Search

The influence of tubificid worms on nutrient translocation from water to fish farm sediments accumulating in settling ponds was addressed under laboratory conditions. Small microcosms of 0.5 L were filled up with 35 g of sludge from a fish farm settling pond and 0.15 L of filtered settling pond water. The experimental set up consisted of one control line (no worms added), a second experimental line with 1 mg of tubificid worms·g-1 fresh sediment (550 individuals·m-2) and a third experimental line with 40 mg of tubificid worms·g-1 fresh sediment (22 000 individuals·m-2). Nutrients translocation was determined by monitoring overlaying water concentration of ammonia, nitrate and phosphate for ten days. Results showed that abundances of 550 individuals·m-2 had no significant influence on the fluxes of nutrients here considered. However, the influence of higher abundances of tubificids (22 000 individuals·m-2) was of significant extent on the translocation of nitrate and phosphate. Accordingly, bioturbation of tubificids caused 55% lower nitrate uptake by the sediment when compared to control conditions. Phosphorus released by the sediments of the control condition was ca. 90% higher than that recorded under abundances of tubificids (22 000 individuals·m-2). Results obtained allowed us to estimate that fish farm settling ponds highly colonized by tubificid worms (22 000 individuals·m-2) may contribute to decrease phosphorus discharge (in terms of soluble phosphorus) in ca. 5 g of P·ton-1 of fish produced.

Abstract: Raw biogas, produced by anaerobic digestion of organic matter, is a methane-rich combustible gas. The CH4 content can be upgraded to reach the natural gas composition for vehicle fuel use (bio-CNG) or injection into the gas grid. This upgrading is performed by CO2 removal and pollutants treatment (H2S, water, etc.). The accelerated carbonation on BOF slag, a by-product from the steel industry containing calcium and iron oxides, was studied as a solution. The purpose of this work was to study the potential of slags to remove simultaneously CO2 with CaO (carbonation) and H2S with Fe2O3 (sulfuration) under atmospheric conditions. Firstly, batch experiments have confirmed the reactivity among CO2, H2S and slag. Removal capacities of 63 and 140 were estimated. The effect of the amount of water in the mix biogas/slag was studied on treatment performances, and an optimal L/S range between 0.05 and 0.2 Lwater/kgBOF was found. Secondly a field scale column experiment has been performed to treat the biogas of a pilot digester. This test under dynamic conditions using a BOF slags filter has given promising results (73 ). [ABSTRACT FROM AUTHOR]

Increasing energy demands combined with local scarcities and rising prices make the valorisation of energy from domestic wastewater seen as a valuable resource. Chemically enhanced primary treatment (CEPT) enables an increased redirection of organic compounds into sludge in the primary stage of a wastewater treatment for a transformation into biogas (carbon capture). Traditionally used coagulants consist of metallic salts, but in the last two decades, the development of polymers, based on petroleum or synthesized from renewable sources such as plants, has been intensified. However, a direct comparison of the effectiveness of these products is missing. In this paper, we analysed data of peer-reviewed research from jar tests to full-scale studies, highlighting key parameters for successful carbon capture. More than 100 studies were identified, with a majority presenting results from tests under static conditions (jar tests), while data on full-scale applications are scarce. Overall, for TSS and COD, a clear correlation between inflow concentration and removal efficiency was found, irrespective of the product used. Comparison between the effectiveness of the different types of products is difficult, but bio-based coagulants need to be generally added in higher product concentrations for a considerable removal efficiency. While CEPT seems to increase the general sludge and biogas output, future studies should focus on harmonising laboratory analysis to make results comparable. Another important issue that should be addressed is the provision of experimental details, especially for full-scale trials, to enable for reliable conclusions., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Florent Chazarenc reports financial support was provided by Rhone Mediterranee Corsica Region Water Agency. Katharina Tondera reports a relationship with EUR H2O'Lyon that includes: funding grants., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The use of treatment wetlands (TWs) presents particular challenges in regions with sub-zero winter temperatures, due to reduced biological activity and risk of pipe breakage or clogging due to freezing. We studied the vertical temperature distribution in four pilot-scale TWs exposed to winter temperatures in order to determine the impact of operational system parameters and the role of insulation on heat conservation inside the filtering bed. The overall temperature pattern was similar in all wetlands, with a trend of increasing temperature from the surface toward the bottom during the cold season. No freezing was detected in the wetlands despite average daily temperatures as low as -20 °C. Influent water temperature and hydraulic loading had a stronger influence on TW temperatures in winter than air temperature. The vertical distribution of temperatures in TWs is more sensitive to hydraulic loading variation in the percolating operating condition than in the saturated flow with forced aeration configuration. Our results suggest that TW systems can remain operational under cold winter conditions provided the surface is properly insulated by vegetation, mulch and/or snow.

