Search

Implant and a tooth supported dentures are avoided by dentists because of uneven distribution of occlusal loads between a stiffer implant and a more pliable tooth. The hypothesis was that a 3-point all-ceramic bridge supported on a natural second premolar tooth and a two-pieces typical implant bears safely mastication loads. The finite element analysis showed that the implant splinted by all-ceramic zirconium bridge with the second premolar was safe under lateral mastication load, but there was found an overload at wide zone of bone tissue around the implant under the load of 800 N. The patients can safely masticate, but comminution of hard food should be avoided and they should be instructed that after such an indiscretion they need to contact a dental professional, because, in spite of integrity of the prosthesis, the bone tissue around the implant may fail and there is a hazard of intrusion of the tooth.

The paper aims was assessing risks of mandible fractures consequent to impacts or sport accidents. The role of the structural stiffness of mandible, related to disocclusion state, was evaluated using the finite element method. It has been assumed, that the quasi-static stress field, due to distributed forces developed during accidents, could explain the common types of mandibular fractures. Mandibular condyles were supposed jammed in the maxillary fossae. The force of 700 N, simulating an impact on mandible, has been sequentially applied in three distinct areas: centrally, at canine zone and at the mandibular angle. Clinically most frequent fractures of mandible were recognized through the analysis of maximal principal stress/strain fields. It has been shown that mandibular fracture during accidents can be analyzed at satisfactory level using linear quasi-static models for designing protections. [ABSTRACT FROM AUTHOR]

Selective Laser Melting (SLM) is a modern manufacturing method with many applications in medicine, aerospace and automotive industries. SLM processed materials are characterized by good dimensional accuracy and properties comparable or superior to materials obtained by traditional processing methods. In this paper an SLM process was used to obtain 316L stainless steel parts. This paper presents the microstructure, chemical and phase composition, physicochemical and electrochemical properties of 12 groups of tested samples, differentiated by the SLM processing parameters. Based on the investigation, it can be inferred that the selection of the appropriate SLM parameters is very important to determined final material properties. The samples produced with the energy density E = 600 J/mm³ were observed to possess optimum properties - a homogeneous structure, density closest to the desired one, good wettability and pitting corrosion resistance. [ABSTRACT FROM AUTHOR]

The paper analyses the influence of chemical composition of silicone-based composites on their properties in the aspect of using them as long-term soft denture lining materials. Different concentrations of filler and methylhydrosiloxane-dimethylsiloxane copolymer were used. The filler was introduced into the composite with mechanical mixing combined with ultrasonic homogenization. Scanning electron microscopy was used to investigate the quality of filler dispersion. Shore A hardness, tensile strength, sorption, solubility and tensile bond strength to poly(methyl methacrylate) were measured. Tests show satisfactory results for some experimental composites, which met all the requirements for such materials. [ABSTRACT FROM AUTHOR]

The aim of the study was to evaluate the influence of different fillers on the chosen functional properties of experimental composites based on typical polymeric matrix, in order to understand the effect of different fillers on their properties and to develop a simple base composite for further investigations with experimental fillers, e.g. with antimicrobial properties. Previous experiments have been usually based on commercially available composites of unknown composition or compilation of monomers, without reinforcing fillers. Scanning electron microscopy was used to investigate the quality of fillers' dispersion, which was satisfying. Results showed significant differences between materials' diametral tensile strength (p = 0.0019), compressive strength (p < 0.0001), Vickers micro-hardness (p < 0.0001), flexural modules (p = 0.0018), and the degree of conversion (p < 0.0001), but flexural strength was not significantly different (p = 0.0583). Investigations indicated that no filler type had an especially positive impact on the mechanical properties, but reinforcement effect was achieved by proper compilation of silica nanofiller and variable glass fillers. Nanofiller decreased the degree of conversion. [ABSTRACT FROM AUTHOR]

The paper presents the effect of ZrO2 layer deposition by the ALD process on the physicochemical properties of cobalt-based alloys (Realloy C and EOS CoCr SP2) intended for application in prosthetic dentistry. The paper shows the results of the surface roughness measurements made by the AFM method as well as the wettability and free surface energy measurements. Additionally, potentiodynamic tests of pitting corrosion resistance and electrochemical impedance spectroscopy in a solution of artificial saliva were carried out. Tests were carried out on the samples in the initial state and after surface modification with the ZrO2 layer. Based on these results, the usefulness (e.g. enhancement of corrosion resistance and biocompatibility) of the proposed ZrO2 layer on the cobalt alloys was assessed. [ABSTRACT FROM AUTHOR]

