Search

Abstract Background Evidence on the effects of plantar intrinsic foot muscle exercise in older adults remains limited. This study aimed to evaluate the effect of an integrated intrinsic foot muscle exercise program with a novel three-dimensional printing foot core training device on balance and body composition in community-dwelling adults aged 60 and above. Methods A total of 40 participants aged ≥ 60 years were enrolled in this quasi-experimental, single-group, pretest-posttest design; participants were categorized into two groups, those with balance impairment and those without balance impairment. The participants performed a 4-week integrated intrinsic foot muscle exercise program with a three-dimensional printing foot core training device. The short physical performance battery (SPPB) and timed up and go test were employed to evaluate mobility and balance. A foot pressure distribution analysis was conducted to assess static postural control. The appendicular skeletal muscle mass index and fat mass were measured by a segmental body composition monitor with bioelectrical impedance analysis. The Wilcoxon signed rank test was used to determine the difference before and after the exercise program. Results Among the 40 enrolled participants (median age, 78.0 years; female, 80.0%; balance-impaired group, 27.5%), the 95% confidence ellipse area of the center of pressure under the eyes-closed condition was significantly decreased (median pretest: 217.3, interquartile range: 238.4; median posttest: 131.7, interquartile range: 199.5; P = 0.001) after the exercise. Female participants without balance impairment demonstrated a significant increase in appendicular skeletal muscle mass index and a decrease in fat mass. Participants in the balance-impaired group exhibited a significant increase in SPPB. Conclusions Integrated intrinsic foot muscle exercise with a three-dimensional printing foot core training device may improve balance and body composition in adults aged 60 and above. Trial registration ClinicalTrials.gov ID: NCT05750888 (retrospectively registered 02/03/2023).

Individuals with cervical spinal cord injury (C-SCI) often use a tenodesis grip to compensate for their hand function deficits. Although clinical evidence confirms that assistive devices can help achieve hand function improvements, the currently available devices have some limitations in terms of their price and accessibility and the difference in the user’s muscle strength. Therefore, in this study, we developed a 3D-printed wrist-driven orthosis to improve the gripping effect and tested the feasibility of this device by assessing its functional outcomes. A total of eight participants with hand function impairment due to a C-SCI were enrolled, and a wrist-driven orthosis with a triple four-bar linkage was designed. The hand function of the participants was assessed before and after they wore the orthosis, and the outcomes were assessed using a pinch force test, a dexterity test (Box and block test, BBT), and a Spinal Cord Independence Measure Version III questionnaire. In the results, before the participants wore the device, the pinch force was 0.26 lb. However, after they wore the device, it increased by 1.45 lb. The hand dexterity also increased by 37%. After 2 weeks, the pinch force increased by 1.6 lb and the hand dexterity increased by 78%. However, no significant difference was observed in the self-care ability. The results showed that this 3D-printed device with a triple four-bar linkage for individual with C-SCI improved pinch strength and hand dexterity in these patients, but did not improve their self-care ability. It may help patient in the early stages of C-SCI to learn and use the tenodesis grip easily. However, the usability of the device in daily life needs further research.

Finger extension stiffness is a common post-traumatic complication that results in the hand’s functional impairment. In clinical practice, a dynamic splint enables the patient to stretch the affected finger independently. However, current dynamic splints have drawbacks, such as limited stretching efficacy, and interfere with the hand’s functional activities. Therefore, this study aimed to develop a dynamic finger flexion orthosis capable of stretching each finger joint using additive manufacturing (AM) technology, thereby enabling hand functional activity, and analyze the clinical improvement in the range of motion (ROM). One subject with a hand fracture was recruited while undergoing a 7-week home-based rehabilitation program for the orthosis. The outcome measurements included the total active motion (TAM), the tip-to-finger distance (TPD), and the score on the Disability of Arm, Shoulder, and Hand (DASH) questionnaire. The results show that the TAM of the participant’s fingers increased by 72.7 degrees on average, the TPD decreased by 3.5 cm on average, and the DASH score decreased to 9.5 points. The 7-week home-based rehabilitation program for the orthosis resulted in a 53.6% increase in the TAM on average. The developed orthosis improved hand function and enabled a more complete ROM in finger flexion.

