Search

In an attempt to develop reversible sensors based on ionic liquid/porous silicon (IL/pSi) platforms, we introduce an approach using task-specific, alkene-terminal ILs (AT-ILs) for direct grafting to the hydrogen-passivated as prepared-pSi (ap-pSi) surface via UV-hydrosilylation to address previous shortcomings associated with IL pattern impermanence (i.e., spread). By employing photoluminescence emission (PLE) and Fourier-transform infrared (FT-IR) imaging measurements, we demonstrate that the covalent grafting of AT-ILs onto the ap-pSi surface via photochemical hydrosilylation not only mitigates such feature spreading but also greatly improves PLE pattern stability. Significantly, we have discovered that, upon hydrosilylation, the resulting contact pin printed IL features remain stable to repeated challenges by toluene vapors, demonstrating the utility of AT-IL hydrosilylation for producing high-fidelity microarray features on pSi toward robust optical sensory microarrays.

Porous silicon (pSi) exhibits strong photoluminescence (PL) and its PL is often exploited for chemical sensor development. However, the sensor response is not uniform across a pSi specimen. We use co-localized confocal PL and Raman scattering mapping to establish a relationship between the analyte-induced PL response and the silicon nanocrystallite size, size distribution, and amorphous silicon (aSi) contribution across a pSi specimen. Using toluene as a model analyte, high analyte-induced PL response is associated with areas within the specimen that have (i) low aSi content, (ii) silicon nanocrystallites having diameters between 2 and 5 nm, and (iii) silicon nanocrystallites that exhibit a narrow size distributions (≤1% relative standard deviation).

Two-dimensional (2D) materials are being used widely for chemical sensing applications due to their large surface-to-volume ratio and photoluminescence (PL) emission and emission exciton band tunability. To better understand how the analyte affects the PL response for a model 2D platform, we used atomic force microscopy (AFM) and co-localized photoluminescence (PL) and Raman mapping to characterize tungsten disulfide (WS 2 ) flakes on template-stripped gold (TSG) under acetone challenge. We determined the PL-based response from single- and few-layer WS 2 arises from three excitons (neutral, A 0 ; biexciton, AA; and the trion, A - ). The A 0 exciton PL emission is the most strongly quenched by acetone whereas the A - PL emission exhibits an enhancement. We find the PL behavior is also WS 2 layer number dependent.

We demonstrate that gallium indium (GaIn) eutectic can be used to create interesting crystalline Si/porous silicon (cSi/pSi) platforms that exhibit unique analyte- and spatially-dependent photoluminescence (PL) responses. Here we characterize these cSi/pSi regions by using profilometry, scanning electron microscopy (SEM), wide-field PL microscopy, and Fourier transform infrared (FTIR) microscopy. As we move along a vector from the cSi/pSi interface out into "bulk" pSi, the: (i) analyte-dependent, PL-based response initially increases and then decreases; (ii) total PL emission intensity, in the absence of analyte, increases; (iii) pSi thickness increases; and (iv) relative O 2 Si-H to Si-H band amplitude ratio decreases. Thus, the analyte-dependent PL response magnitude is correlated to the extent of pSi oxidation; which can be easily controlled by using GaIn eutectic as a mask during the pSi fabrication process., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Porous silicon (pSi) based microarrays are attractive because pSi: (i) can be modified in many ways, (ii) possesses a high surface area, and (iii) exhibits strong photoluminescence (PL). These characteristics make pSi-based microarrays candidates for a host of applications including sensing, optoelectronic devices, and photodetectors. Microarray fabrication requires a high-throughput approach to produce chemically modified, spatially isolated spots on a particular substrate. The most stable platforms are characterized by covalent attachment to the substrate. In this paper we exploit the autocatalytic nature of 3-aminopropyltriethoxysilane (APTES) to contact pin-print APTES directly onto as prepared, H-passivated pSi (ap-pSi) without the need for a formal oxidation step. We assess the APTES-derived spots by using PL and Fourier transform infrared spectroscopy (FT-IR) imaging and determine the spot size and spatial homogeneity. All APTES-derived spots exhibited two distinct regions; a silanized core surrounded by an oxidized halo. By decreasing the APTES concentration and increasing the acid concentration, the oxidized halo size decreased by 60%; however, the silanized core diameter remains APTES and acid concentration independent. Bioconjugation can be achieved to all APTES-derived features; however, the highest biomolecule loading was realized by using pure APTES. Together these experiments demonstrate an easy and simple strategy for creating protein microarrays on pSi., (Copyright © 2017 Elsevier B.V. All rights reserved.)

We report on gaseous analyte-induced photoluminescence (PL) quenching of porous silicon, as-prepared (ap-pSi) and oxidized (ox-pSi). By using steady-state and emission wavelength-dependent time-resolved intensity luminescence measurements in concert with a global analysis scheme, we find that the analyte-induced quenching is best described by a three-component static quenching model. In the model, there are blue, green, and red emitters (associated with the nanocrystallite core and surface trap states) that each exhibit unique analyte-emitter association constants and these association constants are a consequence of differences in the pSi surface chemistries.

When xerogel films derived from carboxyethylsilanetriol (COE) and tetraethoxysilane (TEOS) or 3-aminopropyltriethoxysilane (APTES), n-octyltriethoxysilane (C8), and TEOS are formed on Al 2 O 3 they exhibit chemically segregated domains with unique chemistries and topographies. These characteristics are important for marine antifouling. By using the ratiometric fluorescent probe 5 (and 6)-carboxy SNARF-1 (C.SNARF-1) in concert with confocal fluorescence microscopy, we determine the pH in three dimensions within these hybrid films. For the COE/TEOS film, 4-5 μm diameter dendritically shaped features form, and they extend ∼100 nm above the film base. These dendritic features are acidic (pH < 7) in comparison to the film base. Their average diameter decreases as we progress from the solution-film interface toward the film-Al 2 O 3 interface. Planes located at the solution-film interface, film center, and film-Al 2 O 3 interface exhibit acidic surface areas that are 20% below, 50% above, and 70% below the average COE mole fraction used to create the film. In the APTES/C8/TEOS films, 1-3 μm diameter mesa-shaped features form, and they extend up to 450 nm above the film base. These mesa features are basic (pH > 7) in comparison to the film base and are columnar in shape, extending without change in diameter throughout the entire film. From the solution-film interface the planes located within the first 3/4 of the film exhibit basic surface areas that are equivalent to the average APTES mole fraction used to create the film. However, as one approaches the film-Al 2 O 3 interface, many new 100-200 nm basic subsurface regions appear. The basic surface area in those film planes within 400-500 nm of the film-Al 2 O 3 interface are enriched in APTES by up to 500% above the average APTES mole fraction used to create the film.

