Search

Analyzing rubber waste is crucial for value-added recycling, but the multitude of ingredients in vulcanized networks makes it challenging to characterize cross-linked rubbers. A combination of analytical techniques is usually required. In this study, two complementary characterization techniques, based on Fourier transform infrared (FTIR) spectroscopy and derivative thermogravimetric analysis (DTGA) were applied to analyze the structural, physical, and thermal behavior of ground tire rubber (GTR) samples devulcanized by two different processes. A set of samples was devulcanized by only microwaves (MW) while another set was treated with a combination of a thermochemomechanical (TM) process, which included the use of a devulcanization aid such as benzoyl peroxide, and microwaves. The combined technique proved to be more efficient in terms of the degree of devulcanization, significantly reducing the cross-linking density. However, the combined thermochemomechanical and microwave (TM/MW) devulcanization process resulted in greater degradation of the main rubber chains in the cross-linked network compared to the process using only microw [ABSTRACT FROM AUTHOR]

The viscoelastic behavior and reinforcement mechanism of polyethylene glycol (PEG) as an interfacial modifier in green tire tread composites were investigated in this study. The results show a clear positive effect on overall performance, and it significantly improved all the parameters of the "magic triangle" properties, the abrasion resistance, wet grip and ice traction, as well as the tire rolling resistance, simultaneously. For the preparation of the compounds, two mixing steps were used, as PEG 4000 was added on the second stage in order to avoid the competing reaction between silica/PEG and silanization. Fourier transform infrared spectroscopy (FTIR) confirmed that PEG could cover the silanol groups on the silica surface, resulting in the shortening of cure times and facilitating an increase of productivity. At low content of PEG, the strength was enhanced by the improvement of silica dispersion and the slippage of PEG chains, which are chemically and physically adsorbed on silica surface, but the use of excess PEG uncombined with silica in the compound, i.e., 5 phr, increases the possibility to shield the disulfide bonds of bis(3-(triethoxysilyl)-propyl) tetrasulfide (TESPT), and, thus, the properties were deteriorated. A constrained polymer model was proposed to explain the constrained chains of PEG in the silica-loaded composites on the basis of these results. An optimum PEG content is necessary for moderately strong matrix–filler interaction and, hence, for the enhancement in the mechanical properties. [ABSTRACT FROM AUTHOR]

This study examines the potential use of sodium alginate (SA) biopolymer as an environmentally sustainable agent for the stabilization of rubberized soil blends prepared using a high plasticity clay soil and tire-derived ground rubber (GR). The experimental program consisted of uniaxial compression and scanning electron microscopy (SEM) tests; the former was performed on three soil-GR blends (with GR-to-soil mass ratios of 0%, 5% and 10%) compacted (and cured for 1, 4, 7 and 14 d) employing distilled water and three SA solutions—prepared at SA-to-water (mass-to-volume) dosage ratios of 5, 10 and 15 g/L—as the compaction liquid. For any given GR content, the greater the SA dosage and/or the longer the curing duration, the higher the uniaxial compressive strength (UCS), with only minor added benefits beyond seven days of curing. This behavior was attributed to the formation and propagation of so-called "cationic bridges" (developed as a result of a "Ca2+/Mg2+ ⟷ Na+ cation exchange/substitution" process among the clay and SA components) between adjacent clay surfaces over time, inducing flocculation of the clay particles. This clay amending mechanism was further verified by means of representative SEM images. Finally, the addition of (and content increase in) GR—which translates to partially replacing the soil clay content with GR particles and hence reducing the number of available attraction sites for the SA molecules to form additional cationic bridges—was found to moderately offset the efficiency of SA treatment. [ABSTRACT FROM AUTHOR]

• Synthesized electrochemically MNPs and funtionalized them with EDTA. • Synthesized Fe 3 O 4 , and Co-doped Fe 3 O 4 , and EDTA-functionalized Co-doped Fe 3 O 4. • Compared curability of nanocomposites in terms of Cure Index. • Obtained Good cure by additional traetment of nanopartcles for their bulk. In this work, the bulk and surface composition of Fe 3 O 4 supermagnetic nanoparticles were modified for efficient epoxy curing. The bare, ethylenediaminetetraacetic acid (EDTA) capped, and cobalt (Co)-doped EDTA capped Fe 3 O 4 nanoparticles were synthesized electrochemically. The crystalline structure and phase information, surface capping, morphology and magnetization behavior of nanoparticles were studied by X-Ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), field-emission scanning electron microscopy (FE-SEM) and vibrating sample magnetometer (VSM), respectively. A low amount of the prepared nanoparticle (0.1 wt.%) was used in preparation of epoxy nanocomposites. Nonisothermal differential scanning calorimetry (DSC) under different heating rates was performed to study the potential of nanoparticles in curing epoxy resin with an aliphatic amine. The heat release data on nanocomposites suggest that EDTA capped Co-doped Fe 3 O 4 considerably improved the curing reaction between epoxy resin and the curing agent. Calculations based on Cure Index approved qualitatively a shift from Poor to Good cure by concurrent lattice and surface modifications of magnetic nanoparticles. It is bielived that the approach used in this work can pave the way to enhance curability of epoxy nanocomposites by the combined modification of bulk and surface of nanoparticles. [ABSTRACT FROM AUTHOR]