Search

Single-walled carbon nanotubes (SWCNTs) hold vast potential for future electronic devices due to their outstanding properties, however covalent functionalization often destroys the intrinsic properties of SWCNTs, thus limiting their full potential. Here, we demonstrate the fabrication of a functionalized graphene/semiconducting SWCNT (T@fG) heterostructured thin film transistor as a chemical sensor. In this structural configuration, graphene acts as an atom-thick, impermeable layer that can be covalently functionalized via facile diazonium chemistry to afford a high density of surface functional groups while protecting the underlying SWCNT network from chemical modification, even during a covalent chemical reaction. As a result, the highly functionalized carbon-based hybrid structure exhibits excellent transistor properties with a carrier mobility and ON/OFF ratio as high as 64 cm2/Vs and 5400, respectively. To demonstrate its use in potential applications, T@fG thin films were fabricated as aqueous ammonium sensors exhibiting a detection limit of 0.25 μM in a millimolar ionic strength solution, which is comparable with state-of-the-art aqueous ammonium nanosensors.

A critical challenge to translating field effect transistors into biochemical sensor platforms is the requirement of a gate electrode, which imposes restrictions on sensor device architectures and results in added expense, poorer scalability, and electrical noise. Here we show that it is possible to eliminate the need of the physical gate electrode and dielectrics altogether using a synthetic tube-in-a-tube (Tube∧2) semiconductor. Composed of a semiconducting single-walled carbon nanotube nested in a charged, impermeable covalent functional shell, Tube∧2 allows the semiconducting conduction pathway to be modulated solely by surface functional groups in a chemically gated-all-around configuration. The removal of physical gates significantly simplifies the device architecture and enables photolithography-free, highly scalable fabrication of transistor sensors in nonconventional configurations that are otherwise impossible. We show that concomitant FET sensitivity and single-mismatch selectivity can be achieved with Tube∧2 even in a two-terminal, thin film transistor device configuration that is as simple as a chemiresistor. Miniaturized two-terminal field effect point sensors can also be fabricated, using a straightforward dice-and-dip procedure, for the detection of tuberculosis biomarkers.

There is an urgent need for the development of technologies that allow the monitoring of protein expression and processing in tumor tissues resulting from development, physiology and disease state. To address the issue of cell heterogeneity in the tissue section, several microdissection techniques have been developed to provide a rapid and straightforward method for isolating selected subpopulations of cells for downstream molecular analysis. Development and demonstration of an effective discovery-based proteome platform, Gemini, are particularly highlighted for its capabilities of achieving ultrasensitive and comprehensive analysis of minute proteins extracted from targeted cells in tissue specimens. The greatest expectations for targeted proteomics research using enriched nonmalignant and malignant cells from high-quality fresh-frozen, formalin-fixed and paraffin-embedded specimens reside in the identification of diagnostic, prognostic and predictive biological markers in the clinical setting, as well as the discovery and validation of new protein targets in the biopharmaceutical industry.

Covalently functionalized, semiconducting double-walled carbon nanotubes exhibit remarkable properties and can outperform their single-walled carbon nanotube counterparts. In order to harness their potential for electronic applications, metallic double-walled carbon nanotubes must be separated from the semiconductors. However, the inner wall is inaccessible to current separation techniques which rely on the surface properties. Here, the first approach to address this challenge through electrical breakdown of metallic double-walled carbon nanotubes, both inner and outer walls, within networks of mixed electronic types is described. The intact semiconductors demonstrate a ∼62% retention of the ON-state conductance in thin film transistors in response to covalent functionalization. The selective elimination of the metallic pathways improves the ON/OFF ratio, by more than 360 times, to as high as 40 700, while simultaneously retaining high ON-state conductance.

A hybrid microchip/capillary electrophoresis (CE) system was developed to allow unbiased and lossless sample loading and high-throughput repeated injections. This new hybrid CE system consists of a poly(dimethylsiloxane) (PDMS) microchip sample injector featuring a pneumatic microvalve that separates a sample introduction channel from a short sample loading channel, and a fused-silica capillary separation column that connects seamlessly to the sample loading channel. The sample introduction channel is pressurized such that when the pneumatic microvalve opens briefly, a variable-volume sample plug is introduced into the loading channel. A high voltage for CE separation is continuously applied across the loading channel and the fused-silica capillary separation column. Analytes are rapidly separated in the fused-silica capillary, and following separation, high-sensitivity MS detection is accomplished via a sheathless CE/ESI-MS interface. The performance evaluation of the complete CE/ESI-MS platform demonstrated that reproducible sample injection with well controlled sample plug volumes could be achieved by using the PDMS microchip injector. The absence of band broadening from microchip to capillary indicated a minimum dead volume at the junction. The capabilities of the new CE/ESI-MS platform in performing high-throughput and quantitative sample analyses were demonstrated by the repeated sample injection without interrupting an ongoing separation and a linear dependence of the total analyte ion abundance on the sample plug volume using a mixture of peptide standards. The separation efficiency of the new platform was also evaluated systematically at different sample injection times, flow rates, and CE separation voltages.

Atom-thick materials such as single-walled carbon nanotubes (SWCNTs) and graphene exhibit ultrahigh sensitivity to chemical perturbation partly because all of the constituent atoms are surface atoms. However, low selectivity due to nonspecific binding on the graphitic surface is a challenging issue to many applications including chemical sensing. Here, we demonstrated simultaneous attainment of high sensitivity and selectivity in thin-film field effect transistors (TFTs) based on outer-wall selectively functionalized double-walled carbon nanotubes (DWCNTs). With carboxylic acid functionalized DWCNT TFTs, we obtained excellent gate modulation (on/off ratio as high as 4000) with relatively high ON currents at a CNT areal density as low as 35 ng/cm(2). The devices displayed an NH(3) sensitivity of 60 nM (or ~1 ppb), which is comparable to small molecule aqueous solution detection using state-of-the-art SWCNT TFT sensors while concomitantly achieving 6000 times higher chemical selectivity toward a variety of amine-containing analyte molecules over that of other small molecules. These results highlight the potential of using covalently functionalized double-walled carbon nanotubes for simultaneous ultrahigh selective and sensitive detection of chemicals and illustrate some of the structural advantages of this double-wall materials strategy to nanoelectronics.

