Search

Background: In pulmonary medicine, aerosolization of substances for continuous inhalation is confined to different classes of nebulizers with their inherent limitations. Among the unmet medical needs is the lack of an aerosolized surfactant preparation for inhalation by preterm neonates, to avoid the risks associated with endotracheal intubation and surfactant bolus instillation. In the present report, we describe a high-concentration continuous powder aerosolization system developed for delivery of inhalable surfactant to preterm neonates., Methods: The developed device uses a technique that allows efficient aerosolization of dry surfactant powder, generating a surfactant aerosol of high concentration. In a subsequent humidification step, the heated aerosol particles are covered with a surface layer of water. The wet surfactant aerosol is then delivered to the patient interface (e.g., nasal prongs) through a tube., Results: The performance characteristics of the system are given as mass concentration, dose rate, and size distribution of the generated aerosol. Continuous aerosol flows of about 0.84 L/min can be generated from dry recombinant surfactant protein-C surfactant, with concentrations of up to 12 g/m(3) and median particle sizes of the humidified particles in the range of 3 to 3.5 μm at the patient interface. The system has been successfully used in preclinical studies., Conclusion: The device with its continuous high-concentration delivery is promising for noninvasive delivery of surfactant aerosol to neonates and has the potential for becoming a versatile disperser platform closing the gap between continuously operating nebulizers and discontinuously operating dry powder inhaler devices.

The draft for a new United States Pharmacopoeia (USP) monograph {787} "Sub-visible Particulate Matter in Therapeutic Protein Injections" describes the analysis of sub-visible particles by light obscuration at much lower sample volumes as so far required by the European Pharmacopoeia (Ph. Eur.) and the USP for parenterals in general. Our aim was to show the feasibility of minimizing the sample expenditure required for light obscuration similar to the new USP settings for standards and pharmaceutically relevant samples (both proteins and small molecules), without compromising the data quality. The light obscuration method was downscaled from >20 ml volume as so far specified in Ph. Eur./USP to 1 ml total sample volume. Comparable results for the particle concentration in all tested size classes were obtained with both methods for polystyrene standards, stressed BSA solutions, recombinant human IgG1 formulations, and pantoprazol i.v. solution. An additional advantage of the low volume method is the possibility to detect vial-to-vial variations, which are leveled out when pooling several vials to achieve sufficient volume for the Ph. Eur./USP method. This is in particular important for biotech products where not only the general quality aspect, but also aggregate formation of the drug substance is monitored by light obscuration., (Copyright © 2013 Elsevier B.V. All rights reserved.)

Unlabelled: OBJECTIVES  The developments in combinatorial chemistry have led to a rapid increase in drug design and discovery and, ultimately, the production of many potential molecules that require evaluation. Hence, there has been much interest in the use of mathematical models to predict dermal absorption. Therefore, the aim of this study was to test the performance of both linear and nonlinear models to predict the skin permeation of a series of 11 compounds., Methods: The modelling in this study was carried out by the application of both quantitative structure permeability relationships and Gaussian process-based machine learning methods to predict the flux and permeability coefficient of the 11 compounds. The actual permeation of these compounds across human skin was measured using Franz cells and a standard protocol with high performance liquid chromatography analysis. Statistical comparison between the predicted and experimentally-derived values was performed using mean squared error and the Pearson sample correlation coefficient., Key Findings: The findings of this study would suggest that the models failed to accurately predict permeation and in some cases were not within two- or three-orders of magnitude of the experimentally-derived values. However, with this set of compounds the models were able to effectively rank the permeants., Conclusions: Although not suitable for accurately predicting permeation the models may be suitable for determining a rank order of permeation, which may help to select candidate molecules for in-vitro screening. However, it is important to note that such predictions need to take into account actual relative drug candidate potencies., (© 2012 The Authors. JPP © 2012 Royal Pharmaceutical Society.)

L-Arabinose isomerase (E.C. 5.3.1.14) catalyzes the reversible isomerization between L-arabinose and L-ribulose and is highly selective towards L-arabinose. By using a directed evolution approach, enzyme variants with altered substrate specificity were created and screened in this research. More specifically, the screening was directed towards the identification of isomerase mutants with L-ribose isomerizing activity. Random mutagenesis was performed on the Escherichia coli L-arabinose isomerase gene (araA) by error-prone polymerase chain reaction to construct a mutant library. To enable screening of this library, a selection host was first constructed in which the mutant genes were transformed. In this selection host, the genes encoding for L-ribulokinase and L-ribulose-5-phosphate-4-epimerase were brought to constitutive expression and the gene encoding for the native L-arabinose isomerase was knocked out. L-Ribulokinase and L-ribulose-5-phosphate-4-epimerase are necessary to ensure the channeling of the formed product, L-ribulose, to the pentose phosphate pathway. Hence, the mutant clones could be screened on a minimal medium with L-ribose as the sole carbon source. Through the screening, two first-generation mutants were isolated, which expressed a small amount of L-ribose isomerase activity.

