Search

Copyright of Polimery is the property of Industrial Chemistry Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Simulation codes currently used in the foundry industry are primarily used to predict casting quality, quality tied mainly to the location of defects such as shrinkage (voids of shrinkage origin). The effective use of the simulation system requires identification and knowledge of, adapted to the reality, physical parameters (thermal) of the casting - mould system. The lack of as complete as a possible identification of these values, used in modelling dependencies, is the cause of limitation of the development and scope of models describing casting solidification. The development condition of the simulation code in the foundry practice is the correct model installation and the use of the database corresponding to the model. The following application presents the analysis of the impact of simulation parameters on the prediction of the casting defects.

The article presents results on the decomposition of polylactic acid (PLA)/halloysite nanotube (HNT) biocomposites. Experiments were carried out in laboratory conditions simulating composting in the industrial pile using the so-called short degradation method. In this paper, the effects of the composting process (duration from 30 to 90 days) on the behavior of PLA/HNT composites were studied. In addition, the selected physicochemical properties of PLA/HNTs biocomposites such as the average molecular weight were investigated. The results obtained confirmed the viability of composting PLA with halloysite which contributes to the reduction of plastic waste and the use of this material in technological applications.

Plastics recycling has become a key industry in developed countries, to reduce ecological damage and save non-renewable resources. This paper discusses the concept and the design of electrostatic separator as a test bench for the separation of different plastics in recycling applications. In the automotive recycling process, all these waste materials must be processed further for re-entering the cycle or thermal utilization. The following application presents the possibility of research and technological tests by changing several parameters, such as a position of the electrodes, control of the polarity and voltage, variable speed of feeder and drum, and also tribo-electrification parameters (time, intensity). The impact of process parameters on the efficiency of the plastic separation can be analyzed by the developed a specialized computer vision system. The preliminary results of conducted tests showed that separation is dependent on many variations of parameters. The results of this study indicate that the proposed innovative design of the research stand ensures the high research potential of the proposed equipment.

Aluminum metal matrix composites (Al MMCs) are a class of materials characterized by being light in weight and high hardness. Due to these properties, Al MMCs have various applications in the automobile, aeronautical and marine industries. Ceramic-reinforced Al MMCs in the form of sinters are known for having excellent abrasive properties, which makes them an attractive material in certain fields of technology. The biggest problem in their production process is their low ability to infiltrate ceramics with alloys and consequently the difficulty of filling a ceramic preform. The castability of such composites has not yet been researched in detail. The aim of this study was to create aluminum metal matrix composite castings based on aluminum alloys (AlSi11) reinforced with an Al2O3 sinter preform using a Castability Trials spiral mold, and then to determine the degree of saturation with the liquid metal of the produced ceramic shaped body (Castability Trials spiral). For the selected AlSi11 alloy, the liquidus (Tl) and solidus (Ts) temperatures were determined by performing thermal-derivation analysis during cooling, which is Tl—579.3 °C and Ts—573.9 °C. The resultant pressure necessary for the infiltration process was estimated for the reinforcement capillaries with the following dimensions: 10, 15, 20, 25, 30 and 35 microns. The following values were used to determine the capillary pressure (Pk): surface tension of the alloy—σ = 840 mN/m; the extreme wetting angle of the reinforcement by the metal—θ = 136°. It has been experimentally confirmed that for the vacuum saturation process, the estimated resultant pressure enables saturation of reinforcement with capillaries larger than 25 microns, provided that the alloy temperature does not drop lower than the infiltration temperature. After the experiment, the time and route of the liquid metal flow in the spiral were determined. On the basis of the obtained values, a simulation was developed and initial assumptions such as saturation time, alloy temperature, reinforcement and mold temperature were verified. The energy balance showed that the saturation limit temperature was Tk = 580.7 °C for the reinforcement temperature of 575 °C. In contrast to the above, the assumption that the temperature of the metal after equalizing the temperature of the composite components must be higher than the liquidus temperature (Tliq = 579.3 °C) for the aluminum alloy used must be fulfilled. After the experiment, the time and path of the liquid metal flow in the spiral were determined. Then, on the basis of the obtained values, a simulation was developed, and the initial assumptions (saturation time and temperature) were verified. [ABSTRACT FROM AUTHOR]