The aim of this study was to assess the influence of summer temperatures on the milk content and technological properties for three different cow breeds. The experiment took place between June and August 2015. We observed 18 dairy cows, kept in identical conditions. We used cows of 3 breeds: Czech Fleckvieh (C), Holstein (H) and Ayrshire (A). Samples were taken weekly. The analyzed parameters were: total yield per observed period, milk content, density, active and titrable acidity, rennet coagulation time (RCT) and curd class quality. Average daily yield was 22.8 (A), 28.1 (H) and 24.4 (C) liters. All cows were at the same lactation (2nd). All breeds showed an increase (from 12.74% to 12.24%) in dry matter. Titrable acidity was significantly (P < 0.05) increasing and active acidity was decreasing for all three breeds. When it comes to technological properties Czech Fleckvieh and Holstein showed a decrease in RCT and curd quality, and Ayrshire showed an increase in both RCT and curd quality. This can point to the fact that, though these three breeds are different, some characteristics (dry matter, titrable and active acidity) of their production are affected by the high summer temperatures. RCT values indicate that Czech Fleckvieh is more adaptable to high temperatures.

This review examined the current state of knowledge on the modifications of commercial soft lining materials (SLMs) with a variety of antifungal compounds: (i) polyene antibiotics, including nystatin and amphotericin B, (ii) azole drugs, including fluconazole, itraconazole, clotrimazole, ketoconazole, and miconazole, and (iii) antiseptics, including chlorhexidine salts to give them anti- Candida albicans properties. The effect of such modifications on the SLMs' physical properties, such as drug release, water sorption, surface properties, bond strength, tensile strength, and hardness, was also analyzed. In effect, this study provided a unique compilation of research results obtained for numerous properties of SLM modified with antifungal compounds that differ in their chemical structure and mechanism of antifungal action. These results might also be useful for prosthetic dentistry, where SLMs are used to prevent and treat candidiasis, the most common disease among denture wearers.

Denture fractures are a common problem in dental practice, and their repair is considered a first option to restore their functional properties. However, the inter-material resistance may become compromised. Typically, the bond between these materials weakens. Therefore, various surface treatment methods may be considered to enhance their mechanical properties. Poly(methyl methacrylate) (PMMA) heat-polymerized resin (HPR) was used as the repaired material, cold-polymerized material (CPR) for the repairs, and different variants of alumina abrasive blasting (AB), methyl methacrylate (M), ethyl acetate (EA), methylene chloride (CH), and isopropyl alcohol (IA) treatments were applied. Finally, combined surface treatments were chosen and analyzed. Surface morphologies after treatments were observed by scanning electron microscopy and the flexural, shear, and impact strengths were tested. AB and chemical treatment with CH, M, and EA was used to improve all mechanical properties, and further improvement of the properties could be achieved by combining both types of treatments. Varied changes in surface morphologies were observed. Treatment with IA yielded less favorable results due to the low impact strength. The best results were achieved for the combination of AB and CH, but during the application of CH it was necessary to strictly control the exposure time.

Titanium-based materials are the most widely used materials in biomedical applications. However, according to literature findings, the degradation products of titanium have been associated with potential allergic reactions, inflammation, and bone resorption. The corrosion process of Ti-6Al-4V in the human body environment may be exacerbated by factors such as reduced pH levels and elevated concentrations of chloride compounds. Coatings made of biopolymers are gaining attention as they offer numerous advantages for enhancing implant functionality, including improved biocompatibility, bioactivity, wettability, drug release, and antibacterial activity. This study analyzes the physicochemical and electrochemical behavior of the Ti-6Al-4V ELI alloy subjected to PCL and PCL/TiO 2 deposition by the electrospinning method. To characterize the polymer-based layer, tests of chemical and phase composition, as well as surface morphology investigations, were performed. Wetting angle tests were conducted as part of assessing the physicochemical properties. The samples were subjected to corrosion behavior analysis, which included open circuit potential measurements, potentiodynamic tests, and the electrochemical impedance spectroscopy method. Additionally, the quantification of released ions post the potentiodynamic test was carried out using the inductively coupled plasma atomic emission spectrometry (ICP-AES) method. Cytotoxicity tests were also performed. It was found that surface modification by depositing a polymer-based layer on the titanium substrate material using the electrospinning method provides improved corrosion behavior, and the samples exhibit non-toxic properties.