Object Tumor-initiating cells are uniquely resilient to current treatment modalities and play an important role in tumor resistance and recurrence. The lack of specific tumor-initiating cell markers to identify and target these cells presents a major obstacle to effective directed therapy. Methods To identify tumor-initiating cell markers in primary brain tumors, the authors compared the proteomes of glioma tumor-initiating cells to their differentiated progeny using a novel, nongel/shotgun-based, multidimensional liquid-chromatography protein separation technique. An in vivo xenograft model was used to demonstrate the tumorigenic and stem cell properties of these cells. Western blot and immunofluorescence analyses were used to confirm findings of upregulated ciliary neurotrophic factor receptor subunit–α (CNTFRα) in undifferentiated tumor-initiating cells and gliomas of increasing tumor grade. Sequencing of the CNTFRα coding regions was performed for mutation analysis. Finally, antibody-dependent cell-mediated cytotoxicity was used to establish the role of CNTFRα as a potential immunotherapeutic target. Results Ciliary neurotrophic factor receptor subunit–α expression was increased in tumor-initiating cells and was decreased in the cells' differentiated progeny, and expression levels increased with glioma grade. Mutations of CNTFRα are not common in gliomas. Functional studies using CNTF treatment in glioma tumor-initiating cells showed induction of differentiation through the CNTFRα pathway. Treatment with anti-CNTFRα antibody resulted in increased antibody-dependent cell-mediated cytotoxicity in CNTFRα expressing DAOY cells but not in cell lines that lack CNTFRα. Conclusions These data indicate that CNTFRα plays a role in the formation or maintenance of tumor-initiating cells in gliomas, is a marker that correlates with histological grade, may underlie treatment resistance in some cases, and is a potential therapeutic target.

Cellular senescence acts as a potent barrier to tumorigenesis and contributes to the anti-tumor activity of certain chemotherapeutic agents. Senescent cells undergo a stable cell cycle arrest controlled by RB and p53 and, in addition, display a senescence-associated secretory phenotype (SASP) involving the production of factors that reinforce the senescence arrest, alter the microenvironment, and trigger immune surveillance of the senescent cells. Through a proteomics analysis of senescent chromatin, we identified the nuclear factor-κB (NF-κB) subunit p65 as a major transcription factor that accumulates on chromatin of senescent cells. We found that NF-κB acts as a master regulator of the SASP, influencing the expression of more genes than RB and p53 combined. In cultured fibroblasts, NF-κB suppression causes escape from immune recognition by natural killer (NK) cells and cooperates with p53 inactivation to bypass senescence. In a mouse lymphoma model, NF-κB inhibition bypasses treatment-induced senescence, producing drug resistance, early relapse, and reduced survival. Our results demonstrate that NF-κB controls both cell-autonomous and non-cell-autonomous aspects of the senescence program and identify a tumor-suppressive function of NF-κB that contributes to the outcome of cancer therapy.

Atom-thick materials such as single-wall carbon nanotubes (SWNTs) and graphene are prone to chemical attacks because all constituent atoms are exposed. Here we report the retention of optical and electrical properties of inner tubes in heavily functionalized double-wall carbon nanotubes (DWNTs). Correlated optical absorption spectroscopy, Raman scattering, and thin film electrical conductivity all suggest that an inner tube behaves strikingly similar to a pristine SWNT; however, because of the protection of the outer wall, the inner tube can survive aggressive chemical attacks (e.g., by diazonium chemistry) without compromising physical properties. At the saturation limit of the diazonium functionalization, an SWNT network becomes electrically insulating; in stark contrast, the double-walled structure retains ∼50% of the initial conductivity, owing to the intact inner tube pathway. These results suggest the possibility of high-performance DWNT electronic devices with important capabilities for tailored su...

A compelling need exists for the development of technologies that facilitate and accelerate the discovery of novel protein biomarkers with therapeutic and diagnostic potential. The inherent disadvantage of biomarker dilution in complex biological fluids such as serum/plasma, urine, and saliva necessitates highly sensitive analytical approaches, often exceeding the dynamic range of currently available proteomic platforms. Thus, investigative studies directed at tissues obtained from the primary site of pathology probably afford the best opportunity for the discovery of disease biomarkers. This review therefore focuses on the most recent advances in capillary electrophoresis-based single and multidimensional separations coupled with ESI-MS for performing comprehensive and comparative analysis of protein expression profiles within clinical specimens. Advanced sample preparation techniques, including tissue microdissection, detergent-based membrane protein extraction, and heat-induced protein retrieval, further enable targeted protein profiling of both fresh-frozen, formalin-fixed, and paraffin-embedded tissues. Comparative proteomics involving measurements in changes of biological pathways or functional processes are expected to provide relevant disease-associated markers and networks, molecular relationships among different stages of disease, and molecular mechanisms that drive the progression of disease. From a practical perspective, the evaluation of comparative proteomic dataset within a biological context is essential for high-throughput data validation, prioritization of follow-on biomarker selection, and validation experiments.

There is increasing acceptance of the critical importance of correlating the morphologic features of tissue with the data obtained from various molecular analytic techniques. Access to archived formalin-fixed and paraffin-embedded (FFPE) tissue specimens via shotgun-based proteomic analyses may, therefore, open new avenues for both prospective and retrospective translational research. However, one of the remaining issues in performing comparative proteomic measurements among FFPE tissues relates to potential variability in protein composition and retrieval based on length of storage periods. Optimized protein extraction and digestion procedures for handling FFPE tissues are coupled with the capillary isotachophoresis-based proteome technology to evaluate the effects of length of storage period on archival tissue proteome analysis across 10 archived uterine mesenchymal tumor tissue blocks, including 9 uterine leiomyomas dating from 1990 to 2002 and a single case of alveolar soft part sarcoma (ASPS) from 1980. Several statistical measures, including the Pearson correlation coefficient, coefficient of variance, k-means clustering, and ANOVA, are employed to evaluate the possibility of an archival effect on individual proteins or groups of proteins within nine leiomyomas. Low abundance proteins may be more susceptible to the long-term storage as these proteins are more difficult to be retrieved and extracted as the tissue block ages in paraffin. Despite using tissue blocks stored for as many as 28 years, high confidence and comparative proteome analysis between the leiomyomas and the sarcoma is achieved. Though sharing over 1800 common proteins in a core set, a total of 80 proteins unique to the sarcoma are identified distinguishing the ASPS from the leiomyomas. Vacuolar proton translocating ATPase 116 kDa subunit isoform a3, one of the unique proteins expressed in the ASPS, is further validated by immunohistochemistry (IHC). Although IHC is highly sensitive and provides the subcellular resolution, mass spectrometry-based proteome profiling enables global identification and quantification of thousands of proteins without a priori knowledge of individual proteins being analyzed or the need of validated antibodies.

