Search

In situ immobilization is a widely used measure for passivating Cd-contaminated soils. Amendments need to be continuously applied to achieve stable remediation effects. However, few studies have evaluated the impact of consecutive application of amendments on soil health and the microecological environment. A field experiment was conducted in a Cd-contaminated paddy (available Cd concentration 0.40 mg kg -1 ) on the Chengdu Plain to investigate the changes in soil Cd availability and response characteristics of soil bacterial communities after consecutive application of rice straw biochar (SW), fly ash (FM) and marble powder (YH) amendments from 2018 to 2020. Compared with control treatment without amendments (CK), soil pH increased by 0.6, 0.5 and 1.5 under SW, FM and YH amendments, respectively, and the soil available Cd concentration decreased by 10.71%, 21.42% and 25.00%, respectively. The Cd concentration in rice grain was less than 0.2 mg kg -1 under YH amendment, which was within the Chinese Contaminant Limit in Food of National Food Safety Standards (GB2762-2022) in the second and third years. The three amendments had different effects on the transformation of Cd fractions in soil, which may be relevant to the specific bacterial communities shaped under different treatments. The proportion of Fe-Mn oxide-bound fraction Cd (OX-Cd) increased by 11% under YH treatment, which may be due to the promotion of Fe(III) and Cd binding by some enriched iron-oxidizing bacteria, such as Lysobacter, uncultured_Pelobacter sp. and Sulfurifusis. Candidatus_Tenderia and Sideroxydans were enriched under SW and FM amendments, respectively, and were likely beneficial for reducing Cd availability in soil through Cd immobilization. These results revealed the significance of the bacterial community in soil Cd immobilization after consecutive application of amendments and highlighted the potential of applying YH amendment to ensure the safe production of rice in Cd-contaminated soil., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Inc.)

Increasing municipal solid waste (MSW) production poses challenges for sustainable urban development. Modern energy-from-waste (EfW) facilities incinerate MSW, reducing mass and recovering energy. In the UK, MSW incineration bottom ash (MSW IBA) is primarily reused in civil engineering applications. This study characterizes UK-produced MSW IBA, examining its pH-dependent leaching behaviour and response to environmental lixiviants. Results show predominant components include a melt phase, primary glass and fine ash aggregations, and a chemical composition dominated by SiO 2 (30-50 %), CaO (∼15 %), Fe 2 O 3 (∼10 %), and Al 2 O 3 (∼8%). X-ray absorption near edge structure (XANES) analysis shows that Zn and Cu are most likely oxygen-bound (adsorbed to oxy-hydroxides and as oxides) with some sulphur bound. Polychlorinated biphenyls (PCBs) and polychlorinated dibenzodioxins/furans (PCDD/Fs) are well below regulatory limits, and polycyclic aromatic hydrocarbons (PAHs) were undetectable. Leaching tests indicate trace elements mobilize at pHs ≤ 6. With a natural pH of 11.3 and high buffering capacity, significant acid inputs to the MSW IBA are required to reach this pH, which are improbable in the environment. Wood chip additions increase leachate's dissolved organic carbon (DOC) and reduce pH, but had minimal impact on metal-leaching behaviour. Synthetic plant exudate solutions minimally affect metal leaching at realistic concentrations, only enhancing leaching at ≥ 1500 mg l -1 DOC. This work supports MSW IBA's low-risk in specified civil engineering applications., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Portland cement concrete (PCC) is a major contributor to human-made CO2 emissions. To address this environmental impact, fly ash geopolymer concrete (FAGC) has emerged as a promising low-carbon alternative. This study establishes a robust compressive strength prediction model for FAGC and develops an optimal mixture design method to achieve target compressive strength with minimal CO2 emissions. To develop robust prediction models, comprehensive factors, including fly ash characteristics, mixture proportions, curing parameters, and specimen types, are considered, a large dataset comprising 1136 observations is created, and polynomial regression, genetic programming, and ensemble learning are employed. The ensemble learning model shows superior accuracy and generalization ability with an RMSE value of 1.81 MPa and an R2 value of 0.93 in the experimental validation set. Then, the study integrates the developed strength model with a life cycle assessment-based CO2 emissions model, formulating an optimal FAGC mixture design program. A case study validates the effectiveness of this program, demonstrating a 16.7% reduction in CO2 emissions for FAGC with a compressive strength of 50 MPa compared to traditional trial-and-error design. Moreover, compared to PCC, the developed FAGC achieves a substantial 60.3% reduction in CO2 emissions. This work provides engineers with tools for compressive strength prediction and low carbon optimization of FAGC, enabling rapid and highly accurate design of concrete with lower CO2 emissions and greater sustainability., Competing Interests: The authors have declared that no competing interests exist., (Copyright: © 2024 Jiang et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

As a result of firing pulverized coal in thermal power plants, enormous amounts of fly ash (FA) are produced as industrial waste. The release into the atmosphere and storage of this industrial waste remains one of the major environmental problems that threaten human health by contributing to air, water, and soil pollution. The recovery and reuse of FA in the construction industry is the only economic solution to the existing problem. In this study, the potential radiological risk caused by the usage of FA in concrete and cement production as a main component and its storage in landfill sites was evaluated for people and works by estimating radiological parameters (activity concentration and alpha index, annual effective doses, and the corresponding excess lifetime cancer risks) based on activity concentrations of terrestrial radionuclides in FA. Also, the radiological risk to the workers working in the FA landfill site was evaluated using the Residual Radioactivity Onsite 7.2 code. The average activity concentrations of terrestrial radionuclides in FA samples from the Tunçbilek lignite coal-fired thermal power plant at Kütahya province of Turkey were measured as 417, 156 and 454 Bq kg -1 for 226 Ra, 232 Th and 40 K, respectively. When using up to 35% by mass of FA in cement and concrete, the average values of the radiological parameters revealed that they were within the recommended safety limits. However, code estimations showed that a regular worker in FA storage would be exposed to a total effective dose rate greater than 3 mSv y -1 .

The analysis of the presence and content of substances that are toxic to aquatic life in waste is essential for classification of waste with regard to hazard property (HP) 14 'ecotoxic'. For the determination of HP14 classified copper (Cu) and zinc (Zn) compounds in various municipal solid waste incineration bottom ashes (IBA) and one fly ash (FA) from Germany we applied X-ray absorption near-edge structure (XANES) spectroscopy in combination with linear combination fitting. The analysis showed that approx. 50-70% of Cu in the IBA are Cu(I) compounds and elemental Cu(0), but these compounds were not equally distributed in the different IBA. In contrast, the majority (approx. 50-70%) of Zn in all IBA is elemental zinc, which originates from brass or other alloys and galvanized metals with a large content of zinc in the waste. The FA contain higher mass fraction on Zn and other toxic elements, but similar Cu and Zn species. Additional performed selective extraction at a pH of 4 with an organic acid of some IBA showed that the ecotoxic Zn fraction is mainly elemental zinc and zinc oxide. In contrast, for the ecotoxic Cu fraction within the IBA no specific compound could be identified. Furthermore, the XANES analysis showed that the HP14 properties of especially Cu in IBA is overestimated with current best-practice guidelines for sample processing for the current substance-related approach with the 0.1% cut-off rule for each substance. However, it should be considered whether it would not be better from an environmental point of view to take the ecotoxicologically leachable copper and zinc as a reference value., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