We report new instrumentation for rapidly and reliably measuring the temperature-dependent photoluminescence response from porous silicon as a function of analyte vapor concentration. The new system maintains the porous silicon under inert conditions and it allows on-the-fly steady-state and time-resolved photoluminescence intensity and hyper-spectral measurements between 293 K and 450 K. The new system yields reliable data at least 100-fold faster in comparison to previous instrument platforms., (© The Author(s) 2016.)

Surface patterns over multiple length scales are known to influence various biological processes. Here we report the synthesis and characterization of new, two-component xerogel thin films derived from carboxyethylsilanetriol (COE) and tetraethoxysilane (TEOS). Atomic force microscopy (AFM) reveals films surface with branched and hyper branched architectures that are ∼2 to 30 μm in diameter, that extend ∼3 to 1300 nm above the film base plane with surface densities that range from 2 to 77% surface area coverage. Colocalized AFM and Raman spectroscopy show that these branched structures are COE-rich domains, which are slightly stiffer (as shown from phase AFM imaging) and exhibit lower capacitive force in comparison with film base plane. Raman mapping reveals there are also discrete domains (≤300 nm in diameter) that are rich in COE dimers and densified TEOS, which do not appear to correspond with any surface structure seen by AFM.

We explore the size and spatial microheterogeneity of contact pin-printed spots formed on porous silicon (pSi). Glycerol was contact printed at room temperature onto as-prepared, hydrogen-passivated pSi (ap-pSi) using 50 or 200 µm diameter solid pins. The pSi was then subjected to a strong oxidizing environment (gaseous O 3 ) and washed to remove the glycerol masks. The glycerol-free regions were converted to oxidized pSi (ox-pSi); the glycerol-coated regions were protected from O 3 , but not entirely. The final array is described as circularly shaped "ap-pSi" regions on a field of ox-pSi. When comparing the areas outside and inside the glycerol-masked pSi spots, one finds dramatic differences in the Si-O-Si, SiH x (x = 1-3) and O y SiH x (y, x = 1-3) levels with a spatially dependent continuum of compositions across the spot diameter. Experimental conditions could be adjusted to tune the final ap-pSi spot diameter and edge widths from 90 µm to 520 µm and 20 µm to 130 µm, respectively. The resulting ap-pSi spot diameter is explained by using molecular kinetic theory and time-dependent glycerol imbibement into the pSi within a one-dimensional Darcy's law model., (© The Author(s) 2016.)

To develop ionic liquid/porous silicon (IL/pSi) microarrays we have contact pin-printed 20 hydrophobic and hydrophilic ionic liquids onto as-prepared, hydrogen-passivated porous silicon (ap-pSi) and then determined the individual IL spot size, shape and associated pSi surface chemistry. The results reveal that the hydrophobic ionic liquids oxidize the ap-pSi slightly. In contrast, the hydrophilic ionic liquids lead to heavily oxidized pSi (i.e., ox-pSi). The strong oxidation arises from residual water within the hydrophilic ILs that is delivered from these ILs into the ap-pSi matrix causing oxidation. This phenomenon is less of an issue in the hydrophobic ILs because their water solubility is substantially lower., (© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Microarrays of spatially isolated chemistries on planar surfaces are powerful tools. An important factor in microarray technology is the density of chemically unique spots that can be formed per unit area. In this paper, we use contact pin-printing and evaluate how to decrease contact pin-printed spot diameters on porous silicon (pSi) platforms. Using hydrosilylation chemistry to covalently attach chemistries to the pSi surface, the variables studied included pSi porosity and surface polarity, active agent viscosity, and pin diameter. The spot characteristics were assessed by Fourier transform infrared spectroscopy (FT-IR) microscopy and X-ray photoelectron spectroscopy (XPS). Spot size decreased as pSi porosity increased in accordance with molecular kinetic theory and Darcy's law of imbibition. Increasing active agent viscosity and pin diameter (volume of printed agent) led to larger spot diameters in accordance with molecular kinetic theory and Darcy's law. Oxidizing the pSi with H2O2 increased the surface polarity but had no detectable impact on the spot size. This is consistent with formation of an oxide layer atop an unoxidized pSi sublayer.

We synthesized sub-10 nm carbon nanoparticles (CNPs) consistent with photoluminescent carbon dots (C-dots) from carbon fiber starting material. The production of different C-dots fractions was monitored over seven days. During the course of the reaction, one fraction of C-dots species with relatively high photoluminescence was short-lived, emerging during the first hour of reaction but disappearing after one day of reaction. Isolation of this species during the first hour of the reaction was crucial to obtaining higher-luminescent C-dots species. When the reaction proceeded for one week, the appearance of larger nanostructures was observed over time, with lateral dimensions approaching 200 nm. The experimental evidence suggests that these larger species are formed from small C-dot nanoparticles bridged together by sulfur-based moieties between the C-dot edge groups, as if the C-dots polymerized by cross-linking the edge groups through sulfur bridges. Their size can be tailored by controlling the reaction time. Our results highlight the variety of CNP products, from sub-10 nm C-dots to ~200 nm sulfur-containing carbon nanostructures, that can be produced over time during the oxidation reaction of the graphenic starting material. Our work provides a clear understanding of when to stop the oxidation reaction during the top-down production of C-dots to obtain highly photoluminescent species or a target average particle size.