The proteome of human salivary fluid has the potential to open new doors for disease biomarker discovery. A recent study to comprehensively identify and catalog the human ductal salivary proteome led to the compilation of 1166 proteins. The protein complexity of both saliva and plasma is large, suggesting that a comparison of these two proteomes will provide valuable insight into their physiological significance and an understanding of the unique and overlapping disease diagnostic potential that each fluid provides. To create a more comprehensive catalog of human salivary proteins, we have first compiled an extensive list of proteins from whole saliva (WS) identified through MS experiments. The WS list is thereafter combined with the proteins identified from the ductal parotid, and submandibular and sublingual (parotid/SMSL) salivas. In parallel, a core dataset of the human plasma proteome with 3020 protein identifications was recently released. A total of 1939 nonredundant salivary proteins were compiled from a total of 19 474 unique peptide sequences identified from whole and ductal salivas; 740 out of the total 1939 salivary proteins were identified in both whole and ductal saliva. A total of 597 of the salivary proteins have been observed in plasma. Gene ontology (GO) analysis showed similarities in the distributions of the saliva and plasma proteomes with regard to cellular localization, biological processes, and molecular function, but revealed differences which may be related to the different physiological functions of saliva and plasma. The comprehensive catalog of the salivary proteome and its comparison to the plasma proteome provides insights useful for future study, such as exploration of potential biomarkers for disease diagnostics.

Multidimensional separations of the peptides resulting from enzymatic digestions of complex protein mixtures prior to MS/MS, namely shotgun proteomics, is increasingly utilized for large-scale identification and quantitation of proteins. Inherent to the performance of proteomic measurements is the resolving power of each of the separations both separately and in combination. By simply raising the number of CIEF fractions, the resulting enhancement in the overall peak capacity of combined CIEF/nano-RPLC separations greatly reduces the complexity of eluted peptides prior to MS detection and sequencing and increases the proteome coverage. The capabilities of the CIEF-based proteome platform coupled with the spectral counting approach to confidently and reproducibly quantify proteins and changes in protein expression levels among samples are evaluated. Analytical reproducibility of relative protein abundance is determined to exhibit a Pearson R(2) value greater than 0.99 and a CV of 14.1%. The platform is demonstrated to be capable of measuring changes in protein expression as low as 1.5-fold, with confidence following multiple testing adjustment.

In situ photopolymerized polyacrylamide (PAAm) gel plugs are used as hydrodynamic flow control elements in a multidimensional microfluidic system combining IEF and parallel SDS gel electrophoresis for protein separations. The PAAm gel plugs offer a simple method to reduce undesirable bulk flow and limit reagent/sample crosstalk without placing unwanted constraints on the selection of separation media, and without hindering electrokinetic ion migration in the complex microchannel network. In addition to improving separation reproducibility, the discrete gel plugs integrated into critical regions of the chip enable the use of a simple pressure-driven sample injection method which avoids electrokinetic injection bias. The gel plugs also serve to greatly simplify operation of the spatially multiplexed system by eliminating the need for complex external fluidic interfaces. Using an FITC-labeled Escherichia coli cell lysate as a model system, the use of gel plugs is shown to significantly enhance separation reproducibility in a chip containing five parallel CGE channels, with an average variance in peak elution time of only 4.1%.

The foundation for saliva-based diagnostics is the development of a complete catalog of secreted proteins detectable in saliva. Besides protein complexity, the greatest bioanalytical challenge facing comprehensive analysis of saliva samples is related to the large variation of protein relative abundances including the presence of high-abundance proteins such as amylases, mucins, proline-rich proteins (PRPs), and secretory IgA complex. Among a number of electrokinetic separation techniques, transient capillary isotachophoresis/capillary zone electrophoresis (CITP/CZE) specifically targets trace amounts of proteins and thus reduces the range of relative protein abundances for providing unparallel advantages toward the identification of low-abundance proteins. By employing a CITP/CZE-based multidimensional separation platform coupled with electrospray ionization-tandem mass spectrometry (ESI-tandem MS), a total of 6112 fully tryptic peptides are sequenced at a 1% false discovery rate (FDR), leading to the identification of 1479 distinct human SwissProt protein entries. By comparing with capillary isoelectric focusing (CIEF) as another electrokinetics-based stacking approach, CITP/CZE not only offers a broad field of application but also is less prone to protein/peptide precipitation during the analysis. The ultrahigh resolving power of CITP/CZE is evidenced by the large number of distinct peptide identifications measured from each CITP fraction together with the low peptide fraction overlapping among identified peptides. Furthermore, when evaluating the protein sequence coverage by the number of distinct peptides mapping to each protein identification, the CITP-based proteome technology similarly achieves the superior performance with 674 proteins (46%) having three or more distinct peptides, 288 (19%) having two distinct peptides, and 517 (35%) having a single distinct peptide.

As demonstrated in this study, a CIEF-based multidimensional separation platform not only is compatible with the detergent-based membrane protein preparation protocol, but also achieves both the largest yeast membrane proteome coverage and the most comprehensive analysis of the yeast proteome to date. By using a 1% false discovery rate for total peptide identifications, a total of 2513 distinct yeast proteins are identified from the SDS-solubilized fraction with an average of 5.4 peptides leading to each protein identification. Among proteins identified from the SDS-solubilized fraction, 407 proteins are predicted to contain at least two or more transmembrane domains using TMHMM (www.cbs.dtu.dk/services/TMHMM-2.0/), corresponding to 46% yeast membrane proteome coverage. Only four additional membrane proteins are identified in the soluble and urea-solubilized fractions, affirming the utility of SDS extraction for enriching the membrane proteome. By combining proteome results obtained from the soluble, urea-solubilized, and SDS-solubilized fractions, a single yeast proteome analysis yields the identification of 3632 distinct yeast proteins, corresponding to 55% theoretical yeast proteome coverage or 70% of proteins predicted to be expressed during log-phase growth in rich media.