Colonization of temporary denture soft linings and underlying tissues by yeast-like fungi is an important clinical problem due to the negative influence on the process of prosthetic treatment. Typical hygienic procedures are often insufficient to prevent fungal infections, so in this study, an antimicrobial filler (silver sodium hydrogen zirconium phosphate) was introduced into acrylic soft liner at concentrations of 1, 2, 4, 6, 8 and 10% ( w / w ). The effect of this modification on antifungal properties against Candida albicans , cytotoxicity, Shore A hardness, tensile strength and tensile bond strength, sorption and solubility was investigated, considering the recommended 30-day period of temporary soft lining use. The most favorable compilation of properties was obtained at a 1 to 6% filler content, for which nearly a total reduction in Candida albicans was registered even after 30 days of sample storing. The tensile and bond strength of these composites was at the desired and stable level and did not differ from the results for the control material. Hardness increased with the increasing concentration in filler but were within the range typical for soft lining materials and their changes during the experiment were similar to the control material. The materials were not cytotoxic and sorption and solubility levels were stable.

While functioning in the oral cavity, denture soft linings (SL) are exposed to contact with the microbiota. Dentures can offer perfect conditions for the multiplication of pathogenic yeast-like fungi, resulting in rapid colonisation of the surface of the materials used. In vitro experiments have also shown that yeast may penetrate SL. This may lead to changes in their initially beneficial functional properties. The aim of this work was to investigate the effect of three months of exposure to a Candida albicans suspension on the mechanical properties of SL material and its bond strength to the denture base polymer, and to additionally verify previous reports of penetration using a different methodology. Specimens of the SL material used were incubated for 30, 60 and 90 days in a suspension of Candida albicans strain (ATCC 10231). Their shore A hardness, tensile strength, and bond strength to acrylic resin were tested. The colonization of the surface and penetration on fractured specimens were analysed with scanning electron and inverted fluorescence microscopes. Exposure to yeast did not affect the mechanical properties. The surfaces of the samples were colonised, especially in crystallized structures of the medium; however, the penetration of hyphae and blastospores into the material was not observed.

In this study, two novel quaternary ammonium urethane-dimethacrylates (QAUDMAs) were designed for potential use as comonomers in antibacterial dental composite restorative materials. QAUDMAs were synthesized via the reaction of 1,3-bis(1-isocyanato-1-methylethyl)benzene with 2-(methacryloyloxy)ethyl-2-decylhydroxyethylmethylammonium bromide (QA10+TMXDI) and 2-(methacryloyloxy)ethyl-2-dodecylhydroxyethylmethylammonium bromide (QA12+TMXDI). Their compositions with common dental dimethacrylates comprising QAUDMA 20 wt.%, urethane-dimethacrylate monomer (UDMA) 20 wt.%, bisphenol A glycerolate dimethacrylate (Bis-GMA) 40 wt.%, and triethylene glycol dimethacrylate (TEGDMA) 20 wt.%, were photocured. The achieved copolymers were characterized for their physicochemical and mechanical properties, including their degree of conversion ( DC ), glass transition temperature ( T g ), polymerization shrinkage ( S ), water contact angle ( WCA ), flexural modulus ( E ), flexural strength ( FS ), hardness ( HB ), water sorption ( WS ), and water leachability ( WL ). The antibacterial activity of the copolymers was characterized by the minimum bactericidal concentration ( MBC ) and minimum inhibitory concentration ( MIC ) against Staphylococcus aureus and Escherichia coli . The achieved results were compared to the properties of a typical dental copolymer comprising UDMA 40 wt.%, Bis-GMA 40 wt.%, and TEGDMA 20 wt.%. The introduction of QAUDMAs did not deteriorate physicochemical and mechanical properties. The WS and WL increased; however, they were still satisfactory. The copolymer comprising QA10+TMXDI showed a higher antibacterial effect than that comprising QA12+TMXDI and that of the reference copolymer.

