Search

The use of microfluidic fuel cells (μFCs) as power sources in the development of non-implantable biomedical devices, such as patch sensors, could be broadened with the use of physiological fluids as fuels and the use of low-cost materials. In this work, we report the evaluation of a paper-based photo-μFC working with human blood as fuel, and we implement a nanocomposite as anode that presents photoactivity under visible light. The electrocatalyst was synthesized using Zn(NO3)2 and TiCl4 as precursors of the ZnO and the TiO2, respectively, which were coated with Au nanoparticles. It was demonstrated that ZnO and TiO2 nanoparticles consisted of crystals with wurtzite and anatase phases, with average sizes of 26.6 and 19.5 nm, respectively, and the TiO2/ZnO/Au nanocomposite presents 2.62 eV of band gap energy, demonstrating its photoactivity under visible light irradiation. The photocatalyst was tested as photoanode in half-cell for glucose oxidation in aqueous solutions, under illumination and dark conditions, showing characteristics peaks of glucose oxidation in both cases, but higher current was generated under illumination. Finally, we present the implementation of this anode and the construction of a paper-based photo-μFC using human blood as fuel; its performance was evaluated under visible light irradiations and in the dark. The results show a better performance under illumination with voltage, current, and power density values of 0.95 V, 1.2 mA cm−2, and 0.458 mW/cm2, respectively, compared to the corresponding values of 0.8 V, 0.96 mA cm−2, and 0.274 mW/cm2 in dark conditions. [ABSTRACT FROM AUTHOR]

The direct integration of paper-based microfluidic fuel cells (μFC's) toward creating autonomous lateral flow assays has attracted attention. Here, we show that an air-breathing paper-based μFC could be used as a power supply in pregnancy tests by oxidizing the human urine used for the diagnosis. We present an air-breathing paper-based μFC connected to a pregnancy test, and for the first time, as far as we know, it is powered by human urine without needing any external electrolyte. It uses TiO 2 -Ni as anode and Pt/C as cathode; the performance shows a maximum value of voltage and current and power densities of ∼0.96 V, 1.00 mA cm − 2 , and 0.23 mW cm − 2 , respectively. Furthermore, we present a simple design of a paper-based μFC's stack powered with urine that shows a maximum voltage and maximum current and power densities of ∼1.89 V, 2.77 mA cm − 2 and 1.38 mW cm − 2 , respectively, which powers the display of a pregnancy test allowing to see the analysis results. [ABSTRACT FROM AUTHOR]

The research aims were to construct an air-breathing paper-based microfluidic fuel cell (paper-based μ FC) and to evaluated it with different soft drinks to provide energy for their prospective use in portable devices as an emergency power source. First, in a half-cell configuration, cyclic voltammetry showed that glucose, maltose, and fructose had specific oxidation zones in the presence of platinum-ruthenium on carbon (PtRu/C) when they were individual. Still, when they were mixed, glucose was observed to be oxidized to a greater extent than fructose and maltose. After, when a paper-based μ FC was constructed, PtRu/C and platinum on carbon (Pt/C) were used as anode and cathode, the performance of this μ FC was mostly influenced by the concentration of glucose present in each soft drink, obtaining maximum power densities at room temperature of 0.061, 0.063, 0.060, and 0.073 mW cm − 2 for Coca Cola ® , Pepsi ® , Dr. Pepper ® , and 7up ® , respectively. Interestingly, when the soft drinks were cooled, the performance was increased up to 85%. Furthermore, a four-cell stack μ FC was constructed to demonstrate its usefulness as a possible power supply, obtaining a power density of 0.4 mW cm − 2 , using Coca Cola ® as fuel and air as oxidant. Together, the results of the present study indicate an alternative application of an μ FC using soft drinks as a backup source of energy in emergencies. [ABSTRACT FROM AUTHOR]