Search

Objective: To describe sacroiliac luxation stabilization in cats using two screws and to report clinical and radiographic short-term outcomes., Study Design: Retrospective clinical cohort study., Sample Population: Cats (n = 67) with sacroiliac luxation., Methods: Case records of cats presented for sacroiliac luxation stabilized using two screws per side affected, one lag and one positional, between 2014 and 2023 were reviewed. The percentage of sacral purchase (PoSP) for each screw, percentage of reduction (PoR), and pelvic canal width ratio (PCWR) were measured and calculated., Results: Eighty-two sacroiliac luxations were stabilized. Two 2.0 mm screws were used in 69 cases; two 2.4-mm screws in nine cases, and one 2.4 mm with one 2.0 mm screw in four cases. The mean PoSPs for lag and positional screws were 46% ± 12 and 31% ± 11, respectively. The median PoR was 89% (41 to 100). The mean PCWR was 1.23 ± 0.11. Clinical follow up was available for 42 cats with 53 sacroiliac luxations at a median of 87 days (36 to 2503). The full function was noted in 34 patients (81%). Screw failure occurred in five sacroiliac joints (4.7%), including loosening (n = 3), and breakage (n = 2) of the positional screws (n = 1). Pelvic canal diameter was maintained in all cases., Conclusion: Excellent functional and radiographic outcomes were obtained for cats with sacroiliac luxation stabilized with two sacroiliac screws., Clinical Significance: Feline sacroiliac luxation can be stabilized using two sacroiliac screws., (© 2024 American College of Veterinary Surgeons.)

Objective:  The aim of this study was to measure the mechanical properties and failure mode of an ex vivo model of proximal interphalangeal arthrodesis in horses with different methods of proximal screw fixation using a locking compression plate., Study Design:  Pastern joint arthrodesis with a 3-hole 4.5-mm narrow locking compression plate was performed on 20 forelimbs of equine cadavers, randomized into four groups based on the fixation method and type of proximal screw used: unicortical cortex, bicortical cortex, unicortical locking, bicortical locking. Single-cycle axial compression testing was conducted until failure. The frequency of implant plastic deformation was recorded. Bone failure analysis was performed through computed tomography examinations and fractal analysis., Results:  There were no differences in the analysed mechanical variables and fractal dimension among the groups. Transarticular screws showed a higher frequency of deformation (75%) regardless of the group. Both unicortical locking and bicortical locking groups deformed the plate more frequently., Conclusion:  The type of screw used in the proximal hole of the locking compression plate and its method of anchoring in the proximal phalanx do not affect the mechanical properties of pastern arthrodesis in equine cadavers subjected to single-cycle axial compression tests until failure., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective:  The main aim of this pilot study was to assess the feasibility of spinal neuronavigation for plate fixation of lumbar vertebrae in miniature breed dogs using a surgical navigation system in combination with a custom-made reference array., Study Design:  This was an experimental cadaveric study in five miniature breed dogs., Methods:  A 4-hole locking plate with four 2.0-mm locking screws was placed on two adjacent lumbar vertebrae using a neuronavigation system consisting of a mobile cone beam computed tomography linked to a navigation system. The procedure was performed by a novice surgeon. The plate and screw positions were assessed for surgical safety using predefined criteria. Surgical accuracy was determined by the deviation of entry and exit points between pre- and postoperative images., Results:  A total of five plates and 20 screws were placed. In 85% (17/20), screws were placed appropriately. The median entry point deviation was 1.8 mm (range: 0.3-3.7) and the median exit point deviation was 1.6 mm (range: 0.6-5)., Conclusion:  Achievement of surgical accuracy in the placement of screws for fixation of lumbar vertebral plates in small breed dogs using neuronavigation with a custom-made reference array by a novice surgeon resulted in surgical safe plate placement in four of the five cadavers. Therefore, we judge the method as promising, however, further studies are necessary to allow the transfer of image-guided navigation for lumbar plate fixation into the clinic., Competing Interests: None declared., (Thieme. All rights reserved.)