Sophorolipids are surface-active compounds synthesized by a selected number of yeast species. They have been known for over 40 years, but because of growing environmental awareness, they recently regained attention as biosurfactants due to their biodegradability, low ecotoxicity, and production based on renewable resources. In this paper, an overview is given of the producing yeast strains and various aspects of fermentative sophorolipid production. Also, the biochemical pathways and regulatory mechanisms involved in sophorolipid biosynthesis are outlined. To conclude, a summary is given on possible applications of sophorolipids, either as native or modified molecules.

The genus Gluconobacter comprises some of the most frequently used microorganisms when it comes to biotechnological applications. Not only has it been involved in "historical" production processes, such as vinegar production, but in the last decades many bioconversion routes for special and rare sugars involving Gluconobacter have been developed. Among the most recent are the biotransformations involved in the production of L-ribose and miglitol, both very promising pharmaceutical lead molecules. Most of these processes make use of Gluconobacter's membrane-bound polyol dehydrogenases. However, recently other enzymes have also caught the eye of industrial biotechnology. Among them are dextran dextrinase, capable of transglucosylating substrate molecules, and intracellular NAD-dependent polyol dehydrogenases, of interest for co-enzyme regeneration. As such, Gluconobacter is an important industrial microbial strain, but it also finds use in other fields of biotechnology, such as biosensor-technology. This review aims to give an overview of the myriad of applications for Gluconobacter, with a special focus on some recent developments.

l-Ribulose is an important chiral lead molecule used for the synthesis of, among others, l-ribose, a high-value rare sugar used in the preparation of antiviral drugs. These drugs--nucleoside-analogues--gain importance in the treatment of severe viral diseases, like those caused by the HIV or hepatitis virus. In this study, factors that may have an impact on l-ribulose production with Gluconobacter oxydans and on the stability of l-ribulose were investigated. A bioconversion-type process, using washed resting cells, was chosen to produce l-ribulose from ribitol. In this process, the cell production and bioconversion phase were separated. The former was first optimized and a maximum cell mass of 1.5 g CDWL(-1) could be produced. For the bioconversion phase, the aeration level of the system proved to be one of the most critical factors; a maximal production rate of 15.7 g L(-1)h(-1) or 5.9 g(g CDW)(-1)h(-1) of l-ribulose could be reached. Furthermore, resting cells were found capable of completely converting ribitol solutions of up to 300 g L(-1) within 30 h, although the kinetics indicated a rather low affinity of the dehydrogenase enzymes for the substrate.

A new high performance liquid chromatographic (HPLC) method is described for the analysis of ribose, arabinose and ribulose mixtures obtained from (bio)chemical isomerization processes. These processes gain importance since the molecules can be used for the synthesis of antiviral therapeutics. The HPLC method uses boric acid as a mobile phase additive to enhance the separation on an Aminex HPX-87K column. By complexing with boric acid, the carbohydrates become negatively charged, thus elute faster from the column by means of ion exlusion and are separated because the complexation capacity with boric acid differs from one carbohydrate to another. Excellent separation between ribose, ribulose and arabinose was achieved with concentrations between 0.1 and 10 gL(-1) of discrete sugar.

As a halotolerant bacterial species, Brevibacterium epidermis DSM 20659 can grow at relatively high salinity, tolerating up to 2 M NaCl. It synthesizes ectoine and the intracellular content increases with the medium salinity, with a maximum of 0.14 g ectoine/g CDW at 1 M NaCl. Sugar-stressed cells do not synthesize ectoine. Ectoine synthesis is also affected by the presence of external osmolytes. Added betaine is taken up and completely replaced ectoine, while L-proline is only temporarily accumulated after which ectoine is synthesized. The strain can metabolize ectoine; L-glutamate is a better carbon source for ectoine synthesis than L-aspartate.