Multipurpose solutions (MPS) are a single solution that functions to simultaneously rinse, disinfect, clean, and store soft contact lenses. Several commercial MPS products contain polyhexamethylene biguanide (PHMB) and/or polyquaternium-1 (PQ-1) as antimicrobial agents. In this paper we have created an in vitro small unilamellar vesicle (SUV) model of the corneal epithelial surface, and we have assessed the interactions of PHMB and PQ-1 with several model biomembranes by using fluorescence spectroscopy, dynamic light scattering (DLS), and liquid chromatography-mass spectrometry (LC-MS). Steady-state and time-resolved fluorescence were used to assess the membrane acyl chain and polar headgroup region local microenvironment as a function of added PHMB or PQ-1. DLS was used to detect and quantify SUV aggregation induced by PHMB and PQ-1. LC-MS was used to determine the liposomal composition from any precipitated materials in comparison to the as-prepared SUVs. The results are consistent with PHMB adsorbing onto and PQ-1 intercalating into the biomembrane structure. The differences between the two interaction mechanisms have substantial impacts on the biomembrane dynamics and stability.

We report a complementary metal oxide semiconductor integrated circuit (CMOS IC) with a buried double junction (BDJ) photodiode that (i) provides a real-time output signal that is related to the intensity ratio at two emission wavelengths and (ii) simultaneously eliminates the need for an optical filter to block Rayleigh scatter. We demonstrate the BDJ platform performance for gaseous NH3 and aqueous pH detection. We also compare the BDJ performance to parallel results obtained by using a slew scanned fluorimeter (SSF). The BDJ results are functionally equivalent to the SSF results without the need for any wavelength filtering or monochromators and the BDJ platform is not prone to errors associated with source intensity fluctuations or sensor signal drift., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Over the past decade there has been significant development in hybrid polymer coatings exhibiting tunable surface morphology, surface charge, and chemical segregation-all believed to be key properties in antifouling (AF) coating performance. While a large body of research exists on these materials, there have yet to be studies on all the aforementioned properties in a colocalized manner with nanoscale spatial resolution. Here, we report colocalized atomic force microscopy, scanning Kelvin probe microscopy, and confocal Raman microscopy on a model AF xerogel film composed of 1:9:9 (mol:mol:mol) 3-aminopropyltriethoxysilane (APTES), n-octyltriethoxysilane (C8), and tetraethoxysilane (TEOS) formed on Al2O3. This AF film is found to consist of three regions that are chemically and physically unique in 2D and 3D across multiple length scales: (i) a 1.5 μm thick base layer derived from all three precursors; (ii) 2-4 μm diameter mesa-like features that are enriched in free amine (from APTES), depleted in the other species and that extend 150-400 nm above the base layer; and (iii) 1-2 μm diameter subsurface inclusions within the base layer that are enriched in hydrogen-bonded amine (from APTES) and depleted in the other species.

We report a new strategy for generating a continuum of response profiles from a single luminescence-based sensor element by using phase-resolved detection. This strategy yields reliable responses that depend in a predictable manner on changes in the luminescent reporter lifetime in the presence of the target analyte, the excitation modulation frequency, and the detector (lock-in amplifier) phase angle. In the traditional steady-state mode, the sensor that we evaluate exhibits a linear, positive going response to changes in the target analyte concentration. Under phase-resolved conditions the analyte-dependent response profiles: (i) can become highly non-linear; (ii) yield negative going responses; (iii) can be biphasic; and (iv) can exhibit super sensitivity (e.g., sensitivities up to 300 fold greater in comparison to steady-state conditions).

In this article we review the mechanism of ocular surface staining. Water-soluble dyes are excluded from the normal epithelium by tight junctions, the plasma membranes and the surface glycocalyx. Shed cells can take up dye. A proportion of normal corneas show sparse, scattered time-dependent, punctate fluorescein uptake, which, we hypothesise, is due to a graded loss of the glycocalyx barrier, permitting transcellular entry into pre-shed cells. In pathological staining, there is little evidence of 'micropooling' at sites of shedding and the term 'punctate erosion' may be a misnomer. It is more likely that the initial event involves transcellular dye entry and, in addition, diffusion across defective tight junctions. Different dye-staining characteristics probably reflect differences in molecular size and other physical properties of each dye, coupled with differences in visibility under the conditions of illumination used. This is most relevant to the rapid epithelial spread of fluorescein from sites of punctate staining, compared to the apparent confinement of dyes to staining cells with dyes such as lissamine green and rose bengal. We assume that fluorescein, with its lower molecular weight, spreads initially by a paracellular route and then by transcellular diffusion. Solution-Induced Corneal Staining (SICS), related to the use of certain contact lens care solutions, may have a different basis, involving the non-pathological uptake of cationic preservatives, such as biguanides, into epithelial membranes and secondary binding of the fluorescein anion. It is transient and may not imply corneal toxicity. Understanding the mechanism of staining is relevant to the standardisation of grading, to monitoring disease and to the conduct of clinical trials., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

An investigation into the performance of luminescence-based hyperspectral imaging (LHSI) for denim fiber bundle discrimination has been conducted. We also explore the potential of nitromethane (CH3NO2) -based quenching to improve discrimination, and we determine the quenching mechanism. The luminescence spectra (450-850 nm) and images from the denim fiber bundles were obtained with excitation at 325 or 405 nm. LHSI data were recorded in less than 5 s and subsequently assessed by principal component analysis or rendered as red, green, blue (RGB) component histograms. The results show that LHSI data can be used to rapidly and uniquely discriminate between all the fiber bundle types studied in this research. These non-destructive techniques eliminate extensive sample preparation and allow for rapid hyperspectral image collection, analysis, and assessment. The quenching data also revealed that the dye molecules within the individual fiber bundles exhibit dramatically different accessibilities to CH3NO2.

As the third-generation rigid macrocycles evolved from progenitor 1 , cyclic aromatic oligoamides 3 , with a backbone of reduced constraint, exhibit extremely strong stacking with an astoundingly high affinity (estimated lower limit of K dimer > 10 13 M -1 in CHCl 3 ), which leads to dispersed tubular stacks that undergo further assembly in solution. Computational study reveals a very large binding energy (-49.77 kcal mol -1 ) and indicates highly cooperative local dipole interactions that account for the observed strength and directionality for the stacking of 3 . In the solid-state, X-ray diffraction (XRD) confirms that the aggregation of 3 results in well-aligned tubular stacks. The persistent tubular assemblies of 3 , with their non-deformable sub-nm pore, are expected to possess many interesting functions. One such function, transmembrane ion transport, is observed for 3 .

