Search

Almost a third of Earth’s freshwater resources are used by municipalities, agriculture and industries and therefore very large quantities of wastewater are generated and discharged into surface water or groundwater. If discharged inadequately and without previous treatment, wastewater can cause chemical pollution, affect aquatic life as well as human health and have a negative impact on the environment. An emerging technology for wastewater treatment is the membrane separation process due to the low cost, the use of ambient temperature, the low energy consumption compared to other traditional techniques, and the high selectivity of different separation mechanisms with compact design. In this study, ultrafiltration (UF) technique was investigated to treat wastewater with different organic loads. The effects of the stirring and a three-dimensional (3D) printed spacer, integrated into the UF cell were analyzed on the permeate fluxes, membrane rejections of turbidity, conductivity and chemical oxygen demand (COD).

Microwave irradiation is a promising pre-treatment method for sludge stabilisation, but there are few studies focusing its effect on organic matter solubility and biodegradability of wastewater and sludge originated from the food industry. In our research, microwave irradiation was applied standalone and in combination with alkaline treatment to enhance the solubilisation and biodegradation of organic matter content of meat industry wastewater and municipal sludge, respectively. The energy efficiency was investigated, as well. Dielectric measurement is a suitable method to detect physicochemical changes, therefore our research work covered the determination of dielectric properties of the investigated materials. Our experimental results have revealed that the lower power and energy intensity microwave-alkaline treatments were the most efficient pre-treatment process from energetically aspects to increase the organic matter solubility and biodegradability of wastewater and sludge. Furthermore, a strong linear correlation was found between the dielectric constant and the indicators of the solubility of organic matter (SCOD/TCOD) and aerobic biodegradability (BOD/COD) in both treated materials, respectively. Our results show that the dielectric measurements can be applied for detection of physicochemical changes, predict the improvement of biodegradability, and considered as a promising method to estimate the efficiency of sludge pre-treatment methods.

Wastewater issues became a complex challenge in the world. There are several methods in wastewater treatment, such as chemical, physical, biological, and the combination of each method. However, each process has advantages and disadvantages. The physicochemical methods are common methods used in wastewater treatment, such as adsorption and coagulation. Adsorption and coagulation are excellent methods to remove pollutants. The adsorption process is greatly influenced by pH, adsorbent dose, temperature, and contact time. Coagulant dose, settling time, and pH are the main factors in the coagulation process. Chemical material as an adsorbent and coagulant has been studied in previous research, but recently, to substitution chemical materials is a challenging subject. Natural substances are potential new materials in wastewater treatment and became popular due to their efficiency and environment friendly characteristics. This review investigated the role of adsorption and coagulation in wastewater treatment and the utilization of natural materials as adsorbents and coagulants.

This study investigates the enhancement of dairy wastewater treatment using chemical and physical pre-treatments coupled with membrane separation techniques to reduce membrane fouling. Two mathematical models, namely the Hermia and resistance-in-series module, were utilized to comprehend the mechanisms of ultrafiltration (UF) membrane fouling. The predominant fouling mechanism was identified by fitting experimental data into four models. The study calculated and compared permeate flux, membrane rejection, and membrane reversible and irreversible resistance values. The gas formation was also evaluated as a post-treatment. The results showed that the pre-treatments improved UF efficiency for flux, retention, and resistance values compared to the control. Chemical pre-treatment was identified as the most effective approach to improve filtration efficiency. Physical treatments after microfiltration (MF) and UF showed better fluxes, retention, and resistance results than ultrasonic pre-treatment followed by UF. The efficacy of a three-dimensionally printed (3DP) turbulence promoter was also examined to mitigate membrane fouling. The integration of the 3DP turbulence promoter enhanced hydrodynamic conditions and increased the shear rate on the membrane surface, shortening filtration time and increasing permeate flux values. This study provides valuable insights into optimizing dairy wastewater treatment and membrane separation techniques, which can have significant implications for sustainable water resource management. The present outcomes clearly recommend the application of hybrid pre-, main- and post-treatments coupled with module-integrated turbulence promoters in dairy wastewater ultrafiltration membrane modules to increase membrane separation efficiencies.

