Search

Sixth generation (6G) wireless networks operating in terahertz frequency region are significant solutions to the increasing number of telecommunication devices and the demand for faster data transmission. However, few dielectric materials exhibiting an ultralow relative dielectric constant (εr), loss tangent (tanδ), and high mechanical strength are found suited for 6G telecommunication. In this study, we developed lightweight ceramic foams by directly sintering glass hollow spheres. The effects of sintering temperatures on their mechanical performance, and terahertz optical and dielectric properties were systematically investigated. The final compositions of ceramic foams contain glass, cristobalite, quartz, and wollastonite. The crystalline content increases with increasing sintering temperature. The ceramic foams sintered at low temperatures of 700–850°C exhibit a high porosity ranging from 74.6% to 87.3%, ultralow εr ranging from 1.41 to 1.83, and tanδ of ∼0.011 at 0.5 THz, as well as high compressive strength ranging from 10.1 to 27.4 MPa, which could be promising materials for 6G telecommunication. [ABSTRACT FROM AUTHOR]

Microwave and terahertz communications are increasingly significant, however, the lack of material information in terahertz band limits their development. Moreover, few lightweight materials with a high relative dielectric constant (εr) are found suited for satellite communication and wearable devices. In this study, we developed lightweight porous Ba4[(Sm0.1Nd0.9)0.9Bi0.1]28/3Ti18O54 (BSNBT) ceramics exhibiting a total porosity ranging from 6.3% to 26.5% (bulk density ranging from 5.47 to 4.29 g/cm3) and relatively high εr ranging from 85.6 to 56.8, which were obtained by sacrificial template method using polymethyl methacrylate spheres (PMMAs) of varying average particle sizes, from 9 to 34 μm, as sacrificial materials. A high refractive index ranging between 7.5 and 8.9 and a low absorption coefficient of approximately 17 cm−1 at 0.3 THz were obtained for the porous ceramics with different total porosities derived from PMMAs with average particle sizes of 9 and 19 μm. Furthermore, effective medium and Mie scattering theories were applied to understand the effects of porous structure on the dielectric properties in microwave and terahertz frequency ranges, respectively, owing to the different wavelengths in the BSNBT matrix. The results of this study suggest that introducing a porous structure can effectively exploit lightweight microwave dielectric ceramic materials and provide valuable information on their terahertz response mechanism. [ABSTRACT FROM AUTHOR]

Ceramic foams with significant porosity and robust mechanical properties have received extensive attentions. However, it is still difficult to achieve excellent compressive strength at high porosity levels. In this work, a gelation of foamed boehmite sol method is proposed to settle this issue. The technological parameters during preparation process are systematically investigated. As‐prepared alumina ceramic foams possess unprecedentedly high compressive strength of 34.1‐89.1 MPa at high porosity levels of 66.0%‐87.2%, which is attributed to the present of hierarchical pore structure, small grain size and pore size. This work demonstrates a facile and novel method for the fabrication of high‐performance alumina ceramic foams toward practical applications. [ABSTRACT FROM AUTHOR]

Abstract: A novel method for fabrication of highly porous barium strontium titanate (BST) ceramic foams based on particle‐stabilized foaming method was developed for the first time, in which propyl gallate (PG) was employed as BST particle modifier. The results showed that the stability of wet BST foams closely depends on the pH value and PG concentration, which could be explained by the adsorption behavior of PG on BST particle surface. BST ceramic foams with dense, uniform, and closed pore and defect‐free wall were obtained. The pore size and porosity can be well controlled by adjusting solid loading and sintering temperature. It was revealed that not only sintering temperature but also solid loading significantly influenced the growth of BST grain. The BST ceramic foams exhibited high porosity in the range of 81%‐95%, low dielectric constant in the range of 47‐150, and low dielectric loss below 0.0025. The BST ceramic foams with higher porosity presented a tendency of lower dielectric constant and the fitting results indicated that the natural logarithm of dielectric constant was linear correlated with porosity. [ABSTRACT FROM AUTHOR]

