Search

Background: Osteochondral allograft (OCA) transplantation is an important surgical technique for full-thickness chondral defects in the knee. For patients undergoing this procedure, topography matching between the donor and recipient sites is essential to limit premature wear of the OCA. Currently, there is no standardized process of donor and recipient graft matching. Purpose: To evaluate a novel topography matching technique for distal femoral condyle OCA transplantation using 3-dimensional (3D) laser scanning to create 3D-printed patient-specific instrumentation in a human cadaveric model. Study Design: Descriptive laboratory study. Methods: Human cadaveric distal femoral condyles (n = 12) underwent 3D laser scanning. An 18-mm circular osteochondral recipient defect was virtually created on the medial femoral condyle (MFC), and the position and orientation of the best topography-matched osteochondral graft from a paired donor lateral femoral condyle (LFC) were determined using an in silico analysis algorithm minimizing articular step-off distances between the edges of the graft and recipient defect. Distances between the entire surface of the OCA graft and the underneath surface of the MFC were evaluated as surface mismatch. Donor (LFC) and recipient (MFC) 3D-printed patient-specific guides were created based on 3D reconstructions of the scanned condyles. Through use of the guides, OCAs were harvested from the LFC and transplanted to the reamed recipient defect site (MFC). The post-OCA recipient condyles were laser scanned. The 360° articular step-off and cartilage topography mismatch were measured. Results: The mean cartilage step-off and graft surface mismatch for the in silico OCA transplant were 0.073 ± 0.029 mm (range, 0.005-0.113 mm) and 0.166 ± 0.039 mm (range, 0.120-0.243 mm), respectively. Comparatively, the cadaveric specimens postimplant had significantly larger step-off differences (0.173 ± 0.085 mm; range, 0.082-0.399 mm; P =.001) but equivalent graft surface topography matching (0.181 ± 0.080 mm; range, 0.087-0.396 mm; P =.678). All 12 OCA transplants had mean circumferential step-off differences less than a clinically significant cutoff of 0.5 mm. Conclusion: These findings suggest that the use of 3D-printed patient-specific guides for OCA transplantation has the ability to reliably optimize cartilage topography matching for LFC to MFC transplantation. This study demonstrated substantially lower step-off values compared with previous orthopaedic literature when also evaluating LFC to MFC transplantation. Using this novel technique in a model performing MFC to MFC transplantation has the potential to yield further enhanced results due to improved radii of curvature matching. Clinical Relevance: Topography-matched graft implantation for focal chondral defects of the knee in patients improves surface matching and has the potential to improve long-term outcomes. Efficient selection of the allograft also allows improved availability of the limited allograft sources. [ABSTRACT FROM AUTHOR]

Background: Approximately 90% of patients who undergo arthroscopic rotator cuff repair (RCR) are satisfied with their pain levels and function after surgery. However, a subset of patients experience continued symptoms that warrant revision surgery. Preoperative risk factors for RCR failure requiring revision surgery have not been clearly defined. Purpose: To (1) determine the rate of RCR failure requiring revision surgery and (2) identify risk factors for revision surgery, which will help surgeons to determine patients who are at the greatest risk for RCR failure. Study Design: Systematic review and meta-analysis; Level of evidence, 4. Methods: A systematic review and meta-analysis in accordance with PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) guidelines were performed. The initial search resulted in 3158 titles, and 533 full-text articles were assessed for eligibility. A total of 10 studies met the following inclusion criteria: (1) human clinical studies, (2) arthroscopic RCR, (3) original clinical research, and (4) evaluation of preoperative risk factors for revision. Results: After a full-text review, a total of 16 risk factors were recorded and analyzed across 10 studies. Corticosteroid injection was the most consistent risk factor for revision surgery, reaching statistical significance in 4 of 4 studies, followed by workers' compensation status (2/3 studies). Patients with corticosteroid injections had a pooled increased risk of revision surgery by 47% (odds ratio, 1.44 [95% CI, 1.36-1.52]). Patients with workers' compensation had a pooled increased risk of revision surgery by 133% (odds ratio, 2.33 [95% CI, 2.09-2.60]). Age, smoking status, diabetes, and obesity were found to be risk factors in half of the analyzed studies. Conclusion: Corticosteroid injections, regardless of the frequency of injections, and workers' compensation status were found to be significant risk factors across the literature based on qualitative analysis and pooled analysis. Surgeons should determine ideal candidates for arthroscopic RCR by accounting for corticosteroid injection history, regardless of the frequency, and insurance status of the patient. [ABSTRACT FROM AUTHOR]