The article presents the results of the research related to the decomposition of polylactic acid (PLA)/halloysite nanotube (HNTs) biocomposites into a simple organic form. After manufacturing the nanocomposites, the evaluation of the composting process simulation was conducted using the biodegradation method. First, the selected properties of PLA/HNTs biocomposites, such as density, water absorption, and impact strength were tested. Next, the impact of the composting process on the behavior of PLA/HNTs composites was investigated from 30 to 90 days. Finally, the loss of mass of the composites, hardness, and the structural changes of biocomposites under the composting conditions before and after the composting were evaluated using SEM microscopy. The results showed that the PLA modified by HNT particles has biodegradation-friendly properties and therein is fully suitable for organic recycling. Due to this, in the coming years, it may contribute to the replacement of non-biodegradability polymers, i.e. polyolefins and polyesters, and reduction of plastic packaging wastes. [ABSTRACT FROM AUTHOR]

Many researchers in the developed countries have been intensively seeking effective methods of plastic recycling over the past years. Those techniques are necessary to protect our natural environment and save non-renewable resources. This paper presents the concept of an electrostatic separator designed as a test bench dedicated to the separation of mixed plastic waste from the automotive industry. According to the current policy of the European Union on the recycling process of the automotive industry, all these waste materials must be recycled further for re-entering into the life cycle (according to the circular economy). In this paper, the proposed concept and design of the test bench were offered the feasibility to conduct research and technological tests of the electrostatic separation process of mixed plastics. The designed test bench facilitated assessing the impact of positions of high-voltage electrodes, the value and polarity of the high voltage, the variable speed of feeders and drums, and also triboelectrification parameters (like time and intensity) on the process, among others. A specialized computer vision system has been proposed and developed to enable quick and reliable evaluation of the impact of process parameters on the efficiency of electrostatic separation. The preliminary results of the conducted tests indicated that the proposed innovative design of the research stand ensures high research potential, thanks to the high accuracy of mixed plastics in a short time. The results showed the significant impact of the corona electrode position and the value of the applied voltage on the separation process effectiveness. It can be concluded that the results confirmed the ability to determine optimally the values of the studied parameters, in terms of plastic separation effectiveness. This study showed that this concept of an electrostatic separator designed as a test bench dedicated for separation of mixed plastic waste can be widely applied in the recycling plastic industry. [ABSTRACT FROM AUTHOR]

Copyright of Polimery is the property of Industrial Chemistry Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Polimery is the property of Industrial Chemistry Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this paper, the influence of bentonite (BNT) on rheological properties, linear shrinkage, hardness, and structure of polyethylene wax (PE-wax) used in the lost-wax casting process are studied. Experiments were conducted with PE-wax with different contents of bentonite (from 0.1 to 5 wt.%). The structural changes of modified polyethylene wax were evaluated using differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The addition of bentonite in a concentration range between 0 and 0.8 wt.% into PE-wax caused a decrease of the linear shrinkage and the hardness of PE-wax/BNT blends. Modified polyethylene wax containing greater than 1 wt.% of the filler showed an increase in viscosity. The DSC-based investigations confirmed good miscibility and a uniform structure of PE-wax with BNT. Moreover, an increase in melting temperature onset and its enthalpy observed for filler PE-wax material showed an influence of bentonite on the crystalline structure of the polymeric matrix. SEM observations of the fractured surfaces confirmed the homogeneous structure of blends with contents up to 0.8 wt.% BNT. In the case of higher filler concentrations, the presence of more numerous and large clusters of filler in the polymer matrix was observed due to the increase in the viscosity of the PE-wax/BNT melt composition during mixing. The PE-wax blend with 0.4 wt.% BNT gives better results of reduced linear shrinkage and lower hardness than unmodified material. Lastly, a new developed material (PE-wax/0.4 BNT) was subjected to technological tests, consisting of the preparation of the mold and manufacture of a high-quality aluminum cast, using the lost-wax method.