Search

Phase change materials (PCMs) are a class of thermo-responsive materials that can be utilized to trigger a phase transition which gives them thermal energy storage capacity. Any material with a high heat of fusion is referred to as a PCM that is able to provide cutting-edge thermal storage. PCMs are commercially used in many applications like textile industry, coating, and cold storage typically for heat control. These intriguing substances have recently been rediscovered and employed in a broad range of life science applications, including biological, human body, biomedical, pharmaceutical, food, and agricultural applications. Benefiting from the changes in physicochemical properties during the phase transition makes PCMs also functional for barcoding, detection, and storage. Paraffin wax and polyethylene glycol are the most commonly studied PCMs due to their low toxicity, biocompatibility, high thermal stability, high latent enthalpy, relatively wide transition temperature range, and ease of chemical modification. Current challenges in employing PCMs for life science applications include biosafety and/or engineering difficulties. The focus of this review article is on the life science applications, evaluation, and safety aspects of PCMs. Herein, the advances and the potential of employing PCMs as a versatile platform for various types of life science applications are highlighted.

The performance of latent thermal energy storage (LTES) heat exchangers is related to the stored energy (i.e. state of charge) during the (dis)charging of the energy storage system. Therefore, measuring the stored energy is crucial to understand the behavior of LTES systems. However, technical considerations often oppose the measurability of the stored energy. The present article presents a case where only measurements at the in- and outlet of the heat transfer fluid and on the outer surface of the heat exchanger were possible. Based on this sparse set of measurements, estimators for the stored energy are developed. To test these estimators, a finite volume model of the LTES heat exchanger is made. The finite volume model is fitted by comparing the predicted heat transfer fluid outlet temperature for 36 experiments. The energy estimators are compared to simulation results. The estimators for the stored energy in the heat transfer fluid, metal and phase change material obtain an average deviation of respectively 0.5 %, 3.9 % and 0.6 % with the stored energy predicted by the finite volume model. The estimator for the stored energy in the heat transfer fluid should be applicable to all LTES heat exchangers while the applicability of the estimators for stored energy in the metal and phase change material depend on small temperature differences between surface and interior of the metal and negligible heat losses.

A major challenge for the use of phase change materials (PCMs) in thermal energy storage (TES) is overcoming the low thermal conductivity of PCM’s. The low conductivity gives rise to limited power during charging and discharging TES. Impregnating metal foam with PCM, however, has been found to enhance the heat transfer. On the other hand, the effect of foam parameters such as porosity, pore size and material type has remained unclear. In this paper, the effect of these foam parameters on the solidification time is investigated. Different samples of PCM-impregnated metal foam were experimentally tested and compared to one without metal foam. The samples varied with respect to choice of material, porosity and pore size. They were placed in a rectangular cavity and cooled from one side using a coolant flowing through a cold plate. The other sides of the rectangular cavity were Polymethyl Methacrylate (PM) walls exposed to ambient. The temperature on the exterior walls of the cavity was monitored as well as the coolant flow rate and its temperature. The metal foam inserts reduced the solidification times by at least 25 %. However, the difference between the best performing and worst performing metal foam is about 28 %. This shows a large potential for future research. This study has received funding from European Union’s Horizon 2020 research and innovation programme under grant agreement Nº 657466 (INPATH-TES).

An organic phase change material (PCM) possesses the ability to absorb and release large quantity of latent heat during a phase change process over a certain temperature range. The use of PCMs in energy storage and thermal insulation has been tested scientifically and industrially in many applications. The broad based research and development studies concentrating on the characteristics of known organic PCMs and new materials as PCM candidates, the storage methods of PCMs, as well as the resolution of specific phase change problems, such as low thermal conductivity and supercooling have been reviewed. The potential industrial applications of PCMs in textiles and clothing systems, the methods of PCM integration into textiles and the methods of evaluating their thermal properties are also presented in this study. (C) 2012 Elsevier B.V. All rights reserved.