Two morphological forms of programmed cell death, apoptosis and autophagic cell death, remove unneeded or damaged cells during animal development. Although the mechanisms that regulate apoptosis are well studied, little is known about autophagic cell death. A shotgun proteome analysis of purified dying larval salivary glands in Drosophila was used to identify proteins that are expressed during autophagic programmed cell death. A total of 5661 proteins were identified from stages before and after the onset of cell death. Analyses of these data enabled us to identify proteins from a number of interesting categories including regulators of transcription, the apoptosis, autophagy, lysosomal, and ubiquitin proteasome degradation pathways, and proteins involved in growth control. Several of the identified proteins, including the serine/threonine kinase warts (Wts), were not detected using whole-genome DNA microarrays, providing support for the importance of such high-throughput proteomic technology. Wts regulates cell-cycle arrest and apoptosis, and significantly, mutations in wts prevent destruction of salivary glands.

This work expands our tissue proteome capabilities from the analysis of soluble proteins in previous studies to the examination of membrane proteins within the pellets of enriched and selectively isolated tumor cells procured from microdissected tissue specimens. The pellets of targeted ovarian tumor cells are treated by two different membrane protein extraction methods, including the use of detergent and organic solvent. The detergent-based membrane protein preparation protocol not only extracts proteins effectively from cell pellets but also is compatible with subsequent proteome analysis using combined capillary isoelctric focusing/nano reversed-phase liquid chromatography separations coupled with nano electrospray ionization mass spectrometry. Among proteins identified from an amount of pellet equivalent to 20 000 cells, 773 proteins are predicted to contain one or more transmembrane domains, corresponding to 22% membrane proteome coverage within the SwissProt Human protein sequence entries.

The field of microfluidics continues to offer great promise as an enabling technology for advanced analytical tools. For biomolecular analysis, there is often a critical need to couple on-chip microfluidic sample manipulation with back-end MS. Though interfacing microfluidics to MS has been most often reported through the use of direct ESI-MS, there are compelling reasons for coupling microfluidics to MALDI-MS as an alternative to ESI-MS for both online and offline analysis. The intent of this review is to provide a summary of recent developments in the integration of microfluidic systems with MALDI-MS, with an emphasis on applications in proteomics. Key points are summarized, followed by a review of relevant technologies and a discussion of outlook for the field.

Development of the capability to enable large-scale proteome studies, analogous to comprehensive gene expression analysis, will clearly have far-reaching impacts on protein biomarker investigations of human diseases such as cancer through interrogation of the archived fresh frozen and formalin-fixed and paraffin-embedded tissue collections. This review therefore focuses on the most recent advances in microdissection techniques and proteome platforms for procuring homogeneous subpopulations of tumor cells or structures and performing comprehensive analysis of protein profiles within tissue specimens, respectively. Developments in capillary separations capable of providing extremely high resolving power and selective analyte enrichment are particularly highlighted for their roles within the broader context of a state-of-the-art integrated tissue proteome effort. The capabilities of CIEF-based multidimensional separations for performing proteome analysis from minute samples create new opportunities in the pursuit of biomarker discovery using enriched and selected cell populations procured from tissue specimens. These proteome technological advances combined with recently developed tissue microdissection techniques provide powerful tools for those seeking to gain a greater understanding at the global level of the cellular machinery associated with human diseases such as cancer.

Besides the complexity in protein samples of biological origin, probably the greatest challenge presently facing comprehensive proteome analysis is related to the large variation of protein relative abundances (>6 orders of magnitude), having potential biological significance in mammalian systems. As demonstrated in this work, transient capillary ITP/zone electrophoresis (CITP/CZE) provides selective analyte enrichment through electrokinetic stacking and extremely high resolving power toward protein and peptide mixtures. The result of the CITP process is that major components may be diluted, but trace compounds are concentrated. The on-column transition of CITP to CZE minimizes additional band broadening while providing superior analyte resolution. Online coupling of transient CITP/CZE with nano-ESI-MS allows ultrasensitive detection of trace peptides at levels of subnanomolar concentration or subfemtomole mass in complex peptide mixtures. More importantly, selective enrichment of trace peptides enables the identification and sequence analysis of low-abundance peptides co-migrated with highly abundant species at a concentration ratio of 1:500 000. The combined CITP/CZE-nano-ESI-MS system is demonstrated to be at least one to two orders of magnitude more sensitive than that attained in conventional electrophoretic and chromatographic-based proteome technologies over a wide dynamic concentration range, potentially allowing comprehensive analysis of protein profiles within a small cell population and limited tissue samples using conventional mass spectrometers. Furthermore, the speed of CITP/CZE separation and the lack of column equilibration in CITP/CZE not only improve the throughput of proteome analysis, but also facilitate its seamless integration with other separation technologies in a multidimensional protein identification platform.

An integrated UV absorbance detection system employing a novel silicon-in-plastic technology to seamlessly integrate bare UV photodiode chips into polymer microfluidic systems has been developed. Detection platforms fabricated using this approach exhibit exceptionally low concentration and mass detection limits down to 15 nM and 9.8 amol, respectively, for bovine serum albumin (BSA) as a model protein. In addition to providing high sensitivity, sub-nanoliter detection volumes are enabled by the use of direct photodiode integration. The fabrication methodology is detailed, and system performance metrics including detection limits, detection volume, dynamic range, and linearity are reported.

The off-line coupling of polymer microfluidics to MALDI-MS is presented using electrospray deposition. Using polycarbonate microfluidic chips with integrated hydrophobic membrane electrospray tips, peptides and proteins are deposited onto a stainless steel target followed by MALDI-MS analysis. Microchip electrospray deposition is found to yield excellent spatial control and homogeneity of deposited peptide spots, and significantly improved MALDI-MS spectral reproducibility compared to traditional target preparation methods. A detection limit of 3.5 fmol is demonstrated for angiotensin. Furthermore, multiple electrospray tips on a single chip provide the ability to simultaneously elute parallel sample streams onto a MALDI target for high-throughput multiplexed analysis. Using a three-element electrospray tip array with 150 microm spacing, the simultaneous deposition of bradykinin, fibrinopeptide, and angiotensin is achieved with no cross talk between deposited samples. In addition, in-line proteolytic digestion of intact proteins is successfully achieved during the electrospray process by binding trypsin within the electrospray membrane, eliminating the need for on-probe digestion prior to MALDI-MS. The technology offers promise for a range of microfluidic platforms designed for high-throughput multiplexed proteomic analyses in which simultaneous on-chip separations require an effective interface to MS.