This study used the horizontal tubular heating furnace to explore the melting potential of circulating fluidized bed (CFB) incinerator fly ash and mechanical grate furnace (MGF) incinerator fly ash. The horizontal cyclone melting furnace was then built to explore further the feasibility of scale melting of MSWI fly ash. The melting characteristic temperature, amorphous content, and heavy metal leaching concentration characterized the melting potential and solidification effect of MSWI fly ash. The experimental results show that the amorphous content of CFB fly ash after melting is up to 92.37%, and the volatilization rate of heavy metals Zn, Pb, and Ni does not exceed 30%. MGF fly ash exhibits the "sintering into shells" phenomenon during heating, and the leaching concentrations of heavy metals Pb in the sintered products still exceed the standard limits. In addition, the volatilization rates of heavy metals Cu, Zn, Cd, Pb, Cr, and Ni in Slag II are above 50%, and the volatilization rate of Cr reaches 85%. So, slag's amorphous content also affects heavy metals' volatilization rate. The MSWI fly ash melting characteristic temperature decreases with the decrease of alkalinity value. When the alkalinity value drops to 0.6, the melting characteristic temperature reaches its lowest value. Mixing 80% CFB fly ash or 50% MGF bottom ash into MGF fly ash can significantly enhance the melting potential to reduce hazardous waste. When using the horizontal cyclone melting furnace to process MSWI fly ash on a large scale, MSWI fly ash achieves an excellent melting effect with an amorphous content of over 93% at the positions of the furnace middle section, inner tail cone, slag discharge outlet, and flue gas outlet. The fly ash particles are in motion in the melting furnace, so the particle size distribution affects the melting effect of MSWI fly ash., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Coal based thermal power plants contribute about ~ 72% of the power generation in India. Indian coal is of bituminous type, having a high ash content with 55-60% ash. Due to considerable environmental importance the collected fly ash has become a subject of worldwide interest in recent years. In the present study radon exhalation rate and the activity concentration of 226Ra, 232Th and 40K radionuclides in fly ash samples from Kasimpur Thermal Power Plant, Aligarh, Uttar Pradesh, India have been measured by 'Sealed Can technique' using LR-115 type II detectors and a low-level NaI (Tl)- based gamma-ray spectrometer, respectively. Radon exhalation rate has been found to vary from 57.1 ± 5.3 to 119.4 ± 7.7 mBq m-2 h-1 with an average value of 87.3 ± 5.8 mBq m-2 h-1. Activity concentration of 226Ra ranged from 20.0 ± 8.5 to 30.0 ± 9.7 Bq kg-1 with an average value 23.4 ± 9.0 Bq kg-1, 232Th ranged from 17.0 ± 9.9 to 69.0 ± 13.8 Bq kg-1 with an average value of 46.5 ± 12.1 Bq kg-1 and 40K ranged from 130.0 ± 7.2 to 332.0 ± 11.1 Bq kg-1 with an average value of 177.0 ± 8.1 Bq kg-1., (© The Author(s) 2024. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.)

The physical and chemical characteristics of fly ash has changed significantly under ultra-low emission system and the current leaching system is no longer suitable for high alkalinity fly ash. This work investigated the pH values and evolution of physical and chemical characteristics of fly ash from 24 typical municipal solid waste incineration plants in China. The pH value of the leaching solution obtained by HJ/T 300-2007 presented two different acid and alkali characteristics, where high and low alkalinity fly ash accounted for 54.17% and 45.83%, respectively. The alkali content in fly ash increased significantly after ultra-low emission standard, increasing by 18.24% compared with before the implementation of GB 18485-2014. The leaching behavior of high alkalinity fly ash showed the illusion that they could enter the landfill only by the addition of a small amount of chelating agent or even without stabilization treatment, and its long-term landfill risk is significant. The phase change of high alkalinity fly ash and pH value change of the leaching solution after carbonation were the key factors for the leaching concentration change of heavy metals. Therefore, it is recommended to improve the existing leaching system or conduct accelerated carbonization experiments to scientifically evaluate the long-term leaching characteristics of high alkalinity fly ash, and to reduce the risk of heavy metal release from high alkalinity FA after entering the landfill site., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

The current study introduces an innovative methodology by utilizing treated wastewater (TWW) from an effluent treatment plant as a washing agent to enhance the characteristics of incineration bottom ash (IBA). This approach addresses sustainability concerns and promotes the circular economy by reusing wastewater generated in municipal solid waste incineration facilities. Previous research has underscored the challenges of open IBA reuse due to elevated leaching of chlorides, sulfates, and trace metal(loid)s. Thus, the experimental setup explores various combinations of washing, with or without screening, to optimize the properties of soil-like material (SLM < 4.75 mm) and overall material (OM < 31.5 mm) fractions of IBA for unrestricted applications. Batch leaching tests were conducted on treated samples, and leaching characteristics were evaluated in accordance with regulatory standards, primarily the Dutch standard for unrestricted IBA reuse. The findings reveal that washing in isolation proves insufficient to enhance IBA properties; however, washing followed by screening, specifically for removing fines (<0.15 mm), proves effective in reducing contamination. The study identifies that multiple steps of washing and screening (with recirculation) process render OM and SLM fractions suitable for unrestricted reuse with a cumulative liquid-to-solid ratio of 6 L/kg and a total washing time of 15 min. The multi-step treatment was found effective in reducing sulfate contamination by 65-74 % and chloride contamination by 83-89 % in IBA fractions. This approach offers a promising solution for overcoming the limitations associated with IBA leaching, thereby promoting sustainable waste reuse practices., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

As a traditional method of waste treatment, municipal solid waste incineration (MSWI) has become one of the main methods of urban waste treatment. However, as a byproduct of MSWI, a large amount of MSWI bottom ash is not reused in current practice. This study innovatively posits MSWI bottom ash as an eco-friendly adsorbent rather than a pollutant, exploring its potential application as a permeable subgrade material. The results reveal that MSWI bottom ash exhibits promising properties to serve as a permeable subgrade material to achieve the permeability and improve the sustainability for subgrade. Due to the arrangement of its particles, it shows excellent performance in shear strength and permeability, which are comparable to or surpass those of sandy soils. The average pore width of 14.200 nm allows heavy metal substances to be encapsulated within the matrix, significantly reducing their leachability, thereby aligning with environmental friendliness standards. Its adsorption capacity is about 6.60 mg/g, and the adsorption capacity per volume is 3.66 times and 2.04 times that of fly ash and clay, respectively. The mechanism analysis shows that the adsorption process is monolayer heterogeneous adsorption. This paper presents a novel perspective on reusing MSWI bottom ash and provides evidence supporting its effective utilization as a permeable subgrade material, offering substantial environmental benefits through enhanced adsorption ability. Implications: Municipal solid waste incineration (MSWI) is a common method for municipal solid waste treatment, while the MSWI bottom ash is often not reused. This paper explored the explores the feasibility of using MSWI bottom ash as a permeable road base material. The results show that the particle arrangement enables excellent shear strength and permeability, comparable to sandy soil. It meets safety requirements for the leaching of heavy metals and acts as an adsorbent for pollutants leaching from permeable pavements. Furthermore, the mechanisms underlying these behaviors of MSWI were confirmed by microstructural and mineralogical analyses. These indicate that MSWI bottom ash has great potential as a permeable road base material. This paper provides a clear understanding of the physical, mechanical and environmental properties of MSWI bottom ash, which can promote its reuse in practice.

Considering that waste incineration fly ash is the main carrier of dioxins and can migrate over long distances in the atmosphere, it is of great significance to study the photochemical transformation behavior of dioxins on the surface of fly ash. In this work, 2-chlorodibenzo-p-dioxin (2-CDD) was selected to conduct a systematic photochemical study. The influence of various factors on the photodegradation of 2-CDD were first explored, and the results showed that small particle size of fly ash, low concentration of 2-CDD and appropriate level of humidity were more conducive to photodegradation, with the highest degradation percentage reaching 76%-84%. The components of fly ash (Zn (Ⅱ), Al (Ⅲ), Cu (Ⅱ) and SiO2) also had a certain promoting effect on the degradation of 2-CDD, which increases the degradation efficiency by 10%-20%, because they could act as effective photocatalysts to produce free radicals for reaction. With a higher total light exposure intensity, natural light environments led to a more complete degradation of 2-CDD than laboratory Xe lamp irradiation (90% degradation Vs. 79% degradation). Based on chemical probe and radical quenching experiment, hydroxyl radical also contributed to 2-CDD photodegradation on fly ash. A total of 16 intermediate products were detected by mass spectrometry analysis, and four initial reaction pathways of 2-CDD were speculated in the process, including dechlorination, ether bond cleavage, hydroxyl substitution, and hydroxyl addition. According to the results of density functional theory calculation, the reaction channels of ether bond cleavage and •OH attack were determined. The toxicity assessment software tool (TEST) was used to assess the toxicity and bioconcentration coefficient of reaction products, and it was found that the overall toxicity of the photodegradation products was reduced. This study would provide new insights into the environmental fate of dioxins during long-range atmospheric migration process., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Chlorinated benzenes (CBzs) are a group of organic pollutants, which have been industrially or unintentionally produced through various chemical and thermal processes. Studies on full congener profiles of CBzs in waste and environmental samples are relatively limited and not updated. In the present study, concentrations of 12 CBzs were determined in fly ash (FA) and bottom ash (BA) samples collected from one municipal waste incinerator (MWI) and one industrial waste incinerator (IWI) in northern Vietnam. Levels of Σ12CBzs were higher in bottom ash (median 25.3; range 1.59-45.7 ng/g) than in fly ash (median 7.30; range 1.04-30.0 ng/g). The CBz profiles were dominated by di- and tri-chlorinated congeners with the major congeners as 1,2,4-TCB, 1,2,3-TCB, 1,2-DCB, and 1,3-DCB. However, CBz profiles varied greatly between sample types and incinerators, implying differences in input materials, formation pathways, and pollutant behaviors. Incomplete combustion is possibly responsible for high levels of CBzs in industrial bottom ash. The emission factors of Σ12CBzs ranged from 21 to 600 µg/ton for fly ash and from 190 to 4570 µg/ton for bottom ash, resulting in annual emissions of about 6 and 3 g/year for the IWI and MWI, respectively. Our results suggest additional investigations on industrial emission and environmental occurrence of all 12 CBzs rather than solely focusing on regulated congeners like hexachlorobenzene and pentachlorobenzene., (© 2024. The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.)