Objectives: The aim of this study was to assess the efficacy of pelvic osteotomy and ventral fixation of the ischium using cortical screws and polymethylmethacrylate (PMMA) for feline pelvic canal stenosis (PCS) associated with malunion after conservative management of pelvic fractures., Methods: Surgical pelvic enlargement was performed for PCS in six cats. The medical records, including information on the patients, surgical procedures, defecation and complications, were reviewed. The sacral index (SI) and colonic:lumbar:vertebral ratio (CLVR) were evaluated based on pre- and postoperative radiographs., Results: This study included five castrated male cats and one spayed female cat. Postoperative improvements in constipation and defecatory difficulty were noted in all cases. The postoperative SI was significantly higher (mean 0.93, range 0.72-1.13) than the preoperative SI (mean 0.59, range 0.45-0.74) ( P <0.001). However, no statistically significant change was found in the CLVR preoperatively and up to 3 months postoperatively. A successful union of the ilium was observed, without implant failures. One case developed necrosis of the pubic surgical wound., Conclusions and Relevance: This study indicated the potential benefits of pelvic osteotomy and ventral fixation of the pelvic floor using screws and PMMA for achieving pelvic cavity enlargement in treating feline PCS associated with defecatory problems., Competing Interests: Conflict of interestHF is employed by Platon Japan, Tokyo, Japan, the manufacturer of crank plates and screws used in this study. The authors declared that there were no other conflicts of interest.

Objective: To biomechanically evaluate the stability of internal fixation methods for femoral neck fractures in small-breed dogs. Furthermore, the possibility of replacing the headed screw with fully threaded headless cannulated screws in the fixation method was assessed., Methods: The study was conducted from December 12, 2023, to February 7, 2024. A total of 18 femurs from 9 canine cadavers were used in this study. After a simple neck fracture was created, in group A (n = 6), the fracture was stabilized with three 1.1-mm parallel Kirschner wires (K-wires). In group B (n = 6), a 3.0-mm partially threaded cannulated screw and an antirotation pin were used. In group C (n = 6), a 2.5-mm fully threaded headless cannulated screw and an antirotation pin were used. A mechanical test was conducted to apply a single axial compressive load to the femoral head., Results: 9 adult small-breed dogs weighing 3.6 to 8.3 kg (mean ± SD; 5.9 ± 1.6). The mean maximum failure load was highest in group C (495 ± 81 N), followed by group B (454 ± 50.4 N), and then group A (222 ± 21.6 N). Significant differences in maximum failure load were observed between groups A and B as well as groups A and C but not between groups B and C., Conclusion: The use of fully threaded headless cannulated screws presents a promising method for internal fixation of canine femoral neck fractures., Clinical Relevance: To demonstrate the potential stability and reliability of fully threaded headless cannulated screws.

Objective: To assess the feasibility of a novel transcoronal approach for the treatment of axial type 3 cysts of the palmar/plantar aspect of the distal phalanx (P3)., Study Design: Ex vivo, experimental study., Sample Population: Ten cadaveric specimens, four forelimbs and six hindlimbs., Methods: All cadaveric specimens underwent radiographically guided drilling, followed by cortical screw placement. The cartilage was macroscopically assessed after disarticulation of the distal interphalangeal joint. The entry point and trajectory were evaluated with computed tomography. Results were categorized as: axial, near-axial and abaxial. The minimal distance from the outer margin of the drill hole and the proximal border of the subchondral bone plate was measured using frontal computed tomographic slices., Results: Eight of the 10 screws were in an axial to near-axial position and nine followed the desired axial to near-axial trajectory. One screw was inserted axially but continued in an abaxial trajectory. Iatrogenic damage to the joint cartilage, flexor cortex and solar canal of P3 was not observed. All cortical screws were placed close to the proximal subchondral bone-plate of P3., Conclusion: The desired axial/near-axial drilling and screw placement, under radiographic guidance, was achieved in nine out of 10 specimens., Clinical Significance: This novel technique seems promising for the treatment of inaccessible P3 cysts. Additional studies are required to investigate its feasibility in clinical cases, and the long-term outcome following transcystic screw placement of type 3 P3 cysts., (© 2024 American College of Veterinary Surgeons.)