Introduction: There are various surgical interventions to manage osteoporotic vertebral compression fracture. Modular spine block (MSB) is a novel intravertebral fixator that can be assembled. This study aimed to quantitatively investigate the force distribution in vertebrae with the various structural designs and implantation methods by finite element analysis (FEA). Methods: A three-dimensional nonlinear FEA of the L3 implanted with MSB was constructed. Different structural designs (solid vs. hollow) and implantation methods (three-layered vs. six-layered and unilateral vs. bilateral) were studied. The model was preloaded to 150 N-m before the effects of flexion, extension, torsion, and lateral bending were analyzed at the controlled ranges of motion of 20°, 15°, 8°, and 20°, respectively. The resultant intervertebral range of motion (ROM) and disk stress as well as intravertebral force distribution were analyzed at the adjacent segments. Results: The different layers of MSB provided similar stability at the adjacent segments regarding the intervertebral ROM and disk stress. Under stress tests, the force of the solid MSB was shown to be evenly distributed within the vertebrae. The maximum stress value of the unilaterally three-layered hollow MSB was generally lower than that of the bilaterally six-layered solid MSB. Conclusions: The MSB has little stress shielding effect on the intervertebral ROM and creates no additional loading to the adjacent disks. The surgeon can choose the appropriate numbers of MSB to fix vertebrae without worrying about poly(methyl methacrylate) extravasation, implant failure, or adjacent segment disease.

Abstract Background The spinal hybrid elastic (SHE) rod dynamic stabilization system can provide sufficient spine support and less adjacent segment stress. This study aimed to investigate the biomechanical effects after the internal fracture of SHE rods using finite element analysis. Methods A three-dimensional nonlinear finite element model was developed. The SHE rod comprises an inner nitinol stick (NS) and an outer polycarbonate urethane (PCU) shell (PS). The fracture was set at the caudal third portion of the NS, where the maximum stress occurred. The resultant intervertebral range of motion (ROM), intervertebral disc stress, facet joint contact force, screw stress, NS stress, and PCU stress were analyzed. Results When compared with the intact spine model, the overall trend was that the ROM, intervertebral disc stress, and facet joint force decreased in the implanted level and increased in the adjacent level. When compared with the Ns-I, the trend in the Ns-F decreased and remained nearly half effect. Except for torsion, the PS stress of the Ns-F increased because of the sharing of NS stress after the NS fracture. Conclusions The study concluded the biomechanical effects still afford nearly sufficient spine support and gentle adjacent segment stress after rod fracture in a worst-case scenario of the thinnest PS of the SHE rod system.

Patients with chronic stroke often have difficulty opening their hands and performing grasping movements. Several passive hand orthoses for assisting hand rehabilitation have been developed and demonstrated to be clinically effective. However, current devices have several limitations, such as supporting only a single grasping motion and using an abnormal grasping posture. Therefore, this study developed a three-dimensional (3D)-printed multifunctional hand device (3DP-MFHD) to solve these problems and evaluated the feasibility of using the device during home rehabilitation. Six participants were enrolled, and each of them was provided with the 3DP-MFHD. In addition to a task-oriented training course, the participants were asked to train at home for 4 weeks for at least 5 days per week and 40 min per day. The results revealed that hand grip force increased by 36.1%, lateral pinch force increased by 17.6%, and the Action Research Arm Test score increased by 54.1%. The 3DP-MFHD is a promising means to facilitate hand rehabilitation and improve hand strength and function in patients with chronic stroke. The 3DP-MFHD can be used as part of home rehabilitation.

Lumbar spondylolysis involves anatomical defects of the pars interarticularis, which causes instability during motion. The instability can be addressed through instrumentation with posterolateral fusion (PLF). We developed a novel pedicle screw W-type rod fixation system and evaluated its biomechanical effects in comparison with PLF and Dynesys stabilization for lumbar spondylolysis via finite element (FE) analysis. A validated lumbar spine model was built using ANSYS 14.5 software. Five FE models were established simulating the intact L1–L5 lumbar spine (INT), bilateral pars defect (Bipars), bilateral pars defect with PLF (Bipars_PLF), Dynesys stabilization (Bipars_Dyn), and W-type rod fixation (Bipars_Wtyp). The range of motion (ROM) of the affected segment, the disc stress (DS), and the facet contact force (FCF) of the cranial segment were compared. In the Bipars model, ROM increased in extension and rotation. Compared with the INT model, Bipars_PLF and Bipars_Dyn exhibited remarkably lower ROMs for the affected segment and imposed greater DS and FCF in the cranial segment. Bipars_Wtyp preserved more ROM and generated lower stress at the cranial segment than Bipars_PLF or Bipars_Dyn. The injury model indicates that this novel pedicle screw W-type rod for spondylolysis fixation could return ROM, DS, and FCF to levels similar to preinjury.

