Search

As a main functional component of rock sheds in rockfall protection projects, traditional sand cushions have shortcomings such as heavy weight and weak buffering capacity. EPS bead-sand cushion can effectively solve these problems, but its buffering mechanism has not been fully revealed. In this study, a series of impact tests were carried out to investigate the performance of EPS bead-sand cushions with different EPS bead contents, and the evolutions of rockfall impact force, penetration depth, earth pressure, and slab vibration under single impact and multiple impacts were comparatively analyzed. The results show that with the addition of EPS beads, the maximum impact force, the peak earth pressure, and the vibration acceleration are significantly reduced. However, the cushion with high EPS bead content is at risk of being penetrated under high energy or multiple impacts, leading to excessive concentration of impact stresses. Furthermore, the EPS beads can alleviate the hardening of the sand cushion under impact through their deformation coordination, but excessive penetration should be prevented in the design of EPS bead-sand cushions. On this basis, combined with traditional sand cushion design theory, an estimation method for the maximum impact force applicable to EPS bead-sand cushion was proposed. The research results can provide a reference for the design and optimization of cushions in actual projects. [ABSTRACT FROM AUTHOR]

Background and Aims: Wheelchairs are a basic necessity for people with disabilities, especially people with physical disabilities. Although conventional wheelchairs have aided the mobility of people with disabilities, they are limited in scope due to physical exhaustion and health problems from sitting in wheelchairs for a long time. This research is important to develop seatback and cushion features for Health Electric Wheelchair Portable IoT-Based wheelchairs, for easy and comfortable mobility for people with disabilities. The development of wheelchairs aims to reduce the negative impact of prolonged immobilization on people with physical disabilities. Methods: Research & Development method. The development stage: 1). The development of pads for Health Electric Wheelchair Portable IoT-Based seatback and cushion needed by wheelchair users; 2). Development of expert-validated Health Electric Wheelchair Portable IoT-Based ergonomics and seatback in accordance with the needs of wheelchair users to improve physical independence; 3). Modify components and equipment for Health Electric Wheelchair Portable IoT-Based cushion and seatback. Results: The result of this development of this wheelchair pays attention to ergonomic design by developing seatback and chair features for Health Electric Wheelchair Portable IoT-Based wheelchairs to provide safety and comfort when using wheel-chairs, especially physical disability. Conclusion: The development of cushion and seatback on wheelchairs can reduce the negative impact of immobilization on people with physical disabilities and is able to provide broad access for users to mobilize on wheelchairs and can adjust to the ergonomics of each user's body. [ABSTRACT FROM AUTHOR]

Abstract As a main functional component of rock sheds in rockfall protection projects, traditional sand cushions have shortcomings such as heavy weight and weak buffering capacity. EPS bead-sand cushion can effectively solve these problems, but its buffering mechanism has not been fully revealed. In this study, a series of impact tests were carried out to investigate the performance of EPS bead-sand cushions with different EPS bead contents, and the evolutions of rockfall impact force, penetration depth, earth pressure, and slab vibration under single impact and multiple impacts were comparatively analyzed. The results show that with the addition of EPS beads, the maximum impact force, the peak earth pressure, and the vibration acceleration are significantly reduced. However, the cushion with high EPS bead content is at risk of being penetrated under high energy or multiple impacts, leading to excessive concentration of impact stresses. Furthermore, the EPS beads can alleviate the hardening of the sand cushion under impact through their deformation coordination, but excessive penetration should be prevented in the design of EPS bead-sand cushions. On this basis, combined with traditional sand cushion design theory, an estimation method for the maximum impact force applicable to EPS bead-sand cushion was proposed. The research results can provide a reference for the design and optimization of cushions in actual projects.

Pile-slab rockfall retaining wall is a novel passive protective structure designed to intercept falling rocks. It is made up of cantilever piles, pile-intermediate slabs, and cushion layers. This structure features strong terrain adaptability , small footprint, and high interception height, making it applicable in high-risk rockfall areas. However, due to the lack of detailed reports on the ultimate bearing capacity of cantilever piles, guidance for engineering practice is unavailable. This paper first proposes a reasonable thickness for the cushion layer based on the characteristics of the propagation of falling rock impact forces. Then, according to the stress and deformation characteristics of the pile body, theoretical calculation methods of the internal forces and displacements of the pile body are derived using the elastic support cantilever beam model and the Winkler elastic foundation beam model, enabling the automatic determination of design parameters for cantilever pile under falling rock impact. The results indicate that for a rockfall with a diameter of 2 m, impact height of 7.0 m, impact velocity of 10 m/s, and a cushion layer thickness of 1.5 times the rockfall diameter, a double-row triple-limb steel-reinforced 1.5 m × 1.2 m cantilever pile can withstand an impact force of 2.51 × 106 N and impact energy of 565 kJ. For cases with higher falling rock impact energy, it is recommended to prioritize enhancing the bending resistance of the retaining wall. This research provides a scientific basis for disaster prevention and reduction in rockfall-prone areas in the western mountainous regions of China.

