incisors were collected, stored and disinfected. The root canals were prepared to a master apical size of number 50 using step back technique. Depending upon the intracanal medicament used, the teeth were divided randomly into five groups of 10 teeth each including one control group and four experimental groups. Group A: No intracanal medicament. Group B: Calcium hydroxide powder mixed with distilled water. Group C: Calcium hydroxide gutta percha points (calcium hydroxide points). Group D: 1% chlorhexidine gel (hexigel). Group E: Chlorhexidine gutta percha points (Roeko Activ Points). The medication was left in canals for 14 days. Following removal of the intracanal medicament, all the groups were obturated with lateral compaction technique. The apical leakage was then evaluated using dye extraction method with the help of a spectrophotometer., Results: RESULTS were statistically analyzed using Kruskal-Wallis and Mann-Whitney U-test, which showed statistically significant difference among the five groups tested., Conclusion: It can be concluded from this study that the control group showed least amount of leakage, whereas the 1% chlorhexidine gel group showed maximum amount of leakage. Apical leakage was observed with all the experimental groups with little variations in between them. Under the parameters of this study, it can be concluded that use of intracanal medicaments during endodontic treatment has a definite impact on the apical seal of the root canal system.