Mechanisms underlying exercise-induced muscle fatigue and recovery are dependent on peripheral changes at the muscle level and improper control of motoneurons by the central nervous system. In this study, we analyzed the effects of muscle fatigue and recovery on the neuromuscular network through the spectral analysis of electroencephalography (EEG) and electromyography (EMG) signals. A total of 20 healthy right-handed volunteers performed an intermittent handgrip fatigue task. In the prefatigue, postfatigue, and postrecovery states, the participants contracted a handgrip dynamometer with sustained 30% maximal voluntary contractions (MVCs); EEG and EMG data were recorded. A considerable decrease was noted in EMG median frequency in the postfatigue state compared with the findings in other states. Furthermore, the EEG power spectral density of the right primary cortex exhibited a prominent increase in the gamma band. Muscle fatigue led to increases in the beta and gamma bands of contralateral and ipsilateral corticomuscular coherence, respectively. Moreover, a decrease was noted in corticocortical coherence between the bilateral primary motor cortices after muscle fatigue. EMG median frequency may serve as an indicator of muscle fatigue and recovery. Coherence analysis revealed that fatigue reduced the functional synchronization among bilateral motor areas but increased that between the cortex and muscle.

The spinal hybrid elastic (SHE) rod is a semi-rigid pedicle screw-based rod for spinal dynamic stabilization. This study investigated the biomechanical effects of different ratios of SHE rod using finite element analysis (FEA). A three-dimensional nonlinear FEA of an intact lumbar spine model (INT) was constructed. The SHE rod was composed of an inner nitinol stick (NS) and an outer polycarbonate urethane shell (PS). Four groups implanted at L3–L4 had the same outer diameter (5.5 mm) but different NS diameter/PS thickness ratios: Nt45, Nt35, Nt25, and Nt15. The resultant intervertebral range of motion (ROM), disc stress, facet joint contact force, screw stress, NS stress, and PCU stress were analyzed. The results indicated that ROM, disc stress, and facet force decreased moderately in the implanted L3–L4 levels and increased slightly in the adjacent L2–L3 levels. The NS stress and NS diameter trended towards inverse proportionality. Changing the ratio did not markedly influence screw or PS stress. The SHE rod system with elastic NS and insulated PS has a 5.5 mm diameter for universal pedicle screws. The SHE rod system provides sufficient spinal support and increases gentle adjacent segment stress. Considering the durability, the optimal NS diameter/PS thickness ratio of the SHE rod system is 3.5/2.0 mm.

Insoles play an important role in the conservative treatment of functional flat foot. The features of 3D-printed insoles are high customizability, low cost, and rapid prototyping. However, different designed insoles tend to have different effects. The study aimed to use 3D printing technology to fabricate three different kinds of designed insoles in order to compare the biomechanical effects on the lower extremities in flat foot participants. Ten participants with functional flat foot were recruited for this study. Data were recorded via a Vicon motion capture system and force plates during walking under four conditions: without insoles (shoe condition), with auto-scan insoles (scan condition), with total contact insoles (total condition), and with 5-mm wedge added total contact insoles (wedge condition). The navicular height, eversion and dorsiflexion angles of the ankle joint, eversion moment of the ankle joint, and adduction moment of the knee joint were analyzed, and comfort scales were recorded after finishing the analysis. Compared to the shoe condition, all three 3D printed insoles could increase the navicular height and ankle dorsiflexion angle and improve comfort. Among the three insoles, the wedge condition was the most efficient in navicular height support and increasing the ankle dorsiflexion angle.