Since adsorption is one of the best ammonium removal methods, great efforts have been made to identify new low-cost and efficient adsorbents from agricultural waste and by-products due to their abundant availability, low-cost and eco-friendly advantages, in addition to the possibility of recycling ammonium back into agricultural processes. In this study, a series of batch experiments were performed to detect new bio-adsorbents for ammonium ions removal. Among the materials tested, pomegranate peel powder showed a high affinity to adsorb ammonium ions and, furthermore, available information on ammonium adsorption by this biomaterial is still missing from the literature. First, pomegranate peel powder was characterized by the determination of different parameters such as zeta potential, iodine number, Fourier-transform infrared spectroscopy analysis, scanning electron microscopy, particle size distribution and porosity. Then, the impact of various parameters, such as pH, contact time, stirring speed, adsorbent dose and adsorbate concentration in the adsorption process, was investigated. The highest ammonium removal capacity was obtained at pH = 4 using 400 mg of pomegranate peel powder and a stirring speed of 150 rpm for an initial concentration of ammonium of 30 mg/L. The system (adsorbent, adsorbate and solution) reached equilibrium after 2 h and the data fit well with the Langmuir model with a maximum monolayer adsorption capacity of 6.18 mg/g, while kinetics were well described by the pseudo-second-order model. These results introduce pomegranate peel powder as a promising bio-adsorbent to remove and recover ammonium from aqueous solutions.

A significant representative of the third generation of raw materials is waste containing hemicellulose. Agriculture and the food industry generate a great deal of this type of waste, which has many potential opportunities for processing. Our research group investigated the pre-treatments for the enzymatic saccharification of the cellulose content of the two fractions of corn cob meal. Microwave energy communication was performed in both acidic and alkaline media. It was found that the pH of the medium influences the amount of reducing sugars, but to an almost equal extent. The yield is also significantly dependent on the starting material and the concentration of the suspension.

The anaerobic digestion (AD) of wastewater sludge presents a promising and efficient method of wastewater and sludge treatment, as it can lower the organic content of sludge while producing a renewable source of energy—biogas—at the same time. However, using native, non-treated industrial wastewater sludge as a substrate for AD may present difficulties, hence we focused our research primarily on the applicability of measuring techniques—viscosity and dielectric measurement. One of our research goals was to investigate the presence of any connection between the aforementioned properties and the overall biogas production, in order to prove whether these measurement techniques were capable of monitoring the process of AD. Our other aim was to investigate how microwave (MW) pre-treatment affected the anaerobic fermentation. Our results revealed that in terms of total biogas yield, microwave irradiation could enhance fermentation by 14%, and also reduced the viscosity of the fermentation media by 13%. However, microwave irradiation did not change the overall tendencies of the AD process regarding these aspects. Moreover, it was discovered that dielectric and absolute viscosity measurements were effective methods for monitoring the fermentation. Additionally, a correlation was found between the accumulating biogas yield, the dielectric constant and loss factor, and the absolute viscosity of the digested media—each of these share a similarity in tendency and can indicate the occurrence of different phases during batch anaerobic fermentation.

Enhancing the performance of polymeric membranes by nanomaterials has become of great interest in the field of membrane technology. The present work aimed to fabricate polyvinylidene fluoride (PVDF)-hybrid nanocomposite membranes and modify them with TiO