Pile-slab rockfall retaining wall is a novel passive protective structure designed to intercept falling rocks. It is made up of cantilever piles, pile-intermediate slabs, and cushion layers. This structure features strong terrain adaptability, small footprint, and high interception height, making it applicable in high-risk rockfall areas. However, due to the lack of detailed reports on the ultimate bearing capacity of cantilever piles, guidance for engineering practice is unavailable. This paper first proposes a reasonable thickness for the cushion layer based on the characteristics of the propagation of falling rock impact forces. Then, according to the stress and deformation characteristics of the pile body, theoretical calculation methods of the internal forces and displacements of the pile body are derived using the elastic support cantilever beam model and the Winkler elastic foundation beam model, enabling the automatic determination of design parameters for cantilever pile under falling rock impact. The results indicate that for a rockfall with a diameter of 2 m, impact height of 7.0 m, impact velocity of 10 m/s, and a cushion layer thickness of 1.5 times the rockfall diameter, a double-row triple-limb steel-reinforced 1.5 m x 1.2 m cantilever pile can withstand an impact force of 2.51 x 106 N and impact energy of 565 kJ. For cases with higher falling rock impact energy, it is recommended to prioritize enhancing the bending resistance of the retaining wall. This research provides a scientific basis for disaster prevention and reduction in rockfall-prone areas in the western mountainous regions of China. [ABSTRACT FROM AUTHOR]

Copyright of Machine Tool & Hydraulics is the property of Guangzhou Mechanical Engineering Research Institute (GMERI) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

To describe the current seating recommendations made by a seating clinic for wheelchair users who presented with a Pressure Injury (PrI) or history of PrI. Retrospective review of electronic medical records of 133 adults who used a wheelchair as their primary means of mobility who had a cushion evaluation during which interface pressure mapping data was documented. Clinicians adjusted 71% of participants' wheelchair cushions, including 49% who received a new cushion, and 37% of participants' wheelchairs. The most common adjustments besides receiving a new cushion were: addition of an underlay, adjusting the inflation of a cushion, and adjustments to the foot or back support of the wheelchair. Forty-five participants only received adjustments (i.e. no new cushion), while 23 participants only received education and feedback rather than equipment modifications. Those 23 participants had significantly lower Peak Pressure Index (PPI) than those who received equipment modifications (mean [95% CI] 76.7 [59.1, 94.3] versus 111.6 [102.1, 121.2] respectively, p = 0.001). The PPI was reduced by an average of 22.5 mmHg from the initial to final seating system amongst those who received modifications ([13.9–31.0], p<.001). The seating clinicians considered interface pressure mapping in their decision-making and effectively reduced interface pressures with their interventions. Cushion replacement is important when someone presents with a PrI. However, adjusting an existing wheelchair cushion and/or seating system provides important additions and alternatives to consider for reducing interface pressure. There is also a role for education about proper use of equipment, weight shifts, and alternate seating surfaces. A cushion evaluation may involve evaluating more than one cushion configuration and using pressure mapping to compare the best options. To address perceived wheelchair cushion issues, posture and positioning should be evaluated and adjusted as necessary, in addition to evaluating the cushion itself. Common positioning modifications include: modifying/adding cushion underlays or inflation and foot and back supports in response to clients' changing postural needs and wheelchair components coming out of optimal position due to wear and tear. Adjustments to the wheelchair and cushion aim to distribute body weight over a larger surface area, reduce pressure at high-risk locations, improve posture, and increase function. These adjustments should consider individual's specific needs and goals, while also being mindful of funding barriers. [ABSTRACT FROM AUTHOR]

Background: The perception of tactile-stimulation locations is an important function of the human somatosensory system during body movements and its interactions with the surroundings. Previous psychophysical and neurophysiological studies have focused on spatial location perception of the upper body. In this study, we recorded single-trial electroencephalography (EEG) responses evoked by four vibrotactile stimulators placed on the buttocks and thighs while the human subject was sitting in a chair with a cushion. Methods: Briefly, 14 human subjects were instructed to sit in a chair for a duration of 1 h or 1 h and 45 min. Two types of cushions were tested with each subject: a foam cushion and an air-cell-based cushion dedicated for wheelchair users to alleviate tissue stress. Vibrotactile stimulations were applied to the sitting interface at the beginning and end of the sitting period. Somatosensory-evoked potentials were obtained using a 32-channel EEG. An artificial neural net was used to predict the tactile locations based on the evoked EEG power. Results: We found that single-trial beta (13–30 Hz) and gamma (30–50 Hz) waves can best predict the tactor locations with an accuracy of up to 65%. Female subjects showed the highest performances, while males' sensitivity tended to degrade after the sitting period. A three-way ANOVA analysis indicated that the air-cell cushion maintained location sensitivity better than the foam cushion. Conclusion: Our finding shows that tactile location information is encoded in EEG responses and provides insights on the fundamental mechanisms of the tactile system, as well as applications in brain–computer interfaces that rely on tactile stimulation. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Engineering (17264073) is the property of Republic of Iraq Ministry of Higher Education & Scientific Research (MOHESR) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Culverts are essential under earth embankments to allow watercourses, such as streams and nallas, to pass through without obstructing the natural flow. They help manage floodwaters on both sides of the embankment, reducing water levels and mitigating flood risks. Culverts come in various shapes, including arch, slab, and box configurations, and can be constructed from materials such as masonry or reinforced concrete. Culverts, embedded within earth embankments, are subjected to traffic loads similar to those on the road and must be designed to accommodate these loads. This paper focuses on the structural design and parametric analysis of RCC box culverts, both with and without cushion. Design parameters such as size, invert level, and layout are determined based on hydraulic considerations and site conditions, with the cushion depending on the road profile at the culvert location. The study examines various load cases (e.g., empty box, full box, surcharge loads) and factors such as effective width, braking force, load dispersion through fill, impact factor, and earth pressure coefficient as per IRC codes. It provides a comprehensive discussion on code provisions, design considerations, and justifications for the structural design of RCC box culverts, ensuring they can withstand maximum bending moments and shear forces. [ABSTRACT FROM AUTHOR]