Tetracyclines (TCs), broad spectrum antibiotics widely used in the prevention and treatment of infectious diseases, are amphoteric molecules containing several ionizable functional groups that exist predominantly as zwitterions at a given pH value. TCs are reported to undergo a wide variety of reactions at different pH values i.e. TCs form to anhydrotetracyclines at low pH, 4-epitetracyclines at pH 3-5 and isotetracyclines at high pH values. The pH-dependent absorbance and emission properties of tetracycline and its 10 analogs (4-epitetracycline, doxycyline, oxytetracycline, chlortetracycline, 4-epichlortetracycline, isochlortetracycline, methacycline, rolitetracycline, minocycline, and demeclocycline) were investigated and reported in this paper. The main focus of the study was on the pH dependent transformation of epichlortetracycline, chlortetracycline and isotetracycline at basic pH. Absorption, emission and time resolved spectroscopy were used to determine the behavior of the three TC derivatives at this condition. Increasing the buffer's ionic concentration leads to faster transformation to iCTC. A pH dependent transformation of CTC to iCTC was observed and the lifetimes of CTC and iCTC were determined to be 3.0 and 5.89 ns respectively. The distribution factor of CTC to iCTC at basic pH was also reported for the first time.

Development of long-term implantable luminescent biosensors for subcutaneous oxygen has proved challenging due to difficulties in immobilizing a biocompatible matrix that prevents sensor aggregation yet maintains sufficient concentration for transdermal optical detection. Here, Pd-porphyrins can be used as PEG cross-linkers to generate a polyamide hydrogel with extreme porphyrin density (≈5 × 10(-3) m). Dye aggregation is avoided due to the spatially constraining 3D mesh formed by the porphyrins themselves. The hydrogel exhibits oxygen-responsive phosphorescence and can be stably implanted subcutaneously in mice for weeks without degradation, bleaching, or host rejection. To further facilitate oxygen detection using steady-state techniques, an oxygen-non-responsive companion hydrogel is developed by blending copper and free base porphyrins to yield intensity-matched luminescence for ratiometric detection., (© 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Programmed self-assembly of well-defined molecular building blocks enables the fabrication of precisely structured nanomaterials. In this work, we explore a new class of giant polymeric surfactants (Mn = (0.7-4.4) × 10(6) g/mol) with bottlebrush architecture and show that their persistent molecular shape leads to the formation of uniform aggregates in a predictable manner. Amphiphilic bottlebrush block copolymers containing polylactide (PLA) and poly(ethylene oxide) (PEO) side chains were synthesized by a grafting-from method, and their self-assembly in aqueous environment was studied by cryogenic transmission electron microscopy. The produced micelle structures with varying interfacial curvatures and core radii (19-55 nm) boasted rod-like hydrophilic PEO brushes protruding from the hydrophobic PLA cores normal to the interface. Highly uniform spherical micelles with low dispersities were obtained from bottlebrush amphiphiles with packing parameters of ∼0.3, estimated from the polymer structural data. Long cylindrical micelles and other nonspherical aggregates were observed for the first time for compositionally less asymmetric bottlebrush surfactants. Critical micelle concentration values of 1 nM, measured for PEO-rich bottlebrush amphiphiles, indicated an enhanced thermodynamic stability of the produced micelle aggregates. Shape-dependent assembly of bottlebrush surfactants allows for the rational fabrication of a range of micelle structures in narrow morphological windows.

Biofouling on ships and boats, characterized by aquatic bacteria and small organisms attaching to the hull, is an important global issue, since over 80000 tons of antifouling paint is used annually. This biofilm, which can form in as little as 48 hours depending on water temperature, increases drag on watercraft, which greatly reduces their fuel efficiency. In addition, biofouling can lead to microbially induced corrosion (MIC) due to H2S formed by the bacteria, especially sulfate-reducing bacteria. When the International Maritime Organization (IMO) international convention banned the use of effective but environmentally damaging coatings containing tributyl tin in 2008, the development of clean and effective antifouling systems became more important than ever. New nonbiocidal coatings are now in high demand. Scientists have developed new polymers, materials, and biocides, including new elastomeric coatings that they have obtained by improving the original silicone (polydimethylsiloxane) formulation patented in 1975. However, the high cost of silicones, especially of fluoropolymer-modified silicones, has generally prevented their large-scale diffusion. In 2009, traditional antifouling coatings using cuprous oxide formulated in copolymer paints still represented 95% of the global market volume of anti-fouling paints. The sol-gel nanochemistry approach to functional materials has emerged as an attractive candidate for creating low fouling surfaces due to the unique structure and properties of silica-based coatings and of hybrid inorganic-organic silicas in particular. Sol-gel formulations easily bind to all types of surfaces, such as steel, fiberglass, aluminum, and wood. In addition, they can cure at room temperature and form thin glassy coatings that are markedly different from thick silicone elastomeric foul-releasing coatings. Good to excellent performance against biofouling, low cure temperatures, enhanced and prolonged chemical and physical stability, ease of application, and the waterborne nature of sol-gel coatings all support the diffusion of these paints to efficiently reduce the accumulation of fouling layers on valued surfaces immersed in marine or fluvial waters. Furthermore, sol-gel glassy coatings are transparent and can be effectively applied to optical devices, windows, and solar panels used in lake, fluvial, or marine environments. Sol-gel technology is eminently versatile, and the first generation sol-gel paints have already shown good performance. Even so, vast opportunities still exist for chemists to develop novel sol-gel derived coatings to both prevent biofouling and enhance the hydrodynamic properties of boat and ship hulls. Moreover, researchers have prepared and applied multifunctional sol-gel coatings providing protection against both biofouling and corrosion. They have tested these in the marine environment with good preliminary results. In this Account, we discuss some of our new strategies for the controlled functionalization of surfaces for the development of efficient antifouling and foul-releasing systems and summarize the main achievements with biocidal and nonbiocidal sol-gel coatings. We conclude by giving insight into the marine coatings and sol-gel products markets, providing arguments to justify our conclusion that the sol-gel coatings technology is now a mature platform for the development of economically viable and environmentally friendly antifouling and foul-release formulations of enhanced performance.