This study demonstrates the ability to perform sensitive proteome analysis on the limited protein quantities available through tissue microdissection. Capillary isoelectric focusing combined with nano-reversed-phase liquid chromatography in an automated and integrated platform not only provides systematic resolution of complex peptide mixtures based on their differences in isoelectric point and hydrophobicity but also eliminates peptide loss and analyte dilution. In comparison with strong cation exchange chromatography, the significant advantages of electrokinetic focusing-based separations include high resolving power, high concentration and narrow analyte bands, and effective usage of electrospray ionization-tandem MS toward peptide identifications. Through the use of capillary isoelectric focusing-based multidimensional peptide separations, a total of 6866 fully tryptic peptides were detected, leading to the identification of 1820 distinct proteins. Each distinct protein was identified by at least one distinct peptide sequence. These high mass accuracy and high-confidence identifications were generated from three proteome runs of a single glioblastoma multiforme tissue sample, each run consuming only 10 microg of total protein, an amount corresponding to 20,000 selectively isolated cells. Instead of performing multiple runs of multidimensional separations, the overall peak capacity can be greatly enhanced for mining deeper into tissue proteomics by increasing the number of CIEF fractions without an accompanying increase in sample consumption.

For top-down proteomics, nano-reversed phase liquid chromatography (RPLC) plays a major role in both single and multidimensional protein separations in an effort to increase the overall peak capacity for the resolution of complex protein mixtures prior to mass spectrometry analysis. Effects of various chromatography conditions, including alkyl chain length in the stationary phase, capillary column temperature, and ion-pairing agent, on the resolution of intact proteins are studied using nano-RPLC-electrospray ionization-mass spectrometry. Optimal chromatography conditions include the use of C 18 column heated at 60 ° C and the addition of trifluoroacetic acid instead of heptafluorobutyric acid as the ion-paring agent in the mobile phase. Under optimized chromatography conditions, there are no significant differences in the separation performance of yeast cell lysates present in the native versus denatured states. Denatured yeast proteins resolved and eluted from nano-RPLC can be subjected to proteolytic digestion in an on- or off-line approach to provide improved protein sequence coverage toward protein identification in a combined top-down/bottom-up proteome platform.

A simple method for fabricating nanoscale channels based on thermomechanical deformation of rigid polymer substrates is demonstrated. Polycarbonate preforms containing microchannels with cross-sectional dimensions on the order of tens of micrometers are controllably deformed to produce submicrometer dimensions. The reduced channel dimensions are achieved by heating the preform while applying a uniaxial tensile force to reduce channel cross sections through the Poisson effect. Nanochannels with circular or elliptical cross sections are defined by varying the channel position and preform geometry prior to deformation. Arrays of parallel nanochannels with critical dimensions down to 400 nm are described. Using the fabrication method, a nanochannel network is fabricated for the detection of single protein molecules via confocal fluorescence microscopy. The chip includes a detection channel with cross-sectional dimensions approaching the confocal volume dimensions of the detection optics and a larger adjacent reference channel used to optimize focusing. Detection of fluorescently labeled bovine serum albumin at 15 and 150 nM concentrations is presented, demonstrating the ability to perform single-molecule fluorescence measurements in polycarbonate chips using visible wavelengths for excitation and detection.

An electronic protein transfer technique is described for achieving the rapid and efficient recovery of sodium dodecyl sulfate (SDS)-protein complexes from polyacrylamide gels. This process involves the use of small-dimension capillaries in physical contact with a resolved protein band within the polyacrylamide gel, providing a large potential drop and high electric field strength at the capillary/gel interface. Several factors controlling the electronic protein transfer, including the applied electric field strength, the electrophoresis buffer concentration, and the capillary dimension, are studied to further enhance the use of field-amplification for sample stacking of extracted SDS-protein complexes. As a result of sample stacking, the extracted proteins from a 50 ng gel loading are present in a narrow ( approximately 80 nL) and highly concentrated (0.46 mg/mL or 3.3 x 10(-5) M for cytochrome c) solution plug. Three model proteins with molecular mass ranging from 14 kDa (cytochrome c) to 116 kDa (beta-galactosidase) are stained by Coomassie blue and electrophoretically extracted from gels with protein loadings as low as 50 ng. The capillary format of the electronic protein transfer technique allows direct deposition of extracted proteins onto a matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) target. Various matrices and solvent compositions are evaluated for the analysis of extracted and concentrated SDS-protein complexes using MALDI-MS. The electronic protein transfer technique, when operated under optimized conditions, is demonstrated for the effective (70% recovery), speedy (less than 5 min), and sensitive MS identification of gel resolved proteins (as low as 50 ng).

Microfluidic field-effect flow control (FEFC) modifies the zeta potential of electroosmotic flow using a transverse electric field applied through the microchannel wall. Previously demonstrated in silicon-based and glass microsystems, FEFC is presented here as an elegant method for flow control in polymer-based microfluidics with a simple and low-cost fabrication process. In addition to direct FEFC flow modulation, independent transverse electric fields in connected microchannels are demonstrated to produce a differential pumping rate between the microchannels. The different electroosmotic pumping rates formed by local zeta potential control induce an internal pressure at the microchannel intersection, resulting in hydrodynamic pumping through an interconnecting field-free microchannel. Modulation of the voltages applied to the gate electrodes adjusts the magnitude and direction of the bidirectional pressure pumping, with fine resolution volume flow rates from -2 to 2 nL/min in the field-free microchannel demonstrated.

An integrated protein concentration/separation system, combining non-native isoelectric focusing (IEF) with sodium dodecyl sulfate (SDS) gel electrophoresis on a polymer microfluidic chip, is reported. The system provides significant analyte concentration and extremely high resolving power for separated protein mixtures. The ability to introduce and isolate multiple separation media in a plastic microfluidic network is one of two key requirements for achieving multidimensional protein separations. The second requirement lies in the quantitative transfer of focused proteins from the first to second separation dimensions without significant loss in the resolution acquired from the first dimension. Rather than sequentially sampling protein analytes eluted from IEF, focused proteins are electrokinetically transferred into an array of orthogonal microchannels and further resolved by SDS gel electrophoresis in a parallel and high-throughput format. Resolved protein analytes are monitored using noncovalent, envi...