A significant problem related to the functioning of resin-based composites for dental fillings is secondary or recurrent caries, which is the reason for the need for repeated treatment. The cross-linked quaternary ammonium polyethylenimine nanoparticles (QA-PEI-NPs) have been shown to be a promising antibacterial agent against different bacteria, including cariogenic ones. However, little is known about the properties of dental dimethacrylate polymer-based composites enriched with QA-PEI-NPs. This research was carried out on experimental composites based on bis-GMA/UDMA/TEGDMA matrix enriched with 0.5, 1, 1.5, 2 and 3 (wt%) QA-PEI-NPs and reinforced with two glass fillers. The cured composites were tested for their adherence of Streptococcus Mutans bacteria, cell viability (MTT assay) with 48 h and 10-days extracts , degree of conversion (DC), water sorption (WSO), and solubility (WSL), water contact angle (CA), flexural modulus (E), flexural strength (FS), compressive strength (CS), and Vickers microhardness (HV). The investigated materials have shown a complete reduction in bacteria adherence and satisfactory biocompatibility. The QA-PEI-NPs additive has no effect on the DC, VH, and E values. QA-PEI-NPs increased the CA (a favorable change), the WSO and WSL (unfavorable changes) and decreased flexural strength, and compressive strength (unfavorable changes). The changes mentioned were insignificant and acceptable for most composites, excluding the highest antibacterial filler content. Probably the reason for the deterioration of some properties was low compatibility between filler particles and the matrix; therefore, it is worth extending the research by surface modification of QA-PEI-NPs to achieve the optimum performance characteristics., (© 2023. Springer Nature Limited.)

Objectives: This study assumed that the quaternary ammonium urethane-dimethacrylate derivative (QAUDMA-m, where m was 8, 10, 12, 14, 16, 18, and corresponded to the number of carbon atoms in the N-alkyl substituent) can be used to achieve copolymers with high mechanical performance and antibacterial activity., Methods: Photocured copolymers of bisphenol A glycerolate dimethacrylate (Bis-GMA) 40 wt%, QAUDMA-m 40 wt%, and triethylene glycol dimethacrylate (TEGDMA) 20 wt% (BG:QAm:TEG) were characterized by the degree of conversion (DC), flexural strength (FS), flexural modulus (E), hardness (HB), and antibacterial properties (the number of bacteria colonies adhered to copolymer surfaces and inhibition zone diameter (IZD)) against Staphylococcus aureus and Escherichia coli. Reference copolymers of Bis-GMA, urethane-dimethacrylate monomer (UDMA), and TEGDMA (BG:TEG and BG:UD:TEG) were also characterized., Results: The DC of BG:QAm:TEGs ranged from 0.59 to 0.68, HB from 83.84 to 153.91 MPa, FS from 50.81 to 74.47 MPa, and E from 1986.74 to 3716.68 MPa. The number of S. aureus and E. coli bacteria adhered to BG:QAm:TEG surfaces was from 0 (no bacteria observed) to 6.47 and 4.99 log(CFU/mL), respectively. IZD was from 10 and 5 mm (no inhibition zone) to 23 and 21 mm, respectively. Three copolymers: BG:QA8:TEG, BG:QA10:TEG, and BG:QA12:TEG had similar or better mechanical properties than the reference copolymers, but unlike them, they showed high antibacterial activity against both bacteria strains., Significance: The obtained copolymers can offer a good, mechanically efficient, bioactive alternative to BG:TEG and BG:UD:TEG copolymers. The use of such materials can help to make progress in dental health care., (Copyright © 2023 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

This study aimed to elucidate the physicochemical properties of copolymers comprising 40 wt.% bisphenol A glycerolate dimethacrylate (Bis-GMA), 40 wt.% quaternary ammonium urethane-dimethacrylate analogues (QAUDMA-m, where m corresponds to the number of carbon atoms in the N -alkyl substituent), and 20 wt.% triethylene glycol dimethacrylate (TEGDMA) copolymers (BG:QAm:TEGs). The BG:QAm:TEG liquid monomer compositions and reference compositions (40 wt.% Bis-GMA, 40 wt.% urethane-dimethacrylate (UDMA), 20 wt.% TEGDMA (BG:UD:TEG) and 60 wt.% Bis-GMA, 40 wt.% TEGDMA (BG:TEG)) were characterized in terms of their refractive index ( RI ) and monomer glass transition temperature ( Tg m ) and then photocured. The resulting copolymers were characterized in terms of the polymer glass transition temperature ( Tg p ), experimental polymerization shrinkage ( S e ), water contact angle ( WCA ), water sorption ( WS ), and water solubility ( SL ). The prepared BG:QAm:TEG liquid monomer compositions had RI in the range 1.4997-1.5129, and Tg m in the range -52.22 to -42.12 °C. The BG:QAm:TEG copolymers had Tg p ranging from 42.21 to 50.81 °C, S e ranging from 5.08 to 6.40%, WCA ranging from 81.41 to 99.53°, WS ranging from 25.94 to 68.27 µg/mm 3 , and SL ranging from 5.15 to 5.58 µg/mm 3 . Almost all of the developed BG:QAm:TEGs fulfilled the requirements for dental materials (except BG:QA8:TEG and BG:QA10:TEG, whose WS values exceeded the 40 µg/mm 3 limit).