The aim of this study was to assess the potential of lactic acid bacteria to inhibit the outgrowth of some common food-spoiling fungi. Culture supernatants of 17 Lactic acid bacterial strains as well as of three commercial probiotic cultures were evaluated for antifungal activity using an agar-diffusion method. The method parameters were chosen in order to reveal compounds for potential use in food (bio)preservation. Thirteen strains showed antifungal activity of which five strains were very promising: Lactobacillus acidophilus LMG 9433, L. amylovorus DSM 20532, L. brevis LMG 6906, L. coryniformis subsp. coryniformis LMG 9196 and L. plantarum LMG 6907. Four of these five strains were further examined; it was found that the produced antifungal metabolites were pH-dependent. The exact chemical nature of these substances has not been revealed yet.

In this study sucrose laurate was formulated in hydrogels and investigated as a suitable transdermal penetration enhancer for oestradiol. Using rabbits as an animal model, the absolute bioavailability and the skin irritation were evaluated after single and multiple application. Three hydrogels containing 60 mg% oestradiol were evaluated: Oestrogel, and two hypromellose gels containing 5 and 15% sucrose laurate (w/w), respectively. No stability problem of the sucrose laurate was detected during a storage period of four months at 7 +/- 2 degrees C. After single application no significant difference (P < 0.05) was observed between the bioavailability parameters of Oestrogel and the 5% sucrose laurate gel. The values obtained for the 15% sucrose laurate gel were significantly higher than for the other gels. When applied on day 7 after a 6-day treatment, twice daily with the respective placebo gel, no significant difference was seen amongst the three formulations for any of the parameters evaluated. When the results after multiple application were compared with those after single application, a significant increase in oestradiol bioavailability was seen for the gel containing 30% ethanol and a significant decrease in oestradiol bioavailability was seen for the 5 and 15% sucrose laurate gels. Histological evaluation of the untreated and treated skin biopsies, showed a significantly higher incidence of infiltrate for all treated skin biopsies in comparison with the untreated ones. A significant increase in skinfold thickness was seen for the skin biopsies treated with gel containing 15% sucrose laurate. It can be concluded that sucrose laurate shows a potential as an absorption enhancer for percutaneous drug delivery.

Petrolatums from different manufacturers were characterized by viscosity measurements, oil number and ratio of low to high mol. wt components (capillary gas chromatography). Viscosity measurements and oil numbers of original materials did not correlate with the viscosity of the processed material in eye ointments. The ratio of high carbon number components to the low carbon number components was a reliable predictor for the viscosity of the formulation.

The influence of artificial light, daylight or stimulated sunlight on the stability of molsidomine was investigated. In static experiments an 80 micrograms mL-1 solution of molsidomine in saline was stored in an unprotected infusion bag. During dynamic experiments the molsidomine solution (80 micrograms mL-1) was dropped at 12.5 mL h-1 from an unprotected infusion bag, from an infusion bag covered with aluminium-foil, or from an infusion bag protected with a UV-cover. Either unprotected infusion tubing or infusion tubing with a UV-filter were connected to the infusion bags. Static as well as dynamic experiments showed a half-life of about 20 min for the unprotected molsidomine solutions, when placed behind a window during a sunny day. Protection from light of the infusion bag but not of the infusion tubing had only a minor influence on the drug half-life. Protection of the infusion bag and the infusion tubing with a UV-filter increased the half-life to several days. These results confirm that both the infusion bag and the infusion tubing need adequate light protection during molsidomine administration.

As several studies demonstrated the sorption of isosorbide dinitrate (ISDN) to intravenous delivery systems, a study on the sorption of ISDN to several central venous catheters was performed. Fourteen different catheters were perfused during a 2 h period, under simulated infusion conditions, with ISDN (250 micrograms mL-1) in 0.9% (w/v) sodium chloride. The drug loss to a polyethylene and a silicone catheter was 0.2 and 6.1%, respectively. The sorption to a polyvinylchloride heparin-coated thermodilution catheter was 1-6.9% depending on the length of the catheter. The drug loss to polyurethane catheters of different composition varied between 3.8 and 28.9%. For polyurethane catheters composed of cycloaliphatic polyurethanes an inverse relation was shown between Shore A hardness and sorption.