The weak compressive strength of dried ceramic foams is a disadvantage of fabricating ultralight ceramic foams, especially for the ceramic foams with porosity exceeding 95%. In this study, dried alumina foams were enhanced by agar and PVA-freezing-thawing using sodium dodecyl sulfate as surfactant. It is found that the two additives have no negative influence on adsorption of sodium dodecyl sulfate on alumina particles as well as the hydrophobic character of alumina particles. Stable alumina particle-stabilized foams were prepared with less than 0.5 wt% agar and 1.0 wt% PVA. High additive concentration above the critical values weakens stability of wet foams, which is probably due to the aggregate of alumina particles caused by long-chain molecules connecting. The compressive strength of dried alumina foams has a significant improvement with the employment of agar and PVA-freezing-thawing. The dried foams prepared with 1wt% PVA assisted by freezing-thawing has porosity of 97.1% and compressive strength of 0.16 MPa, which could maintain integrity of dried foams without destruction in the fabricating process. [ABSTRACT FROM AUTHOR]

Low-loss microwave dielectric ceramics are of great significance for fifth-generation telecommunication (5G) devices used for higher frequencies, while reducing the dielectric loss in the microwave band is still a technical challenge. Lattice dynamics and terahertz response are closely related to the polarization of dielectrics, and can be used as effective methods to explore the loss mechanism of microwave dielectrics. Here, Al3+ was doped into the conventional high-permittivity (ε r) Ca 1- x Sm 2 x /3 TiO 3 (x = 0.4) ceramic system, enhancing the Q × f values significantly. Raman spectra, thermally stimulated depolarization currents (TSDC) and terahertz time-domain spectra (THz-TDS) together showed that the stiffness of cation vibration became stronger when z value was larger, indicating a smaller damping of the lattice vibration, and leading to lower extrinsic losses and higher Q × f values. The relationship between lattice dynamics, defect behavior and microwave dielectric loss will provide a significant reference for the development of low-loss microwave dielectric ceramics. • Medium/high- ε r dielectrics of microwave/terahertz devices are developed. • The Q × f values in the microwave and terahertz bands are essentially constant. • Bond strength, defects, lattice vibration and dielectric loss have strong correlation. [ABSTRACT FROM AUTHOR]

• The defect dipoles and oxygen vacancies were supposed to be the main defects in La,Al co-doped (Ba,Sr)La 4 Ti 4 O 15 ceramics. • The oxygen vacancies in the ceramics were affected by the lattice parameters. • The oxygen vacancies in the ceramics dominated the dielectric loss in microwave/terahertz frequency ranges. The thermally-stimulated relaxation of defects in La,Al co-substituted (Ba,Sr)La 4 Ti 4 O 15 dielectric ceramics with hexagonal perovskite structure were investigated systematically with the thermally stimulated depolarization current (TSDC) measurements. The ion substitution decreased the lattice parameters and the bond lengths of the cations and O2−. TSDC spectra indicated the main extrinsic defects in the ceramics were oxygen vacancies and the concentration of oxygen vacancies decreased with the increasing ion substitutions, which was derived from the decrease in the lattice parameters. The terahertz time-domain spectra indicated the damping factor of lattice vibration was reduced with the decline of the concentration of oxygen vacancies, which decreased the microwave/terahertz dielectric loss. High-performance (Ba 0.2 Sr 0.8) 0.75 La 4.25 Ti 3.75 Al 0.25 O 15 (ε r = 43.9, Q × f = 84300 GHz, τ f = -18.0 ppm/°C) ceramics were obtained. The correlations between crystal structures, defect behaviors and dielectric properties discussed in this work could provide guidance for the modification of microwave dielectric ceramics. [ABSTRACT FROM AUTHOR]

Ceramic foams with extensive interconnected pores have great application potential in high‐temperature particulate matter (PM) capture. Considering that there are still challenges to synthesize ceramic foams with efficient filtration, a novel hierarchical‐structured alumina foam with three‐dimensional (3D) reticular architecture has been fabricated via combining chemical grafting pore‐forming agent and polyurethane (PU) foaming technology. Carbon black is grafted with carbamate functional groups in order to enable a better dispersion in highly viscous PU. Submicrometer and micrometer‐sized pores on the cell walls are observed in hierarchical‐structured ceramic foams. The resulting alumina foam exhibits 95.2% removal efficiency for PM particles and low pressure drop of only 50 Pa when grafted carbon black content is 3 wt%. This filtration performance is much higher than that of existing ceramic materials. These features, combined with our experimental design strategy, provide a new insight to design high‐temperature PM filtration materials with durable high performance. [ABSTRACT FROM AUTHOR]