Respirable fine-grained fly ash (RFA) is captured very inefficiently by existing air purification devices of power plant, leading to increasing concerns regarding their migration and subsequent interaction with body due to fine particle size and its complex toxic composition. Trace elements of RFA in three groups with five different sizes between 8-13 µm were analyzed in terms of available concentration, speciation and risk effects. The concentration, pollution level and ecological risk level of elements in RFA were related to particle sizes. Chronic non-carcinogenic effect risk (NER) and carcinogenic effect risk (CER) were negatively correlated with particle size. The individual weight of exposed subjects, corresponding trace elements concentration and ingestion rate in RFA were three significant variables influencing CER. NER and CER had a tenfold exaggerated effect when calculated using total element concentration of RFA. In addition to individual differences and exposure conditions, trace element properties, speciation and available concentration were the dominant factor responsible for ecological and environmental effects of trace elements in RFA, following the order As>Ni, Mn>Cr>Pb>Cu>Zn. Results of this work highlight the effects and differences of trace elements in RFA on ecology and health, and provide a basis for further pollution control and human health warning., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

This study investigates a circulating fluidised bed (CFB) incineration plant to examine the concentrations and fingerprints of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), and biphenyls (PCBs) at five locations downstream of the post-combustion zone. Sampling encompassed both flue gas and ash, spanning from the high-temperature superheater to the outlet of the baghouse filter, thus covering a wide range of flue gas temperatures. The analysis reveals a continuous increase in PCDD/F and PCB concentrations in the flue gas from the superheater to the inlet of the air pollution control system (APCS). The maximum concentrations observed were 75.8 ng/Nm 3 for PCDDs, 219 ng/Nm 3 for PCDFs, and 763 ng/Nm 3 for PCBs. These values represent 9.14, 11.5, and 6.37 times their respective concentrations at the outlet of the high-temperature superheater. Concurrently, the levels of PCDD/Fs and dioxin-like PCBs (dl-PCBs) in the ash steadily increased along the cooling path of the flue gas within the plant. Comparing dl-PCBs to the total amount of 209 PCB congeners, it was evident that dl-PCBs exhibited a trend more akin to that of PCDD/Fs. A robust linear correlation was observed between dl-PCBs and PCDD/Fs (R 2  = 0.99, p < 0.001), surpassing that between PCBs and PCDD/Fs (R 2  = 0.92, p < 0.01), suggesting that dl-PCBs share closer formation pathways with PCDD/Fs. Additionally, elemental composition analysis of fly ash samples aimed to explore potential links between fly ash characteristics and PCDD/F and PCB formation. The Cl/S ratio increased from 1.58 to 5.13 with decreasing flue gas temperature. Principal component analysis (PCA) was employed to visualise the concentrations of PCDD/Fs and PCBs in the flue gas alongside elemental contents in the fly ash. With the exception of PCBs in ash, all other PCDD/Fs and PCBs in fly ash exhibited positive correlations with both carbon (C) and chlorine (Cl). Furthermore, a positive relationship between C/Cl and PCDD/Fs-PCBs in fly ash implies that fly ash serves as the primary reaction surface for dioxin generation during low-temperature heterogeneous catalytic reactions., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Heavy metal pollutants such as Hg, As, Pb, Cr, and Cd emitted from coal and waste combustion have received widespread attention. In this study, we systematically investigated the emission characteristics of heavy metals in waste incineration and coal-fired flue gases, focused on testing the removal effect of self-made cold electrode electrostatic precipitator (CE-ESP) on heavy metals in flue gas, and made a comparative analysis with the existing air pollution control devices (APCDs). Test results from waste incineration power plant showed that each APCD showed a certain effect on the removal of heavy metals in condensable particulate matter (CPM), with an average removal efficiency of bag filter was 86%, but its effect on Hg removal was slightly worse. Under the coupled field with electrified cold electrode plate operation mode, the average removal efficiency of CE-ESP on heavy metals in CPM was as high as 93%, including 76% for Hg. The removal efficiency of heavy metals (especially Hg) in CPM increased with the increase of flue gas temperature difference between inlet and outlet of CE-ESP. Test results from this coal-fired power plant showed that heavy metals were enriched in fly ash to a higher degree than in slag, the synergistic control of heavy metals in submicron particulate matter by the dust remover was not obvious, and there was a significant correlation between each heavy metal emission factor and its content in coal. Under the temperature field with non-electric cold electrode plate operation mode, the overall effect of CE-ESP on the removal of gaseous heavy metals was better than that of particulate heavy metals. Under the conventional electric field operation mode, CE-ESP was less effective in removing particulate Cr and gaseous Hg 0 . Under the coupled field with electrified cold electrode plate operation mode, the average removal efficiencies of CE-ESP for particulate and gaseous heavy metals were 82.37% and 76.16%, respectively., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Nutrients are vital ingredients to boost plant health. The availability of nutrients is limited in fly ash (FA) waste to properly implement phytoremediation. The research explored the integration of microbes and treated wastewater irrigation in phytoremediation to provide the necessary nutrients for plant growth in fly ash-amended soils. The Box-Behnken method was used to design the experimental layout for the pot study. Response surface methodology (RSM) was applied as the optimization approach to model predictions for nutrient accumulation. The implemented pot study attained the highest morphological indicators with a plastochron index of 33.40, an absolute growth rate of 2.63 cm/day, and a leaf area of 2681.68 cm 2 and attained maximum biomass of 24.91 g for the treatments that included a mid-range of the variables. The combination of FA 14.98%, microbial dose 4.07 mL, and treated wastewater as the irrigation source was found to be the optimized combination for nitrogen and phosphorus accumulation of 212.4 and 8.867 mg/L., (© 2024. The Author(s), under exclusive licence to Springer Nature Switzerland AG.)

Although coal ashes (CA) can be converted into an eco-friendly product through vermicomposting, the utility of vermiconverted CA in agriculture still needs to be explored. Therefore, the feasibility of vermicomposted tea industry coal ash (VCA) as an alternative nutrient source for cabbage (Brassica oleracea, var. Capitata) production was evaluated through an on-field experiment in alluvial soil. Two types of vermicomposts were prepared using Eisenia fetida (VCA E ) and Lampito mauritii (VCA L ) and were applied in different combinations with chemical fertilizers. The results revealed a significant increase in nutrient availability (nitrogen, phosphorus, and potassium) in the soil treated with VCA, alongside a concurrent build-up of soil organic carbon stocks, activation of microbial growth, and enhanced soil enzyme activity. Additionally, VCA application substantially reduced toxic metals in the soil, thereby improving soil health and promoting the uptake of essential nutrients (nitrogen, phosphorus, potassium, iron, manganese, copper, and zinc) in cabbage. VCA application reduced the bioaccumulation of potentially toxic metals (chromium, lead, and cadmium) from coal ash, ensuring safer food production. Notably, a 25 % substitution of chemical fertilizers with VCA and farmyard manure (FYM) led to a two-fold increase in the growth and productivity of cabbage. The economic assessment also indicated that large-scale and sustainable recycling of toxic tea industry coal ash in agriculture is feasible. Hence, by integrating VCA-based nutrient management into agricultural practices, developing nations can take significant strides toward achieving circular economy objectives while addressing environmental challenges associated with CA disposal., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier B.V. All rights reserved.)

Background: Coal and coal ash present inorganic elements associated with negative impacts on environment and human health. The objective of this study was to compare the toxicity of coal and coal ash from a power plant, assess their inorganic components, and investigate the biological impacts and potential mechanisms through in vitro and in vivo testing., Methods: Particle-Induced X-ray Emission method was used to quantify inorganic elements and the toxicity was evaluated in Caenorhabditis elegans and Daphnia magna in acute and chronic procedures. The genotoxic potential was assessed using alkaline and FPG-modified Comet assay in HepG2 cells and mutagenicity was evaluated using Salmonella/microsome assay in TA97a, TA100, and TA102 strains., Results: Inorganic elements such as aluminum (Al) and chromium (Cr) were detected at higher concentrations in coal ash compared to coal. These elements were found to be associated with increased toxicity of coal ash in both Caenorhabditis elegans and Daphnia magna. Coal and coal ash did not induce gene mutations, but showed genotoxic effects in HepG2 cells, which were increased using the FPG enzyme, indicating DNA oxidative damage., Conclusions: The combined findings from bioassays using C. elegans and D. magna support the higher toxicity of coal ash, which can be attributed to its elevated levels of inorganic elements. The genotoxicity observed in HepG2 cells confirms these results. This study highlights the need for continuous monitoring in areas affected by environmental degradation caused by coal power plants. Additionally, the analysis reveals significantly higher concentrations of various inorganic elements in coal ash compared to coal, providing insight into the specific elemental composition contributing to its increased toxicity., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier GmbH. All rights reserved.)