A complex of salmon milt deoxyribonucleic acid (DNA) and the cationic surfactant cetyltrimethylammonium (CTMA) forms an organic-soluble biomaterial that can be readily incorporated within an organically modified silane-based xerogel. The photoluminescence (PL) intensity and excited-state luminescence lifetime of tris(4,7'-diphenyl-1,10'-phenanathroline) ruthenium(II) [(Ru(dpp)3](2+), a common O2 responsive luminophore, increases in the presence of DNA-CTMA within the xerogel. The increase in the [Ru(dpp)3](2+)excited-state lifetime in the presence of DNA-CTMA arises from DNA intercalation that attenuates one or more non-radiative processes, leading to an increase in the [Ru(dpp)3](2+) excited-state lifetime. Prospects for the use of these materials in an oxygen sensor are demonstrated.

We carefully tailored a porous silicon (pSi) surface by oxidation with hydrogen peroxide (H2O2) to determine the time-dependent changes in nanocrystallite surface chemistries (e.g., Si-O-Si, SiH(x) [x = 1, 2], OySiH [y = 2, 3], and SiOH/H2O) and their influence on the pSi photoluminescence (PL). The relationship between infrared band amplitudes and PL intensity were evaluated under H2O2 and O3 (previously studied) oxidation. The pSi surface composition under O3 and H2O2 oxidation conditions tended to, save the O(y)SiH (y = 2, 3) species, approach similar values at the longest oxidation times studied, but they took very different paths in reaching these end points. Furthermore, the pSi surface compositions that exhibit maximum/minimum PL under each oxidant are very different.

Carbon dots (C-dots) are often synthesized, modified, and studied as a mixture. Unfortunately, the spectroscopic and biological properties measured for such C-dots assume that there is a high degree of homogeneity in the produced sample. By means of high-resolution separation techniques, we show that "as-synthesized" C-dots exist as a relatively complex mixture and that an unprecedented reduction in such complexity can reveal fractions of C-dots with unique luminescence properties. The wavelength-dependent photoluminescence commonly assigned as an inherent property of C-dots is not present in fractionated samples. While ultraviolet-visible absorption profiles reported for C-dots are typically featureless, we have found fractions of C-dots possessing unique absorption bands, with different fractions possessing specific emission wavelengths. Furthermore, fractionated C-dots showed profound differences in emission quantum yield, allowing for brighter C-dots to be isolated from an apparent low quantum yield mixture. These more luminescent fractions of C-dots displayed improved biological compatibility and usefulness as cellular imaging probes.

As our understanding of the eye and how it works evolves, we must re-evaluate previous findings, beliefs, and methods of diagnosis and treatment. The eye has proven to be naturally adept at protecting itself from pathogenic intruders, but contact lens wear and lens cleaning products can adversely impact this innate ability. Keeping up to date on the latest information is challenging, and becomes more complex when trying to incorporate the new scientific data into clinical practice. Several factors prevent drawing a straight line from study findings to real-world results, such as patient compliance and potentially flawed diagnostic tools. In this section, we review the latest research findings and opinions related to contact lens care and further explore compliance and its effect on ocular health., (Copyright © 2013 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.)

Eye care practitioners (ECPs) would tend to agree that wearing contact lenses increases the risk for infection, but millions of patients are still fitted with lenses every year because ECPs feel that the risk is manageable and that their patients' eye health can be protected. The Fusarium and Acanthamoeba keratitis outbreaks of years past were a wake-up call to manufacturers, ECPs, and regulatory agencies that risk cannot be managed without diligence, and that the complex relationship between contact lens materials, contact lens solutions, and compliance needs to be better understood in order to optimize the efficacy of contact lens care and improve care guidelines., (Copyright © 2013 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.)

The early focus of contact lens wear and ocular health was on oxygen delivery. However, as we learn more about how the eye works, and investigate how the contact lens interacts with the cornea, the role of the tear film has risen in prominence. A healthy tear film is critical for normal ocular homeostasis, and abnormalities of the tear film are the primary cause of dry eye. In order to improve patient eye health and comfort during lens wear, we need to further elucidate the relationship among contact lenses, contact lens solutions, the tear film, and the corneal epithelium, and find ways to maintain homeostasis of the ocular surface. In this section, we review the latest data and opinions on this complex relationship between contact lenses and lens care solutions., (Copyright © 2013 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.)

We present a custom CMOS IC with a buried double junction (BDJ) photodiode to detect and process the optical signal, eliminating the need for any off-chip optical filters. The on-chip signal processing circuitry improves the desired signal extraction from the optical background noise. Since the IC is manufactured using standard commercial fabrication processes with no post-processing necessary, the system can ultimately be low cost to fabricate. Additionally, because of the CMOS integration, it will consume little power when operating, and even less during stand-by.

Purpose: Multipurpose contact lens solution (MPS)/preservative-associated transient corneal hyperfluorescence has been suggested to represent corneal injury. To determine the validity of this assumption, the molecular-level interactions of common disinfectants in soft contact lens MPS and the corneal epithelium using an in vitro model were assessed., Methods: A liposome-based model of the corneal epithelial surface was developed and used to assess the interactions of polyhexamethylene biguanide (PHMB), polyquaternium-1 (PQ-1), and fluorescein with membrane components and the effects of PHMB and PQ-1 on membrane integrity. The fluorescence anisotropy (a measure of interactions between molecules) was determined. Liposome integrity was assessed by measuring the liposome melting point temperature., Results: Free fluorescein did not associate with the liposome (P>0.4). Both fluorescein-tagged PHMB and PQ-1 associated with liposomes (P<0.002 and P≤0.01, respectively); however, only PHMB induced free fluorescein association with membrane components. At physiological temperature, no significant shift in the melting point temperature was observed when liposomes were exposed to PHMB from 0 to 100 ppm (P>0.05). In contrast, exposure of >7 ppm PQ-1 disrupted the liposomes., Conclusions: Based on this study, PHMB-to-liposome bilayer interaction is nondestructive, even at concentrations 100 times higher than found in commercially available MPS products. In contrast, PQ-1-to-liposome bilayer interaction led to liposome disruption. This study presents molecular-level evidence to support that preservative-associated transient corneal hyperfluorescence is a benign transient phenomenon and its evaluation clinically may be an ambiguous strategy for determining biocompatibility and cell surface integrity.