Non-solvent induced phase-inversion is one of the most used methods to fabricate membranes. However, there are only a few studies supported by statistical analysis on how the different fabrication conditions affect the formation and performance of membranes. In this paper, a central composite design was employed to analyze how different fabrication conditions affect the pure water flux, pore size, and photocatalytic activity of polyvinylidene fluoride (PVDF) membranes. Polyvinylpyrrolidone (PVP) was used to form pores, and titanium dioxide (TiO2) to ensure the photocatalytic activity of the membranes. The studied bath temperatures (15 to 25 °C) and evaporation times (0 to 60 s) did not significantly affect the pore size and pure water flux of the membranes. The concentration of PVDF (12.5 to 17.5%) affected the viscosity, formation capability, and pore sizes. PVDF at high concentrations resulted in membranes with small pore sizes. PVP affected the pore size and should be used to a limited extent to avoid possible hole formation. TiO2 contents were responsible for the decolorization of a methyl orange solution (10−5 M) up to 90% over the period studied (30 h). A higher content of TiO2 did not increase the decolorization rate. Acidic conditions increased the photocatalytic activity of the TiO2-membranes.

In the present study, commercial PES, PVDF, PTFE ultrafilter membranes, and two different nanomaterial (TiO2 and TiO2/CNT composite)-covered PVDF ultrafilter membranes (MWCO = 100 kDa) were used for the purification of an industrial oil-contaminated (produced) wastewater, with and without ozone pretreatment to compare the achievable fouling mitigations by the mentioned surface modifications and/or pre-ozonation. Fluxes, filtration resistances, foulings, and purification efficiencies were compared in detail. Pre-ozonation was able to reduce the total filtration resistance in all cases (up to 50%), independently from the membrane material. During the application of nanomaterial-modified membranes were by far the lowest filtration resistances measured, and in these cases, pre-ozonation resulted in a slight further reduction (11–13%) of the total filtration resistance. The oil removal efficiency was 83–91% in the case of commercial membranes and > 98% in the case of modified membranes. Moreover, the highest fluxes (301–362 L m−2 h−1) were also measured in the case of modified membranes. Overall, the utilization of nanomaterial-modified membranes was more beneficial than pre-ozonation, but with the combination of these methods, slightly higher fluxes, lower filtration resistances, and better antifouling properties were achieved; however, pre-ozonation slightly decreased the oil removal efficiency.

Microbial number reduction in spices through various treatments represents a necessity considering possible changes which may occur during spices’ storage and application in food resulting in public health risk. The present study was conducted in order to examine the effects of sterilisation and microwave irradiation treatments on total mesophilic aerobic bacteria (TMAB) and bacterial spore content reduction in black pepper. Treatments applied were: sterilisation at 130 °C during 30, 60 and 90 min; and microwave irradiation at a power level of 600 W during 1.5, 3, and 5 min. Prolongation of the sterilisation treatment expressed positive influence on TMAB and bacterial spore reduction in black pepper. Compared to the sterilisation, microwave irradiation treatment exhibited better results in terms of black pepper decontamination. Maximal decontamination regarding TMAB and bacterial spore was achieved in black pepper samples treated with microwave irradiation during 3 min. The present results suggest that microwave irradiation could be applied in black pepper decontamination considering better effectiveness compared to the sterilisation treatment.

Sustainability of water use has got into focus recently, as availability of fresh water resources is under depletion. Population growth, extreme weather conditions (drought), increasing global meat demand all results in higher water consumption of humanity and ecosystem. Water footprint is a promising indicator, which assesses both qualitative and quantitative deterioration of fresh water supplies. By identifying blue, green and grey water components, water use can be assessed in a more comprehensive way. Furthermore impact assessment of different components during production and processing let us identify crucial points of water use, where more efficient solution should be found. As a consequence of a more conscious and sustainable water use assessment considering water footprint, there is a chance, that future generations will inherit fresh water supplies at least in the same condition as we got it from our ancestors.