The demand for production of cements is ever increasing to meet the infrastructure development globally. The energy and emission factors available for cements in most of the life cycle assessment (LCA) databases may not exactly suit for all the geographical locations. The main challenge in Indian scenario is the absence of database for LCA study. This study attempts to develop the energy and emission factors for the manufacturing of cements in Indian context. In the present study, five different cement manufacturing plants located in north, south, east, west and central zones of India are considered to assess the energy dissipation and carbon dioxide emission involved during the production of ordinary Portland cement (OPC). Most of the data is collected from the field, so that the energy and emission factors determined will be suitable for the zonal study. The study is then extended to assess the energy consumption and carbon dioxide emission for three blended cements, viz. Portland Pozzolan cement (PPC), Portland slag cement (PSC) and composite cement (CC) with permissible known replacement levels of fly ash, granulated blast furnace slag and both fly ash and slag, respectively. The average energy use and carbon emission is found to be on higher side in India by 15.14% and 12.64%, respectively, compared to other countries in manufacturing of cements. An average energy consumption in manufacturing of PPC, PSC and CC is found to be respectively 24.5%, 35.3% and 43.13% less compared to that of OPC. The CO 2 emission intensity for OPC is found to vary between 893 and 940 kg/tonne of cement from five different zones, and an average of respectively 24.8%, 40.97% and 47.18% lower CO 2 emission was observed from PPC, PSC and CC compared to OPC. From the inventory results, CC has proven to be a more sustainable cement with low energy consumption and lower CO 2 emission compared to other cements., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Coal fly ash (CFA), a byproduct of coal combustion, is a hazardous industrial solid waste. Its excessive global production, coupled with improper disposal practices, insufficient utilization and limited awareness of its inherent hazards, poses a significant threat to both ecological environment and human health. Based on the physicochemical properties of CFA and its leachates, we elucidate the forms of CFA and potential pathways for its entry into the human body, as well as the leaching behavior, maximum tolerance and biological half-life of toxic elements present in CFA. Furthermore, we provide an overview of current strategies and methods for mitigating the leaching of these harmful elements from CFA. Moreover, we systemically summarize toxic effect of CFA on organisms across various tiers of complexity, analyze epidemiological findings concerning the human health implications resulting from CFA exposure, and delve into the biotoxicological mechanisms of CFA and its leachates at cellular and molecular levels. This review aims to enhance understanding of the potential toxicity of CFA, thereby promoting increased public awareness regarding the disposal and management of this industrial waste., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Inc. All rights reserved.)

Large amount of coal ash is produced as industrial waste during the electricity generation through the combustion of lignite. Toxic elements arsenic exists in the coal ash, which hinders the subsequent recycling processes. Moreover, coal ash could be recycled further to retrieve scattered metals germanium and tungsten. It is believed that traditional recycling methods present barriers to scaled application, especially serious secondary pollution, such as toxic residue and waste liquid. In this work, a novel sequential vacuum distillation with disulphide method is proposed to separate arsenic, germanium and tungsten from coal ash. First, arsenic can be volatilized completely out of the reaction system at temperatures below 550 °C. Subsequently, Ge and W volatilized in the form of sulfide in the presence of Na 2 S 2 O 3 . The optimal condition was 1050 °C, the mass ratio of 0.6 with reaction a pressure of 1 Pa and a time duration of 120 min demonstrated the best evaporation ratio. For coal fly ash, chemical species As 2 S 3 , GeS, and WO x (x < 3)/WS 2 were the main condensed products. For coal bottom ash, As 2 S 3 , GeS, and WO 3 /WS 2 were dominant chemical components. Mechanisms for the process of release and evaporation of As, Ge, and W from coal ash, vacuum reaction, evaporation, and condensation were analyzed. In summary, the vacuum distillation method deserves to be further developed as it provides an eco-friendly method to recycle coal ash., Competing Interests: Declaration of competing interest The authors declare that they have no competing financial interests., (Copyright © 2023. Published by Elsevier Ltd.)

Coal ash (CA) is an industrial waste product that has been shown to contain several neurotoxic constituents such as cadmium, selenium, mercury, lead, and arsenic. Contaminant-laced leachates enter the environment via seepage, runoff, permitted discharge, or accidental spills from CA storage ponds or landfills which may pose a risk to wildlife residing in receiving waterways. In this study, we assessed 1) the presence and concentration of thirteen trace elements (Al, Ca, Mg, Cr, Cd, As, Se, Pb, Cu, Zn, Mn, Fe, B) in surface water and sediment grab samples using ICP-OES, 2) the temporal variability of trace elements using Pb-210 dated sediment core samples, 3) differences in species diversity using environmental DNA (eDNA) analyses, and 4) the presence and concentration of trace metals in banded killifish (Fundulus diaphanus) epaxial muscle tissue collected from waterways surrounding the Possum Point Power Station (Stafford, VA). Results showed the highest concentrations of As, Cd, Cr, Cu, Fe, Mg, Se, Zn, and B in Quantico Creek (QC) adjacent to the coal ash ponds and elevated average cadmium and zinc concentrations compared to both upstream and downstream locations along the Potomac River. Sediment core profiles and Pb-210 analyses showed historical enrichment of several trace elements in QC beginning after the commissioning of the power plant in 1948. When compared to upstream and downstream sites, species diversity was drastically reduced in Quantico Creek based on eDNA identification. Muscle tissues of banded killifish collected in Quantico Creek displayed increased Al, Cd, and Zn concentrations compared to upstream and downstream sites. Collectively, our results demonstrate the potential impacts of coal ash landfills on aquatic ecosystems and suggest that further research is needed to fully inform risk assessment and remediation efforts., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

The stabilization/solidification (S/S) method is one of the most effective remediation techniques for treating contaminated soils. Several stabilizers, mostly the cementitious materials, have been used for the S/S treatment. In this paper, the feasibility of utilizing fuel fly ash (FFA) as a partial replacement of ordinary Portland cement (OPC) for the S/S treatment of marl soil contaminated with heavy metals was investigated. Two industrial waste materials, namely steel and electroplating wastes, were used to synthetically contaminate the marl soil. The stabilizers comprising of OPC and FFA were mixed with the contaminated soil at different dosages ranging from 10 to 40%, by mass, and a total of 48 S/S-treated soil mixtures were prepared. A series of experiments, including density, porosity, permeability, unconfined compressive strength (UCS), and toxicity characteristics leaching procedure (TCLP), were carried out on the soil mixtures to evaluate the efficiency of the proposed S/S treatment. Test results showed that the incorporation of FFA at higher volumes reduced the density and increased the porosity and permeability of the treated mixtures. Although FFA addition resulted in reducing the UCS values by an average of 46%, and this reduction was more significant at higher FFA percentages, the UCS values of all mixtures were more than 0.35 MPa (350 kPa), which passed the minimum requirements set by USEPA. In addition, the metal immobilization ability of the proposed treatment was confirmed by the TCLP analysis. As compared to the negative effect of the contamination of the soil by the electroplating waste, the contamination of the soil by steel waste had a higher negative effect. The results of this study would contribute in selecting an environment-friendly treatment of the contaminated soils using industrial waste materials, such as FFA, as a partial replacement of OPC. Nevertheless, the present study is an initial attempt to explore the possibility of utilizing FFA as a partial replacement of OPC in S/S treatment of marl soil contaminated with heavy metals. It is recommended to conduct another study in future including analysis of the treated soil mixtures using XRD, SEM, and FTIR techniques to better understand the stabilization/solidification mechanism and its implications on the test results., (© 2023. The Author(s), under exclusive licence to Springer Nature Switzerland AG.)