A high-throughput screening system has been developed to rapidly produce, screen, and assess the usefulness of organically modified silane (ORMOSIL)-based xerogel films formed on the surface of porous silicon (pSi) surfaces. The ORMOSILs tested include methyltriethoxysilane, n-octyltriethoxysilane, n-hexyltriethoxysilane, n-propyltriethoxysilane, 2-cyanoethyltriethoxysilane, phenyltriethoxysilane, benzyltriethoxysilane, vinyltriethoxysilane, tetraethoxysilane, and hexafluoroethyltriethoxysilane. Xerogel microarrays were pin-printed on the surface of O(3) oxidized pSi using a computer-controlled robotic pin-printer. The fragile pSi required careful pin-printing parameter optimization to simultaneously ensure sufficient sol application and limit pin-induced damage. These multi-functional xerogel-pSi microarrays were exposed to harsh conditions (0.1 mM NaOH, 15 min) to determine the extent to which the xerogel protected the pSi. Microarray assessment included multispectral photoluminescence and infrared imaging. Results demonstrate that the more hydrophobic/nonpolar xerogel films (n-octyltriethoxysilane, n-hexyltriethoxysilane) protect the pSi surface the most and maintained the pSi photoluminescence. Also, unlike xerogel material doped with a reporter molecule, the uniformity of the printed feature plays a role in the protection of the pSi material underneath. Areas with thinner xerogel distributions allowed the permeation of NaOH whereas the thicker areas prohibit pSi exposure to NaOH.

We carefully evaluate how porous silicon (pSi) surface oxidation by ozone (O(3)) and the resulting changes in nanocrystallite surface chemistries (e.g., SiOSi, SiH(x) (x = 1-3), O(y)SiH (y = 1-2), and SiOH) influence the pSi photoluminescence (PL). We discover a relationship between the pSi PL and the O(2)SiH band amplitude.

A long-standing aim in molecular self-assembly is the development of synthetic nanopores capable of mimicking the mass-transport characteristics of biological channels and pores. Here we report a strategy for enforcing the nanotubular assembly of rigid macrocycles in both the solid state and solution based on the interplay of multiple hydrogen-bonding and aromatic π-π stacking interactions. The resultant nanotubes have modifiable surfaces and inner pores of a uniform diameter defined by the constituent macrocycles. The self-assembling hydrophobic nanopores can mediate not only highly selective transmembrane ion transport, unprecedented for a synthetic nanopore, but also highly efficient transmembrane water permeability. These results establish a solid foundation for developing synthetically accessible, robust nanostructured systems with broad applications such as reconstituted mimicry of defined functions solely achieved by biological nanostructures, molecular sensing, and the fabrication of porous materials required for water purification and molecular separations.

Oxygen responsive sensor platforms were fabricated by pin printing tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II) ([Ru(dpp)(3)](2+)) doped sols onto wavelength tuned reflective Bragg gratings. In an epi-luminescence configuration, these Bragg gratings (Gr) were designed to selectively reflect the O(2) responsive [Ru(dpp)(3)](2+) emission toward the detector to enhance the detected signal magnitude. The xerogel based sensors were formed onto (i) glass (XGl), (ii) directly on top of the grating (XGrGl), or (iii) on the glass substrate opposite the grating (XGlGr). The results show that all sensors exhibit linear, statistically equivalent O(2) sensitivities, and the XGrGl platform yields up to an 8-fold increase in relative detected analytical signal (RDAS) in comparison to the control (XGl) platform., (© 2011 American Chemical Society)

Four-component xerogel films consisting of 1 mole-% n-octadecyltrimethoxysilane (C18) and 50 mole-% tetraethoxysilane (TEOS) in combination with 1-24 mole-% tridecafluoro-1,1,2,2-tetrahydrooctyltriethoxysilane (TDF) and 25-48 mole-% n-octyltriethoxysilane (C8) and a 1:49:50 mole-% C18/TDF/TEOS were prepared. Settlement of barnacle cyprids and removal of juvenile barnacles, settlement of zoospores of the alga Ulva linza, and strength of attachment of 7-day sporelings (young plants) of Ulva were compared amongst the xerogel formulations. Several of the xerogel formulations were comparable to poly(dimethylsiloxane) elastomer with respect to removal of juvenile barnacles and removal of sporeling biomass. The 1:4:45:50 and 1:14:35:50 C18/TDF/C8/TEOS xerogels displayed some phase segregation by atomic force microscopy (AFM) pre- and post-immersion in water. Imaging reflectance infrared microscopy showed the formation of islands of alkane-rich and perfluoroalkane-rich regions in these same xerogels both pre- and post-immersion in water. Surface energies were unchanged upon immersion in water for 48 h amongst the TDF-containing xerogel coatings. AFM measurements demonstrated that surface roughness on the 1:4:45:50 and 1:14:35:50 C18/TDF/C8/TEOS xerogel coatings decreased upon immersion in water.

Five non-biocidal xerogel coatings were compared to two commercial non-biocidal coatings and a silicone standard with respect to antifouling (AF)/fouling-release (FR) characteristics. The formation and release of biofilm of the marine bacterium Cellulophaga lytica, the attachment and release of the microalga Navicula incerta, and the fraction removal and critical removal stress of reattached adult barnacles of Amphibalanus amphitrite were evaluated in laboratory assays. Correlations of AF/FR performance with surface characteristics such as wettability, surface energy, elastic modulus, and surface roughness were examined. Several of the xerogel coating compositions performed well against both microfouling organisms while the commercial coatings performed less well toward the removal of microalgae. Reattached barnacle adhesion as measured by critical removal stress was significantly lower on the commercial coatings when compared to the xerogel coatings. However, two xerogel compositions showed release of 89-100% of reattached barnacles. These two formulations were also tested in the field and showed similar results.