A novel kind of nanowire sponges, namely Si3N4 nanowire‐weaving microspheres, synthesized from a simple, convenient, high‐efficient approach are proposed here. As the reverse template, three‐dimensional foam skeleton structure with uniform pores and ultrathin pore walls is constructed via the effective particle‐stabilized foam method, where the silica sol and carbon black are chosen as the raw materials, providing the sufficient space for the growth of nanowires during the carbothermal reduction reaction process. The formation mechanism of this novel sponge is studied via multiple characterization methods. Si3N4 nanowires formed microspheres possess uniform and curving morphology due to the stable environment for growing via vapor–solid mechanism, leading to the relatively high specific surface area of 86.77 m2/g. Owing to in‐situ oxidation process, micro‐spherical SiO2 nanowire sponges with similar morphology are synthesized, which present diameter in range of 20‐40 nm and specific surface area of 50.47 m2/g. This work provides insights for the design of high‐performance nanowire sponges with promising applications in the filtration, thermal insulators, and catalyst supports fields. [ABSTRACT FROM AUTHOR]

Abstract The mechanical strength of highly porous ceramic foams shows significant attenuation with the increase of porosity, especially for ceramic foams with very high porosity level above 95%. Ultra-light bulk composite ceramic foams were fabricated via introducing 20 wt% zirconia in alumina-based cell wall, aiming at improving mechanical strength of alumina based ceramic foams. The preparation and stability of alumina and zirconia particles synergistically stabilized foams were investigated. The obtained bulk ceramic foams manifested an exciting combination of both high porosity above 96% and excellent specific compressive strength, due to their closed pore structure, defect-free cell wall with uniform thickness, and uniformly distributed zirconia grains in alumina matrix. The alumina/zirconia composite ceramic foams with porosity of 96.7% exhibited compressive strength of 1.11 ± 0.07 MPa, which was much higher than that of alumina ceramic foams in the case of same porosity. [ABSTRACT FROM AUTHOR]

Compressive strength is one of the most important mechanical properties for ceramic foams but the dependence of compressive strength of highly porous ceramic foams on porosity remains unclear up to now, especially for the ceramic foams with porosity above 94%. In this paper, the relationship between compressive strength and porosity of ceramic foams with high porosity in the range of 79–98% was studied for the first time. The alumina ceramic foams and zirconia foams were prepared by particle-stabilized foaming method using sodium dodecyl sulfonate (SDS) as foaming agent. It was found that the function relation between compressive strength and porosity depended on porosity level. Specifically, compressive strength of ceramic foams fitted well with Rice Model when the porosity ranged from 79% to 94%. When the porosity increased above 95%, compressive strength of ceramic foams showed linear relation to porosity, which was probably due to the characteristic of highly porous ceramic foams with thin and lamellate cell wall. [ABSTRACT FROM AUTHOR]

A novel approach to fabricate mullite ceramic foams with high porosity and mechanical strength using fly ash hollow spheres (FAHSs) as the only raw material was reported for the first time, in which FAHSs served as both matrix and pore-forming agent. It was demonstrated that uniform FAHS ceramic foams without cracks could be fabricated by both direct stack sintering method and gel-casting route. The effect of sintering temperature on linear shrinkage, porosity, phase composition and mechanical properties was investigated. With the increase of sintering temperature from 1200 °C to 1350 °C, the fracture mechanism changed from fracturing along FAHSs to fracturing across FAHSs, and the compressive strength of the FAHS ceramic foams increased from 4.4 MPa to 33.4 MPa. The FAHS ceramic foams exhibited high porosity in the range of 73–81% and high mechanical strength, which benefited from the dense assembling of small FAHSs with natural diameter distribution and excellent wall-thickness uniformity. [ABSTRACT FROM AUTHOR]

Hierarchical cellular architectures hold great potential in a vast range of applications due to their superior mechanical properties and multifunctionality. In the present work, hierarchical structures composed of porous struts patterned in the form of quadrangular and triangular honeycombs were fabricated via direct foam writing (DFW) using colloidal particle‐stabilized Al2O3‐MgO‐SiO2 foams as the ink. Hydration process of MgO and subsequent formation of colloidal Mg(OH)2 network endowed the foam ink with viscoelasticity and high storage modulus. The resulting honeycombs with ultrahigh overall porosity (95.3%) and robust compressive strength (2.5 MPa) can be readily fabricated by DFW. The current work exhibits a significant step toward the scalable production of cellular ceramics with hierarchical architecture for various applications, including tissue scaffolds, catalyst supports, thermal insulation, and lightweight structures. [ABSTRACT FROM AUTHOR]