Background: All-suture anchors and knotless anchors are increasingly used in the repair of anteroinferior labral tears in patients with shoulder instability. Optimal repair constructs may limit recurrent instability. Purpose: To perform a quantitative biomechanical comparison of 3 labral fixation devices for soft tissue Bankart lesions: knotless soft-body tensionable anchor (SB knotless), knotted soft-body anchor (SB knotted), and knotless hard-body PEEK (polyether ether ketone) interference anchor (HB knotless). Study Design: Controlled laboratory study. Methods: A total of 21 glenoid specimens were randomized into 3 groups: SB knotless, SB knotted, and HB knotless. Artificial Bankart lesions were created at the anteroinferior labrum. Anchors were placed at the 3:30, 4:30, and 5:30 clockface positions, and sutures were passed through 1 cm of tissue. Anchors were tested simultaneously as one construct by pulling capsular tissue connected to the anteroinferior quadrant. Cyclic loading (5-25 N, 100 cycles) was followed by load-to-failure testing (15 mm/min). Biomechanical testing variables were collected, and failure mechanisms were recorded per individual anchor. Results: There were no differences in baseline specimen characteristics. There was no difference in elongation during cyclic loading (P =.40). The ultimate load to failure between SB knotless (309.7 ± 125.6 N), SB knotted (226.4 ± 34.8 N), and HB knotless (256.5 ± 90.5 N) did not significantly differ (P =.25). Failure mechanisms differed among groups (P =.008); mechanisms included anchor pullout (SB knotless: 33.3%; SB knotted: 23.8%; HB knotless: 28.6%), suture pull-through (SB knotless: 66.7%; SB knotted: 38.1%; HB knotless: 33.3%), and anchor fixation method failure, defined as knot failure for knotted anchors or locking mechanism failure for knotless anchors (SB knotless: 0.0%; SB knotted: 38.1%; HB knotless: 38.1%).) Conclusion: The SB knotless, SB knotted, and HB knotless labral fixation anchors studied exhibited comparable elongation during cyclic loading, stiffness, and ultimate loads to failure in a cadaveric model. However, the failure mechanisms significantly differed, as SB knotless anchors failed primarily from suture pull-through, while SB knotted and HB knotless anchors were subject to knot failure and locking mechanism failure, respectively. Clinical Relevance: These data support the benefit of SB knotless anchors for anteroinferior labral repair in limiting knot failure typically seen with knotted anchors, perhaps demonstrating that all-suture anchors may have better locking mechanism quality than their PEEK counterparts. [ABSTRACT FROM AUTHOR]

Background: Tibial tubercle–trochlear groove (TT-TG) distance is a risk factor for recurrent patellar dislocation and is often included in algorithmic treatment of instability. The underlying factors that determine TT-TG have yet to be clearly described in orthopaedic literature. Purpose/Hypothesis: The purpose of our study was to determine the underlying anatomic factors contributing to TT-TG distance. We hypothesized that degree of tubercle lateralization and knee rotation angle may substantially predict TT-TG. Study Design: Cross-sectional study; Level of evidence, 3. Methods: All patients evaluated for patellar instability at a single institution between 2013 and 2021 were included. Patients with previous knee osseous procedures were excluded. TT-TG and its anatomic relationship to patellofemoral measures, including dysplasia, femoral anteversion, tibial tubercle lateralization, knee rotation angle, and tibial torsion, were measured and subsequently quantified using univariate and multivariable analysis. Results: In total, 76 patients met the inclusion criteria (46 female, 30 male; mean ± SD age, 20.6 ± 8.6 years) and were evaluated. Mean TT-TG was 16.2 ± 5.4 mm. On univariate analysis, increasing knee rotation angle (P <.01), tibial tubercle lateralization (P =.02), and tibial torsion (P =.01) were associated with increased TT-TG. In dysplastic cases, patients without medial hypoplasia (Dejour A or B) demonstrated significantly increased TT-TG (18.1 ± 5.4 mm) as compared with those with medial hypoplasia (Dejour C or D; TT-TG: 14.9 ± 5.2 mm; P =.02). Multivariable analysis revealed that increased knee rotation angle (+0.43-mm TT-TG per degree; P <.01) and tubercle lateralization (+0.19-mm TT-TG per percentage lateralization; P <.01) were statistically significant determinants of increased TT-TG distance. Upon accounting for these factors, tibial torsion, trochlear width, and medial hypoplasia were no longer significant components in predicting TT-TG (P ≥.54). Of note, all patients with TT-TG ≥20 mm had tibial tubercle lateralization ≥68%, a knee rotation angle ≥5.8°, or both factors concurrently. Conclusion: TT-TG distance is most influenced by knee rotation angle and tibial tubercle lateralization. [ABSTRACT FROM AUTHOR]

Case: A 12-year-old adolescent boy presented after a low-energy fall with groin pain, inability to bear weight, painful passive range of motion, fever, elevated inflammatory markers, and upper respiratory symptoms. Initial radiographs did not demonstrate any abnormality, and magnetic resonance imaging suggested infection. Posterior wall acetabular fracture was not diagnosed until a computed tomography-guided biopsy was performed., Conclusion: Pediatric acetabular fractures are exceedingly rare. They can be difficult to diagnose after low-energy trauma as symptoms mimic infectious hip pathologies. Children presenting with infectious hip symptomology and a history of trauma may benefit from more extensive trauma imaging before costly and invasive infectious diagnostic procedures., Competing Interests: Disclosure: The Disclosure of Potential Conflicts of Interest forms are provided with the online version of the article (http://links.lww.com/JBJSCC/C192)., (Copyright © 2023 by The Journal of Bone and Joint Surgery, Incorporated.)