Important interfacial processes in disciplines ranging from medicine to the separations sciences occur over a wide range of pressures, temperatures, and time scales. In this paper we report a new high-pressure total internal reflection fluorescence (HP-TIRF) apparatus that allows rapid fluorescence measurements of sub-monolayers in contact with liquids and supercritical fluids between 293 K and 353 K and up to 250 bar with picosecond time resolution. We use the HP-TIRF system to study the in-plane rotational reorientation dynamics of the fluorescent probe BODIPY 494/503 (C(2v) symmetry) covalently attached to silica surfaces that have been silanized with n-propyltrimethoxysilane (C(3)-TMOS) or 3,3,3-trifluoropropyltrimethoxysilane (CF(3)-TMOS) when the interface is subjected to pure supercritical carbon dioxide (scCO(2)). The in-plane BODIPY 494/503 rotational reorientation dynamics are assessed by using the Debye-Stokes-Einstein expression. As the scCO(2) density increases the local microviscosity surrounding the tethered BODIPY 494/503 molecule decreases. The terminal group (CH(3) versus CF(3)) within the silane monolayer governs the onset and absolute magnitude of the observed viscosity changes. The results are explained in terms of the wellknown solubility of fluorine-containing species in scCO(2).

We describe a compact luminescent gaseous oxygen (O 2 ) sensor microsystem based on the direct integration of sensor elements with a polymeric optical filter and placed on a low power complementary metal-oxide semiconductor (CMOS) imager integrated circuit (IC). The sensor operates on the measurement of excited-state emission intensity of O 2 -sensitive luminophore molecules tris(4,7-diphenyl-1,10-phenanthroline) ruthenium(II) ([Ru(dpp) 3 ] 2+ ) encapsulated within sol-gel derived xerogel thin films. The polymeric optical filter is made with polydimethylsiloxane (PDMS) that is mixed with a dye (Sudan-II). The PDMS membrane surface is molded to incorporate arrays of trapezoidal microstructures that serve to focus the optical sensor signals on to the imager pixels. The molded PDMS membrane is then attached with the PDMS color filter. The xerogel sensor arrays are contact printed on top of the PDMS trapezoidal lens-like microstructures. The CMOS imager uses a 32 × 32 (1024 elements) array of active pixel sensors and each pixel includes a high-gain phototransistor to convert the detected optical signals into electrical currents. Correlated double sampling circuit, pixel address, digital control and signal integration circuits are also implemented on-chip. The CMOS imager data is read out as a serial coded signal. The CMOS imager consumes a static power of 320 µW and an average dynamic power of 625 µW when operating at 100 Hz sampling frequency and 1.8 V DC. This CMOS sensor system provides a useful platform for the development of miniaturized optical chemical gas sensors.

Background: Cellular retinol binding-protein I (CRBPI) and cellular retinol binding-protein II (CRBPII) serve as intracellular retinoid chaperones that bind retinol and retinal with high affinity and facilitate substrate delivery to select enzymes that catalyze retinoic acid (RA) and retinyl ester biosynthesis. Recently, 9-cis-RA has been identified in vivo in the pancreas, where it contributes to regulating glucose-stimulated insulin secretion. In vitro, 9-cis-RA activates RXR (retinoid × receptors), which serve as therapeutic targets for treating cancer and metabolic diseases. Binding affinities and structure-function relationships have been well characterized for CRBPI and CRBPII with all-trans-retinoids, but not for 9-cis-retinoids. This study extended current knowledge by establishing binding affinities for CRBPI and CRBPII with 9-cis-retinoids., Methods: We have determined apparent dissociation constants, K'(d), through monitoring binding of 9-cis-retinol, 9-cis-retinal, and 9-cis-RA with CRBPI and CRBPII by fluorescence spectroscopy, and analyzing the data with non-linear regression. We compared these data to the data we obtained for all-trans- and 13-cis-retinoids under identical conditions., Results: CRBPI and CRBPII, respectively, bind 9-cis-retinol (K'(d), 11nM and 68nM) and 9-cis-retinal (K'(d), 8nM and 5nM) with high affinity. No significant 9-cis-RA binding was observed with CRBPI or CRBPII., Conclusions: CRBPI and CRBPII bind 9-cis-retinol and 9-cis-retinal with high affinities, albeit with affinities somewhat lower than for all-trans-retinol and all-trans-retinal., General Significance: These data provide further insight into structure-binding relationships of cellular retinol binding-proteins and are consistent with a model of 9-cis-RA biosynthesis that involves chaperoned delivery of 9-cis-retinoids to enzymes that recognize retinoid binding-proteins., (Copyright © 2011. Published by Elsevier B.V.)

We report on the founding member of a unique class of luminescent ionic liquids integrating a photoacidic anion that responds to the presence of both condensed- and gas-phase basicity; the analytical response is ratiometric in nature, visible to the naked eye, and offers fascinating prospects in smart photofluids, liquid logic gates, electronic noses, and sensory inks., (© The Royal Society of Chemistry 2011)

In this paper, we study the effect of temperature on the operation and performance of a xerogel-based sensor microarrays coupled to a complementary metal-oxide semiconductor (CMOS) imager integrated circuit (IC) that images the photoluminescence response from the sensor microarray. The CMOS imager uses a 32 × 32 (1024 elements) array of active pixel sensors and each pixel includes a high-gain phototransistor to convert the detected optical signals into electrical currents. A correlated double sampling circuit and pixel address/digital control/signal integration circuit are also implemented on-chip. The CMOS imager data are read out as a serial coded signal. The sensor system uses a light-emitting diode to excite target analyte responsive organometallic luminophores doped within discrete xerogel-based sensor elements. As a proto type, we developed a 3 × 3 (9 elements) array of oxygen (O2) sensors. Each group of three sensor elements in the array (arranged in a column) is designed to provide a different and specific sensitivity to the target gaseous O2 concentration. This property of multiple sensitivities is achieved by using a mix of two O2 sensitive luminophores in each pin-printed xerogel sensor element. The CMOS imager is designed to be low noise and consumes a static power of 320.4 μW and an average dynamic power of 624.6 μW when operating at 100-Hz sampling frequency and 1.8-V dc power supply.