Ultralight ceramics with striking mechanical properties and improved pore connectivity could have wide applications in areas ranging from catalyst support to hot gas filtration. However, creating such materials has proven to be a challenging target. This work demonstrated a novel methodology to prepare porous MgAl 2 O 4 ceramics by calcining gelled MgO–Al 2 O 3 –SiO 2 particle-stabilized foams. The striking green strength of dried foams can be achieved as a consequence of MgO hydration and subsequent formation of gelled Mg(OH) 2 and MgO–SiO 2 –H 2 O skeleton. The decomposition of colloidal substance at elevated temperature resulted in the formation of small pores on the cell wall, thus forming the hierarchical porous architecture and improving the pore connectivity. The highly porous MgAl 2 O 4 ceramics fired at 1600°C possessed the integrated properties of ultrahigh porosity (87.0%), improved pore connectivity and satisfactory compressive strength (7.93 MPa), showing great potential to be used in multiple industrial fields. [ABSTRACT FROM AUTHOR]

Mechanically robust alumina ceramics with low shrinkage were successfully prepared via gelcasting using Isobam as the gelling agent and pre-sintered alumina powder as the raw material for the first time. The influence of amount of pre-sintered alumina powder and powder's pre-sintering temperature on the viscosity of suspension and mechanical properties of low-shrinkage alumina ceramics were systematically investigated. The results showed that low-shrinkage alumina ceramics with flexural strength of 294.5 ± 33.0 MPa, linear shrinkage of 7.79% and relative density of 91.5% can be obtained with the addition of 60 wt% alumina powder pre-sintered at 1600 °C. This convenient and facile approach is promising to fabricate low-shrinkage alumina ceramics with large sizes, high dimensional accuracy and complex shapes. [ABSTRACT FROM AUTHOR]

Ultralight ceramic foam materials with high porosity play an important role in increasingly hi‐tech areas due to the combinative merit of ceramic material and highly porous structure. So far, it remains challenging to fabricate alumina ceramic foams with extremely high porosity and high specific surface area that are comparable to aerogel materials by employing a low cost, eco‐friendly and convenient approach. For the first time, we propose the preparation of aerogel‐like ceramic foams with nanoscale cell wall and unprecedentedly high porosity using boehmite sol as both ceramic source and bubble interface stabilizer, based on sol nanoparticles stabilized foams using sodium lauryl sulfate (SDS) as modifier. The obtained ultra‐stable sol foams allow for the achievement of bulk foams with ultrathin cell wall with thickness in the range of 30‐90 nm, super‐high porosity up to 99%, and large specific surface area of 280 m2/g, which is attributed to the well‐organized assembly of nanoparticles at the liquid/air interfaces. This novel foam material demonstrates excellent adsorption ability for polar volatile organic gases (VOCs) due to its extremely high porosity and large specific surface area. Ultralgiht cellular ceramic foams composed of uniformly assembled nanoparticles with nanoscale cell wall. [ABSTRACT FROM AUTHOR]

Hierarchical structured porous ceramics have attracted tremendous research interests because of their numerous excellent properties including robust mechanical strength and large surface area. In this work, silicon carbide (SiC)‐based porous ceramics with three levels of pore hierarchy are fabricated from silicon particle‐stabilized foams and a subsequent one‐step calcination after they were embedded with coke. Three‐dimensional (3D) flexible nanofibrous network is adhered and wrapped on cell walls of porous ceramics, which is readily fine‐tuned and tailored by the temperature to provide optimized pore structure. The resultant SiC‐based porous ceramics present a density of 1.03 g/cm3 at a porosity of 72% with a large quantity of hierarchical micro‐ and macropores. This hierarchical structure leads to robust compressive strength (23.52 MPa) and large surface area (64.32 m2/g). The fabrication method is straightforward and sought‐after, providing a facile technical route for advanced hierarchical porous ceramics used in filtration and catalysis fields. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • Carbamate functional group was grafted onto carbon black surface. • Hierarchical PACs with 3D reticular architectures were fabricated. • PACs showed superior high-temperature particulate matter filtration. Abstract Porous ceramics with high porosity and extensive interconnected pores have great application potential in fields ranging from dye removal to high-temperature particulate matter (PM) capture. However, constructing these materials to achieve efficient filtration is extremely challenging. Herein, a novel strategy to create hierarchical-structured porous alumina ceramics (PACs) with three-dimensional (3D) reticular architecture is reported based on polyurethane (PU) foaming method. To ensure the efficient flow-through filtration, carbamate-grafted carbon black is used as the pore-forming agent and assembled into the porous PU framework. Submicron and micron-sized pores on the cell walls are observed in hierarchical-structured PACs. This unique structure enables a high PM removal efficiency (94.1%) at an ultralow pressure drop (20 Pa). Our work has demonstrated great application potentials of as-prepared PACs as an efficient high-temperature PM filter and provided new insights to develop highly effective filter. [ABSTRACT FROM AUTHOR]