Fly ash application to the soil at lower doses with organic substrates has been advocated by researchers due to its beneficial soil ameliorative properties. But its xenobiotic effects in presence of vermicompost have not yet been studied fully. The hypothesis of the present study was to ascertain the ameliorative effects of fly ash and vermicompost amendment on the soil nematode and earthworm count and change in the soil carbon pool of the rice nursery. The native soil, fly ash, and vermicompost at 0%, 20%, 40%, 60%, 80%, and 100% combinations (by weight) in triplicate were investigated under a factorial complete randomized design. The fly ash affected the earthworm survivability to an extent that the earthworms could not survive in fly ash of concentration greater than 20%. On the contrary, the concentration of vermicompost positively influenced the earthworm and nematode count in the rice rhizosphere. The population of nematodes viz. Rhabditis terricola and Dorylaimids in the rhizosphere of rice nursery was positively linked with the vermicompost concentration, while fly ash had antagonistic effects. The absence of nematodes and earthworms at a higher concentration of fly ash could be linked to the xenobiotic effects of fly ash. However, on mild addition of fly ash and vermicompost (20% each) to the native soil, the carbon stock increased positively to the maximum extent due to the larger surface area of fly ash and its xenobiotic effects limiting respirational carbon loss., (© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Primordial radionuclides can be found in all environmental compartments. Since coal-fired power plants (CFPP) can be a source of additional radionuclide contamination because coal contains natural radioactive isotopes such as 238 U ( 226 Ra) and 232 Th. This study investigated the impact of such possible radionuclide contamination from former heavy industrial activities, namely a former local coal-fired power plant, in urban soils and attic dust in Salgótarján, Hungary. Even today, industrial by-products, e.g., coal ash, in this city represent significant threat to its residents. A total of 36 attic dust samples (family houses, kindergartens, churches and blockhouses) were collected and 19 urban soil samples (playgrounds, kindergartens, parks and others) were selected no further than 500 m from the corresponding attic dust sampling sites. Additionally, a coal ash and a brown forest soil sample were also collected to differentiate between the anthropogenic and geogenic sources in the residential area. The sampled houses, built between 1890 and 1990, are considered to be representative sampling sites for long-term accumulations of attic dust. The mean values of the total U, Th and Cs (mg kg -1 ) concentrations as well as those of K (m/m %) in attic dust and urban soil samples are 2.4, 3.6, 1.7 and 0.6 and 1.1, 4.4, 1.2 and 0.3, respectively, measured using ICP-MS. The mean activity concentrations of 226 Ra, 232 Th, 40 K and 137 Cs in attic dust and urban soil samples are 43.3, 34.0, 534.4 and 88.5 and 25.1, 32.8, 386.4 and 5.6 Bq kg -1 , respectively, by using a low-background iron chamber with a well-type HPGe and a n-type coaxial HPGe detector. The elemental compositions (U, Th) and activity concentrations ( 226 Ra, 232 Th) along with their abundances in coal ash from the CFPP increase in both studied media as the distance of the sampling sites from the CFPP decreases. Two outlier attic dust samples in particular show significantly high activity concentrations of 226 Ra: 145 and 143, of 232 Th: 83 and 94 Bq kg -1 , which can be considered as a proxy of unweathered coal ash. The calculated total absorbed gamma dose rate (D) and annual effective dose (E) received from urban soils indicate that the presence of the CFPP, coal ash cone and slag dumps does not cause an increase in the level of background radiation in Salgótarján. However, the concentrations of the studied radionuclides are much higher (except for 232 Th) and exhibit higher degree of variability in the samples of attic dustthan in those of urban soils. The study suggests that attic dust preserves the undisturbed 'fingerprints' of long-term atmospheric deposition thanks to its chemical and physical properties unlike urban soil., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier Ltd.. All rights reserved.)

In this study, the specific activities of 226 Ra, 232 Th and 40 K in the unfired construction materials (solid card bricks, 4-hole bricks, pavement bricks) containing fly ash and bottom ash from a coal-fired thermal power plant in Vietnam were measured using the low-level gamma-ray spectrometer with HPGe detector. Also, the 222 Rn concentrations in these materials were analyzed using RAD7 radon monitor and then radon mass exhalation rate and emanation fraction of these materials were calculated. The potential radiological hazards for residents living in the model room made of these materials were evaluated. The average specific activity of 226 Ra, 232 Th and 40 K were found as 67.7, 79.3 and 703.5 Bq kg -1 , respectively. The total annual effective dose (due to external gamma exposure and internal radon exposure for resident living in the CEN model room made of the unfired brick samples) was found as 0.9 mSv y -1 which is lower than the worldwide average dose of 2.4 mSv y -1 . Calculations from ResRad-Build code showed that the doses due to radon exposure account for from 62.3% (at the first year) to 98.8% (at the next 30 years) of the total gamma and radon dose. Under low air exchange to the outside environment, from the 6th year onwards, the total dose may exceed the average dose value from natural radiation exposure sources., (© 2023. The Author(s), under exclusive licence to Springer Nature B.V.)

Nuclear industrial archaeology utilises radiation mapping and characterisation technologies to gain an insight into the radiological footprint of industrial heritage sites. Increased concentrations of naturally occurring radioactive materials at legacy mine sites are the result of elemental enrichment during coal mining and subsequent combustion. Public safety is of concern around these sites, and therefore, an increased understanding of their associated hazard is essential. Using coincident laser scanning and gamma detection technologies, this study sought to assess the radiological legacy of a coal mine located in Bristol, UK. From this, we can increase our understanding of the residual footprints associated with the local coal mining industry. Samples taken from inside the site were characterised using high resolution gamma spectrometry, wherein the radionuclide content and activities of samples were then quantified. An area of elevated low-level radioactivity was observed at and around buildings believed to belong to the colliery, while Th, U, and K are confirmed at the site from photopeak's of daughter radionuclides. Activities of the radionuclides K-40, U-238, and Th-232 were further quantified during subsequent laboratory analysis. Results highlight an enrichment of naturally occurring radionuclides when compared with global averages for unburned coal. Employing these techniques at further legacy sites would enable an increased understanding of the lasting traces of the coal mining industry, with a focus on NORM enrichment in residual fly ash., Competing Interests: Declaration of competing interest The authors declare no conflict of interest, financial or otherwise. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results., (Copyright © 2023 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Abstract Land application of coal ash is considered an environmentally friendly option to improve soil quality, but limited information exists on metal bioavailability and phytotoxicity of coal ash to sensitive plant species such as lettuce (Lactuca sativa L.). Germination and pot bioassay experiments were conducted at six coal application rates (0% (control), 5%, 15%, 25%, 50% and 75% v/v) to investigate the hypothesis that, coal ash will have a hormetic effect on germination, growth, metal uptake and biomass yield of lettuce, characterized by stimulatory and phytotoxicity effects at low and high application rates, respectively. Total concentrations (mg/kg) of metals in coal ash spanned several orders of magnitude, and decreased in the order: Fe (5150.5), Mn (326.0), Zn (102.6), Cu (94.7), Ni (74.7) and Pb (11.6). Bioavailable concentrations of metals were very low (0.0–14.1 mg/kg), accounting for less than 2% of the total concentrations. Coal ash had no significant effect on germination indices, but had hormetic effects on radicle elongation, evidenced by stimulatory and phytotoxicity effects at low (5–25%) and high (50–75%) application rates, respectively. Coal ash application at 50% and 75% significantly (p < 0.05) reduced lettuce growth and edible biomass yield, but lower application rates (5–25%) were similar to the unamended soil (control). Fe, Mn, Zn, Cu and Ni bioavailability and plant uptake generally decreased with increasing coal ash application rates particularly at 50% and 75%. Soil pH significantly increased (p < 0.05) from 6.5 for the control to about 8 for 75% coal ash, while electrical conductivity (EC) increased by 2–7 times to about 0.9 and 1.5 dS/m at 50% and 75% coal ash, respectively. Significant inverse linear relationship (p < 0.05; r2 = 0.80) were observed between edible and total biomass yields and EC, suggesting that increased salinity at high coal ash application rates could account for reduced growth and biomass. Partial elemental balances showed that plant uptake of metals was very low, accounting for just less than 2% of the bioavailable concentrations, while the bulk of the metals (98–99%) remained in the soil. In conclusion, the current findings show that coal ash may have hormetic and phytotoxic effects on sensitive plant species, an observation contrary to the bulk of earlier literature documenting beneficial effects of coal ash application to soils. Long-term field studies are required to confirm the current findings based on laboratory and pot bioassay experiments. Highlights • The phytotoxicity of coal ash (CA) used as a soil amendment on lettuce was studied. • CA had no effect on germination, but had a hormetic effect on radicle elongation. • CA reduced the bioavailability of metals, but increased soil pH and salinity. • CA significantly (p < 0.05) reduced metal uptake, growth and biomass of lettuce. • Biomass yield and electrical conductivity were inversely related (p < 0.05; r2 = 0.8). [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • Five Artificial Intelligence (AI) models have been implemented and evaluated. • Ash and combustible recovery of coal, going through flotation, have been predicted. • Mamdani Fuzzy Logic (MFL) model gives the best performance. Abstract In this study, five different machine learning (ML) and artificial intelligence (AI) models: random forest (RF), artificial neural networks (ANN), the adaptive neuro-fuzzy inference system (ANFIS), Mamdani fuzzy logic (MFL) and a hybrid neural fuzzy inference system (HyFIS) were employed to predict the flotation behavior of fine high ash coal in the presence of a novel "hybrid" ash depressant consisting of polyacrylamide chains grafted onto aluminium hydroxide nanoparticles: Al(OH) 3 -PAM (Al-PAM). A total of 51 flotation tests were conducted on coal samples with 38% ash-content and a P 80 of approximately 49 μm. Different influencing variables of coal flotation including polymer dosage, pH, polymer conditioning time, sodium metasilicate dosage (commercial dispersant), and the impeller speed were used as inputs for the models. The combustible recovery and ash content of coal reported to the concentrate were used as response variables (outputs). For AI model development, 80% of the total data was used for training phase and 20% was used for testing phase. Coefficient of determination (R2) and root-mean-square error (RMSE) were used as performance indicators of the models. The MFL model showed the best accuracy for the prediction of the combustible recoveries and the froth ash contents for this specific feed. However, in case of any significant change in the characteristics of the feed, these models would have to be re-trained using the data obtained through further physical experimentation and/or process model simulations. Moreover as these models are trained on laboratory scale data, these are only good for the predictions at laboratory scale. [ABSTRACT FROM AUTHOR]