The application of photocatalysis for the disinfection of water has been extensively reported over the past 30 years. Titanium dioxide (TiO 2 ) has been the most widely and successfully used photocatalyst to date; however, it is not without its limitations. Frequently observed long lag times, sometimes up to 60 min, before bacterial inactivation begins and the presence of residual microorganisms, for example, up to 10 4 colony forming units, remaining after treatment are ongoing challenges with this particular photocatalyst. It is therefore important to find alternative photocatalysts that can address these issues. In this study, we compared the disinfection capacity of TiO 2 with that of zinc oxide (ZnO) using Escherichia coli as a model organism in both a suspended and immobilized catalyst system. Our results showed that ZnO was superior to TiO 2 in a number of areas. Not only were bacterial rates of destruction much quicker with ZnO, but no lag time was observed prior to inactivation in suspended systems. Furthermore, complete bacterial destruction was observed within the treatment times under investigation. The greater efficiency of ZnO is believed to be due to the decomposition of the bacterial cell wall being driven by hydrogen peroxide as opposed to hydroxyl radicals. The results reported in this paper show that ZnO is a more efficient and cost-effective photocatalyst than TiO 2 and that it represents a viable alternative photocatalyst for water disinfection processes., Competing Interests: The authors declare no competing financial interest., (© 2023 The Authors. Published by American Chemical Society.)

Root fungal endophytes have been shown to play a positive role in soil phytoremediation by immobilizing or degrading contaminants. In comparison, little is known about their ecological functions and possible role in improving plant performance in treatment wetlands. In a greenhouse study, we compared the structure of fungal communities associated with Phragmites australis roots in treatment wetland mesocosms fed with pre-treated wastewater to mesocosms fed with drinking water. We evaluated the role of water source as an environmental filter structuring fungal communities, and correlated the relative abundances of fungal taxa with key services delivered by the wetlands (i.e., biomass production and nutrient removal). Mesocosms fed with wastewater had higher fungal alpha-diversity. Contrary to expectations, many fungi were unique to drinking water-fed mesocosms, suggesting that the oligotrophic conditions prevailing in these mesocosms benefited specific fungal taxa. On the other hand, wastewater-fed mesocosms had a slightly higher proportion of sequence reads belonging to fungal species recognized as potential endophytes and phytopathogens, highlighting the potential role of wastewater as a source of plant-associated fungi. Interestingly, we found contrasted association patterns between fungal species' relative abundances and different treatment wetland services (e.g., N vs P removal), such that some fungi were positively associated with N removal but negatively associated with P removal. This suggests that fungal endophytes may be functionally complementary in their contribution to distinct mesocosm services, thus supporting arguments in favor of microbial diversity in phytotechnologies. Because of the wide alpha-diversity of fungal communities, and the fact that with current databases, most species remained unassigned to a specific function (or even guild), further investigation is needed to link fungal community structure and service delivery in treatment wetlands., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