Abstract In the present work, Al 2 O 3 -Si 3 N 4 porous ceramics with a cactus-like architecture were fabricated by calcining Al 2 O 3 -Si binary particle-stabilized foams in the nitrogen atmosphere. A large number of acicular Si 3 N 4 nanobelts were constructed on the surface of cell walls as a consequence of CVD process to achieve an interlaced network. Such structure was beneficial to realize a high capture efficiency of particulate matters (PM) during filtration. Resultant products having a bulk density of 0.38 g/cm3 at an apparent porosity of 86% can potentially be applied as the air filters in environment field. [ABSTRACT FROM AUTHOR]

Graphical abstract Highlights • Aqueous ceramic particle-stabilized foams with UV light response are prepared. • Photocurable particle-stabilized emulsions with controllable structure are achieved. • The colloid foams/emulsions demonstrate excellent stability and photocuring ability. • Rapid and scalable synthesis of ceramic capsules is developed based on the emulsions. Abstract We herein report the design and preparation of ceramic particle-stabilized emulsions/foams with distinct ultraviolet light (UV) response, which can be used for the rapid fabrication of ceramic foams with complex shape, for synthesis of ceramic hollow spheres, and can potentially be used for 3D printing lightweight and hierarchical ceramics with porous skeleton. Photocurable foams/emulsions stabilized by ceramic particles are achieved for the first time using photosensitive oligomer as oil phase and/or using photosensitive aqueous solution containing acrylamide monomer as water phase. Four kinds of photocurable emulsions are demonstrated by adjusting emulsion structure and photosensitive phase. We further synthesize internal multiple-pore structured capsules and lightweight nanoparticle-assembled capsules in micron-scale based on the photocurable particle-stabilized, by separating emulsion into small droplets via diluting and stirring, followed by rapid curing under UV. This new strategy may potentially open opportunities for the rapid and cost-effective synthesis of high-output ceramic capsule materials. The synthesized thin-shell alumina capsules exhibit large specific area surface of 323.18 m2/g as well as uniform mesoporous structure in shell with average pore diameter of 3.4 nm, which has potential application in the fields of adsorption, load and release of materials and thermal insulation. [ABSTRACT FROM AUTHOR]

Ceramic foams with multi‐scale pores and large specific surface area have received extensive attention due to their unique structure and superior properties. Considering that there are still challenges to synthesize porous ceramics with large specific surface area, a novel ceramic foam material with ultra‐large specific surface area has been prepared using hollow silica mesoporous spheres (HMSSs) as building block in this work. These building blocks were made weakly hydrophobic in order to produce HMSS particle stabilized foams. The foams exhibit a uniform primary macropore structure, which is composed of a three dimensional HMSS‐assembled network, via HMSS‐stabilized foams. The influence of sintering temperature on the microstructure and properties of HMSS foams is investigated. The HMSS foams exhibit highest specific surface area of 1733 m2/g, attributed to the radial mesopores in HMSS shell, when sintered at between 500°C and 800°C. This specific surface area is much higher than that of existing ceramic materials. The uniform pore structure and ultra‐large specific surface area make it a promising lightweight material in potential application fields, including catalyst, adsorption, fire‐resistant thermal insulation, and load and control release system. Hollow mesoporous silica spheres assembled foam material with uniform macro‐pore structure and ultra‐high specific surface area, prepared from HMSSs stabilized colloidal foams [ABSTRACT FROM AUTHOR]