This work focuses on the development of a multidimensional electrokinetic-based separation/concentration platform coupled with electrospray ionization-Fourier transform ion cyclotron resonance mass spectrometry (ESI-FTICR-MS) for achieving the high resolution and ultrasensitive analysis of complex protein/peptide mixtures. A microdialysis junction is employed as the interface for on-line combination of capillary isoelectric focusing (CIEF) with transient capillary isotachophoresis/zone electrophoresis (CITP/CZE) in an integrated platform. Besides the excellent resolving power afforded by both CIEF and CZE separations, the electrokinetic focusing/stacking effects of CIEF and CITP greatly enhance the dynamic range and detection sensitivity of MS for protein identification. The constructed multidimensional separation/concentration platform is demonstrated for the analysis of Shewanella oneidensis proteome, which has considerable implications toward the bioremediation of environmental pollutants. The electrokinetic-based platform offers the overall peak capacity comparable to those obtained using multidimensional chromatography systems, but with a much shorter run time and no need for column regeneration. Most importantly, a total of 1174 unique proteins, corresponding to 26.5% proteome coverage, are identified from the cytosolic fraction of S. oneidensis, while requiring500 ng of proteolytic digest loaded in the CIEF capillary. The ultrasensitive capabilities of electrokinetic-based proteome approach are attributed to the concentration effect in CIEF, the electrokinetic stacking of CITP, the nanoscale peak volume in CZE, the "accurate mass tag" strategy for protein/peptide identification, and the high-sensitivity, high-resolution, and high-mass measurement accuracy of FTICR-MS.

An integrated proteome concentration/separation approach involving on-line combination of capillary isoelectric focusing (CIEF) with capillary reversed-phase liquid chromatography (CRPLC) is developed for providing significant analyte concentration and extremely high resolving power toward protein and peptide mixtures. Upon completion of analyte focusing, the self-sharpening effect greatly restricts analyte diffusion and contributes to analyte stacking in narrowly focused bands with a concentration factor of ∼240. In addition to analyte focusing, CIEF as the first separation dimension resolves proteins/peptides on the basis of their differences in pI and offers greater resolving power than that achieved in strong cation exchange chromatography. The grouping of two highly resolving and completely orthogonal separation techniques of CIEF and CRPLC, together with analyte focusing and concentration, significantly enhances the dynamic range and sensitivity of conventional mass spectrometry toward the identific...

Isoelectric focusing (IEF) separations, in general, involve the use of the entire channel filled with a solution mixture containing protein/peptide analytes and carrier ampholytes for the creation of a pH gradient. Thus, the preparative capabilities of IEF are inherently greater than most microfluidics-based electrokinetic separation techniques. To further increase sample loading and therefore the concentrations of focused analytes, a dynamic approach, which is based on electrokinetic injection of proteins/peptides from solution reservoirs, is demonstrated in this study. The proteins/peptides continuously migrate into the plastic microchannel and encounter a pH gradient established by carrier ampholytes originally present in the channel for focusing and separation. Dynamic sample introduction and analyte focusing in plastic microfluidic devices can be directly controlled by various electrokinetic conditions, including the injection time and the applied electric field strength. Differences in the sample loading are contributed by electrokinetic injection bias and are affected by the individual analyte's electrophoretic mobility. Under the influence of 30 min electrokinetic injection at constant electric field strength of 500 V/cm, the sample loading is enhanced by approximately 10-100 fold in comparison with conventional IEF.

A commonly used capillary fitting is employed for housing miniaturized membrane chromatography for performing reversed-phase peptide separations. By placing a hydrophobic and porous polyvinylidene fluoride membrane around the end of a polymer sleeve, the assembly of capillary fitting not only provides the stationary phase, but also establishes the necessary flow paths using capillary connections. The miniaturized membrane chromatography system is coupled with a micro-enzyme reactor containing immobilized trypsins for performing rapid protein digestion, peptide separation, and protein identification using electrospray ionization mass spectrometry. Separation performance of cytochrome c digest in miniaturized membrane chromatography is compared with the results obtained from micro-LC and capillary LC. The efficacy and the potentials of miniaturized membrane chromatography in tryptic mapping are reported. The use of miniaturized membrane chromatography allows significant reduction in sample consumption together with enhanced detection sensitivity. By minimizing the void volume in miniaturized membrane chromatography, the elution times of cytochrome c peptides are significantly shortened in this study in comparison with our previous results, and are comparable with those in micro-LC and capillary LC using considerably higher mobile phase flow-rates.

On-line combination of capillary isoelectric focusing (CIEF) with capillary reversed-phase liquid chromatography (CRPLC) is developed using a microinjector as the interface for performing two-dimensional (2-D) protein/peptide separations of complex protein mixtures. The focusing effect of CIEF not only contributes to a high-resolution protein/peptide separation, but also may permit the analysis of low-abundance proteins with a typical concentration factor of 50-100 times. The preparative capabilities of CIEF are much larger than most of capillary-based electrokinetic separation techniques since the entire capillary is initially filled with a solution containing proteins/peptides and carrier ampholytes for the creation of a pH gradient inside the capillary. The focused peptides which have a similar pI are coinjected into the second separation dimension and further resolved by their differences in hydrophobicity. The resolving power of combined CIEF-CRPLC system is demonstrated using the soluble fraction of Drosophila salivary glands taken from a period beginning before steroid-triggered programmed cell death and extending to its completion. The separation mechanisms of CIEF and CRPLC are completely orthogonal and the overall peak capacity is estimated to be around approximately 1800 over a run time of less than 8 h. Significant enhancement in the separation peak capacity can be realized by further increasing the number of CIEF fractions and/or slowing the solvent gradient in CRPLC, however, at the expense of overall analysis time. The results of our preliminary studies display significant differences in the separation profiles of peptide samples obtained from salivary glands of animals staged at the 6 and 12 h following puparium formation.

A microdialysis junction is employed as the interface for on-line coupling of capillary isoelectric focusing with transient isotachophoresis-zone electrophoresis in a two-dimensional separation system. Capillary isoelectric focusing not only provides high-resolution separation of tryptic peptides based on their differences in isoelectric point, but also potentially allows the analysis of low-abundance proteins with a typical concentration factor of 50-100 times. Carrier ampholytes, employed for the creation of a pH gradient during focusing, are further utilized as the leading electrolyte in the second separation dimension, transient isotachophoresis-zone electrophoresis. Many peptides which have the same isoelectric point would most likely have different charge-to-mass ratios, and thus different electrophoretic mobilities in zone electrophoresis. Two-dimensional separation of proteolytic peptides is demonstrated using standard proteins, including cytochrome c, ribonuclease A, and carbonic anhydrase II. The maximum peak capacity is estimated to be around approximately 1600 and can be significantly increased by simply increasing the capillary column length and manipulating the range of pH gradient in isoelectric focusing. In addition to enhanced separation efficiency and resolution, this two-dimensional electrokinetic separation system permits sensitive and comprehensive analysis of peptide fragments, especially when integrated with electrospray ionization mass spectrometry for peptide/protein identification.

