Search

Intercalation of non-van der Waals (vdW) layered materials can produce new 2D and 3D materials with unique properties, but it is difficult to achieve. Here, we describe a structural editing protocol for 3D non-vdW layered ternary carbides and nitrides (MAX phases) and their 2D vdW derivatives (MXenes). Gap-opening and species-intercalating stages were mediated by chemical scissors and guest intercalants, creating a large family of layered materials with unconventional elements and structures in MAX phases, as well as MXenes with versatile termination species. Removal of surface terminations by metal scissors and stitching of carbide layers by metal atoms leads to a reverse transformation from MXenes to MAX phases, and metal-intercalated 2D carbides. This scissor-mediated structural editing may enable structural and chemical tailoring of other layered ceramics.

Thermal expansion of MAX phases along different directions tended to be different because of the anisotropy of hexagonal crystals. Herein, a new Hf2SeC phase was synthesized and confirmed to be relatively isotropic, whose coefficients of thermal expansion (CTEs) were determined to be 9.73 {\mu}K-1 and 10.18 {\mu}K-1 along a and c directions. The strong M-S bond endowed Hf2SC and Zr2SC lower CTEs than Hf2SeC and Zr2SeC. A good relationship between the thermal expansion anisotropy and the ratio of elastic stiffness constant c11 and c33 was established. This straightforward approximation could be used to roughly predict the thermal expansion anisotropy of MAX phases.

Two dimensional (2D) ferromagnetic materials have attracted much attention in the fields of condensed matter physics and materials science, but their synthesis is still a challenge given their limitations on structural stability and susceptibility to oxidization. MAX phases nanolaminated ternary carbides or nitrides possess a unique crystal structure in which single-atom-thick A sublayers are interleaved by two dimensional MX slabs, providing nanostructured templates for designing 2D ferromagnetic materials if the non-magnetic A sublayers can be substituted replaced by magnetic elements. Here, we report three new ternary magnetic MAX phases (Ta2FeC, Ti2FeN and Nb2FeC) with A sublayers of single-atom-thick 2D iron through an isomorphous replacement reaction of MAX precursors (Ta2AlC, Ti2AlN and Nb2AlC) with a Lewis acid salts (FeCl2). All these MAX phases exhibit ferromagnetic (FM) behavior. The Curie temperature (Tc) of Ta2FeC and Nb2FeC MAX phase are 281 K and 291 K, respectively, i.e. close to room temperature. The saturation magnetization of these ternary magnetic MAX phases is almost two orders of magnitude higher than that of V2(Sn,Fe)C MAX phase whose A-site is partial substituted by Fe. Theoretical calculations on magnetic orderings of spin moments of Fe atoms in these nanolaminated magnetic MAX phases reveal that the magnetism can be mainly ascribed to intralayer exchange interaction of the 2D Fe atomic layers. Owning to the richness in composition of MAX phases, there is a large compositional space for constructing functional single-atom-thick 2D layers in materials using these nanolaminated templates.

The elemental diversity is crucial to screen out ternary MAX phases with outstanding properties via tuning of bonding types and strength between constitutive atoms. As a matter of fact, the interactions between M and A atoms largely determine the physical and chemical properties of MAX phases. Herein, Se element was experimentally realized to occupy the A site of a MAX phase, Zr2SeC, becoming a new member within this nanolaminated ternary carbide family. Comprehensive characterizations including Rietveld refinement of X-ray Diffraction and atom-resolved transmission electron microscopy techniques were employed to validate this novel MAX phase. The distinct thermal conduction behaviors emerged are attributed to the characteristic interactions between Zr and Se atoms.

The MAX phases are a family of of ternary layered material with both metal and ceramic properties, and it is also precursor ma-terials for synthesis of two-dimensional MXenes. The theory predicted that there are more than 600 stable ternary layered MAX phases. At present, there are more than 80 kinds of ternary MAX phases synthesized through experiments, and few reports on MAX phases where M is a rare earth element. In this study, a new MAX phase Sc2SnC with rare earth element Sc at the M sites was synthesized through the reaction sintering of Sc, Sn, and C mixtures. Phase composition and microstructure of Sc2SnC were confirmed by X-ray diffraction, scanning electron microscopy and X-ray energy spectrum analysis. And structural stability, mechanical and electronic properties of Sc2SnC was investigated via density functional theory. This study open a door for ex-plore more unknown ternary layered rare earth compounds Ren+1SnCn (Re=Sc, Y, La-Nd, n=1) and corresponding rare earth MXenes.