In response to the growing global resource scarcity, wastewater is increasingly seen as a valuable resource to recover and valorise for the benefit of the society rather than another waste that needs treatment before disposal. Conventional wastewater treatment plants (WWTPs) oxidise most of the organic matter present in wastewater, instead of recovering it as a feedstock for biomaterials or to produce energy in the form of biogas. In contrast, an A-Stage is capable of producing a concentrated stream of organic matter ready for valorisation, ideally suited to retrofit existing large plants. This technology is based on the principle of high-rate activated sludge process that favours biosorption and storage over oxidation. In this paper, we summarize peer-reviewed research of both pilot-scale and full-scale studies of A-Stage process under real conditions, highlighting key operational parameters. In the majority of published studies, the sludge retention time (SRT) was identified as a key operational parameter. An optimal SRT of 0.3 days seems to maximize the redirection of influent COD - up to 50% to the sludge flux, while simultaneously keeping mineralization under 25% of total influent COD. Other key optimal parameters are a hydraulic residence time of 30 min and dissolved oxygen levels of 0.5 mg⋅L - 1 . In addition, nutrient removal efficiencies of 15-27% for total nitrogen and 13-38% for total phosphorus are observed. Influence of mixing on settling efficiencies remain largely underexplored, as well as impact of wet weather flow and temperature on overall recovery efficiencies, which hinders to provide recommendations on these aspects. Evolution of modelling efforts of A-Stage process are also critically reviewed. The role of extracellular polymeric substances remain unclear and measures differ greatly according to the different studies and protocols. Better understanding the settling processes by adding Limit of Stokesian and Threshold of Flocculation measures to Sludge Volume Index could help to reach a better understanding of the A-Stage process. Reliable modelling can help new unit processes find their place in the whole treatment chain and help the transition from WWTPs towards Wastewater Resource Recovery Facilities., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022. Published by Elsevier Ltd.)

The scope of this study was to investigate if using zeolite as a reactive material in a vertical-flow wetland under field conditions improves ammonium removal from domestic wastewater in the long term. The experimental setup consisted of two pilot-scale first stage French vertical flow treatment wetlands (2.3 m 2 surface area each), which were implemented under field scale conditions inside a wastewater treatment plant in the central region of France (L'Encloitre, 37360). The filters were operated during 27 months. A compact pilot containing Leca ® as a main filtration layer (Ø 1-5 mm) was compared to a similar one filled with natural zeolite (Ø 2-5 mm). The pilots were fed according to regular feeding/resting periods (3½/7 days) and the nominal loading rate was of 300 g COD m -2 d -1 and 33 g·N·m -2 ·d -1 during operation. In both pilots, results showed a removal efficiency of more than 90 and 85% for TSS and COD, respectively. They also showed an increased NH 4 -N removal of 9% on average (total removal efficiency of 84%) with the use of zeolite compared to Leca ® . The ion exchange capacity of zeolite seemed not to be affected after 27 months of experiments; however, the material was compacted and more friable after operation.