Abstract Background An interspinous process device, the Device for Intervertebral Assisted Motion (DIAM™) designed to treat lumbar neurogenic disease secondary to the lumbar spinal stenosis, it provides dynamic stabilization after minimally invasive (MI) lumbar decompression. The current study was conducted using an experimentally validated L1-L5 spinal finite element model (FEM) to evaluate the limited decompression on range of motion (ROM) and stress distribution on a neural arch implanted with the DIAM. Methods The study simulated bilateral laminotomies with partial discectomy at L3-L4, as well as unilateral and bilateral laminotomies with partial discectomy combined with implementation of the DIAM at L3-L4. The ROM and maximum von Mises stresses in flexion, extension, lateral bending, and axial torsion were analyzed in response to the hybrid protocol in comparison with the intact model. Results The investigation revealed that decreased ROM, intradiscal stress, and facet joint force at the implant level, but considerably increased stress at the pars interarticularis were found during flexion and torsion at the L4, as well as during extension, lateral bending, and torsion at the L3, when the DIAM was implanted compared with the defect model. Conclusion The results demonstrate that the DIAM may be beneficial in reducing the symptoms of stress-induced low back pain. Nevertheless, the results also suggest that a surgeon should be cognizant of the stress redistribution at the pars interarticularis results from MI decompression plus the application of the interspinous process device.

Minimally invasive decompression is generally employed for treating lumbar spinal stenosis; however, it results in weakened spinal stability. To augment spinal stability, a new interspinous process device (NIPD) was developed in this study. The biomechanical features of the NIPD were evaluated in this study. Three finite-element (FE) models of the entire lumbar spine were implemented to perform biomechanical analysis: the intact, defect (DEF), and NIPD models. The DEF model was considered for lumbar spines with bilateral laminotomies and partial discectomy at L3–L4. Range of motion (ROM), disc stress, and facet joint contact force were evaluated in flexion, extension, torsion, and lateral bending in the three FE models. The results indicated that ROM in the extension increased by 23% in the DEF model but decreased by 23% in the NIPD model. In the NIPD model, the cephalic adjacent disc stress in flexion and extension was within 5%, and negligible changes were noted in the facet joint contact force for torsion and lateral bending. Thus, the NIPD offers superior spinal stability and causes only a minor change in cephalic adjacent disc stress in flexion and extension during the bilateral laminotomy and partial discectomy of the lumbar spine. However, the NIPD has a minor influence on the ROM and facet joint force for lateral bending and torsion.

Kinesio taping has been used to improve sensorimotor control performance. In this study, we explored the effect of Kinesio taping with different tensions on hand force control, joint proprioception, reaction time and brain activity. This was an observational study with a single-group, repeated-measures design. Twenty-four healthy participants (12 women) randomly assigned to three wrist/finger flexor taping conditions: (1) taping with 20% additional tension (taping20), (2) taping with neutral tension (tapingN), and (3) without taping (control). Grip force and wrist joint proprioceptive senses, reaction time, and force control performance were recorded in each of the taping conditions. An EEG of the bilateral sensorimotor cortex and an EMG of the right finger flexors were recorded to investigate changes in brain activity and functional connectivity between the brain and muscles (coherence). Our results indicated that taping significantly improved the joint position sense for participants with an error >3° (control vs. tapingN vs. taping20: 4.1° ± 1.04° vs. 2.6° ± 0.97° vs. 2.1° ± 0.91°; p = 0.001). In addition, Kinesio taping-induced improvements in force control were moderately correlated with decreases in the EEG beta band power. In conclusion, Kinesio taping could improve the joint proprioceptive sense, and taping-induced improvement in force control is likely due to neural desynchronization in motor cortex.

Foot orthoses (FOs) are commonly used as interventions for individuals with flatfoot. Advances in technologies such as three-dimensional (3D) scanning and 3D printing have facilitated the fabrication of custom FOs. However, few studies have been conducted on the mechanical properties and biomechanical effects of 3D-printed FOs. The purposes of this study were to evaluate the mechanical properties of 3D-printed FOs and determine their biomechanical effects in individuals with flexible flatfoot. During mechanical testing, a total of 18 FO samples with three orientations (0°, 45°, and 90°) were fabricated and tested. The maximum compressive load and stiffness were calculated. During a motion capture experiment, 12 individuals with flatfoot were enrolled, and the 3D-printed FOs were used as interventions. Kinematic and kinetic data were collected during walking by using an optical motion capture system. A one-way analysis of variance was performed to compare the mechanical parameters among the three build orientations. A paired t-test was conducted to compare the biomechanical variables under two conditions: walking in standard shoes (Shoe) and walking in shoes embedded with FOs (Shoe+FO). The results indicated that the 45° build orientation produced the strongest FOs. In addition, the maximum ankle evertor and external rotator moments under the Shoe+FO condition were significantly reduced by 35% and 16%, respectively, but the maximum ankle plantar flexor moments increased by 3%, compared with the Shoe condition. No significant difference in ground reaction force was observed between the two conditions. This study demonstrated that 3D-printed FOs could alter the ankle joint moments during gait.