Objective: Medical records for dogs treated with tibial plateau leveling osteotomy (TPLO) using Arthrex 3.5 mm self-tapping screws (STS) were evaluated to determine the incidence rate of transcortical tibial fractures (TCTF) and development of complications., Study Design: Retrospective case report., Study Population: A total of 78 dogs., Methods: Dogs that underwent a TPLO performed from March 2022 to August 2023 were reviewed. Postoperative TPLO radiographs were examined for evidence of a TCTF with Arthrex 3.5 mm STS. Records were reviewed for complications up to 14 weeks after surgery., Results: Evidence of a TCTF was found in 42% of cases (33 of 78) and 14% (36 of 250) of STS screws distal to the osteotomy. TCTFs were only identified distal to the osteotomy. Three dogs had radiographic evidence of more than one TCTF. Of the dogs with radiographic TCTF, 6% of patients (2 of 33) developed a major complication that required surgical stabilization of a tibial fracture associated with screw angulation relative to the plate., Conclusion: Use of Arthrex 3.5 mm STS for TPLO is associated with risk of TCTF. TCTF can compromise the structural properties of the tibia and cause complete tibial fracture requiring major revision surgery., Clinical Significance: Development of TCTF after use of STS for TPLO has been recognized, in contrast to use of non-self-tapping screws, and was considered a benign complication. Our findings suggest TCTF associated with Arthrex 3.5 mm STS use in TPLO can contribute to major complications after surgery, including complete tibial fracture, particularly if screws are not placed perpendicular to the plate., (© 2024 The Author(s). Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Objective: To report the surgical approaches and stabilization of lateral and medial tibial plateau fractures (TPF), as well as the long-term outcome following repair., Study Design: Prospective series of three client-owned dogs., Animals: Three dogs., Methods: For the two lateral TPF cases (Unger type 41-B1), the surgical approach included separation of the lateral collateral ligament and long digital extensor tendon. The lateral meniscus was elevated to allow visualization of the tibial surface and assess fracture reduction. The first case was repaired using two 2.0 mm lag screws (with washers). The second case sustained a lateral TPF, fibular fracture and concurrent tubercle of Gerdy fracture. Both tibial fractures were stabilized using two 2.0 mm lag screws with washers and two 0.9 mm Kirschner wires (K-wires). A third case, diagnosed with an Unger type 41-B2 medial TPF, was treated using 0.9 mm K-wires and 22-gauge tension band., Results: There were no major complications noted. One minor complication occurred (screw yield two weeks postoperatively). By 8 weeks, all patients reached clinical union with good limb function. Owners were contacted 9-36 months postoperatively. LOAD scores and examinations were performed for two of three patients; the third patient was not contactable after relocating out of state. Both cases with completed questionnaires had a LOAD score of 5/52., Conclusion: Tibial plateau fractures are rare in canine patients. While challenging, they can be successfully managed using a combination of lag screws, K-wires, and tension band., Clinical Significance: Surgical stabilization of TPF is feasible and may reduce the risk of meniscal injury., (© 2024 The Authors. Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Objective:  The aim of this study was to report postoperative complications and long-term outcomes following transcondylar screw placement for humeral intracondylar fissure (HIF)., Study Design:  It was a retrospective single-centre case series. Medical records (2018-2022) were reviewed for dogs with HIF treated with transcondylar screw placement. Data collected included signalment, concurrent orthopaedic disease, partial or complete HIF, surgeon, surgical approach, surgical technique and implant type, transcondylar screw angulation, postoperative complications and outcomes. Long-term outcome was assessed with owner questionnaire, orthopaedic examination and follow-up radiography. Statistical analysis was performed to identify risk factors predisposing to a complication or a poor outcome., Results:  Forty-seven dogs (57 elbows) met the inclusion criteria; long-term follow-up was available in 41 dogs (50 elbows). Minor and major medical complications were noted in seven and three elbows respectively. The total complication rate was 17.5%. Increasing age was significantly associated with a reduced risk of postoperative complications ( p  = 0.0051). No other risk factors were identified. A postoperative complication was not associated with a less than full outcome ( p  = 0.5698)., Conclusion:  Transcondylar screw placement for HIF is associated with a low complication rate and good outcome., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective:  The aim of this study was to compare stiffness and strain of an in vitro fracture-gap model secured with a primary 3.5-mm locking compression plate (LCP) at three primary plate working lengths without and with an orthogonal 2.7-mm LCP., Study Design:  Primary plate screw configurations modeled short working length (SWL), medium working length (MWL), and long working length (LWL) constructs. Construct stiffness with and without an orthogonal plate during nondestructive four-point bending and torsion, and plate surface strain measured during bending, was analyzed., Results:  Single plate construct stiffness was significantly, incrementally, lower in four-point bending and torsion as working length was extended. Addition of an orthogonal plate resulted in significantly higher bending stiffness for SWL, MWL, and LWL ( p  < 0.05) and torsional stiffness for MWL and LWL ( p  < 0.05). Single plate construct strain was significantly, incrementally, higher as working length was extended. Addition of an orthogonal plate significantly lowered strain for SWL, MWL, and LWL constructs ( p  < 0.01)., Conclusion:  Orthogonal plate application resulted in higher bending and torsional construct stiffness and lower strain over the primary plate in bending in this in vitro model. Working length had an inverse relationship with construct stiffness in bending and torsion and a direct relationship with strain. The inverse effect of working length on construct stiffness was completely mitigated by the application of an orthogonal plate in bending and modified in torsion., Competing Interests: None declared., (Thieme. All rights reserved.)