The use of dental composites based on dimethacrylates that have quaternary ammonium groups is a promising solution in the field of antibacterial restorative materials. This study aimed to investigate the mechanical properties and behaviors in aqueous environments of a series of six copolymers (QA:TEG) comprising 60 wt.% quaternary ammonium urethane-dimethacrylate (QAUDMA) and 40 wt.% triethylene glycol dimethacrylate (TEGDMA); these copolymers are analogous to a common dental copolymer (BG:TEG), which comprises 60 wt.% bisphenol A glycerolate dimethacrylate (Bis-GMA) and 40 wt.% TEGDMA. Hardness ( HB ), flexural strength ( FS ), flexural modulus ( E ), water sorption ( WS ), and water solubility ( SL ) were assessed for this purpose. The pilot study of these copolymers showed that they have high antibacterial activity and good physicochemical properties. This paper revealed that QA:TEGs cannot replace BG:TEG due to their insufficient mechanical properties and poor behavior in water. However, the results can help to explain how QAUDMA-based materials work, and how their composition should be manipulated to produce the best performance. It was found that the longer the N -alkyl chain, the lower the HB , WS , and SL . The FS and E increased with the lengthening of the N- alkyl chain from eight to ten carbon atoms. Its further extension, to eighteen carbon atoms, caused a decrease in those parameters.

Yeast-like fungi such as Candida albicans ( C. albicans ) are the primary pathogenic microorganism in the oral cavity of denture wearers. The research available so far, conducted according to a protocol based on the exposure of specimens to a C. albicans suspension and their cutting with water cooling, shows that hard polymethyl methacrylate (PMMA) prosthetic materials are not only surface colonized, but also penetrated by microorganisms in a short time. This justifies the hypothesis that exposure to a suspension of the C. albicans strain causes the changes in mechanical properties due to surface colonization and/or penetration of the samples. In the current study, the chosen mechanical properties (flexural strength, flexural modulus, tensile strength, impact strength, ball indentation hardness, and surface Vickers hardness at 300 g load) of the PMMA denture base material Vertex RS (Vertex-Dental, The Netherlands) exposed for 30, 60, and 90 days to a suspension of C. albicans were investigated. The potential penetration of yeast was examined on the fractured surfaces (interior of specimens) to eliminate the risk of the contamination of samples during cutting. There was no influence on the flexural strength, flexural modulus, tensile strength, impact strength, or ball indentation hardness, but a significant decrease in surface hardness was registered. Microscopic observations did not confirm the penetration of C. albicans . On the surface, blastospores and pseudohyphae were observed in crystallized structures and in traces after grinding, which indicates that in clinical conditions, it is not penetration but the deterioration of surface quality, which may lead to the formation of microareas that are difficult to disinfect, causing rapid recolonization.

Abrasions and pressure ulcers on the oral mucosa are most often caused by excessive pressure or incorrect fitting of the denture. The use of soft relining materials can eliminate pain sensations and improve patient comfort. The main functional feature of soft elastomeric materials is the ability to discharge loads from the tissues of the mucosa. (1) Background: The aim of the work was a comparative laboratory study of ten materials used for the soft lining of acrylic dentures. (2) Methods: There were materials based on acrylates (Vertex Soft, Villacryl Soft, Flexacryl Soft) and silicones (Sofreliner Tough Medium, Sofreliner Tough Medium, Ufi Gel SC, GC Reline Soft, Elite Soft Relining, Molloplast). Laboratory tests include the analysis of the tensile bond strength between the relining material and the acrylic plate of the prosthesis. The tests were conducted taking into account 90-day term aging in the distilled water environment based on the methodology presented in the European Standard ISO 10139-2. (3) Results: After three months of observation, the highest strength of the joint was characterized by Flexacryl Soft acrylic, for which the average value was 2.5 MPa. The lowest average value of 0.89 MPa was recorded for the GC Reline Soft silicone material. Over time, an increase in the value of the strength of the combination of acrylic materials and a decrease in these values in the case of silicone materials was observed. (4) Conclusion: Each of the tested silicone materials showed all three types of damage, from adhesive to mixed to cohesive. All acrylic-based materials showed an adhesive type of failure. Time did not affect the type of destruction.