This paper proposes a point cloud alignment algorithm based on stereo vision using Random Pattern Projection (RPP). In the application of stereo vision, it is rather difficult to find correspondences between stereo images of texture-less objects. To overcome this issue, RPP is used to enhance the object’s features, thus increasing the accuracy of the identified correspondences of the stereo images. In the 3D alignment algorithm, the down sample technique is used to filter out the outliers of the point cloud data to improve system efficiency. Furthermore, the extracted features of the down sample point cloud data were applied in the matching process. Finally, the object’s pose was estimated by the alignment algorithm based on object features. In experiments, the maximum error and standard deviation of rotation are respectively about 0.031°and 0.199°, while the maximum error and standard deviation of translation are respectively about 0.565 mm and 0.902 mm . The execution time for pose estimation is about 230ms.

Ankle foot orthosis (AFO) is widely used to prevent foot drop and improve walking ability for individuals with cerebral palsy and stroke. However, traditional anterior AFO (TAAFO) could only last within months because the bilateral neck of TAAFO was easy to break. Currently, a 3D-printing technique is used to develop assistive devices for rehabilitation. The study aimed to implement the finite element (FE) method to revise the 3D printed AAFO (3DP-AAFO) and evaluate its strength. A 3.2 mm-thickness for the TAAFOs and 3DP-AAFOs were fabricated, respectively. The stiffness of TAAFO and 3DP-AAFO were tested by a material machine and compared to the FE model. In the FE analysis, the thickness of AAFO model was increased at the neck to enhance its strength. A plantarflexion and dorsiflexion moment were respectively subjected to 3DP-AAFO models to undergo stress analysis. Under the mechanical test, the 3DP-AAFO (K = 1.09 Nm/degree) was 7.8 times stiffer than the traditional AAFO (K = 0.14 Nm/degree). The FE results showed that thickening the 3DP-AAFO on the neck up to 4.7 mm could moderate stress concentration and increase the stiffness of the 3DP-AAFO. Therefore, the study concluded that the 3DP-AAFO was stiffer than the traditional AAFO. Increasing the appropriate thickness around neck of 3DP-AAFO could avoid neck fracture as much as possible.

Interbody fusion with posterior instrumentation is a common method for treating lumbar degenerative disc diseases. However, the high rigidity of the fusion construct may produce abnormal stresses at the adjacent segment and lead to adjacent segment degeneration (ASD). As such, biodegradable implants are becoming more popular for use in orthopaedic surgery. These implants offer sufficient stability for fusion but at a reduced stiffness. Tailored to degrade over a specific timeframe, biodegradable implants could potentially mitigate the drawbacks of conventional stiff constructs and reduce the loading on adjacent segments. Six finite element models were developed in this study to simulate a spine with and without fixators. The spinal fixators used both titanium rods and biodegradable rods. The models were subjected to axial loading and pure moments. The range of motion (ROM), disc stresses, and contact forces of facet joints at adjacent segments were recorded. A 3-point bending test was performed on the biodegradable rods and a dynamic bending test was performed on the spinal fixators according to ASTM F1717-11a. The finite element simulation showed that lumbar spinal fusion using biodegradable implants had a similar ROM at the fusion level as at adjacent levels. As the rods degraded over time, this produced a decrease in the contact force at adjacent facet joints, less stress in the adjacent disc and greater loading on the anterior bone graft region. The mechanical tests showed the initial average fatigue strength of the biodegradable rods was 145 N, but this decreased to 115N and 55N after 6 months and 12 months of soaking in solution. Also, both the spinal fixator with biodegradable rods and with titanium rods was strong enough to withstand 5,000,000 dynamic compression cycles under a 145 N axial load. The results of this study demonstrated that biodegradable rods may present more favourable clinical outcomes for lumbar fusion. These polymer rods could not only provide sufficient initial stability, but the loss in rigidity of the fixation construct over time gradually transfers loading to adjacent segments.