The effect of geocell-reinforced cushion on load distribution and settlement reduction in unconnected piled raft foundations was investigated. Modeling and analysis of various scenarios were carried out using Abaqus software. In this research, a total of nine models, including one connected, three unconnected and unreinforced, and five unconnected and reinforced with geocell, were analyzed. Cushions with thicknesses half of, equal to, and twice that of the foundation were used. The results have shown that optimal outcomes in terms of load distribution efficiency and settlement reduction are achieved when the cushion's stiffness is set at half that of the foundation. The obtained results demonstrate the positive effect of geocell reinforcement in enhancing the performance of unconnected piled raft foundations. The introduction of geocells into the models increases soil stiffness and pile load ratio, consequently enhancing the load-bearing capacity of the piled raft foundation compared to the unreinforced models. The study's findings pave the way for a more effective use of geocells in civil engineering applications, particularly in scenarios demanding high load-bearing capacity and minimal foundation settlement.

Copyright of Firat University Journal of Experimental & Computational Engineering (FUJECE) is the property of Firat University Journal of Experimental & Computational Engineering (FUJECE) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Mycosystema is the property of Mycosystema Editorial Board and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The disconnected piled raft foundation (DCPRF) is one of the newly introduced foundations for specialization in geotechnical engineering, which significantly reduces the moment and stress on the pile head. In addition, this type of foundation is an ideal choice in areas with seismic activity due to the presence of cushion material between the raft and the piles. This work aims to present a numerical model in PLAXIS 3D software for connected piled raft and disconnected piled raft foundations under the influence of seismic loads and investigate the effect of pore water pressure on the disconnected foundation compared to the connected foundation. The study will depend on the earthquake that struck Iraq in November 2017 in the Halabja region. Strength was 7.3 on the Richter scale with PGA (0.1g). The results of changing pore water pressure showed the variation of pore water pressure. In the case of a DCPRF, the porewater pressure and excess porewater pressure in the soil are much greater than in the case of a CPRF. The increase in the porewater pressure is due to the weight of the building and the weight of the additional cushion layer on the soil. The mechanism for transferring the load in the case of a DCPRF is carried out by raft, then to the cushion, and then to the soil and piles. The load transferred to the soil in the case of DCPRF is more than that transferred to the soil in the CPRF system.

Background: The perception of tactile-stimulation locations is an important function of the human somatosensory system during body movements and its interactions with the surroundings. Previous psychophysical and neurophysiological studies have focused on spatial location perception of the upper body. In this study, we recorded single-trial electroencephalography (EEG) responses evoked by four vibrotactile stimulators placed on the buttocks and thighs while the human subject was sitting in a chair with a cushion. Methods: Briefly, 14 human subjects were instructed to sit in a chair for a duration of 1 h or 1 h and 45 min. Two types of cushions were tested with each subject: a foam cushion and an air-cell-based cushion dedicated for wheelchair users to alleviate tissue stress. Vibrotactile stimulations were applied to the sitting interface at the beginning and end of the sitting period. Somatosensory-evoked potentials were obtained using a 32-channel EEG. An artificial neural net was used to predict the tactile locations based on the evoked EEG power. Results: We found that single-trial beta (13–30 Hz) and gamma (30–50 Hz) waves can best predict the tactor locations with an accuracy of up to 65%. Female subjects showed the highest performances, while males’ sensitivity tended to degrade after the sitting period. A three-way ANOVA analysis indicated that the air-cell cushion maintained location sensitivity better than the foam cushion. Conclusion: Our finding shows that tactile location information is encoded in EEG responses and provides insights on the fundamental mechanisms of the tactile system, as well as applications in brain–computer interfaces that rely on tactile stimulation.