In the present study, real car wash wastewater was purified by different coagulation/flocculation methods. As coagulant, polyaluminum chloride (‘BOPAC’), conventional iron(III) chloride, iron(III) sulfate, and aluminum(III) chloride were used, while as flocculant non-ionic and anionic polyelectrolytes were investigated. The effects of added clay mineral (Na-bentonite) and cationic surfactant (hexadecyltrimethyl ammonium bromide – ‘HTABr’) were also investigated. The use of BOPAC was significantly more effective than conventional coagulants. Extra addition of clay mineral was also beneficial in relation to both the sediment volume and sedimentation speed, while polyelectrolyte addition enhanced further the sedimentation. Moreover, the simultaneous addition of HTABr significantly enhanced the color removal efficiency due to the successful in-situ generation of organophilic bentonite. In summary, the application of 100 mg L−1 Na-bentonite with 20 mg L−1 Al3+ (from BOPAC) and 0.5 mg L−1 anionic polyelectrolyte resulted in the efficient reduction of the turbidity (4–6 NTU), the COD (158 mg L−1) and the extractable oil content (4 mg L−1) with efficiencies of 98%, 59%, and 85%, respectively. By applying organophilic bentonite in high concentration (500 mg L−1) with identical concentrations of BOPAC and anionic polyelectrolyte, significant color removal (5 times lower absorbance at λ = 400 nm) and 27% lower sediment volume were achieved.

Emulsified oily contaminants of wastewaters cannot be eliminated effectively by conventional treatments, but they pose significant risks both to the environment and to human health, therefore their...

Kutatasunk soran a mikrohullammal intenzifikalt Fenton-reakcio alkalmazhatosagat vizsgaltuk husipari szennyviz kezelese eseten. A kiserletek soran figyeltuk a Fenton-reakciohoz szukseges reagens (Fe2+ es H2O2) adagolasi dozisanak es a kozolt mikrohullamu energianak a kemiai oxigenigeny (KOI) csokkentesere (es igy a szervesanyag-tartalom csokkentesere) gyakorolt hatasat. A kutatasi eredmenyeink igazoltak, hogy a szervesanyag-eltavolitasi hatekonysag az alkalmazott Fe2+/H2O2 aranytol es az osszes kozolt MW energiatol is fugg. Magasabb dozisu Fenton-reagens nagyobb mertekű KOI-csokkenest eredmenyezett, a mikrohullamu energiakozles pedig kepes az oxidacios reakcio hatekonysagat novelni – magas kozolt MW energia eseten adott KOI-ertek csokkeneshez joval kevesebb reagens is elegendő volt. A kiserletek soran azt is igazoltuk, hogy a dielektromos vesztesegi szogtangens meresevel a szervesanyag-eltavolitas pontosan es konnyen nyomon kovethető. Abstract: Our experimental work focused on the applicability of microwave-assisted Fenton-reaction for wastewater treatment. We investigated the effects of Fenton’s reagent dosage and irradiated MW energy on the removal efficiency of chemical oxygen demand (COD). The results verified that organic matter removal efficiency is influenced by the Fe2+/H2O2 ratio and the microwave energy as well. Higher reagent dosage caused higher COD-removal, and it was proved that the microwave irradiation can enhance the efficiency of the oxidation process; the higher the MW energy was, the less reagent concentration was needed for reaching a given organic compound removal effectiveness. The experimental results also showed that measuring the dielectric loss tangent can be used to monitor the change in organic matter removal, i.e. the change in chemical oxygen demand.

Membrane-based methods of filtering are becoming increasingly popular in the food industry, but membrane fouling significantly affects filtration performance, making the characterisation of fouling mechanisms critical. This study examined the applicability of three mathematical models. The resistance-in-series model divides the total resistance into membrane resistance, reversible resistance and irreversible resistance. The Hermia models distinguish four basic blocking mechanisms, namely complete blocking, standard blocking, intermediate blocking and cake filtration. The Makardij model analyses the flux-reducing or -enhancing effects. In the experiments, different models were investigated and compared. The feed solution was two milk substitute drinks (soy and oat) that were ultrafiltered under different operating parameters (transmembrane pressures: 0.05–0.1 MPa, stirring rate: 100–400 min(−1)). By fitting the data to the models, the most characteristic blocking mechanism and the rate constant that most influenced flux could be determined.