A gel protein capillary extraction apparatus is developed and demonstrated for its rapid and effective transfer of SDS-protein complexes from polyacrylamide gel to a fused-silica capillary. The small dimensions of capillary columns permit the application of high voltages for achieving rapid and effective transfer of gel proteins. Furthermore, the fused-silica capillaries are internally coated with polyacrylamide for the elimination of electroosmotic pumping and protein adsorption onto the capillary wall. The extracted proteins are present in a highly concentrated solution plug as the result of field amplification and sample stacking during the extraction process. Three model proteins, including cytochrome c (14 kDa), ovalbumin (45 kDa), and beta-galactosidase (116 kDa), are visualized using coomassie blue staining and electrophoretically extracted from the gels with protein loading as low as 50 ng. The SDS-cytochrome c complexes extracted from a 50-ng protein loading are concentrated in a 30-nL solution plug inside the capillary with an estimated concentration of 0. 1 mg/mL or 10(-5) M. The capillary format allows the straightforward integration of a miniaturized trypsin-membrane reactor for on-line proteolytic digestion and ESI-MS analysis for protein/peptide identification.

A plastic microfluidic system, containing porous poly(vinylidene fluoride) (PVDF) membranes adsorbed with bovine serum albumin (BSA), is demonstrated for high resolution chiral separation of racemic tryptophan and thiopental mixtures. Microfluidic networks on poly(dimethylsiloxane) (PDMS) substrates are fabricated by capillary molding technique. This miniaturized chiral separation system consists of two layers of PVDF membranes which are sandwiched between two PDMS slabs containing microchannels facing the membranes. On-line adsorption of BSA onto the membranes is employed for the preparation of chiral stationary phase and the evaluation of solution conditions in an effort to achieve maximum protein adsorption. Variations in the mobile phase conditions, including solution pH and ammonium sulfate concentration, are studied for their effects on chiral separation. Based on the large surface area to volume ratio of porous membrane media, adsorbed BSA onto the PVDF membranes enables high resolution separation of racemic mixtures with sample consumption of sub-nanogram or less in the integrated microfluidic networks. In addition, the membrane pore diameter in the submicron range eliminates the constraints of diffusional mass-transfer resistance during protein adsorption and chiral chromatographic processes.

The concept of microfluidics has significantly influenced the design and the implementation of modern bioanalytical systems due to the fact that these miniaturized devices can handle and manipulate samples in a much more efficient way than conventional instruments. In an analogy to the development of microelectronics, increasingly sophisticated devices with greater functionalities have become one of the major goals being pursued in the area of micrototal analysis systems. The incorporation of polymeric membranes into microfluidic networks has therefore been employed in an effort to enhance the functionalities of these microfabricated devices. These commercially available membranes are porous, flexible, mechanically robust and compatible with plastic microfluidic networks. The large surface area-to-volume ratio of porous membrane media is particularly important for achieving rapid buffer exchange during microdialysis and obtaining ultrahigh concentration of adsorbed enzymes for various biochemical reactions. Furthermore, the membrane pore diameter in the sub-microm range eliminates the constraints of diffusional mass-transfer resistance for performing chiral separation using adsorbed protein as the chiral stationary phase. A review on the recent advancement in the integration of polymeric membranes with microfluidic networks is presented for their widespread applications in bioanalytical chemistry.

The application of the field-effect for direct control of electroosmosis in a polydimethylsiloxane (PDMS)-based microfluidic system, constructed on a silicon wafer with a 2.0 microm electrically insulating layer of silicon dioxide, is demonstrated. This microfluidic system consists of a 2.0 cm open microchannel fabricated on a PDMS slab, which can reversibly adhere to the silicon wafer to form a hybrid microfluidic device. Aside from mechanically serving as a robust bottom substrate to seal the channel and support the microfluidic system, the silicon wafer is exploited to achieve field-effect flow control by grounding the semiconductive silicon medium. When an electric field is applied through the channel, a radial electric potential gradient is created across the silicon dioxide layer that allows for direct control of the zeta potential and the resulting electroosmotic flow (EOF). By configuring this microfluidic system with two power supplies at both ends of the microchannel, the applied electric potentials can be varied for manipulating the polarity and the magnitude of the radial electric potential gradient across the silicon dioxide layer. At the same time, the longitudinal potential gradient through the microchannel, which is used to induce EOF, is held constant. The results of EOF control in this hybrid microfluidic system are presented for phosphate buffer at pH 3 and pH 5. It is also demonstrated that EOF control can be performed at higher solution pH of 6 and 7.4 by modifying the silicon wafer surface with cetyltrimethylammonium bromide (CTAB) prior to assembly of the hybrid microfluidic system. Results of EOF control from this study are compared with those reported in the literature involving the use of other microfluidic devices under comparable solution conditions.

To miniaturize high-performance membrane chromatography, a poly(vinylidene fluoride) membrane medium, employed as the stationary phase, is sandwiched between two poly(dimethylsiloxane) substrates containing the microchannels. The microchannels are fabricated by the capillary molding technique, involving the use of capillaries as the channel template and the fluid inlet/outlet. The micro(micro)-membrane chromatography system is coupled with a micro-enzyme reactor containing immobilized trypsins for performing rapid protein digestion, peptide separation, and protein identification using electrospray ionization mass spectrometry. Separation performance of cytochrome c digest in micro-membrane chromatography is compared with the results obtained from a regular reversed-phase micro-liquid chromatography. The efficacy and the potentials of micro-membrane chromatography in tryptic mapping are reported. On-line integration of the micro-enzyme reactor with micro-chromatographic separation techniques and electrospray ionization mass spectrometry clearly provides a microanalytical platform for automated sample handling, minimized sample loss, and reduced sample consumption. It also provides enhanced detection sensitivity and dynamic range for the analysis of complex protein mixtures such as cell lysates in proteomics research.