Piled raft foundations, wherein a small number of connected piles are utilized as settlement reducers, have been widely used for high-rise buildings. Recently, a new technique has been introduced by disconnecting the piles from the raft and inserting a cushion layer between them. In such cases, the piles are considered as soil reinforcement components rather than structural members. To explore the feasibility of utilizing the disconnected piled raft foundation, a series of experimental model tests were conducted to examine the load–settlement behavior and pile load sharing ratio of the connected piled raft (CPR) and disconnected piled raft (DCPR) foundation systems using cushions of different thicknesses and stiffnesses. In addition, ABAQUS 3D finite element analyses were performed to analyze the axial stress along the piles and the bending moments along the raft. The results indicated that the total settlement of the system was minimized significantly when disconnected piles were used. In addition, the disconnected technique provided a significant reduction in the axial stress along the piles and the bending moment along the raft compared with that of the CPR. These findings may be accompanied by economic and environmental benefits. [ABSTRACT FROM AUTHOR]

Abstract Background Custom orthoses are becoming more commonly prescribed for upper and lower limbs. They require some form of shape-capture of the body parts they will be in contact with, which generates an STL file that designers prepare for manufacturing. For larger devices such as custom-contoured wheelchair cushions, the STL created during shape-capture can contain hundreds of thousands of tessellations, making them difficult to alter and prepare for manufacturing using mesh-editing software. This study covers the development and testing of a mesh-to-surface workflow in a parametric computer-aided design software using its visual programming language such that STL files of custom wheelchair cushions can be efficiently converted into a parametric single surface. Methods A volunteer in the clinical space with expertise in computer-aided design aided was interviewed to understand and document the current workflow for creating a single surface from an STL file of a custom wheelchair cushion. To understand the user needs of typical clinical workers with little computer-aided design experience, potential end-users of the process were tasked with completing the workflow and providing feedback during the experience. This feedback was used to automate part of the computer-aided design process using a visual programming tool, creating a new semi-automated workflow for mesh-to-surface translation. Both the original and semi-automated process were then evaluated by nine volunteers with varying levels of computer-aided design experience. Results The semi-automated process showed a 37% reduction in the total number of steps required to convert an STL model to a parametric surface. Regardless of previous computer-aided design experience, volunteers completed the semi-automated workflow 31% faster on average than the manual workflow. Conclusions The creation of a semi-automated process for creating a single parametric surface of a custom wheelchair cushion from an STL mesh makes mesh-to-surface conversion more efficient and more user-friendly to all, regardless of computer-aided design experience levels. The steps followed in this study may guide others in the development of their own mesh-to-surface tools in the wheelchair sector, as well as those creating other large custom prosthetic devices.

Precast concrete block slope protection is widely used due to its advantages of easy detection and laying, ease of organization, and the limited time required for construction. In order to prevent the soil or gravel bedding of precast concrete from being subjected to wind and wave pressures, the joints between precast concrete blocks are usually filled with mortar. However, the existing standards do not specify the width or material of the joints. Furthermore, excessively wide mortar joints or shrinkage of the mortar can result in loss, a hollowed-out cushion, and damage to the slope, thus compromising the quality of slope protection engineering. To establish standards for controlling the quality of slope protection seams, this paper designed and conducted a physical model test of precast concrete block revetment seams. By embedding pore water pressure sensors in the cushion layer, changes in the pore water pressure were observed under varying conditions, including different water pore pressure sensor locations, water levels in front of the embankment, and different joint widths. Based on the test results, design standards for joint widths and recommendations for the treatment of joint mortar materials were proposed. After adding different amounts of a calcium oxide–calcium sulfoaluminate composite expansion agent (HME) into a joint mortar material, the paper also carried out a shear test on the contact surface between the joint mortar and the slope protection concrete after adding varying amounts of a calcium oxide-calcium sulfoaluminate composite expansion agent (HME) to the joint mortar material. Following a microporous structure test, recommendations for joint mortar construction treatment were proposed. The results indicate that the pore water pressure of the precast concrete slope protection cushion is closely related to the position of the cushion, the water level in front of the embankment, and the width of the paving seam. When the masonry seam width increased from 0.5 mm to 1 mm and from 1 mm to 1.5 mm, the variation ranges of the pore water pressure were 40–80% and 6–20%, respectively, with the latter being significantly lower than the former. Therefore, in practical engineering, joint treatment should take into account the impact of the cushion position, the water level in front of the dike, and the joint mortar width. Mortar shedding within the range of wave climbing height should be addressed promptly, and joint width should be controlled to below 1 cm as much as possible to effectively prevent damage to the cushion surface. The addition of an expansion agent can improve the bond strength of the concrete and mortar to a certain extent. The study found that an 8% content of the expansion agent resulted in the best mortar bond strength and the densest microstructure. These research findings can serve as a basis for the development of quality control standards for precast concrete slope protection. [ABSTRACT FROM AUTHOR]