Agricultural wastewater poses serious risks to the environment due to how it is injudiciously used and managed. We investigated the use of pomegranate peel powder (PPP) to adsorb ammonium ions from milking parlor wastewater, which is applied as a nitrogen source for cropland fertilization despite its environmental ramifications. As a valueless by-product of juice and jam industries, PPP shows promising features and characteristics as a potential bio-adsorbent for ammonium nitrogen removal and recovery. The surface characterization of PPP was performed by zeta potential measurement and attenuated total reflectance Fourier transform infrared Spectroscopy (ATR-FTIR) analysis. The adsorption studies were carried out by batch experiments where the initial ammonium nitrogen (NH4&ndash, N) concentration of studied wastewater was 80 mg/L. The effects of different operational parameters, such as pH, adsorbent dose, contact time, stirring speed, and temperature, were investigated. From kinetic studies, the equilibrium time was found to be 120 min, achieving an 81.8% removal synonym of ~2.5 mg/g NH4&ndash, N uptake. The adsorption isotherm data fitted well with Langmuir model with correlation (R2) &gt, 0.99. Meanwhile, the kinetics followed pseudo-second order model with correlation (R2) &gt, 0.99.

Sustainable water management is one of the biggest challenges in the 21st century as availability of fresh water resources is under depletion. Growing population, extreme weather conditions (drought, fire, flood), and increasing global food demand all result in higher water consumption by humans. Assessing qualitative and quantitative deterioration of fresh water supplies is crucial in water scarcity areas. By identifying blue, green and grey water components, water use can be assessed in a more comprehensive way. Water use assessment on a dairy farm is influenced by several factors such as chosen breed, herd size, keeping, feeding and milking technology. Productivity level of milking cows, amount of daily milking and type of litter (straw or liquid manure) have impact on water use by technology and cattle. If these factors are assessed and their proportion within the total water use is identified or calculated, dairy farmers are able to analyze water management precisely and shift to more sustainable solutions. The aim of this research is to analyze and to compare the impact of different keeping systems, i.e., traditional and modern, and milking technologies, i.e., robotic milking system, parallel and polygon parlors, on the water use of dairy farms to give a guide to dairy experts and to find opportunities where water recycling/reuse might be applicable.

Our experimental work focused on the applicability of a quite novel process for wastewater treatment, i.e. a microwave (MW) irradiation-enhanced Fenton-like method. The aim of our research was to detect and evaluate the efficiency of this oxidation process, during the treatment of meat industry wastewater containing a high concentration of organic material. The efficiency was defined by the measurement of the change in COD (chemical oxygen demand, with an initial COD value of 1,568 mg L−1), and with the determination of dielectric parameters during the process. It can be summarized that MW irradiation could assist in a Fenton-like oxidation process to achieve higher organic matter removal. Furthermore, our experimental results and statistical analysis show that there can be found a correlation between the effects of applied MW energy and the dosage of H2O2/FeSO4. If the intensity of MW irradiation and the amount of FeSO4 were set higher, the decrease of COD and the increase of tanδ (the dielectric loss tangent) were definitely more significant. With the application of 60 kJ MWE and a 0.14 mgFe2+/mgCOD dosage, the COD removal efficiency was more than 40%, and the increment of tanδ was nearly threefold. Considering the effects of MW-specific process parameters, it can be concluded that the power intensity of MW–oxidation treatment has a significant effect on COD decrease, if the irradiated MW energy was set at lower (30–45 kJ) levels.

Nutrient removal has become one of the key challenges for wastewater treatment facilities all over the world due to the harmful effect of these pollutants on water bodies and ecosystems known by eutrophication, however, most of the currently used technologies are not focused on nutrients recovery from wastewater. Recently, using agricultural waste/by-products for adsorption of nutrients acquired more interest because of their abundant availability, low-cost, high efficiency and eco-friendly advantages and this method may become more environmentally sustainable through maximizing removal while delivering nutrient and energy recovery technologies with economically attractive return on investment. This review investigates the application of agricultural waste/by-products as bio-sorbent for phosphate, ammonium and nitrate removal with a focus on the modification methods and the process mechanism including influent parameters, kinetics and isotherms.