Bioaugmentation in the form of artificial mycorrhization of plant roots and bacterial inoculation has been successfully implemented in several fields including soil remediation or activated sludge treatment. Likewise, bioaugmentation seems a promising approach to improve the functioning of treatment wetlands, considering that natural mycorrhization has been detected in treatment wetlands and that bacteria are the main driver of contaminant degradation processes. However, to date, full scale implementation seems to be rare. This review synthesizes the effects of bioaugmentation on different types of treatment wetlands, to a large extent performed on a microcosm (<0.5 m 2 ) or mesocosm scale (0.51 to 5 m 2 ). While inoculation with arbuscular mycorrhizal fungi tended to show a positive effect on the growth of some wetland plants (e.g. Phragmites australis), the mechanisms underlying such positive effects are not well understood and the effects of upscaling to full scale treatment wetlands remain unknown. Bacterial inoculation tended to promote plant growth and pollutant degradation, but longer term data is required., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Plant species selection is an important criterion for improving treatment wetland performance. The aim of this work was to evaluate removal efficiency and potential uses of woody species in treatment wetlands during the establishment year. Plant development, removal efficiency and evapotranspiration rate of five woody species ( Salix interior, Salix miyabeana, Sambucus canadensis, Myrica gale, Acer saccharinum ) and four herbaceous taxa typically used in treatment wetlands ( Typha angustifolia, Phragmites australis australis, Phragmites australis americanus, Phalaris arundinacea ) were compared in a mesocosm-scale study during one growing season. Woody species showed significantly slower growth, but displayed several characteristics of interest for treatment wetland applications: good adaptation to wetlands conditions; high organic matter removal (76-88%); high nutrient accumulation in tissues and high evapotranspiration capacity. During the establishment year, herbaceous species showed greater biomass development (above- and belowground parts), higher evapotranspiration rate (>3.84 L m -2  d -1 compared to <3.23 L m -2  d -1 for woody species) and overall pollutant removal efficiency. These characteristics confirm the high efficiency of treatment wetlands planted with herbaceous species even in the first growing season. However, given their greater potential biomass development, woody species could represent an excellent alternative for improving treatment wetlands long-term performance.

The objective of this study was to determine how macrophytes commonly used in treatment wetlands (TWs) respond to water with low pollutant concentration. We measured pollutant removal efficiency and compared growth and nutrient uptake of five macrophytes in demonstration scale units (volume >40 m 3 ) irrigated by water with pollutant concentrations representative of average urban stormwater quality. All species showed a strong productivity gradient along the beds, starting with high biomass - high density near the inlet, then decreasing progressively with distance. Cyperus was by far the most productive species. Phragmites and Thalia had higher biomass in the first few metres of the beds than Typha and Arundo. In terms of pollutant removal, decreasing plant growth may be interpreted as indicative of high efficiency when caused by nutrient depletion. Differences in aboveground biomass between species did not translate into measurable differences in removal efficiency at the outlet. Although Phragmites australis is the species most commonly used in TWs, under the low nutrient load, Cyperus had twice its biomass, and higher N and P uptake. These results highlight the importance of considering wastewater characteristics when selecting macrophyte species for TWs.

Steel slag filters, if well designed and operated, may upgrade phosphorus removal in small wastewater treatment plants such as stabilization ponds and constructed wetlands. The main objective of this study was to develop a systemic modelling approach to describe changes in the hydraulic performances and internal hydrodynamics of steel slag filters under real dynamic operating conditions. The experimental retention time distribution curves (RTD curves) determined from tracer experiments performed at different times during the first year of operation of two field-scale steel slag filters were analyzed through a three stage process. First, a statistical analysis of the RTD curves was performed to determine statistical parameters of the retention time distribution. Second, classical tanks in series (TIS) and plug flow with dispersion (PFD) models were used to obtain a first evaluation of the dispersion and mixing regime. Finally, a multi-flow path TIS model, based on the assumption of several flow paths with different hydraulic properties, is proposed to accurately describe the internal hydrodynamics. Overall, the results of this study indicate that higher CaO content, round shape, and larger grain size distribution of steel slag may promote plug-like flow rather than dispersion. The results of the multi-flow path TIS model suggest that the internal hydrodynamics of steel slag filters can be primarily described by two main flow paths: (i) a faster main flow path showing higher plug flow, followed by (ii) a slower secondary flow path showing higher dispersion. The results also showed that internal hydrodynamics may change over time as a consequence of physical-chemical phenomena occurring in the filter, including accumulation of precipitates, slag hydration and carbonation, and particle segregation., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

This simulation study investigates the treatment performance of a compact French vertical flow wetland using a zeolite layer in order to increase ammonium nitrogen removal. For the modelling exercise, the biokinetic model CW2D of the HYDRUS Wetland Module is used. The calibrated model is able to predict the effect of different depths of the zeolite layer on ammonium nitrogen removal in order to optimize the design of the system. For the model calibration, the hydraulic effluent flow rates as well as influent and effluent concentrations of chemical oxygen demand (COD) and NH 4 -N have been measured. To model the adsorption capacity of zeolite, Freundlich isotherms have been used. The results present the simulated treatment performance with three different depths of the zeolite layer, 10 cm (default), 15 cm and 20 cm, respectively. The increase of the zeolite layer leads to a significant decrease of the simulated NH 4 -N effluent concentration.

