Search

In this work a new expansion measurement methodology for the detection of ageing mechanisms in lithium ion cells is described and evaluated. For this purpose, a polarization-optical homodyne Michelson interferometer with a resolution of approx. 10 nm was set up to allow measurements of different cell types, cell sizes, and cell chemistry within a Memmert IP55 climate chamber. The used interferometric measurement setup is ten times more accurate than measurement systems commonly used for battery measurements in the literature. The better spatial resolution of an interferometer setup enables the recording of the expansion response to short current pulses with low transferred charge. This offers the possibility to detect ageing mechanisms such as lithium plating within short measuring times. With this measurement setup, a lithium iron phosphate pouch cell from the company A123, with the model identification AMP20M1HD-A, is measured. First, an expansion measurement over a full charge and discharge cycle with a constant load of $\pm \frac {C}{20} (\widehat {=} {\mathrm {1\,\, \text {A}}})$ is performed. Here, the cell undergoes an expansion of about $\mathrm {42 ~\mu \text { m} }$ . Subsequently, the in this work proposed measurement methodology is presented to show the influence of effects such as the formation of overshooting graphite stages or lithium plating on cell expansion. For this purpose, at a residual capacitance of 50%, the cell is pulsed with current of different intensity $I \in \{\pm {\mathrm {20 \text {A}}}, \pm {\mathrm {80 \text {A}}}\}$ for $t = \{ {\mathrm {240\,\, \text {s}}}, {\mathrm {60\,\, \text {s}}}\}$ , at $T = \{ { {10\,\, ^{\circ}\text{C}}}, { {20\,\, ^{\circ}\text{C}}}, { {30\,\, ^{\circ}\text{C}}}\}$ , respectively, and the mechanical response is recorded using the high accuracy interferometer setup. A mechanical relaxation of the cell after the pulses with a time constant in the range between 10 s and 20 s can be observed. It is shown that this relaxation behavior can be associated with effects of the anode known from the literature, such as the formation of overshooting graphite stages or lithium plating. These effects can be recorded by the very high-resolution measurement already with little transferred charge and within a short measurement time.

In this work, an experimental approach to reduce the variation from cell to cell during battery operation is evaluated to reach a better battery utilization. Numerous theoretical considerations of intelligent battery management systems without long-term experimental validation of their capabilities lead to a gap in the literature, which this work aims to address. For this purpose, the ageing behaviour of two batteries is investigated for almost 1.5 years. One battery is connected to an active balancing battery management system (BMS) and the other to a conventional passive balancing BMS. Important battery parameters, such as capacity and internal resistance, are recorded in each cycle. The battery behaviour is evaluated in detail by observing the voltage difference of the individual cells at the end of discharge and by calculating the amount of charge balanced by the BMS. Significant differences between the BMS systems used are elucidated, which illustrate the advantages of active balancing. In contrast to passive balancing, active balancing can reduce the ageing rate of the battery and achieve better utilization with a more than five times lower voltage spread at end of discharge, a up to 3.1% higher discharge capacity and a 7.7% longer service life.

In this work, a battery consisting of eight commercial NMC/graphite cells connected in series was cycled to 60% of its initial capacity. During the test, special care was taken to ensure that the results were not influenced by either the module assembly or the module design. For this purpose, the cells were virtually connected in a laboratory environment with the help of the test device as if they were operated together in a battery. Extrinsic influences that affect cell aging were thus reduced to a minimum. Differential Voltage Analysis (DVA), Electrochemical Impedance Spectrum (EIS), and relaxation measurements were performed to analyze the aging behavior of each cell. The results show that despite a theoretically perfect module design, Cell-to-Cell Variations (CtCV) occurred during aging. The shifting Depth of Discharge (DoD) values among the cells further amplify CtCV. Lithium plating was also observed in the faster aging cells after cyclic aging, suggesting that this aging effect contributes significantly to the development of CtCV. After the aging test, the battery was equipped with an active balancing system that maximizes capacity utilization. More important, the balancing charges which are calculated iteratively within the used balancing algorithm show a strong correlation to the pure capacity losses and thus provide a new way to determine the capacity values of each cell individually without disassembling the battery.

The aim of this work is to age commercial battery cells far beyond their expected lifetime. There is a gap in the literature regarding run to failure tests of lithium-ion batteries that this work intends to address. Therefore, twenty new Samsung ICR18650-26F cells were aged as a battery pack in a run to failure test. Aging took place with a constant load current and a constant charge current to accelerate capacity decrease. Important aging parameters such as capacity and internal resistance were measured at each cycle to monitor their development. The end of the test was initiated by the explosion of a single battery cell, after which the battery pack was disassembled and all parameters of the still intact single cells were measured. The distribution of all measured capacities and internal resistances is displayed graphically. This clearly shows the influence of the exploded cell on the cells in its immediate vicinity. Selected cells from this area of the battery were subjected to computed tomography (CT) to detect internal defects. The X-rays taken with computed tomography showed clear damage within the jelly roll, as well as the triggered safety mechanisms.