Abstract In this study, laser-induced breakdown spectroscopy (LIBS) was applied for the qualitative elemental analysis of coal ash. The spectrum of the ordinary coal ash indicated that coal ash contains elements of Al, Fe, Cu, Ca, Mn, Ti and so on. Sulfates produced by the reaction of metal oxides in coal ash with the acid gases in the atmosphere are the main causes of haze-fog formation. To simulate the haze, eight solutions with different Pb concentrations were prepared and coal ash samples were soaked in solutions and then dried thoroughly. The spectra were obtained from these contaminated coal ash samples with the LIBS technique. To accurately identify the spectral lines of Pb in the spectrum, the spectrum of pure Pb were selected as a reference and the spectral lines of Pb were determined. At the same time, an internal standard method was used to quantitatively analyze the value of the component of Pb/Al with a calibration curve that had a linear correlation coefficient (R2) of 0.98648, which indicates rough estimation of Pb content can be achieved by the intensity of Pb in the spectrum. The results of the experiments show that LIBS technique can be employed for the rapid detection and analysis of metal elements in coal ash and provide a brand-new method for the detection of atmospheric environment based on the content of Pb. [ABSTRACT FROM AUTHOR]

Small-scale Solid Waste Thermal Treatment (SSWTT) is prevalent in remote Chinese locations. However, the ecological threats associated with heavy metals in resultant bottom ash remain undefined. This research study scrutinized such ash from eight differing sites, assessing heavy metal content, chemical form, and leaching toxicity. Most bottom ash samples met soil contamination standards for development land (GB36600-2018). However, levels of As, Cd, Cr, Cu, Ni, Pb, and Zn in some samples exceeded agricultural land standards GB15618-2018) by 1591%, 64,478%, 1880%, 3886%, 963%, 1110%, and 2011% respectively. Additionally, the As and Cd contents surpassed the construction land control limit value by 383% and 13% respectively. The mean values of the combined oxidizable and residual fraction (F3 + F4) for each heavy metal in all samples exceeded 65%, with Cr, Cu, Ni, and Pb reaching over 95%. All sample leaching concentrations, obtained via the HJ/T 299 procedure, were less than limits set by the identification standards for hazardous wastes (GB5085.3-2007). However, only the leaching concentrations of three samples via the leaching procedure HJ/T 300 met the "Solid Waste Landfill Pollution Control Standard" (GB 16889-2008). The results indicate that the location and type of SSWTT equipment play a crucial role in determining an appropriate solution for bottom ash management., (© 2023. The Author(s), under exclusive licence to Springer Nature B.V.)

Backfill mining can effectively alleviate the problems of surface collapse and ecological water pollution, in which the mechanical properties of backfill materials, including coal gangue and coal fly ash, have a decisive role in the effect of filling mining. In this study, we analyze the permeability characteristics of coal gangue filler through a set of homemade percolation test systems and introduce fractal characteristics to investigate the key factors affecting percolation in complex pores of broken coal gangue. The results indicate that the fractal dimensions of crushed coal gangue particles show an increasing trend with increasing axial loading and that the variation range is from 2.15647 to 2.58933. The coal fly ash concentration has a positive relationship with the acceleration factor. The permeability of crushed coal gangue follows a hierarchical distribution law and the permeability changes in the magnitude range of 10 -11  ~ 10 -9 m 2 . The fractal dimension is inversely related to the permeability of crushed coal gangue. The experimental results show that the coal gangue will be further crushed and that adding a certain concentration of coal fly ash can achieve a better water barrier, which provides theoretical support and engineering significance for the stability analysis of geological engineering and backfill mining technology., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The tanning sludge (TS) and other tanning solid wastes are produced in significant quantities by the leather industry. To evaluate the combustion properties, acid gaseous pollutant conversion, and ash management, co-firing of TS with various wastes was investigated in a bubbling fluidized bed. TG-FTIR test indicated that tanning solid wastes had superior combustion properties and include more gaseous pollutants than TS. The leather mixed solid waste (LMSW) formed by mixing had better fuel characteristics than TS. The conversion rates of SO 2 and HCl of LMSW incineration were 67% and 40%, respectively. The co-combustion of TS and solid wastes reduces the conversion rate of acid gas. Increasing the proportion of high-inorganic chlorine raw material could further reduce the conversion rate and increase the ash fusion temperature appropriately. Because ash and slag were primarily composed of Ca and Fe elements, the addition of calcium carbonate (CaCO 3 ) can increase ash melting point while reducing acid gas emissions. When CaCO 3 was added at a calcium to sulfur (Ca/S) ratio of 2, the acid gas emission was reduced by more than 80% and the softening temperature was raised by 90 °C. When Ca/S is greater than 2, the economics of adding CaCO 3 decreased., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Energy-harnessing sources significantly influence a country's infrastructure and economic development. Though nuclear and hydel power sources are used for energy harnessing, thermal sources are still the primary power source in India and contribute to 75% of the demand. Thermal power plants exploit large volumes of coal reserves. The combustion of coal leads to 30%-40% of waste ash residues such as Fly ash and Bottom ash. Though Fly ash finds greater applicability, pond ash poses a severe environmental hazard due to its large occupancy of terrain in ash dykes and lagoons. Many research efforts are underway to utilize pond ash in various structural and geotechnical infrastructure projects; however, there are still limitations and apprehensions about its properties and determination. The present study provides a detailed review of the morphological and chemical properties. Further, the geotechnical attributes of pond ash, including strength characteristics, consolidation parameters, and durability aspects, are critically reviewed for the probable application as fill material for backfill and many other applications. Based on the earlier research on pond ash, it could be comprehended that pond ash has wide property variability and finds compatibility with many other pozzolanic admixtures and, in this way, finds broader applicability in geotechnical projects. The way forwards could be a significant step towards cleaner and greener technology., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

A simple mixing-pressing followed by thermal curing and pyrolysis process was used to upcycle coal waste into high-value composites. Three coal wastes of different physicochemical properties were investigated. The hypothetical mechanisms of bonding between the coal particles and the preceramic polymer are presented. The textural properties of the coals indicated that the lowest volatile coal waste (PCD) had a dense structure. This limited the diffusion and reaction of the preceramic polymer with the coal waste during pyrolysis, thereby leading to low-quality composites. The water contact angles of the composites up to 104° imply hydrophobic surfaces, hence, no external coating might be required. Analysis of the carbon phase confirmed that the amorphous carbon structure is prevalent in the composites compared to the coal wastes. The dc volume resistivity of the composites in the range of 22 to 82 Ω-cm infers that the composites are unlikely to suffer electrostatic discharge, which makes them useful in creating self-heating building parts. The leached concentrations of heavy metal elements from the composites based on the end-of-life scenario were below the Toxicity Characteristic Leaching Procedure regulatory limits. Additionally, the release potential or mobility of the metals from the composites was not influenced by the pH of the eluants used. On the basis of the reported results, these carbon/ceramic composites show tremendous prospects as building materials due to these properties., (© 2023. The Author(s).)