Objectives:  The first objective of this study was to compare the mechanical performance of a straight and contoured rod for the sliding on pivot-locking clamp (SOP-LC) system. The second objective was to compare single-cycle bending and torsion of the SOP-LC rod-bone constructs to a bone gap model between two clamp configurations., Study Design:  First experiment, 5 mm diameter rods from the 3.5 mm SOP-LC system, 4 straight and 4 bent rods were mechanically compared in four-point bending. The second experiment, 8 constructs with clamps on a single side of the rod and 8 constructs with clamps on alternating sides were compared in four-point bending and torsion. A torque limiting screwdriver at 2.5N was used for all constructs., Results:  There were not significant differences between the noncontoured versus contoured rods. Constructs with clamps on a single side had a significantly higher yield load, yield displacement and bending strength, but the constructs with alternating clamps had a significantly higher initial torsional stiffness. There were no other significant differences. Mild clamp slippage and mild screw bending were noted in all the torsion tested constructs graphically with multiple stiffness slopes and visually on the post-tested constructs., Conclusion:  Torque applied to initial screw placement may play a role in reducing clamp slippage. Although bending yield load, bending yield displacement, bending strength and torsional stiffness were improved by different clamp placement, clinically this will depend on fracture type. Further studies are needed for clinical significance., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective: To assess the fatigue and load-to-failure mechanical characteristics of an intramedullary nail with a threaded interference design (TID) in comparison to a commercially available veterinary angle-stable nail with a Morse taper bolt design (I-Loc) of an equivalent size., Methods: 10 single interlocking screw/bolt constructs of TID and I-Loc implants were assembled using steel pipe segments and placed through 50,000 cycles of simulated, physiologic axial or torsional loading. Entry torque, postfatigue extraction torque, and 10th, 25,000th, and 50,000th cycle torsional toggle were assessed. Each construct was then loaded to failure in the same respective direction as fatigue testing. Four complete constructs of each design were then assessed using a synthetic bone analog with a 50-mm central defect via nondestructive torsional and axial loading followed by axial load to failure., Results: All constructs were angle stable at all time points and withstood fatigue loading. Median insertional torque, extraction torque-to-insertion torque ratio, and torsional yield load were 33%, 33%, and 72.5% lower, respectively, for the TID interlocking screws. No differences in torsional peak load, torsional stiffness, axial yield load, axial stiffness, or axial peak load were identified. No differences in complete construct angle stability, torsional stiffness, axial peak load, axial stiffness, or axial yield load were identified., Clinical Relevance: The TID had an inferior torsional yield load when compared to I-Loc implants but generated angle stability and sustained simulated physiologic fatigue loading. The TID may be a suitable mechanism for generating angle stability in interlocking nails.

This report describes a centralisation procedure for the treatment of a radial non-union, characterised by extensive bone loss and an intact ulna, in an 18-month-old toy poodle. A lateral approach to the radius/ulna shafts was realised and, after debridement of the non-union site, an ulnar osteotomy was performed proximal to the styloid process of the ulna. Transposition of the distal fragment of the radius to the distal end of the osteotomised proximal segment of the ulna was performed and the stabilisation was obtained using a locking plate with proximal screws in the ulnar shaft and distal screws in the radius epiphysis. The patient achieved bone union in 10 weeks and the last evaluation, performed 112 weeks postoperatively, showed a full return to pre-injury function. Based on the results of this report, the centralisation was effective in the treatment of post-traumatic absence of the radial shaft in a dog., (© 2024 British Small Animal Veterinary Association.)

