Search

We describe the fabrication of a controllable microfluidic valve coupled with an electrochemical pump, which has been designed to deliver reagents to an integrated microfluidic biosensing system. Fluid, retained within an insertion reservoir using a stop valve, was pumped using electrochemical actuation, providing a low power, low voltage integrated Laboratory-on-a-Chip for reproducible, small volume fluidic manipulation. The properties of the valve were characterized using both X-ray photoelectron spectroscopy and contact angle measurements, enabling the calculation of the magnitude of the forces involved (which were subsequently verified through experimental measurement). Electrochemical generation of oxygen and hydrogen acted as an on-demand pressure system to force fluid over the stop valve barrier. The process of filling-up the biosensing chamber was characterized in terms of the time to fill, the energy used, and the peak power consumed. The potential of the device was illustrated using a glucose biosensor.

In this paper, we present a radiotelemetry sensor, designed as a lab-in-a-pill, which incorporates a two-channel micro-fabricated sensor platform for real-time measurements of temperature and pH. These two parameters have potential application for use in remote biological sensing (for example they may be used as markers that reflect the physiological environment or as indicators for disease, within the gastrointestinal tract). We have investigated the effects of biofouling on these sensors, by exploring their a response time and sensitivity in a model in vitro gastrointestinal system. The artificial gastric and intestinal solutions used represent a model both for fasting, as well as for the ingestion of food and subsequent digestion to gastrointestinal chyme. The results showed a decrease in pH sensitivity after exposure of the sensors for 3 h. The response time also increased from an initial measurement time of 10 s in pure GI juice, to ca. 25 s following the ingestion of food and 80 s in simulated chyme. These in vitro results indicate that changes in viscosity in our model gastrointestinal system had a pronounced effect on the unmodified sensor. Index Terms--Biofouling, in vitro measurements, lab-in-a-pill, microfabricated sensors, radio telemetry.

We describe a method, based on X-ray photoelectron spectroscopy (XPS) measurements, to assess the extent of protein adsorption or binding on a variety of different [micro]TAS and biosensor interfaces. Underpinning this method is the labeling of protein molecules with either iodine- or bromine-containing motifs by using protocols previously developed for radiotracer studies. Using this method, we have examined the adsorption and binding properties of a variety of modified electrodeposited polymer interfaces as well as other materials used in [micro]TAS device fabrication. Using polymer interfaces modified with poly(propylene glycol) (PPG) chains, our results indicate that a chain of at least ~30 monomer units is required to inhibit nonspecific adsorption from concentrated protein solutions. The XPS methodology was also used to probe specific binding of avidins and enzyme conjugates thereof to biotinylated and mixed biotin/PPG-modified polymer interfaces. In one example, using competitive binding, it was established that the mode of binding of a peroxidase--streptavidin conjugate to a biotinylated modified polymer interface was primarily via the streptavidin moiety (as opposed to nonspecific binding via the enzyme conjugate). XPS evaluation of nonspecific and specific peroxidase--streptavidin immobilization on various functionalized polymers has guided the design and fabrication of functionalized interdigitated electrodes in a biosensing [micro]TAS device. Subsequent characterization of this device using scanning electrochemical microscopy (SECM) corroborated the adsorption and binding previously inferred from XPS measurements on macroscale electrodes.

Electropolymerized films of the functionalized pyrrole, pentafluorophenyl-3-(pyrrol-1-yl)propionate (PFP), were reacted with a solution-phase nucleophile, ferrocene ethylamine. This reaction was chosen as a model representative of a postdeposition modification of the polymer membrane's properties. For the first time, a nondestructive method for direct chemical analysis of the reaction profile within the electrodeposited polymer membrane after nucleophilic substitution is presented. This was achieved through the application of in situ neutron reflectivity with supplementary analytical information concerning the film's chemical composition obtained from XPS, FT-IR, and electrochemical measurements. The results presented illustrate how, for a partially reacted film resulting from a short reaction time, the extent of reaction with ferrocene ethylamine is not homogeneous throughout the thickness of the film, but occurs predominantly at the polymer/solution interface. We show that the progress of the reaction within the polymer film is limited by the transport of reacting species in the dense regions of the membrane that are furthest from the solution interface. The data do not fit an alternative model in which there is spatially homogeneous progression of the reaction front throughout the bulk of the thin film polymer. Guided by the neutron reflectivity measurements, suitable modifications were made to the electrodeposition method to prepare films whose architecture resulted in faster rates of reaction.

A description of in situ neutron reflectivity (NR) and RAIRS studies of the chemical modification of films of a polypyrrole-based conducting polymer derived from the pentafluorophenyl ester of poly(pyrrole-N-propanoic acid) (PFP) electrodeposited on electrode surfaces are presented. The role of the solvent in controlling the rate of reaction with solution-based nucleophiles is explored.

The integration of a range of technologies including microfluidics, surface-enhanced Raman scattering and confocal microspectroscopy has been successfully used to characterize in situ single living CHO (Chinese hamster ovary) cells with a high degree of spatial (in three dimensions) and temporal (1 s per spectrum) resolution. Following the introduction of a continuous flow of ionomycin, the real time spectral response from the cell was monitored during the agonist-evoked Ca2+ flux process. The methodology described has the potential to be used for the study of the cellular dynamics of a range of signalling processes. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

The hydrodynamic interactions of micro-silica spheres trapped in a variety of networks using holographic optical tweezers are measured and characterized in terms of their predicted eigenmodes. The characteristic eigenmodes of the networks are distinguishable within 20-40 seconds of acquisition time. Three different multi-particle networks are considered; an eight-particle linear chain, a nine-particle square grid and, finally, an eight-particle ring. The eigenmodes and their decay rates are shown to behave as predicted by the Oseen tensor and the Langevin equation, respectively. Finally, we demonstrate the potential of using our micro-ring as a non-invasive sensor to the local environmental viscosity, by showing the distortion of the eigenmode spectrum due to the proximity of a planar boundary., (((c) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim).)

A nanocalorimetric suspended membrane sensor for pL volumes of aqueous media was fabricated by bulk silicon micromachining using anisotropic wet etching and photo and electron beam lithographic techniques. A high-temperature sensitivity of 125 microK and a rapid unfiltered time constant of 12 ms have been achieved by integrating a miniaturized reaction vessel of 0.7-nL volume on a 800-nm-thick and 300 x 300- microm2-large silicon nitride membrane, thermally insulated from the surrounding bulk silicon. The combination of a ten-junction gold and nickel thermoelectric sensor with an integrated ultralow noise preamplifier has enabled the resolution of 15-nW power in a single measurement, a result confirmed by electrical calibration. The combination of a high sensitivity and rapid response time is a consequence of miniaturization. The choice of gold and nickel as sensor material provided the maximum thermal sensitivity in the context of ease of fabrication and cost. The nanocalorimetric sensor has the potential for integration in an ultralow-volume high-density array format for the characterization of processes in which there is an exchange of heat.