In the current phase, the engineering and construction industry has successfully engaged in a challenge for consuming “sustainable, green and recycled products” in manufacturing of concrete. The utilization of Coal Bottom Ash (CBA) in concrete industry is one of the best feasible options to minimize the environmental concerns raised due to its presence. The use of CBA in manufacturing of concrete has been increased in last decade. Coal bottom ash has a potential to be used as concrete material in place of fine aggregates. The present investigation has focused on reviewing some of the fresh, mechanical and durability properties of Normally Vibrated Concrete (NVC) and Self-Compacting Concrete (SCC) made with incorporation of CBA as replacement of fine aggregates. Most of the studies have described that the use of CBA lowers the overall performance of NVC/SCC, whereas few of them have reported its successful use in attaining similar/better performance to that of the concretes made without incorporation of CBA. [ABSTRACT FROM AUTHOR]

Internationally, the demand for a variety of rare earth elements (REY/REY + Sc) (i.e. Sc, Y, La, Ce, Pr, Nd, Pm, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu) for use in modern electronic and related components is increasing. This demand has led to a need to expand extraction from alternative sources, such as coal and combustion ash. South Africa has extensive coal resources and generates a significant amount of coal ash. The aim of the study is to determine the levels of REY + Sc in three South African power station feed coals and their associated ash products (eight samples), with a consideration of the viability of commercial extraction of REY + Sc from these materials. The coal and ash samples were analysed using a variety of routine and advanced techniques, including petrography, Malvern particle size analysis, X-ray diffraction (XRD), inductively coupled plasma-mass spectrometry (ICP-MS), and instrumental neutron activation analysis (INAA). Total REY concentrations ranged from 95 to 149 ppm in the coal samples, and H– and M-type REY enrichment types were determined. Total REY concentrations ranged from 402 to 599 ppm in the ash samples, far higher than the average upper crustal values, and higher than global average hard coal ash values, but lower than REY-rich coal ashes recorded for various deposits globally. The INAA data are comparable to the ICP-MS data for most elements considered, and Sc was determined. Further investigations are required to confirm the potential of the Main Karoo Basin coal ash for economically viable REY extraction. [ABSTRACT FROM AUTHOR]

In entrained-flow gasification, solid fuel is brought in contact with oxygen and steam, yielding slagging conditions at temperatures of 1250–1800 °C. The process temperature cannot be chosen freely but is determined by the melting behavior of the coal ash. By blending different coals and fluxing agents, the ash fusion temperature can be lowered allowing operation at a lower reactor temperature and savings in oxygen. Since ash fusion behavior is not measurable online, it can be beneficial to use a quickly measured coal ash composition and estimate the ash fusion behavior instantly. In this work, >300 different coal samples from all over the world were investigated. This includes ash compositions determined from X-ray fluorescence (XRF) analysis and standard ash fusion behavior under reducing and oxidizing conditions. In a systematic approach, the ash components were limited to the most significant ones to optimize calculation time. The software ChemApp was used to calculate thermodynamic equilibrium based on FToxid and FactPS databases. The obtained results involve the temperatures at which 10 to 100% of the ash melt are liquid slag calculated in 10%-pts steps. According to the applied atmosphere, the obtained results have been statistically correlated to the experimentally determined fusion temperatures. In parallel, a neural network approach was tested to accomplish the same task. It was found that the hemispherical temperature correlates best to a liquid slag fraction of 85.0 wt% under reducing and 80.1 wt% under oxidizing conditions. The thermodynamic model is able to predict the hemispherical temperature under reducing conditions for 32% of the data while exclusion criteria defining the validity range have been formulated. The neural network model shows in average a higher accuracy of predicting ash fusion behavior from ash composition covering also temperatures of initial deformation and fluidity and appears as a suitable alternative to the thermodynamic calculation if sufficient data are available (i.e. covering the coal ash composition range of interest). [ABSTRACT FROM AUTHOR]

The use of coal fly ash (CFA) as raw material for the manufacture of two construction materials, fired clay bricks and silica-calcareous non-fired bricks, was investigated. Fired clay bricks were manufactured using a commercial clay and different waste ratios (0–50 wt%), moulded at 10 MPa and fired at 1000 ºC (4 h). Silica-calcareous non-fired bricks were prepared using two wastes as raw material: CFA and “geosilex”(G), a hidrated lime residue which comes entirely from acetylene industry waste. Different proportions CFA (80–30 wt%) – G (20–70 wt%) were investigated. Raw materials were moulded at 10 MPa and cured in water at room temperature during 28 days. The results indicated that the incorporation of up to 20 wt% of CFA produced fired clay bricks with physical and mechanical properties similar to control bricks without waste. However, additions of a higher amount (30–50 wt%) of residue resulted in a more pronounced decrease in mechanical properties (between 25–50%) due to an increase in open porosity. The technological characterization of the silica-calcareous non-fired bricks showed a reduction in the values of bulk density and water absorption when the coal fly ash content decreases. Silica-calcareous non-fired bricks containing between 40 and 60 wt% of CFA had the highest values of compressive strength in the range 46–43 MPa. These silica-calcareous non-fired bricks, 60CFA-40 G, 50CFA-50 G and 40CFA-60 G, presented the optimum amount of pozzolanic materials (SiO 2 and Al 2 O 3 ) in the coal fly ash and calcium hydroxide in the geosilex to give rise to the formation of calcium silicate hydrates and calcium aluminate hydrates, the phases responsible for the mechanical resistance increase of the construction materials. Therefore, CFA-clay fired bricks and silica-calcareous CFA-Geosilex non-fired bricks presented optimal technological properties that attain the quality standards. [ABSTRACT FROM AUTHOR]

The Israeli quarry industry produces 57 Mt of raw material and ∼4–6 Mt of associated sub-economical by-products annually. These sub-economical quarry fines are not used because production and transportation costs considerably exceed their retail value. Therefore these by-products, are stored in large piles of fine grain size particles, create environmental risks to their surrondings. This paper evaluates the possibility of mixing the sub-economical quarry by-products of two Israeli quarries with sub-economical Class F coal fly ash (<20 wt.% CaO) to form an economical aggregate sand substitute to be used as a concrete filler product. To study the feasibility of the aggregate as partial substitute to sand in concrete several analyses, including leaching experiements (EN12457-2), analytical techinques (SEM-EDX, ICP-MS, ICP-AES, and XRD), as well as an analysis of the mechanical and chemical properties of the concrete aggregate (strength, workability, and penetration) were performed. Scrubbing quarry waste with coal fly ash was found to be very effective for reducing the leaching rate of potentially harmful trace elements. In addition, adding fly ash with quarry fines as partial substitute to sand enhanced the performance of the concrete mixture and the properties of the fresh and harden concrete. [ABSTRACT FROM AUTHOR]

Low ash clean coal was produced from Indian coking coal through microwave irradiation or ultrasonication followed by solvent extraction in N-methyl-2-pyrollidone (NMP) containing smaller amount of Ethylenediamine (EDA) or Monoethanolamine (MEA). Pretreatment by ultrasonication followed by extraction with only NMP gave 10–15% higher clean coal yield of (56–58%) than extraction with only NMP (without pretreatment). Effect of using up to 10% EDA as cosolvent in NMP led to maximum clean coal yield. However use of EDA concentration beyond this showed decrease in clean coal yield and increase in ash contents. Clean coal yield increases because EDA is a strong polar solvent and strong base, which disrupts coal interactions and breaks bonds in coal by acid-base interactions. The extraction yield with and without pretreatment and microwave irradiation led to the enhancement in the yield of clean coal and was found to be in the range of 66–70% with microwave irradiation, which was 3–4% higher than without pretreatment. Clean coal Free Swelling Index (FSI) was improved by one unit. This was demonstrated at lab scale. Subsequently, this process was scaled up to 40 kg/batch coal mini-pilot plant. [ABSTRACT FROM AUTHOR]

Gasification has been deemed as the most promising method for the thermochemical conversion of Shanxi high ash coals, although the use of these high ash coals leads to high consumption of coal and oxygen, low syngas yield and cold gas efficiency. In order to improve gasification efficiency, it is necessary to reduce the ash content of these Shanxi high ash coals. In this work, three representative Shanxi high ash coals were floated with ZnCl 2 flotation agent to obtain floated coal samples with different ash contents. The mineral evolution during coal washing and its effect on ash fusion characteristics were thoroughly investigated. A radio frequency oxygen plasma furnace, X-ray diffraction (XRD) and SIROQUANT were used to analyze the variation of mineral compositions of the floated coals. Quartz (SiO 2 ), kaolinite (Al 2 (Si 2 O 5 )(OH) 4 ), calcite (CaCO 3 ), and tobelite (NH 4 Al 3 Si 3 O 10 (OH) 2 ) were main mineral which were found in Shanxi high ash coals, and the high contents of quartz and kaolinite led to high AFTs (ash fusion temperatures) of these coals. As mineral content decreased, the contents of quarts, kaolinite, and calcite in the floated coals were obviously lowered, and this resulted in the decrease of S/A (mass ratio of SiO 2 /Al 2 O 3 ) of the coal ashes. The ash fusion temperatures of Shanxi high ash coals were therefore significantly influenced by the extent of coal washing. Furthermore, the content of amorphous material in coals increased obviously with the decrease of ash content. These results have important implication in the selection of the appropriate coal washing procedure prior to gasification of these coals. [ABSTRACT FROM AUTHOR]