Electric arc furnace steel slag (EAF-slag) and basic oxygen furnace steel slag (BOF-slag) were used as filter substrates in two horizontal subsurface flow filters (6 m(3) each) designed to remove phosphorus (P) from the effluent of a constructed wetland. The influences of slag composition, void hydraulic retention time (HRTv), temperature, and wastewater quality on treatment performances were studied. Over a period of almost two years of operation, the filter filled with EAF-slag removed 37% of the inlet total P, whereas the filter filled with BOF-slag removed 62% of the inlet total P. P removal occurred predominantly via CaO-slag dissolution followed by Ca phosphate precipitation. P removal efficiencies improved with increasing temperature and HRTv, most probably because this affected the rates of CaO-slag dissolution and Ca phosphate precipitation. It was observed that long HRTv (>3 days) can cause high pH in the effluents (>9) as a result of excessive CaO-slag dissolution. However, at shorter HRTv (1-2 days), pH values were elevated only during the first five weeks and then stabilized below a pH of 9. The kinetics of P removal were investigated employing a first-order equation, and a model for filter design was proposed.

Sludge treatment wetlands are mainly used to reduce the volume of activated sludge, and the pollutants at the outlet are generally returned to the wastewater treatment plant. However, in cases where sludges are produced far from treatment plants not only must the sludge be treated, but the discharge of pollutants into the surrounding environment must also be limited. The aim of this study was to evaluate the efficiency of different plant species in optimising pollutant removal in a decentralised sludge treatment wetland. In addition, a new system design was assessed, in which the wetland was not completely drained, and a saturated layer was created using an overflow. The experimental setup consisted of 16 mesocosms in total, planted with monocultures of Phragmites australis, Typha angustifolia and Scirpus fluviatilis, and unplanted controls, each in four replicates. The experiment was conducted during the third summer of operation after setup. The system was fed with highly concentrated fish farm sludge at a load of 30 kg of total solids m(-2) yr(-1). Results showed that such wetlands were highly efficient, with removal rates between 94% and 99% for most pollutants. Planted systems generally outperformed the unplanted control, with a significantly lower mass of pollutants at the outlet of the sludge treatment wetland planted with Phragmites, followed by those with Typha and then Scirpus. The distinct influence of plant species on pollution removal was explained by the sequestration of nitrogen and phosphorus in plant tissues and by the rhizosphere effect, which enhance the biodegradation of organic matter, allowed the nitrification process and created redox conditions favourable to the sorption of phosphorus. Filtration and evapotranspiration rates played a major role in limiting the discharge of pollutants, and the impact was enhanced by the fact that the sludge treatment wetland was not completely drained., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Electric arc furnace steel slags (EAF-slags) and basic oxygen furnace steel slags (BOF-slags) were used to remove phosphate from synthetic solutions and real wastewater. The main objective of this study was to establish an overview of the phosphate removal capacities of steel slags produced in Europe. The influences of parameters, including pH, and initial phosphate and calcium concentrations, on phosphate removal were studied in a series of batch experiments. Phosphate removal mechanisms were also investigated via an in-depth study. The maximum capacities of phosphate removal from synthetic solutions ranged from 0.13 to 0.28 mg P/g using EAF-slags and from 1.14 to 2.49 mg P/g using BOF-slags. Phosphate removal occurred predominantly via the precipitation of Ca-phosphate complexes (most probably hydroxyapatite) according to two consecutive reactive phases: first, dissolution of CaO-slag produced an increase in Ca(2+) and OH(-) ion concentrations; then the Ca(2+) and OH(-) ions reacted with the phosphates to form hydroxyapatite. It was found that the release of Ca(2+) from slag was not always enough to enable hydroxyapatite precipitation. However, our results indicated that the Ca(2+) content of wastewater represented a further source of Ca(2+) ions that were available for hydroxyapatite precipitation, thus leading to an increase in phosphate removal efficiencies., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Greenhouse gas (GHG) emissions by constructed wetlands (CWs) could mitigate the environmental benefits of nutrient removal in these man-made ecosystems. We studied the effect of 3 different macrophyte species and artificial aeration on the rates of nitrous oxide (N(2)O), carbon dioxide (CO(2)) and methane (CH(4)) production in CW mesocosms over three seasons. CW emitted 2-10 times more GHG than natural wetlands. Overall, CH(4) was the most important GHG emitted in unplanted treatments. Oxygen availability through artificial aeration reduced CH(4) fluxes. Plant presence also decreased CH(4) fluxes but favoured CO(2) production. Nitrous oxide had a minor contribution to global warming potential (GWP<15%). The introduction of oxygen through artificial aeration combined with plant presence, particularly Typha angustifolia, had the overall best performance among the treatments tested in this study, including lowest GWP, greatest nutrient removal, and best hydraulic properties.