An integrated platform is presented for rapid and sensitive protein identification by on-line protein digestion and analysis of digested proteins using electrospray ionization mass spectrometry or transient capillary isotachophoresis/capillary zone electrophoresis with mass spectrometry detection. A miniaturized membrane reactor is constructed by fabricating the microfluidic channels on a poly(dimethylsiloxane) substrate and coupling the microfluidics to a poly(vinylidene fluoride) porous membrane with the adsorbed trypsin. On the basis of he large surface area-to-volume ratio of porous membrane media, adsorbed trypsin onto the poly(vinylidene fluoride) membrane is employed for achieving ultrahigh catalytic turnover. The extent of protein digestion in a miniaturized membrane reactor can be directly controlled by the residence time of protein analytes inside the trypsin-adsorbed membrane, the reaction temperature, and the protein concentration. The resulting peptide mixtures can either be directly analyzed using electrospray ionization mass spectrometry or further concentrated and resolved by electrophoretic separations prior to the mass spectrometric analysis. This microfluidic system enables rapid identification of proteins in minutes instead of hours, consumes very little sample (nanogram or less), and provides on-line interface with upstream protein separation schemes for the analysis of complex protein mixtures such as cell lysates.

For this work, two different plastic microfluidic devices are designed and fabricated for applications in high-throughput residue analysis of food contaminants and drug screening of small-molecule libraries. Microfluidic networks on copolyester and poly(dimethylsiloxane) substrates are fabricated by silicon template imprinting and capillary molding techniques. The first device is developed to perform affinity capture, concentration, and direct identification of targeted compounds using electrospray ionization mass spectrometry. Poly(vinylidene fluoride) membranes sandwiched between the imprinted copolyester microchannels in an integrated platform provide continuous affinity dialysis and concentration of a reaction mixture containing aflatoxin B1 antibody and aflatoxins. The second microfluidic device is composed of microchannels on the poly(dimethylsiloxane) substrates. The device is designed to perform miniaturized ultrafiltration of affinity complexes of phenobarbital antibody and barbiturates, including the sequential loading, washing, and dissociation steps. These microfabricated devices not only significantly reduce dead volume and sample consumption but also increase the detection sensitivity by at least 1-2 orders of magnitude over those reported previously. Improvements in detection sensitivity are attributed to analyte preconcentration during the affinity purification step, limited analyte dilution in the microdialysis junction, minimal sample loss, and the amenability of ESI-MS to nanoscale sample flow rates.

A new plastic imprinting method using a silicon template is demonstrated. This new approach obviates the necessity of heating the plastic substrate during the stamping process, thus improving the device yield from approximately 10 devices to above 100 devices per template. The dimensions of the imprinted microchannels were found to be very reproducible, with variations of less than 2%. The channel depths were dependent on the pressures applied and the materials used. Rather than bonding the open channels with another piece of plastic, a flexible and adhesive poly(dimethylsiloxane) film is used to seal the microchannels, which offers many advantages. As an application, isoelectric focusing of green fluorescence protein on these plastic microfluidic devices is illustrated.

On-line capillary isoelectric focusing (CIEF)-electrospray ionization - mass spectrometry (ESI-MS) as a two-dimensional separation system is employed for high resolution analysis of ovalbumin phosphorylation. On the basis of their differences in isoelectric point (pI), the mono- and diphosphoovalbumins are separated and resolved in CIEF. The focused protein zones of mono- and diphosphoovalbumins are eluted by combining gravity with cathodic mobilization. At the end of the CIEF capillary, the mobilized ovalbumin zones are analyzed by mass spectrometry coupled on-line to an electrospray interface with a coaxial sheath flow configuration. Additional ovalbumin variants within each of the mono- and diphosphoovalbumins, differing in their molecular masses due to glycosylation microheterogeneity, are easily distinguished by ESI-MS.

Rapid growth in the biotechnology industry has led to a dramatic increase in attention to the protein folding problem. Understanding protein-folding pathways is essential to the production of biopharmaceuticals since commercial production of recombinant proteins often requires a protein-refolding process for recovery of high yields. Protein folding coupled to the formation of disulfide bonds presents one of the simplest approaches to studying folding intermediates. On-line capillary isoelectric focusing-electrospray ionization mass spectrometry (CIEF-ESIMS) is demonstrated for kinetic studies of disulfide bond-induced protein refolding. Refolding intermediates of bovine pancreatic ribonuclease A, a model system for this study, are blocked at different stages by alkylating free thiols with iodoacetate. The alkylation reaction results in the introduction of charge (-1) and mass (59) differences for each alkylation site, providing the means for predictable separation and direct identification of refolding intermediates using CIEF-ESIMS. Besides the observation of refolding intermediates containing different numbers of disulfide bonds and even mixed disulfides, the two-dimensional resolving power of CIEF-ESIMS allows the determination of conformational heterogeneity among groups of refolding intermediates.

The introduction of an enzyme array-electrochemical detection method for carbohydrate analysis is demonstrated by using two complex and one high mannose N-linked oligosaccharides. Instead of measuring the remaining uncleaved oligosaccharides in enzymatic digestion, released monosaccharides are directly quantified by pulsed amperometric detection at a gold electrode. The measured monosaccharide concentrations in combination with the enzyme array analysis provide structural characterization of oligosaccharides. The enzyme array-electrochemical detection method does not require any separation procedure or any prior labeling of oligosaccharides. However, this method is limited by the use of purified oligosaccharide samples and the nature of the enzyme array. The development of more sophisticated enzyme arrays relies upon the introduction of a bank of highly specific (bond, arm, aglycon) exoglycosidases.

Capillary zone electrophoresis (CZE) equipped with laser-induced fluorescence detection (UFO) allows rapid and sensitive identification of folding and aggregation intermediates of P22 tailspike endorhamnosidase using the intrinsic tryptophan fluorescence. Conversion of the protrimer into the native tailspike protein, which is the rate-limiting step, can be quenched at 0 °C and results in a loss of the protrimer in the refolding pathway. Results obtained from CZE.UFD and polyacrylamide gel electrophoresis indicate the loss of folding intermediates through the adsorption of polypeptide chains onto the wall of the refoldingvial. Early aggregation intermediates are studied using a temperature-sensitive folding tailspike mutant which shifts productive folding to the aggregation pathway at restrictive temperatures. By monitoring refolding intermediates during the temperature shift experiments, the early monomeric intermediate is identified as the thermolabile junctional intermediate between the productive and aggregation pathways. After passing the stage for accumulation of thermolabile intermediate, an increase in refolding temperature from 10 to 35 °C is carried out for achieving the optimal refolding kinetics and yields of tailspike endorhamnosidase.