For the effective purification of emulsified oil contaminated waters advanced treatment methods have to be applied, such as membrane filtration, which is able to eliminate macro-, and even nanoscale oil droplets, however, membrane fouling is still a major problem, which prevents economic utilization. Therefore, fouling mitigation is one of the most important aspects in the field of membrane separation developments. In the present study, solely TiO2 and TiO2/carbon nanotubes (CNT) composite modified PVDF membranes were prepared and used to purify oil-in-water emulsions. Achievable fluxes, reversible and irreversible filtration resistances, fouling models, filtration efficiencies and photocatalytic activities were compared in case of different nanomaterial covered and unmodified PVDF membranes. Applying either solely TiO2 or solely CNT coating resulted in the significant reduction of total filtration resistance in both cases, but the combination of the two components (TiO2 with 1 wt% CNT) resulted in by far the highest flux and lowest resistance, meanwhile, the enhanced photocatalytic efficiency of the composite was also achieved. To the best of our knowledge, this study demonstrates the beneficial effects of the combination of TiO2 and CNT nanomaterials for the first time in the field of membrane separation of oil-in-water emulsions.

Membrane separation processes are currently proven technologies in many areas. The main limitation of these processes is the accumulation of matter at the membrane surface which leads to two phenomena: concentration polarization and membrane fouling. According to the publications of numerous authors permeate flux could be increased by sonication. Our work focuses on separation of real broth by sonicated ultrafiltration. The broth was originated from hydrolysis of grounded corn-cob by xylanase enzyme. The filtration was carried out in a laboratory batch stirred cell with a sonication rod sonicator. In our work the effect of the stirring, the intensity of sonication and the membrane-transducer distance was studied on the efficiency of the ultrafiltration and on the quality of separated enzymes. Results reveal that xylanase enzyme can be effectively separated from real fermentation broth by ultrafiltration and enzymes keep their activity after the process. Enzyme activity tests show that low energy sonication is not harmful to the enzyme.

It has been numerously verified that microwave radiation could be advantageous as a pre-treatment for enhanced disintegration of sludge. Very few data related to the dielectric parameters of wastewater of different origins are available; therefore, the objective of our work was to measure the dielectric constant of municipal and meat industrial wastewater during a continuous flow operating microwave process. Determination of the dielectric constant and its change during wastewater and sludge processing make it possible to decide on the applicability of dielectric measurements for detecting the organic matter removal efficiency of wastewater purification process or disintegration degree of sludge. With the measurement of dielectric constant as a function of temperature, total solids (TS) content and microwave specific process parameters regression models were developed. Our results verified that in the case of municipal wastewater sludge, the TS content has a significant effect on the dielectric constant and disintegration degree (DD), as does the temperature. The dielectric constant has a decreasing tendency with increasing temperature for wastewater sludge of low TS content, but an adverse effect was found for samples with high TS and organic matter contents. DD of meat processing wastewater sludge was influenced significantly by the volumetric flow rate and power level, as process parameters of continuously flow microwave pre-treatments. It can be concluded that the disintegration process of food industry sludge can be detected by dielectric constant measurements. From technical purposes the applicability of dielectric measurements was tested in the purification process of municipal wastewater, as well. Determination of dielectric behaviour was a sensitive method to detect the purification degree of municipal wastewater.