Practicing geoengineers and researchers generally consider the load sharing behavior in multi-type pile composite foundation as an important design aspect. On the other hand, due to urbanization, such foundation system in cities will inevitably appear next to supported excavation. This paper discusses the result from relatively largescale indoor experiment conducted to investigate the load sharing behavior of loaded long-short CFG pile composite foundation behind a neighboring rigid retaining wall undergoing rotation around the bottom. It was found that with progression of wall movement, the hidden load from soil displacement was borne by the piles with marked reduction in soil load sharing. At the end of wall rotation, the percentage of long piles’ head load increment needed to arrive at a new static equilibrium was about 12.57~32.22% while the end bearing increased by more than 97%. The consequences on the short piles, however, were manifested with an increasing pile head (13.42%) and toe (28.9%) load for the pile far from the wall whereas the closest one experienced a certain increment up to 15×10-4rad wall rotation and finally the head load and end bearing decreased to 8.28% and 12.63%, respectively. The 3D numerical back analysis conducted using FE software ABAQUS yielded the pile – soil stress ratio lower than the value obtained from the experiment but provided great insight into pile settlement characteristics during wall rotation. [ABSTRACT FROM AUTHOR]

The purpose of this study is to clarify impact response of no-shear-reinforcement reinforced concrete (RC) beams having cushion layers subjected to impact loading. The beams, which are designed with Polystyrene (Beam S type) and Polycarbonate (Beam P type), were tested by drop-weight experiment with various height of impact at 4.0, 4.5 and 5 m compared to no-cushion-designed beam (Beam N) at accordingly impact velocities. The weight of 169 kg was free falling to mid-span of the beams which have dimension of width, depth and clear span length are 150, 250 and 2000 mm. After testing, crack patterns propagated from the side surfaces of the RC beams was sketched, and impact forces, reaction forces and mid-span deflection was measured and recorded by wide-band analog data recorders. In addition, a comparative static loading test of no-stirrup beam (Beam NS) was used to establish an analytical fiber model of the beam under impact loading. The results obtained are as follows: 1) No-stirrup RC beams governed by shear-failure-mode or combined shear- and flexural- failure mode with diagonal cracks, while those with cushion almost exhibited flexural-failure-mode with significant fewer cracks; 2) At velocity of 4 m/s, no-cushion-designed beam’s performance indicate the yielding stage in brittle failure mode of no-stirrup RC beam; 3) To quantitively estimate the contribution of the cushion on the beam have and have-not cushion, a proposed simplified fiber model was used with comparison to its static performance in order to determined maximum deflection of the beams; 4) It is assumed that initial dissipated energy does not occurred in beams have cushion, while beams have-not cushion own this due to its brittle failure mode; 5) It is found that estimated maximum deflections of the beam are in line with the measured values; 6) Dynamic absorbed energy of the cushion are higher than static absorbed energy of the cushions, which lead to higher contribution of the cushion in impact event.

Pile composite foundation (PCF) supporting anchorage foundations and immersed tube foundations is subjected to significant vertical and lateral loads, where the PCF design is often controlled by the lateral displacement of PCF head. Therefore, the behavior of lateral loaded PCF is an important issue concerned by engineers, but no published design guidance can be referred. An semi-analytical method is adopted to predict the lateral loaded PCF behaviors, where the reduction factor of the t-th row fp(t) and group efficiency factor fg are induced to account for the group effects. The PCF system is decomposed into fictitious piles and extended soil, and fictitious piles are treated as Bernoulli-Euler beam. The governing equation is formulated based on the compatibility condition of lateral displacement between extended soil and fictitious piles and solved by numerical solution. The analytical results are validated against public theoretical solutions and FEM solutions, and provide very satisfactory results. The PCF behaviors, reduction factor per row fp(t) and group efficiency factor fg are widely investigated by considering some primary influence factors, such as the ratio of pile length to diameter l/d, the ratio of pile spacing to diameter s/d, the number of piles N and the layout form. It is shown that: (1) the surface load on soil elements between piles take a noticeable influence on the deflection and moment distribution along pile shaft; (2) the lateral stiffness of the i-th pile ki, fp(t), fg decrease with increasing s/d, and the l/d has a negligible effect on the fp(t) and fg; (3) the fg of in-line layout is larger than the fg of square array layout and smaller than side-by-side layout form, and fg decrease with the increasing the number of piles N in PCF regardless of pile layout form. The research is expected to provide insights to the practitioners on the lateral loaded PCF design.

