Search

Electron microscopy touches on nearly every aspect of modern life, underpinning materials development for quantum computing, energy and medicine. We discuss the open, highly integrated and data-driven microscopy architecture needed to realize transformative discoveries in the coming decade.

Oxygen defects govern the behavior of a range of materials spanning catalysis, quantum computing, and nuclear energy. Understanding and controlling these defects is particularly important for the safe use, storage, and disposal of actinide oxides in the nuclear fuel cycle, since their oxidation state influences fuel lifetimes, stability, and the contamination of groundwater. However, poorly understood nanoscale fluctuations in these systems can lead to significant deviations from bulk oxidation behavior. Here we describe the use of aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy to resolve changes in the local oxygen defect environment in [Formula: see text] surfaces. We observe large image contrast and spectral changes that reflect the presence of sizable gradients in interstitial oxygen content at the nanoscale, which we quantify through first-principles calculations and image simulations. These findings reveal an unprecedented level of excess oxygen incorporated in a complex near-surface spatial distribution, offering additional insight into defect formation pathways and kinetics during [Formula: see text] surface oxidation.

The sluggish oxygen evolution reaction (OER) remains a major bottleneck in hydrogen generation through electrolysis, particularly in large current operations. Thus, there is a huge interest in the development of highly active and robust non-noble metal-based OER catalysts. Herein, we report excellent catalytic performance of oxygen vacancy enriched, nano-porous Mn3O4/Ni/NiMnO3 architecture, synthesized in situ over a NiMn substrate through high-rate straining and chemical dealloying. The multiphase active surface exhibits significantly low overpotentials of only 262 mV and 282 mV even at high current densities of 500 mA cm−2 and 1000 mA cm−2, respectively. Our first-principles analysis revealed the prevalence of multi-site lattice oxygen-mediated pathways with two parallel mechanisms of direct evolution of O2, (a) facile cleavage of Ni–O bonds at the NiMnO3 surface and release of lattice oxygen and (b) activation of under-coordinated Mn–O polyhedra at the Ni/NiMnO3 interface and cleavage of OH groups by protonation of surface O atoms. The presence of oxygen vacancies leads to electronic reconstruction, further enhancing the adsorption kinetics of reaction intermediates. [ABSTRACT FROM AUTHOR]

A cementitious waste form, Cast Stone, is a possible candidate technology for the immobilization of low activity nuclear waste (LAW) at the Hanford site. This work focuses on the addition of getter materials to Cast Stone that can sequester Tc from the LAW, and in turn, lower Tc release from the Cast Stone. Two getters which produce different products upon sequestering Tc from LAW were tested: Sn(II) apatite (Sn-A) that removes Tc as a Tc(IV)-oxide and potassium metal sulfide (KMS-2) that removes Tc as a Tc(IV)-sulfide species, allowing for a comparison of stability of the form of Tc upon entering the waste form. The Cast Stone with KMS-2 getter had the best performance with addition equivalent to ∼0.08wt% of the total waste form mass. The observed diffusion (Dobs) of Tc decreased from 4.6±0.2×10-12cm2/s for Cast Stone that did not contain a getter to 5.4±0.4×10-13cm2/s for KMS-2 containing Cast Stone. It was found that Tc-sulfide species are more stable against re-oxidation within getter containing Cast Stone compared with Tc-oxide and is the origin of the decrease in Tc Dobs when using the KMS-2.

The degradation of the internal structure of plutonium (IV) oxalate during calcination was investigated with Transmission Electron Microscopy (TEM), electron diffraction, Electron Energy-Loss Spectroscopy (EELS), and 4D Scanning TEM (STEM). TEM lift-outs were prepared from samples that had been calcined at 300°C, 450°C, 650°C and 950°C. The resulting phase at all calcination temperatures was identified as PuO2 with electron diffraction. The grain size range was obtained with high-resolution TEM. In addition, 4D STEM images were analyzed to provide grain size distributions. In the 300°C calcined sample, the grains were <10 nm in diameter, at 650°C, the grains ranged from 10 to 20 nm, and by 950°C, the grains were 95-175 nm across. Using the Kolmogorov-Smirnov (K-S) two sample test, it was shown that morphological measurements obtained from 4D-STEM provided statistically significant distributions to distinguish samples at the different calcination conditions. Using STEM-EELS, carbon was shown to be present in the low temperature calcined samples associated with oxalate but had formed carbon (possibly graphite) deposits in the 950°C calcined sample. This work highlights the new methods of STEM-EELS and 4D-STEM for studying the internal structure of special nuclear materials (SNM). [ABSTRACT FROM AUTHOR]

We report the structural, vibrational, and optical properties of americium formate (Am(CHO2)3) crystals synthesized via the in situ hydrolysis of dimethylformamide (DMF). The coordination polymer features Am3+ ions linked by formate ligands into a three‐dimensional network that is isomorphous to several lanthanide analogs, (e. g., Eu3+, Nd3+, Tb3+). Structure determination revealed a nine‐coordinate Am3+ metal center that features a unique local C3v symmetry. The metal–ligand bonding interactions were investigated by vibrational spectroscopy, natural localized molecular orbital calculations, and the quantum theory of atoms in molecules. The results paint a predominantly ionic bond picture and suggest the metal‐oxygen bonds increase in strength from Nd−O