The class of two-dimensional metal carbides and nitrides known as MXenes offer a distinct manner of property tailoring for a wide range of applications. The ability to tune the surface chemistry for expanding the property space of MXenes is thus an important topic, although experimental exploration of new surface terminals remains a challenge. Here, we synthesized Ti3C2 MXene with unitary, binary and ternary halogen terminals, e.g. -Cl, -Br, -I, -BrI and -ClBrI, to investigate the effect of surface chemistry on the properties of MXenes. The electrochemical activity of Br and I element result in the extraordinary electrochemical performance of the MXenes as cathodes for aqueous zinc ion batteries. The -Br and -I containing MXenes, e.g. Ti3C2Br2 and Ti3C2I2, exhibit distinct discharge platforms with considerable capacities of 97.6 mAh g-1 and 135 mAh g-1. Ti3C2(BrI) and Ti3C2(ClBrI) exhibit dual discharge platforms with capacities of 117.2 mAh g-1 and 106.7 mAh g-1. In contrast, the previously discovered MXenes Ti3C2Cl2 and Ti3C2(OF) exhibit no discharge platforms, and only ~50% of capacities and energy densities of Ti3C2Br2. These results emphasize the effectiveness of the Lewis-acidic-melt etching route for tuning the surface chemistry of MXenes, and also show promise for expanding the MXene family towards various applications.

MAX phases are a family of layered, hexagonal-structure ternary carbides or nitrides of a transitional metal and an A-group element. What makes this type of material fascinating and potentially useful is their remarkable combinations of metallic and ceramic characteristics; as well as the indispensable role in 'top-down' synthesis of their 2D counterparts, MXenes. To enhance the efficiency in the successful search for potential novel MAX phases, the main efforts could go toward creating an informationprediction system incorporating all MAX phases' databases, as well as generally valid principles and the high-quality regularities. In this work, we employ structure mapping methodology, which has shown its merit of being useful guides in materials design, with Hume-Rothery parameters to provide guiding principles in the search of novel MAX phases. The formable/non-formable data on MAX phases can be ordered within a twodimensional plot by using proposed expression of geometrical and electron concentration factors.

Two-dimensional carbides and nitrides of transition metals, known as MXenes, are a fast-growing family of 2D materials that draw attention as energy storage materials. So far, MXenes are mainly prepared from Al-containing MAX phases (where A = Al) by Al dissolution in F-containing solution, but most other MAX phases have not been explored. Here, a redox-controlled A-site-etching of MAX phases in Lewis acidic melts is proposed and validated by the synthesis of various MXenes from unconventional MAX phase precursors with A elements Si, Zn, and Ga. A negative electrode of Ti3C2 MXene material obtained through this molten salt synthesis method delivers a Li+ storage capacity up to 738 C g-1 (205 mAh g-1) with high-rate performance and pseudocapacitive-like electrochemical signature in 1M LiPF6 carbonate-based electrolyte. MXene prepared from this molten salt synthesis route offer opportunities as high-rate negative electrode material for electrochemical energy storage applications.

Tailoring of individual single-atom-thick layers in nanolaminated materials offers atomic-level control over material properties. Nonetheless, multielement alloying in individual atomic layers in nanolaminates is largely unexplored. Here, we report a series of inherently nanolaminated V2(A'xSn1-x)C (A'=Fe, Co, Ni and Mn, and combinations thereof, with x=1/3) synthesized by an alloy-guided reaction. The simultaneous occupancy of the four magnetic elements and Sn, the individual single-atom-thick A layers in the compound constitute high-entropy-alloy analogues, two-dimensional in the sense that the alloying exclusively occurs in the A layers. V2(A'xSn1-x)C exhibit distinct ferromagnetic behavior that can be compositionally tailored from the multielement A-layer alloying. This two-dimensional alloying provides a structural-design route with expanded chemical space for discovering materials and exploit properties.