Nitrogen (N) processing in constructed wetlands (CWs) is often variable, and the contribution to N loss and retention by various pathways (nitrification/denitrification, plant uptake and sediment storage) remains unclear. We studied the seasonal variation of the effects of artificial aeration and three different macrophyte species (Phragmites australis, Typha angustifolia and Phalaris arundinacea) on N processing (removal rates, transformations and export) using experimental CW mesocosms. Removal of total nitrogen (TN) was higher in summer and in planted and aerated units, with the highest mean removal in units planted with T. angustifolia. Export of ammonium (NH(4)(+)), a proxy for nitrification limitation, was higher in winter, and in unplanted and non-aerated units. Planted and aerated units had the highest export of oxidized nitrogen (NO(y)), a proxy for reduced denitrification. Redox potential, evapotranspiration (ETP) rates and hydraulic retention times (HRT) were all predictors of TN, NH(4)(+) and NO(y) export, and significantly affected by plants. Denitrification was the main N sink in most treatments accounting for 47-62% of TN removal, while sediment storage was dominant in unplanted non-aerated units and units planted with P. arundinacea. Plant uptake accounted for less than 20% of the removal. Uncertainties about the long-term fate of the N stored in sediments suggest that the fraction attributed to denitrification losses could be underestimated in this study.

Natural apatite has emerged as potentially effective for phosphorus (P) removal from wastewater. The retention capacity of apatite is attributed to a lower activation energy barrier required to form hydroxyapatite (HAP) by crystallization. The aim of our study was to test the P removal potential of four apatites found in North America. Minerals were collected from two geologically different formations: sedimentary apatites from Florida and igneous apatites from Quebec. A granular size ranging from 2.5 to 10mm to prevent clogging in wastewater applications was used. Isotherms (24 and 96 h) were drawn after batch tests using the Langmuir model which indicated that sedimentary apatites presented a higher P-affinity (K(L)=0.009 L/g) than igneous apatites (K(L) approximately 0.004 L/g). The higher density of igneous material probably explained this difference. P-retention capacities were determined to be around 0.3mg P/g apatite (24 h). A 30 mg P/L synthetic effluent was fed during 39 days to four lab-scale columns. A mixture of sedimentary material (apatite and limestone 50-50%, w/w) showed a complete P-retention during 15 days which then declined to 65% until the end of the 39 days lab scale test period. A limitation in calcium may have limited nucleation processes. The same mixture used in a field scale test showed 60% P-retention from a secondary effluent (30 mg COD/L, 10 mg Pt/L) during 65 days without clogging.