Search

Purpose: The aim of this study was to compare the bone stress generated by rehabilitation using regular and short-length Morse taper implants (11 and 5 mm, respectively) in the same context and allied with splinted (SP) and nonsplinted (NSP) prostheses in the posterior area of the mandible using finite element analysis. Materials and Methods: Three-dimensional geometric models using regular implants (∅4 × 11 mm) and short implants (∅4 × 5 mm) were simulated with a left posterior mandible that had the first premolar tooth and all teeth posterior to that premolar removed. The four experimental groups were as follows: Group 1 NSP (two regular implants and one short implant rehabilitated with nonsplinted prostheses), Group 1 SP (two regular implants and one short implant rehabilitated with splinted prostheses), Group 2 NSP (one regular implant and two short implants rehabilitated with nonsplinted prostheses), and Group 2 SP (one regular implant and two short implants rehabilitated with splinted prostheses). Oblique forces were simulated in molars (365 N) and premolars (200 N). Qualitative and quantitative analyses of the minimum principal stress in bone were performed using the ANSYS Workbench software, version 10.0. Results: The splinted prostheses decreased the stress to the surrounding bone of short implants. Moreover, they also decreased the stress on the surrounding bone adjacent to the tooth. However, the splinted prostheses generated higher stress in the coverage of the surrounding bone for regular intermediate implants and prominently in the bone at the implant cervical region, at the edge crest, compared with the individualized groups. Conclusion: The benefits in the use of splinted prostheses are notable for the preservation of the bone surrounding the short implants and tooth; however, it is necessary to evaluate each clinical situation because, in this context, the regular implants are at higher stress than the individualized implants.

This study used finite element analysis to compare the biomechanical performance of splinted (SP) and nonsplinted (NSP) prostheses to regular and short length Morse taper implants in the posterior side of the mandible.The authors used 3-dimensional geometric models of regular implants (∅4 × 11 mm) and short implants (∅4 × 5 mm) housed in the corresponding bone edges of the posterior left mandibular hemiarch involving tooth 34. The 8 experimental groups were: the control group SP (3 regular implants rehabilitated with SP), group 1SP (2 regular and 1 short implants rehabilitated with SP), group 2SP (1 regular and 2 short implants rehabilitated with SP), group 3SP (3 short implants rehabilitated with SP), the control group NSP (3 regular implants rehabilitated with NSP), group 1NSP (2 and 1 short implants rehabilitated with NSP), group 2NSP (1 regular and 2 short implants rehabilitated with NSP), and group 3NSP (3 short implants rehabilitated with NSP). Oblique forces were simulated in the molars (365 N) and premolars (200 N). Qualitative and quantitative analysis of the distribution of Von Mises equivalent stress (implants, components, and infrastructure) was performed using the AnsysWorkbench10.0 software.The results showed that the use of SP provides several advantages and benefits, reducing the stresses placed on the implant surface, on the transmucosal abutment areas and on the interior region of the infrastructure. The use of NSP was advantageous in reducing the stresses on the abutments and in the distal interproximal area of connection between the crowns.

To evaluate the effect of thermal cycling and inner surface treatment with aluminum oxide at different granulations on the tensile strength of Ni-Cr copings cemented with different cementing agents.Ninety-six metal copings were manufactured and divided into two groups: before and after thermal cycling (n = 48). The copings of both groups were internally treated by sandblasting with aluminum oxide particles of 100 (n = 24) and 320 (n = 24) mesh. The copings were cemented on previously manufactured metal cores using zinc phosphate (n = 8), conventional glass ionomer (CGIC) (n = 8) and resin-modified glass ionomer (RMGIC) (n = 8) cements. The tensile strength before and after thermal cycling was then determined (Newtons).The tensile strength before and after thermal cycling was significantly higher in copings cemented with RMGIC compared to CGIC (p0.05) and was similar to that for zinc phosphate (p0.05). Thermal cycling and sandblasting of the inner surface of the metal copings with different granulations did not influence retention (p0.05).Zinc phosphate cements and RMGIC showed similar retention. Additionally, the retention of the cements was not influenced by either thermal cycling or the particle size of the aluminum oxide.

Purpose To compare the stress distribution of mandibular full dentures supported with implants according to the bar materials and manufacturing techniques using a qualitative photoelastic analysis. Material and methods An acrylic master model simulating the mandibular arch was fabricated with four Morse taper implant analogs of 4.5 × 6 mm. Four different bars were manufactured according to different material and techniques: fiber-reinforced resin (G1, Trinia, CAD/CAM), commercially pure titanium (G2, cpTi, CAD/CAM), cobalt‑chromium (G3, Co-Cr, CAD/CAM) and cobalt‑chromium (G4, Co-Cr, conventional cast). Standard clinical and laboratory procedures were used by an experienced dental technician to fabricate 4 mandibular implant-supported dentures. The photoelastic model was created based on the acrylic master model. A load simulation (150 N) was performed in total occlusion against the antagonist. Results Dentures with fiber-reinforced resin bar (G1) exhibited better stress distribution. Dentures with machined Co-Cr bar (G3) exhibited the worst standard of stress distribution, with an overload on the distal part of the posteriors implants, followed by dentures with cast Co-Cr bar (G4) and machined cpTi bar (G2). Conclusion The fiber-reinforced resin bar exhibited an adequate stress distribution and can serve as a viable alternative for oral rehabilitation with mandibular full dentures supported with implants. Moreover, the use of the G1 group offered advantages including reduced weight and less possible overload to the implants components, leading to the preservation of the support structure.

Context: The pulse oximeter is a device that noninvasively provides continuous information about the peripheral oxygen saturation (SpO2) rate. This device is utilized in the detection of hypoxemia, due to its able to sense changes in hemoglobin oxygen saturation. Aims: The objective of this study was to verify the accuracy of the Choice® Medical MD300C3 Fingertip Pulse Oximeter, as compared to that of a hospital oximeter coupled with a Dräger® Infinity Delta monitor, with the purpose of using this first methodology in dental procedures to monitor the peripheral oxygen saturation (SpO2) of patients submitted to dental treatments. Materials and Methods: Fifty-five adult patients, both genders, were selected in the Santa Casa Hospital of Maringa, Brazil. The volunteers did not present cardiac problems, prosthetic cardiac valves, pacemakers, or pulmonary diseases, and were not pregnant or children. Each patient received a portable fingertip pulse oximeter (PPO) on the middle finger of the left hand and the hospital oximeter (control device) on the forefinger of the same hand. A total of six measurements were developed. The Pearson correlation coefficient and the Bland and Altman method was used to calculate the statistical analysis. Results: No statistically significant difference was found between the measurements taken by the utilized devices. The average of comparative analysis presented by the devices was 0.2337 ± 0.4355 (mean ± SD), suggesting a strong correlation between the obtained results. Conclusion: According to the methodology of the research, the PPO has similar accuracy to the conventional hospital oximeter with digital sensor. The PPO can be used in dental treatments.