Background: The dynamic Dynesys Stabilization System preserves lumbar mobility at instrumented levels. This study investigated the effect of screw length on screw loosening (SL) after dynamic Dynesys fixation and screw displacement during lumbar motion, using clinical investigation and finite-element (FE) analysis. Methods: Clinical data of 50 patients with degenerative spondylolisthesis treated with decompression and Dynesys fixation in 2011 were analyzed retrospectively. Horizontal sliding displacement and vertical displacement of screw tips at L4 were analyzed postoperatively using displacement-controlled FE analysis at the L4-L5 level with screw lengths 45 (long screw), 36 (median screw), and 27 (short screw), and 6.4 mm in diameter, under flexion, extension, lateral bending, and rotation. Results: In 13 patients (13/50, 26%), 40 screws (40/266, 15%) were loose at mean follow-up of 101.3 ± 4.4 months. Radiographic SL at 35, 40, 45, and 50 mm were 7.7%, 10.7%, 12.1%, and 37.5%, respectively, regardless of the fixation level (p = 0.009). FE analysis revealed that the long screw model with corresponding longer lever arm had maximal horizontal sliding displacement under all directions and maximal vertical displacement, except for lateral bending. Conclusion: Shorter screws in Dynesys fixation may help avoid dynamic SL. Clinically, 50 mm screws showed the greatest SL and median screw screws demonstrated the least displacement biomechanically. [ABSTRACT FROM AUTHOR]

Purpose: The aim of the present study was to compare the biomechanical effects of different lengths of implants in an immediate loading condition in mandibular and fibular bone. Three-dimensional (3D) nonlinear finite element analysis (FEA) was used to examine the complex irregular structures. The variables of this research were the two different bone types (mandible and fibula) and three different implant lengths. Materials and Methods: Simplified half models were constructed for 3D FEA. Three different implant lengths (6 mm, 10 mm, and 15 mm) were inserted into the mandibular and fibular bone models, which were made to simulate immediate implant loading conditions. A load of 125 N was applied to the center of the suprastructure at a 45-degree angle relative to the long axis of the implant, and the resultant maximum von Mises equivalent (EQV) stresses, stress distribution, strain energy, and micromotion were measured. Results: In the mandible, the maximum EQV stresses were 115.636 MPa, 155.943 MPa, and 157.105 MPa with the 6-mm, 10-mm, and 15-mm implants, respectively. The mean EQV stresses were 64.145 MPa, 77.925 MPa, and 78.500 MPa, respectively. In the fibula, the maximum EQV stresses were 174.04 MPa, 157.456 MPa, and 144.353 MPa with the 6-mm, 10-mm, and 15-mm implants, respectively. The mean EQV stresses were 82.329 MPa, 73.526 MPa, and 74.050 MPa, respectively. Conclusion: The micromotion in the fibula models was lower than that seen in the mandible models. EQV stress in the fibular bone was different from that in the mandible. Short implants can be an option for oral rehabilitation in the mandible; however, implants in the fibula should probably have bicortical engagement. [ABSTRACT FROM AUTHOR]

