Search

Flexible membrane with good anti‐wettability under giant deformation and fast healing will largely extend its adaptability and life span in anti‐/deicing application. A flexible membrane with significant dynamic water repellency and photo‐/electro‐responsive healing capability is reported, fabricated by combining the covalent grafting of fluorosilane to carbon black (F‐CB) with the optimized ablation difference between thermoplastic polyurethane (TPU) matrix and F‐CB. A rolling angle of below 5° is remained after either being stretching to 1000% strain or 2000 cycles of tensile tests at 400% strain. More importantly, multi‐scale cracks on the membrane can be diagnosed and repaired in real‐time; the healing efficiency reaches above 99% within 90 s even if completely fractured under the effect of both solar irradiation of 0.1 W cm−2 and applied voltage of 20 V; and all‐weather anti‐/deicing has the performance of an icing delay time of 323 s and an ice adhesion strength of <40 kPa, a sharp contrast to the 18 s and 1090 kPa, respectively, for bare metal surface. This work endows anti‐icing membrane with the ability of damage detection and cyclic healing, highly demanded in outdoor anti‐/deicing application that involve inevitable mechanical damages. [ABSTRACT FROM AUTHOR]

It is an increasingly mature application solution that triboelectric nanogenerator (TENG) supplies power to electronic devices through its power management system (PMS). However, the previous PMS is able to manage a limited voltage magnitude and the energy storage elements are limited to capacitors. This work proposes an ultrahigh voltage PMS (UV‐PMS) to realize the charging of commercial lithium cells (LCs) by TENG. The design of UV‐PMS enables energy management of TENGs with ultrahigh open‐circuit voltages up to 3500 V and boosts the peak charging current from 30.9 µA to 2.77 mA, an increase of 89.64 times. With the introduction of UV‐PMS, the effective charging capacity of LC charged by a TENG at a working frequency of 1.5 Hz for 1 h comes to 429.7 µAh, making a 75.3 times enhancement compared to charging by TENG directly. The maximum charging power comes to 1.56 mW. The energy storage efficiency is above 97% and the overall charge efficiency can be maintained at 81.2%. This work provides a reliable strategy for TENG to store energy in LC, and has promising applications in energy storage, LC's life, and self‐powered systems. [ABSTRACT FROM AUTHOR]

The metal–insulator transition (MIT) of vanadium dioxide (VO2), which involves significant changes in electrical, optical, and other properties, has attracted widespread attention. Here, we report a triboelectric nanogenerator (TENG)-based self-powered VO2 phase transition. With the TENG-induced ionic gel gating, the hydrogen ion insertion/detachment in the VO2 lattice can be modulated at room temperature to cause phase transitions that control light transmittance. The phase transition behavior is characterized by X-ray diffraction and Raman spectroscopy. Under the continuous power supply from TENG, the X-ray diffraction peak of VO2 shifts, and the Raman intensities of characteristic peaks decrease, accompanied by a color change from brown to translucent. The electrical conductivity undergoes a significant change by two orders of magnitude and persists overnight, indicating an excellent duration of the phase transition. In addition, a raindrop TENG-induced VO2 phase transition is demonstrated. The infrared transmittance of VO2 is decreased dramatically by 28.1% due to the phase transition, achieving a heat preservation effect that holds promise for adaptive thermal insulation in smart windows during rainfall through raindrop power generation. This work has realized the TENG-based self-powered VO2 phase transition, holding significant application potential in smart homes. [ABSTRACT FROM AUTHOR]

Substrate-free electrodes are promising dry electrodes for long-term physiological electrical signal monitoring due to their ultra-thinness, conformal contact, and stable skin–electrode impedance. However, the response of substrate-free electrodes to various disturbances during electrocardiogram (ECG) monitoring and the corresponding optimization needs to be investigated. This paper investigates the specific effects of various influencing factors on skin–electrode impedance and ECG during electrocardiogram (ECG) detection. The research utilizes substrate-free poly(3,4-ethylenedioxythiophene)/poly(styrene-sulfonate) (PEDOT:PSS) electrodes. The investigation employs several methods, including skin–electrode impedance comparison, ECG waveform analysis, spectrum analysis, and signal-to-noise ratio (SNR) evaluation. To avoid the impact of physiological state differences in subjects at different times, relevant data were only compared with the same group of experiments conducted in the same period. The results demonstrate that the substrate-free conformal contact PEDOT:PSS electrode has more stable skin–electrode impedance and could obtain a more stable ECG than partial contact electrodes (the SNR of the partial contact and conformal contact electrodes are 1.2768 ± 4.0299 dB and 7.2637 ± 1.4897 dB, respectively). Furthermore, the ECG signal quality of the substrate-free conformal contact PEDOT:PSS electrode was independent of the electrode area and shape (the SNRs of the large, medium, and small electrodes are 4.0447 ± 0.4616 dB, 3.9115 ± 0.5885 dB, and 4.1556 ± 0.5557 dB, respectively; the SNRs of the circular, square, and triangular electrodes are 9.2649 ± 0.6326 dB, 9.2471 ± 0.6806 dB, and 9.1514 ± 0.6875 dB, respectively), showing high signal acquisition capability that is the same as microneedle electrodes and better than fabric electrodes. The results of clothing friction effects show that skin–electrode impedance stability was important for ECG stability, while the impedance value was not (the SNRs of friction and non-friction electrodes are 2.4128 ± 7.0784 dB and 9.2164 ± 0.6696 dB, respectively). Moreover, the skin–electrode impedance maintains stability even at a high breathing frequency, but the ECG signal fluctuates at a high breathing frequency. This experiment demonstrates that even when the skin–electrode impedance remains stable, the ECG signal can still be susceptible to interference from other factors. This study suggests that substrate-free PEDOT:PSS that could form conformal contact with the skin has higher skin–electrode impedance stability and could measure a high ECG signal even with a small electrode area, demonstrating its potential as dry ECG electrodes, but the interference from other physiological electrical signals may require better circuit design. [ABSTRACT FROM AUTHOR]