In the present study, oil in water emulsions (coil = 100 ppm; doil droplets

Water is currently becoming a strategically important material, and the importance of water and wastewater treatment technologies is therefore increasing. Wastewater from the food industry has many special features originating from its high organic matter content. Meat industry wastewater additionally has a high fat content. We investigated the effects of ultrafiltration and ozonation, individually and in combination, for the treatment of meat industrial wastewater. Ozone gas was generated from oxygen with an Ozomatic Modular 4 ozone generator (Wedeco Ltd., Germany), and filtration was carried out with a micellar-enhanced ultrafiltration (MEUF) apparatus, through a flat membrane with a surface area of 40 cm2. The experimental data revealed that pre-ozonation of the wastewater affected ultrafiltration. The flux was higher and persisted longer than in the case of non-ozonated samples. The chemical oxygen demand was decreased by ozonation treatment. The duration of ozonation and the subsequent ultrafiltration exhibited a very interesting relationship. The most important effect of ozonation was observed on membrane fouling. The fouling mechanism was modelled, and the rate constants of flux decline (k1) and deposit removal from the membrane (k2) were calculated. The effect of the Reynolds number was also shown. The aim of our work was to study the industrial effects of combined cleaning techniques, i.e. ozonation on meat processing wastewater. The optimum ozonation time was 2 to 10 min before ultrafiltration with a PES membrane with a cut-off of 5 kDa.

This study investigated the adsorption of phosphate from aqueous solutions using pomegranate peel (PP) as a bio-adsorbent. For this purpose, PP was activated via saponification using sodium hydroxide (NaOH) followed by cationization using iron chloride (FeCl3). The iron-loaded PP (IL-PP) was characterized using zeta potential measurement, scanning electron microscopy, and Fourier transform infrared analysis. The batch adsorption method was followed to determine the equilibrium time and effect of pH on the adsorption process. The full factorial design methodology was used to analyze the effects of influencing parameters and their interactions. The effective removal of phosphate up to 90% was achieved within 60 min, at pH 9 and 25 °C temperature using a 150 mg dose of IL-PP. A non-linear method was used for the modeling of isotherm and kinetics. The results showed that the kinetics is best fitted to the Elovich model (R2 = 0.97), which assumes the dominance of the chemisorption mechanism, whereas the isotherm obeys both Langmuir (R2 = 0.98) and Freundlich (R2 = 0.94) models with a maximum phosphate uptake of 49.12 mg·g−1. Investigation of thermodynamic parameters indicated the spontaneity and endothermic nature of the process. These results introduce IL-PP as an efficient bio-adsorbent of phosphate.

In the present study, TiO2-coated ultrafiltration membranes were prepared and used for oily water filtration (droplet size

In the present work, the surface and filtration properties of TiO2 coated polyacrylonitrile ultrafiltration membranes were investigated. The membranes were coated using the physical deposition method. The appropriate TiO2 coverage proved to be 0.3 mg/cm2, which formed a hydrophilic cake layer on the membrane surface. The cleanability without chemicals and the retention of the coated membranes was compared to the neat membrane after model oily wastewater filtration. The cleaning sustained of rinsing with distilled water and ultraviolet (UV) irradiation of the fouled membranes. The coated membranes have better antifouling properties; higher flux values during oily water filtration and by the mentioned cleaning process a significantly better flux recovery can be achieved. The amount of the catalyst and the irradiation time are limiting factors to the effectiveness of the cleaning process. The UV irradiation increases the wettability of the fouled membrane surface by degrading the oil layer. The coating, the continuous use, and the cleaning process do not significantly affect the membrane retention expressed in chemical oxygen demand.

A mikrohullámú energiaközléses műveletek az élelmiszeripar, a vegyipar, a biotechnológia és a környezetvédelmi eljárások gyakorlatában is egyre inkább elterjednek. A mikrohullámú kezelési eljárások hatékonyságának részletesebb elemzése és a léptéknövelés azonban szükségessé tenné a folytonos anyagáramú kezelőrendszerekben végzett kísérletek végrehajtását. A kutatási munkánk során szennyvizek és iszapok biológiai hasznosíthatóságát befolyásoló szerkezeti és biológiai lebonthatósági változásokat vizsgáltuk folytonos anyagáramú mikrohullámú kezelések esetében. A vizsgálataink emellett kiterjedtek a mikrohullámú sugárzás hőkeltési hatékonyságát meghatározó dielektromos jellemzők mérésére is.