Background: Custom orthoses are becoming more commonly prescribed for upper and lower limbs. They require some form of shape-capture of the body parts they will be in contact with, which generates an STL file that designers prepare for manufacturing. For larger devices such as custom-contoured wheelchair cushions, the STL created during shape-capture can contain hundreds of thousands of tessellations, making them difficult to alter and prepare for manufacturing using mesh-editing software. This study covers the development and testing of a mesh-to-surface workflow in a parametric computer-aided design software using its visual programming language such that STL files of custom wheelchair cushions can be efficiently converted into a parametric single surface. Methods: A volunteer in the clinical space with expertise in computer-aided design aided was interviewed to understand and document the current workflow for creating a single surface from an STL file of a custom wheelchair cushion. To understand the user needs of typical clinical workers with little computer-aided design experience, potential end-users of the process were tasked with completing the workflow and providing feedback during the experience. This feedback was used to automate part of the computer-aided design process using a visual programming tool, creating a new semi-automated workflow for mesh-to-surface translation. Both the original and semi-automated process were then evaluated by nine volunteers with varying levels of computer-aided design experience. Results: The semi-automated process showed a 37% reduction in the total number of steps required to convert an STL model to a parametric surface. Regardless of previous computer-aided design experience, volunteers completed the semi-automated workflow 31% faster on average than the manual workflow. Conclusions: The creation of a semi-automated process for creating a single parametric surface of a custom wheelchair cushion from an STL mesh makes mesh-to-surface conversion more efficient and more user-friendly to all, regardless of computer-aided design experience levels. The steps followed in this study may guide others in the development of their own mesh-to-surface tools in the wheelchair sector, as well as those creating other large custom prosthetic devices. [ABSTRACT FROM AUTHOR]

Develop an anthropomorphic model cushion rigid loading indenter with embedded sensors (AMCRLI-ES) to assess compression and shear forces at key locations such as trochanters and ischial tuberosities. The sensor design was optimized using finite element analysis. The AMCRLI-ES was designed with the same dimensions as specified in ISO 16840–2 tests. The AMCRLI-ES is divided into eight independent sections, and each section consists of one 3-axis load cell sensor to measure compression and shear forces normal to the compression direction. Six commercial cushions were tested using the AMCRLI-ES with standard ISO 16840–2 testing procedures. Statistical differences were found for energy dissipation between cushions. Statistical differences (p < 0.001) were found in all stiffness values. Test results showed that energy dissipation (ED) was correlated with hysteresis at 500 N with moderate to high Pearson product correlation r = -0.537, p = 0.022. The hysteresis at 250 N did not show a statistical correlation with ED. The AMCRLI-ES demonstrated the ability to measure compression and shear forces at key locations on the cushion including the thigh, trochanter, ischial tuberosity, and sacral area. It provides in-depth information about how the weight was distributed on the cushions. [ABSTRACT FROM AUTHOR]

Settlement of the pile ends in end-bearing rigid pile composite foundations is generally minimal, so only relying on the cushion to coordinate the pile soil deformation may result in insufficient deformation adjustment capacity. Using a deformation adjustor with a specific stiffness on the top of the pile is a method to coordinate pile–soil deformation, and the stiffness value of the deformation adjustor depends on the accurate calculation of soil deformation; however, the calculation of soil deformation is not mature at present. A new deformation adjustor based on strengths used in composite foundations is proposed, in which foam slabs with different yield strengths are placed on the top of the pile to coordinate the pile–soil deformation. Five tests are used to study the mechanical and deformation properties of a composite foundation with a foam slab. The test results show that when the stress at the top of the pile is less than the yield strength of the foam slab, the coordination of the pile–soil deformation mainly depends on the cushion. When the stress of a rigid pile exceeds the yield strength of foam concrete, the foam slab begins to yield and coordinate the deformation of pile and soil, and the settlement coordination ability of a rigid pile composite foundation with a foam slab is significantly improved. Finally, an engineering case is used to simulate the pile–soil stress sharing when the actual settlement is greater than the calculated settlement. The case analysis shows that the pile-top stress can be well controlled by the successive yielding of foam concrete slabs of different strengths, which reduces the influence of settlement error on the pile–soil stress sharing, and further promotes the engineering application of end-bearing rigid pile composite foundations. [ABSTRACT FROM AUTHOR]

Purpose: The aim of this experimental study was to compare the ability of polyurethane cushions of three arbitrary selected thicknesses to minimize vibrations transmitted from the wheelchair to its user. Methods: Measurements were made during passive motion on five different surfaces often found in public spaces. Two tests were carried out during the measurements. In the first test, the sensor was located directly on the surface of the wheelchair seat. In the second test, a polyurethane cushion was placed on the seat, on which the measuring sensor was then placed. Results: The study showed that regardless of the surface on which the wheelchair user moves, the threshold defined in the ISO standard for frequencies in the range of 4-40 Hz was exceeded. However, thanks to the use of polyurethane cushions, vibration damping was visible for frequencies ranging from 10 to 40 Hz. The impact of the user's weight on the magnitude of the perceived vibrations was also observed. Conclusions: Studies show that wheelchair users are exposed to whole body vibration that can negatively affect their health. Cushions made of polyurethane seem to be a promising solution to reduce whole body vibration in the frequency range that is burdensome and harmful to human health. [ABSTRACT FROM AUTHOR]

Ensuring the safety of existing structures is an important issue when planning and executing adjacent new foundation pit excavations. Hence, understanding the stress state conditions experienced by the soil element behind a retaining wall at a given location during different excavation stages has been a key observational modelling aspect of the performance of excavations. By establishing and carrying out sophisticated soil–structure interaction analyses, stress paths render clarity on soil deformation mechanism. On the other hand, column-type soft ground treatment has recently got exceeding attention and practical implementation. So, the soil stress–strain response to excavation-induced disturbances needs to be known as well. To this end, this paper discusses the stress change and redistribution phenomena in a treated ground based on 3D numerical analyses. The simulation was verified against results from a 1 g indoor experimental test conducted on composite foundation reinforced with long and short cement–fly ash–gravel (CFG) pile adjacent to a moving rigid retaining wall. It was observed that the stress path for each monitoring point in the shallow depth undergoes a process of stress unloading at various dropping amounts of principal stress components in a complex manner. The closer the soil element is to the wall, the more it experiences a change in principal stress components as the wall movement progresses; also, the induced stress disturbance weakens significantly as the observation point becomes farther away from the wall. Accordingly, the overall vertical load-sharing percentage of the upper soil reduces proportionally.