The in-vitro and in-vivo fluoride release of bioadhesive, slow-release tablets prepared from a mixture of polyethylene glycol polymers, containing 0.1 mg of fluoride as NaF was studied, and their ability to sustain fluoride levels in saliva were compared with conventional fluoride tablets with the same fluoride content. In-vitro release experiments showed that the bioadhesive tablets needed 8 h to release all their fluoride compared with less than 1 h for the conventional fluoride tablets. In-vivo, the bioadhesive tablets had a retention period of 6 h and could sustain a salivary fluoride level of more than 10 microM above the baseline for 7 h. The conventional fluoride tablets achieved a peak concentration of 0.5 mM directly after dissolution in the mouth, but the fluoride level could not be sustained for longer than 1 h. A good agreement was found between the in-vitro swelling behaviour of the bioadhesive tablets and their in-vitro and in-vivo release characteristics and their in-vivo retention time.

The bioavailability and pharmacokinetics of ibuprofen, a nonsteroidal antiinflammatory drug, was studied in healthy Shetland ponies. Ibuprofen was administered IV, as a suspension, and as a solid solution oral paste to ponies from which food was withheld. The suspension paste was also administered to ponies that received hay and water ad libitum. Both formulations had an absolute bioavailability of about 80%. Bioavailability was not influenced by feeding.

The influence of the composition of administration sets on the sorption of isosorbide dinitrate was investigated in-vitro. Isosorbide dinitrate solutions (250 micrograms mL-1) in 0.9% NaCl or 10% glucose were stored in glass containers and administered at a flow rate of 20 mL h-1. The influence of the concentration of different plasticizers (di-ethylhexylphthalate, tri-ethylhexyltrimelitate) in polyvinylchloride tubings was determined. Polybutadiene tubings of different mol. wt coextruded laminates of these polybutadienes with PVC of different composition and a polyethylene tubing were evaluated. The higher the Shore hardness of the PVC tubing, the lower the sorption. The infusion fluid played an additional role only for the tubings with high Shore hardness (greater than 70). The sorption of isosorbide dinitrate to polybutadiene tubings of different mol. wt was less than 2.5% after 5 h and was comparable with the sorption to the polyethylene tubing. When polybutadiene/PVC laminates were used, the sorption increased significantly and was in most cases dependent on the Shore hardness of the PVC (higher Shore hardness gave lower sorptions) and on the mol. wt of the polybutadiene (lower mol. wt resulted in higher sorption). Sorption was not dependent on the type of PVC plasticizer.

The bioadhesive characteristics of tablets for oral use made from modified starch, polyacrylic acid (PAA), polyethylene glycol (PEG) and sodium carboxymethylcellulose (CMC) were investigated. Adhesion force and energy were determined in-vitro and maximal adhesion time was evaluated in-vivo in human subjects. In-vitro, PAA showed the best bioadhesive properties, followed by modified maize starch and PEG with a mol. wt of 300,000-400,000 daltons. The presence of 0.1 mg of fluoride as NaF did not lead to significant differences in adhesion force and energy for the same formulation. The in-vivo bioadhesion was not strongly correlated to the in-vitro data. PAA, despite its excellent adhesion, proved to be irritating to the mucosa. PEG with a mol, wt of 200,000 daltons was subject to erosion. CMC showed good bioadhesive properties but the mechanical strength of the tablets was low. Modified maize starch tablets containing 5% (w/w) PAA and PEG with a mol. wt of 300,000 daltons proved to be the most suitable formulations for a fluoride-slow-release tablet with bioadhesive properties. In-vitro, the tablets released all of the fluoride within the 8 h period, with a high initial release. The release rate was related to the water absorption rate of the tablets. The PAA-containing formulations and the CMC formulations had the fastest release. In-vivo, fluoride levels with a minimum of 150 and a maximum of 1000 micrograms mL-1 were maintained for 8 h in the oral cavity. These fluoride levels were sustained significantly longer than those obtained with the administration of fourfold the amount of fluoride in the form of a fluoride-containing toothpaste. The release characteristics in-vivo exhibited a high variation. The use of bioadhesive polymers in oral pharmacotherapy seems promising.

The effect of suppository bases on rabbit rectal mucosa was investigated using six triglyceride bases, polyethylene glycol, and a triglyceride base combined with monoglycerides or fatty acids and methyl esters of those acids. Rectal irritation was evaluated and scored according to defined pathological features. "Pure" triglycerides and a triglyceride to which a nonionic surfactant was added caused severe mucosal damage with ulceration and inflammation. Hyperemia was characteristic for irritation by polyethylene glycol suppositories. Mucosal damage by a pure triglyceride combined with monoglycerides or fatty acids and methyl esters of those acids was similar but statistically less pronounced than with all other bases.