Purpose: The objective of this study was to analyze and compare the stresses in two different bone-implant interface conditions in anisotropic three-dimensional finite element models (FEMs) of an osseointegratedimplant of either commercially pure titanium or yttrium-partially stabilized zirconia (Y-PSZ) in combination with different superstructures (gold alloy or Y-PSZ crown) in the posterior maxilla. Materials and Methods:Three-dimensional FEMs were created of a first molar section of the maxilla into which was embedded an implant, connected to an abutment and superstructure, using commercial software. Two versions of the FEM were constructed; these allowed varying assignment of properties (either a bonded and or a contact interface), so that all experimental variables could be investigated in eight groups. Compact and cancellous bone were modeled as fully orthotropic and transversely isotropic, respectively. Oblique (200-N vertical and 40-N horizontal) occlusal loading was applied at the central and distal fossae of the crown. Results:Maximum von Mises and compressive stresses in the compact bone in the two interfaces were lower in the zirconia implant groups than in the titanium implant groups. A similar pattern of stress distribution in cancellous bone was observed, not only on the palatal side of the platform but also in the apical area of both types of implants. Conclusion: The biomechanical parameters of the new zirconia implant generated a performance similar to that of the titanium implant in terms of displacement, stresses on the implant, and the bone-implant interface; therefore, it may be a viable alternative, especially for esthetic regions. Int J Oral Maxillofac Implants 2012;27:e49-e57. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the influence of implant collar geometry on the distribution of stress and strain in the crestal compact bone contiguous to an implant collar for four types of bone under axial and oblique loads. Materials and Methods: Finite element models of threaded implants with three kinds of implant collar designs (divergent, straight, and convergent) with their corresponding suprastructures embedded in the posterior mandible were created with ANSYS software. Eight different test conditions incorporating four types of bone (orthotropic and effectively isotropic in part 1 and high and low densities in part 2) under separate 100-N axial and 35.6-degree oblique forces were created to investigate the stress and strain distributions in the crestal compact bone around the implant collars. Results: In all eight conditions, the divergent collar demonstrated the lowest maximum von Mises and principal stresses and strains in the crestal compact bone contiguous to the implant collar, followed by the straight and convergent collars. The oblique load induced higher peak values than the axial load. The orthotropic design amplified and increased the pathologic microstrains and tensile stresses in the crestal compact bone compared to the effectively isotropic design, especially in models with a convergent collar design. In part 2 of the study, the maximum von Mises stresses and strains increased with a decrease in the cancellous bone density. Under oblique loading, the convergent and straight collars showed pathologic microstrain values as well as excessive ultimate tensile stresses in the orthotropic bone model with low-density cancellous bone. Conclusions: Within the limitations, it was concluded that stress and strain distributions in the adjacent compact bone are influenced by the implant collar design. The divergent implant collar design was associated with the lowest stress and strain concentrations in the crestal compact bone. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study was to analyze and compare the implant-bone interface stresses in anisotropic three-dimensional finite element models of an osseointegrated implant with platform switching and a conventional matching-diameter implant platform and abutment in the posterior maxilla. Materials and Methods: Three-dimensional finite element models were created of a first molar section of the maxilla and embedded with a single endosseous implant (4.1 × 10 mm). One model simulated a 4.1-mm-diameter abutment connection and the other was a narrower 3.4-mm-diameter abutment connection, ie, simulating a platform-switching configuration. A gold alloy crown with 2-mm occlusal thickness was applied over the titanium abutment. Material properties of compact and cancellous bone were modeled as fully orthotropic and transversely isotropic, respectively. Oblique (200-N vertical and 40-N horizontal) occlusal loads were applied and perfect bonding was assumed at all interfaces. Results: Maximum von Mises, compressive, and tensile stresses in compact bone were lower in the platform-switching model than in the conventional model. However, the maximum von Mises stress in cancellous bone was higher in the platform-switching model than in the conventional model. Conclusion: The platform-switching technique reduced the stress concentration in the area of compact bone and shifted it to the area of cancellous bone during oblique loading. [ABSTRACT FROM AUTHOR]

Context: Fatigue of the shoulder rotator muscles may negatively affect joint position sense (JPS) and ultimately lead to injury. Objective: Recovery of shoulder JPS after muscle fatigue. Design: A repeated-measures study. Setting: Musculoskeletal research laboratory. Patients: Thirteen subjects participated in joint position error tests and isokinetic concentric strength assessment in shoulder rotation, before and after rotator muscle fatigue. Interventions: Local muscle fatigue was induced using isokinetic concentric contractions of the shoulder rotator muscles. Main Outcome Measurements: Shoulder rotator strength and JPS error signals were measured before fatigue, immediately after fatigue, and every ten minutes thereafter for one hour. Results: Before shoulder rotation muscle fatigue, the accuracy of shoulder JPS was 2.79 ± 1.67 degrees. After muscle fatigue, the accuracy decreased to 6.39 ± 2.90 degrees. Shoulder JPS was influenced up to 40 minutes after muscle fatigue, but shoulder strength was only affected for 10 minutes after muscle fatigue. Conclusions: Proprioceptive recovery was slower than strength following fatigue of the shoulder rotators. [ABSTRACT FROM AUTHOR]