Over the past few decades, interest has grown about the role of the piled raft structure in soils. A structural fill cushion separates the piles from the raft in the form of an unconnected piled raft base (UCPRF). Given the advantage of this structure, the load is dispersed between the raft and the piles by the cushion. The cushion serves as a load redistributor between the raft and the piles. Load dispersion capability of the system was theoretically estimated using PLAXIS finite element analysis software in this study. The effect of cushion thickness on settlement reductions was investigated as well. Obtained results showed that the pile head has the greatest axial stress in the piled raft system., however decreased along the length of the pile according to finite element analysis. The unconnected head's maximum axial load is transferred down to a point a certain distance below the pile head (approximately two meters in the studied model). Above the top two meters, the axial stress in the pile begins to decrease, following the same pattern as the connected system. The thickness of the cushion affects the load sharing between the cushion and the piles. As the cushion thickness increases, the axial stress at the pile head decreases

This study focusses on numerical analysis to clarify the effect of four types of high strength expanded materials on reinforced concrete (RC) beams subjected to impact of weight falling from a height. LS-DYNA numerical code was used to simulate the dynamic response of the cushions (three are Polystyrene and one is Polycarbonate), and its RC beams during drop-weight impact event. Based on proposed constitutive finite element (FE) models of concrete (MAT_SCHWER_MURRAY_CAP_MODEL_145), steel (MAT_PIECEWISE_LINEAR_024) and cushions (MAT_CRUSHABLE_FOAM_063), the numerical results, i.e., impact forces, mid-span deflection waves and crack patterns, saw good agreement with those from the experimental results. It is confirmed on the proposed numerical model of RC beams with and without cushion subjected to impact loading that the higher protective characteristic of the cushion was hired, the fewer damages on the RC beam were observed.

Many countries are developing new ways to protect Reinforced Concrete (RC) structures under specific risks such as rockfall hazards. Cushioning materials, for example, are using to improve the impact resistance of the RC structures. Applying cushions improves the strength of RC structures under aging of materials and deteriorations, therefore, it improves the safety of people, buildings, and infrastructure systems. However, the impact resistance of RC structures with cushions have not yet been clarified. This study aims to clarify the effect of four types of high strength expanded materials, three are Polystyrene and one is Polycarbonate, which were set on RC beams to enhance impact resistance of the beams. Drop weight tests were employed to investigate the mechanical behavior of RC beams with cushions. The following conclusions were found based on the results of this study: 1) High energy absorbing cushions should be used to protect RC beams subjected to impact loadings as it significantly reduced the maximum deflection and crack opening process of the beams. 2) The hardening effect of concrete at upper cover surface of RC beam during collision were confirmed by using yielding static test. It is used to calibrate static fiber model of normal RC beam to obtain the maximum deflection due to impact loadings. 3) The impact absorbing energy of the cushions were verified to establish simplified equation of maximum deflections of the beam with cushions. 4) The estimated maximum deflections of RC beams with and without cushions are in agreement with the measured values.

Precast concrete block slope protection is widely used due to its advantages of easy detection and laying, ease of organization, and the limited time required for construction. In order to prevent the soil or gravel bedding of precast concrete from being subjected to wind and wave pressures, the joints between precast concrete blocks are usually filled with mortar. However, the existing standards do not specify the width or material of the joints. Furthermore, excessively wide mortar joints or shrinkage of the mortar can result in loss, a hollowed-out cushion, and damage to the slope, thus compromising the quality of slope protection engineering. To establish standards for controlling the quality of slope protection seams, this paper designed and conducted a physical model test of precast concrete block revetment seams. By embedding pore water pressure sensors in the cushion layer, changes in the pore water pressure were observed under varying conditions, including different water pore pressure sensor locations, water levels in front of the embankment, and different joint widths. Based on the test results, design standards for joint widths and recommendations for the treatment of joint mortar materials were proposed. After adding different amounts of a calcium oxide–calcium sulfoaluminate composite expansion agent (HME) into a joint mortar material, the paper also carried out a shear test on the contact surface between the joint mortar and the slope protection concrete after adding varying amounts of a calcium oxide-calcium sulfoaluminate composite expansion agent (HME) to the joint mortar material. Following a microporous structure test, recommendations for joint mortar construction treatment were proposed. The results indicate that the pore water pressure of the precast concrete slope protection cushion is closely related to the position of the cushion, the water level in front of the embankment, and the width of the paving seam. When the masonry seam width increased from 0.5 mm to 1 mm and from 1 mm to 1.5 mm, the variation ranges of the pore water pressure were 40–80% and 6–20%, respectively, with the latter being significantly lower than the former. Therefore, in practical engineering, joint treatment should take into account the impact of the cushion position, the water level in front of the dike, and the joint mortar width. Mortar shedding within the range of wave climbing height should be addressed promptly, and joint width should be controlled to below 1 cm as much as possible to effectively prevent damage to the cushion surface. The addition of an expansion agent can improve the bond strength of the concrete and mortar to a certain extent. The study found that an 8% content of the expansion agent resulted in the best mortar bond strength and the densest microstructure. These research findings can serve as a basis for the development of quality control standards for precast concrete slope protection.