Abstract A facile method for preparation of SiC nanofibrous network reinforced hierarchical structured porous Si 3 N 4 based ceramics via annealing Si-Si 3 N 4 binary particle-stabilized foam in coke bed is reported in this work for the first time. The atmosphere created by coke bed enables the fabrication of Si 3 N 4 based porous ceramics at 1450 °C without using sintering additives. As prepared specimens possess a relative high compressive strength due to the partial oxidation of Si 3 N 4 particles. This novel structure with three levels of hierarchy characterized by flexible SiC nanofibrous network, cell walls and unit cells can be characterized. The vaporization of silicon powder results in formation of Si(g), SiO(g) and allows subsequent generation of SiC nanofibrous network, leading to a considerable number of micro-pores on cell walls simultaneously. As-prepared porous ceramics contained 76.7% porosity and had compressive strength of 10.81 MPa. [ABSTRACT FROM AUTHOR]

Abstract We reveal that zeta potential has a notable effect on properties of foamed suspension, which remains poorly explored. It is demonstrated low zeta potential is beneficial for foam stability, and the experimental results show that absolute value of zeta potential of 30–40 mV is the boundary between stable foams and unstable foams. High zeta potential above 40 mV gives rise to instability of foamed colloidal suspension, owing to strong interparticle repulsion force that prevents particles from forming a closely packed particle network at liquid/air interfaces. Besides, it is found that high zeta potential leads to low foamability of foamed colloidal suspension. It is also demonstrated herein that stable and uniform foams with thin and homogeneous-thickness wall without agglomerates can be prepared at the isoelectric point (IEP) using long-chain surfactant, which generates weak agglomerated particles that can be re-separated to monodisperse particles due to the steric hindrance effect of surfactant. [ABSTRACT FROM AUTHOR]

In order to reduce thermal conductivity but to exhibit better mechanical properties of porous alumina ceramics (PACs), a novel approach, based on the modification of pore structures (i.e. mean pore size, micro-pore proportions and pore shape factor) by impregnation of alumina sol, is reported in the present work. The properties of as-impregnated samples were compared with commercial alumina hollowsphere bricks. Results show that impregnation of alumina sol in PACs has a positive influence on pore structures, leading to a superior strength and a lower thermal conductivity. In particular, when 8 wt% alumina sol solid content is impregnated, the crushing strength (35.3 MPa) and thermal conductivity (0.15 W/m K at 200 °C) of sample are much better than that of the commercial alumina hollowsphere bricks. This novel method for excellent PACs provides promising applications as insulating lining materials in the fields of industrial furnace. [ABSTRACT FROM AUTHOR]

The generation of PVA hydrogel through freeze-thaw technique has been utilized innovatively to complete the forming process of porous Si 3 N 4 ceramics in the present work. In comparison with gelcasting method, green body with comparable strength has been achieved by this novel forming process, which is owing to the strong function of PVA gel caused by the freeze-thaw cycles. Herein, Si 3 N 4 hollow spheres are employed as pore-forming agent in order to achieve closed pores. The morphology of green body illustrates that pores originate from both hollow spheres and the space occupied by ice crystals, and the latter gives rise to the increase of porosity around 10%. Studies on the mechanical, dielectric and thermal properties of porous Si 3 N 4 ceramics dependent on freeze-thaw cycle and freezing time have been performed. It is found that porous ceramics treated for freeze-thaw 2 cycles with freezing time of 24 h present excellent properties, which are promising to be applied as radome materials. [ABSTRACT FROM AUTHOR]

A novel temperature induced gelation method for alumina suspension using oleic acid as dispersant is reported. Non–aqueous suspension with high solid loading and low viscosity is prepared using normal octane as solvent. Influence of oleic acid on the dispersion of suspension was investigated. There was a well disperse alumina suspension with 1.3 wt% oleic acid. Influence of gelation temperature on the coagulation process and properties of green body was investigated. The sufficiently high viscosity to coagulate the suspension was achieved at −20 °C. The gelation temperature was controlled between the melting point of dispersant and solvent. The gelation mechanism is proposed that alumina suspension is destabilized by dispersant separating out from the solvent and removing from the alumina particles surface. The alumina green body with wet compressive strength of 1.07 MPa can be demolded without deformation by treating 53 vol% alumina suspension at −20 °C for 12 h. After being sintered at 1550 °C for 3 h, dense alumina ceramics with relative density of 98.62% and flexural strength of 371±25 MPa have been obtained by this method. [ABSTRACT FROM AUTHOR]