Coal gasification is widely used for chemical production as well as energy generation, and slag tapping process is crucial to entrained-flow coal gasification, before which particle deposition play an important role in slag formation. In order to investigate the slag tapping under special or abnormal operating conditions, the ash/slag particle deposition and ash/slag layer behavior characteristics have been studied based on a bench-scale impinging entrained-flow gasifier. High temperature endoscopy combined with high speed photography is applied to obtain images inside the gasifier and image processing techniques are used to distinguish the object from the high brightness background. The results show that an ash/slag deposition layer is formed under low operating temperature. In the case of particle deposition: High temperature particle (HTP) with medium size would slide on ash/slag layer after impacting, low temperature ash/slag on the deposition layer adheres on the particles and detach from the deposition layer together. HTPs with big size would attract low temperature ashes while travelling in gasifier space and ash/slag surface after impact, then form a low temperature particle (LTP) group with high temperature core and detach from the basic ash/slag layer. LTPs with big size and high space speed would impact and embed into the ash/slag deposition layer, then particle temperature rises while particle volume decreases. The embedded particles hardly detach from the basic layer. The low temperature ash/slag deposition layer would detach from the old slag layer on refractory wall, and the detachment of ash/slag layer is mainly classified into three typical patterns according to the behaviors of the detach process: detach after sliding pattern, detach after tilting and shaking pattern, detach after warping and fracturing pattern. Detachment after warping and fracturing is the commonest pattern of ash/slag deposits behavior that has been observed. Due to the huge volume of detached pieces, it could be the major source of slagging under abnormal operating condition. Under certain extreme conditions, slag tap hole would be blocked by the bridging of huge ash/slag deposits pieces and leads to overpressure of gasification chamber and slagging failure. In industrial applications, the results of this study would be the theoretical support for the suggested minimum load and suggested feeding period of the gasifier during the unique online pressurized continuous coal-water slurry feeding technique of the opposed multi-burner (OMB) gasification. [ABSTRACT FROM AUTHOR]

Circulating fluidized bed (CFB) with low operating temperatures may become an appropriate solution to the utilization of high-Na Zhundong coal. In this paper, one kind of Zhundong coal with 3.92% Na 2 O in coal ash was used as fuel, and its slagging and fouling characteristics at different air equivalence ratios (ERs) were systemically investigated in 0.4 t/d CFB test system to determine a better utilization scheme of Zhundong coal. The results show that ash-related problems still occurred when this high-Na coal was used in CFB, which was greatly influenced by ER. At the reducing atmosphere (ER < 1.0), slagging obviously occurred in the riser at ∼940 °C. Na-based species reacted with the SiO 2 -rich bed material to form low-melting-temperature sodium silicates (Na 2 O· n SiO 2 ). The formed sodium silicates covered bed material particles and increased their stickiness. These sticky particles agglomerated and adhered onto the high-temperature metal surfaces by adhesion force or inertial force, resulting in slagging. During slagging process, Ca, Mg and Fe acted as fluxing agents. This type slagging related to the SiO 2 -rich bed material might be reduced or even avoided via the replacement of the bed material. At the oxidizing atmosphere (ER > 1.0), fouling on tail heating surfaces at medium-low temperatures (607–735 °C) was the main ash-related problem. The released AAEM-based species were transported towards low-temperature surfaces by the mechanisms of diffusion, condensation and aggregation, or thermophoresis, resulting in a layered deposition. The inner layer of deposits with micron grain sizes, which was mainly composed of Na 2 SO 4 and K 2 SO 4 , played a key role at the initial deposition stage. Besides, two kinds of aggregated particles separately rich in alkali silicates and Ca-based species were also important for fouling. [ABSTRACT FROM AUTHOR]

The classification and identification of coal ash contributes to recycling and reuse of metallurgical waste. This work explores the combination of the laser-induced breakdown spectroscopy (LIBS) technique and independent component analysis-wavelet neural network (ICA-WNN) for the classification analysis of coal ash. A series of coal ash samples were compressed into pellets and prepared for LIBS measurements. At first, principal component analysis (PCA) was used to identify and remove abnormal spectra in order to optimize the training set for the WNN model. And then, ICA was employed to select and optimize input variables for the WNN model. The classification of coal ash was carried out by using the WNN model with optimized model parameters (the number of hidden neurons (NHN), the number of iterations (NI), the learning rate (LR) and the momentum) and input variables optimized by ICA. Under the optimized WNN model parameters, the coal ash samples for test sets were identified and classified by using WNN and artificial neural network (ANN) models, and the WNN model shows a better classification performance. It was confirmed that the LIBS technique coupled with the WNN method is a promising approach to achieve the online analysis and process control of the coal industry. [ABSTRACT FROM AUTHOR]

We recently showed that the selective extraction of aluminium from the amorphous phase of a South African ultrafine coal fly ash can be achieved via thermochemical treatment with ammonium sulphate for 1 h followed by aqueous dissolution, as an alternative to conventional hydrometallurgical processes. In this study, insight gained from the previous work was applied to investigate and compare total vs selective aluminium extraction efficiencies using ammonium sulphate or ammonium bisulphate either on its own, or as a mixture of the two salts as extracting agents during a 2 h thermal treatment process. The effects of (i) ash-to-extractant mass ratio and (ii) temperature during thermal treatment on extraction efficiency was investigated. While a maximum, but non-selective, recovery of 46.6% total aluminium was achieved using ammonium bisulphate at 400 °C, the most technically appropriate results for selective recovery yielded 37.3% aluminium, with only 0.3% silicon, 0.1% titanium and 3.9% iron having been co-extracted when using ammonium sulphate at a processing temperature of 600°C. Extraction of most of the calcium and magnesium could not be prevented. Using mixtures of ammonium salts as extracting agents during thermochemical treatment may however introduce technical difficulties on large scale. Our results indicate that any of the two ammonium salts could be used on their own during thermochemical treatment. Thermochemical treatment of coal fly ash using ammonium salts may therefore represent a promising technology for extracting aluminium from South African coal fly ash. [ABSTRACT FROM AUTHOR]

The solid waste known as fly ash, which is produced when coal is burned in thermal power plants, is sustainably used in agriculture. It is an excellent soil supplement for plant growth and development since it contains some desired nutrients (macro and micro), as well as being porous. The present study was done to evaluate the effect of different fly ash levels on Withania somnifera. The present study aimed to assess the impact of various fly ash (FA) concentrations on growth, yield, photosynthetic pigments, biochemical parameters, and cell viability of W. somnifera. The results showed that FA enhanced physical and chemical properties of soil like pH, electric conductivity, porosity, water-holding capacity, and nutrients. The low doses of FA-amended soil (15%) significantly increased the shoot length (36%), root length (24.5%), fresh weight of shoots and roots (107.8 and 50.6%), dry weight of shoots and roots (61.9 and 47.1%), number of fruits (70.4%), carotenoid (43%), total chlorophyll (44.3%), relative water content (109.3%), protein content (20.4%), proline content (110.3%), total phenols (116.1%), nitrogen (20.3%), phosphorus (16.9%), and potassium (26.4%). On the other hand, the higher doses, i.e., 25% of fly ash showed a negative effect on all the above parameters and induced oxidative stress by increasing lipid peroxidation (33.1%) and hydrogen peroxide (102.0%) and improving the activities of antioxidant enzymes and osmolytes. Compared to the control plants, the plants growing in soil enriched with 15 and 25% fly ash had larger stomata pores when examined using a scanning electron microscope. In addition, according to a confocal microscopic analysis of the roots of W. somnifera, higher fly ash concentrations caused membrane damage, as evidenced by an increase in the number of stained nuclei. Moreover, several functional groups and peaks of the biomolecules represented in the control and 15% of fly ash were alcohols, phenols, allenes, ketenes, isocynates, and hydrocarbons. Gas chromatography-mass spectrometry analysis of the methanol extract of W. somnifera leaves cultivated in soil amended with 15% fly ash shows the presence of 47 bioactive compounds. The most abundant compounds in the methanol extract were cis-9-hexadecenal (22.33%), n-hexadecanoic acid (9.68%), cinnamic acid (6.37%), glycidyl oleate (3.88%), nonanoic acid (3.48%), and pyranone (3.57%). The lower concentrations of FA (15%) can be used to enhance plant growth and lower the accumulation of FA that results in environmental pollution., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)