With the advancement of internet of things and wireless sensing technology, the need for personnel track and position monitoring are greatly increasing. Commercial global positioning system (GPS) and Global system for mobile communications (GSM) position methods cannot meet the demand for low power consumption and three‐dimensional indoor position monitoring. Herein, a self‐powered position monitoring system (SPMS) based on an insole‐type wearable triboelectric nanogenerator (IW‐TENG) and Bluetooth beacon for human kinetic energy harvesting and sustainable position monitoring is proposed. The SPMS consists of an insole‐type wearable triboelectric nanogenerator, an energy management module (EMM), and a Bluetooth low energy (BLE) beacon module. Benefitting from the multilayers structure, a maximum energy of 120 µJ per step can be harvested by the IW‐TENG with EMM for a typical adult. By every 3–4 steps, SPMS can transmit Bluetooth signals to obtain the location information. A single BLE signal transmission consumes only 136 µJ, and the transmission distance can reach 100 m. The SPMS is applied to intelligent attendance in office rooms and shows great prospects in intelligent navigation and trajectory tracking in local area network. [ABSTRACT FROM AUTHOR]

The unique attribute of transient technology is that it promotes the potential for the design and implementation of sustainable systems through their capability to fully or partially disintegrate after a predefined period of stable operation. Transient electronics have a wide range of potential applications as biomedical implants, environmental sensors, and hardware‐secured devices. Controlled disintegration of such systems without the need for harsh solvents is a step toward realizing green and sustainable electronics. In this short review, recent progress in the development of transient electronics is studied. First, an overview of the transient materials, both the substrate and electronic component, is described. Second, the mechanisms under which transiency occurs, including aqueous dissolution and thermal degradation, are reported. Third, manufacturing techniques for the fabrication of transient electronics are reviewed. And last, various transient electronic devices and their applications are discussed. [ABSTRACT FROM AUTHOR]

ABSTRACT Transient electronics is a class of electronic devices designed to maintain stable operation for a desired and preset amount of time; and, undergo fast and complete degradation and deconstruction once transiency is triggered. Controlled and programmed transiency in solvent-triggered devices is strongly dependent on chemical and physical interactions between the solvent and the device, as well as those within the device itself, among its constituent components. Mechanics of transiency of prototypical transient circuits demonstrate strong dependence of the transiency characteristics on that of the substrate. In the present study, we demonstrate the control of transiency through the dissolution behavior of a substrate for the devices with electronic parts composed of colloidal units. It is observed that the physical circuit-substrate interactions are the dominating factors in defining the overall transiency behavior of the device. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 517-524 [ABSTRACT FROM AUTHOR]

Thermoplastic resins (linear low-density polyethylene (LLDPE), high-density polyethylene (HDPE), and polypropylene (PP)) reinforced by different content ratios of raw agave fibers were prepared and characterized in terms of their mechanical, thermal, and chemical properties as well as their morphology. The morphological properties of agave fibers and films were characterized by scanning electron microscopy and the variations in chemical interactions between the filler and matrix materials were studied using Fourier-transform infrared spectroscopy. No significant chemical interaction between the filler and matrix was observed. Melting point and crystallinity of the composites were evaluated for the effect of agave fiber on thermal properties of the composites, and modulus and yield strength parameters were inspected for mechanical analysis. While addition of natural fillers did not affect the overall thermal properties of the composite materials, elastic modulus and yielding stress exhibited direct correlation to the filler content and increased as the fiber content was increased. The highest elastic moduli were achieved with 20 wt % agave fiber for all the three composites. The values were increased by 319.3%, 69.2%, and 57.2%, for LLDPE, HDPE, and PP, respectively. The optimum yield stresses were achieved with 20 wt % fiber for LLDPE increasing by 84.2% and with 30 wt % for both HDPE and PP, increasing by 52% and 12.3% respectively. [ABSTRACT FROM AUTHOR]