Traditional methods of shape-capture for creating custom-contoured seating have commonly consisted of capturing the buttocks in a loaded position. This study seeks to compare an innovative unloaded shape capture method to off-the-shelf pressure relieving cushions. The pressure redistribution and support characteristics of a cushion designed using an unloaded shape-capture method was compared to off-the-shelf pressure redistributing cushions. The methods of this pilot trial are described, and the outcomes are analyzed and summarized through descriptive statistics, including peak pressure index, average pressure, surface contact, quadrant distribution and perception of postural support. A Wilcoxon signed-rank test was calculated to compare the mean difference in PPI between the unloaded shape-capture cushion among the other cushions. Differences in peak pressure between the unloaded shape capture cushion and off-the-shelf pressure relieving cushions were not significant, however there was a significant reduction in pressure between the unloaded shape-capture cushion and both sling seat and baseline non-contoured foam cushion (z = 2.673, p =.008). The unloaded shape-capture method results in a cushion with pressure redistribution characteristics similar to off-the-shelf pressure redistributing cushions while providing superior postural support. The unloaded shape-capture method appears to be a feasible alternative to traditional loaded methods and is worthy of further research. • Unloaded shape capture provides a novel method for creating custom contoured cushions. • Unloaded shape capture results in similar pressure reduction when compared to loaded. • All feedback and comments from the reviewer have been carefully considered and incorporated into the manuscript. • Unloaded shape capture results in significant improvement over baseline and sling seating. [ABSTRACT FROM AUTHOR]

Copyright of Coal Science & Technology (0253-2336) is the property of Coal Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This study proposes a high‐resilience foam‐core composite with bionic micro‐interface lattice structure using columnar lattice mold and two‐step foaming technique. This foam‐core composite uses polyamides nonwoven fabrics as the bionic surface layers and polyurethane foam as the bionic core layer. The foam cavity diameter and columnar interface area are adjusted by the polyols content and the column diameter, respectively. Effects of the cavity diameter and the column diameter on the compression resistance, static‐bursting strength, low‐velocity impact, and dynamic cushion efficacy of foam‐core composites are investigated. The results show that compression resistance, bursting strength, and cushion efficacy of the foam‐core composites are all increased by degrees with the cavity diameter when the content of polyols increases. When the cavity diameter was 195 μm, bionic micro‐interface foam‐core composite absorbed 99% low‐velocity impact energy. Existence of bionic micro‐interface lattice obviously improved the static compression and bursting properties. Bionic micro‐interface foam‐core composites with 16 mm‐diameter column have the lower and wider contact force peak compared to pomelo, 8 mm and 12 mm‐diameter column, indicating higher dynamic cushion efficacy. The resulted composite provides an idea of establishing bionic foam‐core cushion composites by foam interface, which is expected to be used as energy absorption material for commercial application. [ABSTRACT FROM AUTHOR]

Study aim: The aim of this study was to determine the optimal angle for maximizing pressure distribution in two types of wheelchairs (tilting and reclining) while using a ROHO cushion, which offers relatively effective pressure distribution.

Copyright of Journal of Architecture & Civil Engineering is the property of Chang'an Daxue Zazhishe and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Journal of Mosaic Research is the property of Uludag University, Mosaic Research Center and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The cushion of a geomembrane surface barrier of a high rockfill dam built on deep overburden is prone to crack and fail because of excessive flexural deformation. This study proposes a geomembrane surface barrier for a high rockfill dam on deep overburden. The proposed geomembrane surface barrier uses polyurethane bonded aggregates as the cushion material. The loading and deformation performance of the barrier system under uniform water pressure was investigated using a self-developed structure model test device. The mechanical and deformation property of each layer of the barrier, and the interaction mode between adjacent layers, were obtained through external videos and internal sensor monitoring. The results demonstrated that the polyurethane bonded aggregate cushion exhibited good adaptability to flexural deformation during the entire loading process and maintained good contact and coordinate deformation with the upper protective and the lower transition layers. The geomembrane surface barrier created using polyurethane bonded aggregates as the cushion material can adapt to the flexural deformation of a high rockfill dam surface on deep overburden. [ABSTRACT FROM AUTHOR]