A fluorescence energy transfer "de-quenching" assay was implemented to follow the equilibrium unfolding behaviour of site-specific tetramethylrhodamine-labelled yeast cytochrome c in aqueous ionic liquid solutions; additionally, this approach offers the prospect of naked eye screening for biocompatible ion combinations in hydrated ionic liquids.

The creation of tetracycline (TC) responsive molecularly imprinted xerogels (MIXs) was investigated using electronic absorbance, liquid chromatography-ion-trap mass spectrometry (LC-ITMS), and first-principles theory. Experimental results show that the template molecule converts to its epimer, 4-epitetracycline (ETC), during the imprinting process. Additionally, end capping of the MIX surface silanols transforms TC into anhydrotetracycline (ATC) and 4-epianhydrotetracycline (EATC). Hence, despite aiming to imprint for a single analyte (TC), one simultaneously imprints for up to four analogs (TC, ETC, EATC and ATC) within a MIX. Binding studies using LC-MS showed the binding of the prepared xerogels with the four analogs. In some formulations, preferential uptake of ETC, EATC and ATC relative to the template molecule (TC) was observed. Computations of the interaction energies between silane monomers and the four analogs reveal that ETC, EATC and ATC have higher interaction energies and are more likely to be imprinted in comparison to TC.

Mixtures of n-octadecyltrimethoxysilane (C18, 1-5 mole-%), n-octyltriethoxysilane (C8) and tetraethoxysilane (TEOS) gave xerogel surfaces of varying topography. The 1:49:50 C18/C8/TEOS xerogel formed 100-400-nm-wide, 2-7-nm deep pores by AFM while coatings with ≥3% C18 were free of such features. Segregation of the coating into alkane-rich and alkane-deficient regions in the 1:49:50 C18/C8/TEOS xerogel was observed by IR microscopy. Immersion in ASW for 48 h gave no statistical difference in surface energy for the 1:49:50 C18/C8/TEOS xerogel and a significant increase for the 50:50 C8/TEOS xerogel. Settlement of barnacle cyprids and removal of juvenile barnacles, settlement of zoospores of the alga Ulva linza, and strength of attachment of 7-day sporelings were compared amongst the xerogel formulations. Settlement of barnacle cyprids was significantly lower in comparison to glass and polystyrene standards. The 1:49:50 and 3:47:50 C18/C8/TEOS xerogels were comparable to PDMSE with respect to removal of juvenile barnacles and sporeling biomass, respectively.

A series of silica-based tetracycline (TC)-imprinted xerogel sorbents were prepared by sol-gel processing and were characterized for TC binding. Molecularly imprinted xerogels (MIXs) formed from allyltriethoxysilane (AtEOS) and tetraethoxysilane (TEOS) and end capped with trimethylchlorosilane exhibited the best analytical performance (imprinting factor, IF, of 7.46±0.13). Computational modeling was used to estimate the interaction energy (IE) between TC and each type of silane to evaluate our ability to predict the analytical performance of a given MIX. Rankings from the computations agreed with the experimental data showing the AtEOS having the highest IE in comparison to the other formulations. Together, these results demonstrate the potential and limitations of using theoretical calculations to guide the development of analyte selective MIXs in comparison to arbitrary trial and error approaches traditionally used to produce MIXs as sorbents for solid phase extraction., (Copyright © 2010 Elsevier B.V. All rights reserved.)

We describe a Complementary Metal-Oxide Semiconductor (CMOS) Direct Time Interval Measurement (DTIM) Integrated Circuit (IC) to detect the decay (fall) time of the luminescence emission when analyte-sensitive luminophores are excited with an optical pulse. The CMOS DTIM IC includes 14 × 14 phototransistor array, transimpedance amplifier, regulated gain amplifier, fall time detector, and time-to-digital convertor. We examined the DTIM system to measure the emission lifetime of oxygen-sensitive luminophores tris(4,7-diphenyl-1, 10-phenanthroline) ruthenium(II) ([Ru(dpp)(3)](2+)) encapsulated in sol-gel derived xerogel thin-films. The DTIM system fabricated using TSMC 0.35 μm process functions to detect lifetimes from 4 μs to 14.4 μs but can be tuned to detect longer lifetimes. The system provides 8-bit digital output proportional to lifetimes and consumes 4.5 mW of power with 3.3 V DC supply. The CMOS system provides a useful platform for the development of reliable, robust, and miniaturized optical chemical sensors.

We present the design and implementation of a luminescence-based miniaturized multisensor system using pin-printed xerogel materials which act as host media for chemical recognition elements. We developed a CMOS imager integrated circuit (IC) to image the luminescence response of the xerogel-based sensor array. The imager IC uses a 26 × 20 (520 elements) array of active pixel sensors and each active pixel includes a high-gain phototransistor to convert the detected optical signals into electrical currents. The imager includes a correlated double sampling circuit and pixel address/digital control circuit; the image data is read-out as coded serial signal. The sensor system uses a light-emitting diode (LED) to excite the target analyte responsive luminophores doped within discrete xerogel-based sensor elements. As a prototype, we developed a 4 × 4 (16 elements) array of oxygen (O 2 ) sensors. Each group of 4 sensor elements in the array (arranged in a row) is designed to provide a different and specific sensitivity to the target gaseous O 2 concentration. This property of multiple sensitivities is achieved by using a strategic mix of two oxygen sensitive luminophores ([Ru(dpp) 3 ] 2+ and ([Ru(bpy) 3 ] 2+ ) in each pin-printed xerogel sensor element. The CMOS imager consumes an average power of 8 mW operating at 1 kHz sampling frequency driven at 5 V. The developed prototype system demonstrates a low cost and miniaturized luminescence multisensor system.