New MAX phases Ti2(AlxCu1-x)N and Nb2CuC were synthesized by A-site replacement by reacting Ti2AlN and Nb2AlC, respectively, with CuCl2 or CuI molten salt. X-ray diffraction, scanning electron microscopy, and atomically-resolved scanning transmission electron microscopy showed complete A-site replacement in Nb2AlC, which lead to formation of Nb2CuC. However, the replacement of Al in Ti2AlN phase was only close to complete at Ti2(Al0.1Cu0.9)N. Density-functional theory calculations corroborated the structural stability of Nb2CuC and Ti2CuN phases. Moreover, the calculated cleavage energy in these Cu-containing MAX phases are weaker than in their Al-containing counterparts, indicating that they are precursor candidates for MXene derivation., Comment: author name corrected

Nanolaminated materials are important because of their exceptional properties and wide range of applications. Here, we demonstrate a general approach to synthesize a series of Zn-based MAX phases and Cl-terminated MXenes originating from the replacement reaction between the MAX phase and the late transition metal halides. The approach is a top-down route that enables the late transitional element atom (Zn in the present case) to occupy the A site in the pre-existing MAX phase structure. Using this replacement reaction between Zn element from molten ZnCl2 and Al element in MAX phase precursors (Ti3AlC2, Ti2AlC, Ti2AlN, and V2AlC), novel MAX phases Ti3ZnC2, Ti2ZnC, Ti2ZnN, and V2ZnC were synthesized. When employing excess ZnCl2, Cl terminated MXenes (such as Ti3C2Cl2 and Ti2CCl2) were derived by a subsequent exfoliation of Ti3ZnC2 and Ti2ZnC due to the strong Lewis acidity of molten ZnCl2. These results indicate that A-site element replacement in traditional MAX phases by late transition metal halides opens the door to explore MAX phases that are not thermodynamically stable at high temperature and would be difficult to synthesize through the commonly employed powder metallurgy approach. In addition, this is the first time that exclusively Cl-terminated MXenes were obtained, and the etching effect of Lewis acid in molten salts provides a green and viable route to prepare MXenes through an HF-free chemical approach., Comment: Title changed; experimental section and discussion revised

It is well known that when the fused silica is irradiated with focused femtosecond laser beams, space selective chemical etching can be achieved. The etching rate depends sensitively on the polarization of the laser. Surprisingly, we observe that by chirping the Fourier-transform-limited femtosecond laser pulses to picosecond pulses, the polarization dependence of the etching rate disappears, whereas an efficient etching rate can still be maintained. Observation with a scanning electron microscope reveals that the chirped pulses can induce interconnected nanocracks in the irradiated areas which facilitates efficient introduction of the etchant into the microchannel. The reported technology is of great use for fabrication of three-dimensional (3D) microfluidic systems and glass-based 3D printing., Comment: 9 pages, 5 figures, 1 table

We develop a technique for realizing lithium niobate on insulator (LNOI) waveguides of a multi-centimeter-length with a propagation loss as low as 0.027 dB/cm. Our technique relies on patterning a chromium (Cr) thin film coated on the top surface of LNOI into a hard mask with a femtosecond laser followed by the chemo-mechanical polishing for structuring the LNOI into the waveguides. The surface roughness on the waveguides is determined to be 0.452 nm with an atomic force microscope (AFM). The approach is compatible with other surface patterning technologies such as optical and electron beam lithographies or laser direct writing, enabling high-throughput manufacturing of large-scale LNOI-based photonic integrated circuits., Comment: 9 pages, 4 figures

We report on fabrication of crystalline lithium niobate microresonators with quality factors above 10^7 as measured around 770 nm wavelength. Our technique relies on femtosecond laser micromachining for patterning a mask coated on the lithium niobate on insulate (LNOI) into a microdisk, followed by a chemo-mechanical polishing process for transferring the disk-shaped pattern to the LNOI. Nonlinear processes including second harmonic generation and Raman scattering have been demonstrated in the fabricated microdisk., Comment: 3 pages, 4 figures