Objective: To describe fluoroscopically-assisted closed reduction and percutaneous fixation of sacroiliac-luxation (SIL) in cats and report radiographic results and long-term functional outcomes., Study Design: Retrospective clinical study., Animals: Eleven cats., Methods: Percutaneous fixation of 17 SILs in 11 cats was performed with 2.4 mm headless cannulated compression screws under fluoroscopic guidance. Luxation-reduction, screw placement and purchase within the sacral body, pelvic canal diameter ratio (PCDR) and hemipelvic canal width ratio (HCWR) were assessed on pre- and postoperative radiographs. Radiographic follow-up was performed to assess the same parameters when available. Long-term clinical outcome was evaluated with an owner questionnaire. Wilcoxon paired-test was performed for comparison., Results: Mean age and bodyweight of the cats were 3.3 ± 2.6 years and 4.0 ± 0.82 kg, respectively. Nine cats presented with concurrent pelvic injuries. Median luxation-reduction was 94.1% (IQR = 13.9) and median screw-purchase within the sacral body was 73.3% (IQR = 17.0) immediately postoperatively. One screw exited the sacral body caudally. Upon 7-week radiographic follow-up, luxation-reduction (88.3%, IQR = 20.1) and screw-purchase (70.7%, IQR = 12.8) had decreased compared to immediately postoperatively (p = .008 and p = .013 respectively). Screw migration was not observed. PCDR and HCWR measured on postoperative radiographs indicated successful restoration of the pelvic canal width. Owners reported an excellent long-term functional outcome (mean postoperative time: 19 ± 5 months)., Conclusion: Fluoroscopically-assisted closed reduction and fixation of feline SIL using 2.4 mm headless cannulated compression screws allowed good reduction and optimal screw purchase within the sacral body. An excellent functional outcome was reported., Clinical Significance: Minimally invasive reduction and fixation with headless compression screws should be considered in cats with SIL., (© 2024 The Authors. Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Objective: To determine the influence of screw configuration on the reduction and stabilization of simulated complete lateral condylar fracture., Study Design: Randomized experimental crossover study., Methods: A lateral condylar fracture was simulated in 18 cadaver limbs from nine horses. Each limb underwent repair with 4.5 mm diameter cortex screws, tightened to 4 Nm, in a linear and triangular configuration. Computed tomography (CT) of each repair was performed with the limbs in unloaded and loaded conditions. Fracture gaps were measured at the dorsal, palmar, and middle locations of the third metacarpal condyle. Fracture gap measurements were graded 0-4, based on voxels. Following descriptive analysis, a Bayesian network (BN) model was fitted to the data., Results: The median fracture grade was 0 (range: 0-4) for unloaded linear repairs and 2 (0-4) for loaded linear repairs. The median fracture grade was 0 (0-3) for unloaded triangular repairs and 1 (0-3) for loaded triangular repairs. Bayesian network sensitivity analysis showed that the construct configuration reduced the uncertainty in the measured fracture outcome by 0.8%., Conclusion: Triangular screw configuration resulted in better fracture reduction and stability in comparison with linear screw configuration. However, the BN sensitivity analysis results showed that the effect of construct configuration on fracture outcome was weak., Clinical Significance: These findings indicate a low probability that triangular repair of lateral condylar fracture will result in improved outcomes, when compared with linear repair., (© 2024 The Authors. Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Background: The study employs finite element analysis to investigate stress distribution in the radius of toy poodles after screw removal. The examination focuses on the biomechanical implications of varied screw hole configurations using 1.5 and 2.0-mm locking compression plates (LCPs) with notched head T-Plates., Aim: To provide a noninvasive approach to analyzing the immediate consequences of screw removal from the radius bone in toy poodles. Specifically, it explores the impact of varied plate designs and screw arrangements on stress distribution within the forelimb bones., Methods: The study constructs a three-dimensional bone model of the toy poodle's forelimb based on computed tomography (CT) images. Simulations were designed to replicate jumping and landing from a 40 cm height, comparing stress distribution in the radius post-screw removal., Results: The analysis reveals significant variations in stress distribution patterns between the two LCPs. The radius implanted with the 2.0-mm LCP displays a uniform stress distribution, contrasting with the 1.5-mm plates. Localized stress concentration is observed around the screw holes, while trabecular bone regions near the screw holes exhibit lower stress levels., Conclusion: The study highlights the plate designs and screw configurations that affect bone stress in toy poodle forelimbs post-screw removal. The findings provide valuable insights for veterinarians, aiding informed decisions in veterinary orthopedic practices., Competing Interests: The authors declare that there is no conflict of interest.

Objective: To determine the influence of screw direction on complications following transcondylar screw placement for the treatment of canine humeral intracondylar fissures (HIFs)., Study Design: Equivalence, parallel group, randomized clinical trial., Sample Population: Fifty-two client owned dogs (73 elbows)., Methods: Transcondylar screw placement was randomized to either a medial or lateral approach. The primary outcome was the incidence of postoperative complications., Results: There were 37 cases in the lateral approach group and 36 cases in the medial approach group. There was a significantly greater proportion of postoperative complications following placement of transcondylar screws from a lateral to medial direction (p = .001). There were seven cases with complications (19%) in the medial approach group versus 23 cases with complications (62%) in the lateral approach group. The majority of complications were seromas (n = 13) and surgical site infections (n = 16) with 4 complications requiring further surgery. Implant area moment of inertia (AMI), normalized to bodyweight, was lower in dogs with a major complication (p = .037)., Conclusion: Transcondylar screws placed from lateral to medial for canine HIFs had a greater proportion of postoperative complications in this randomized clinical trial design. Implants with a lower AMI, relative to bodyweight, were more likely to lead to major complications., Clinical Significance: We recommend placing transcondylar screws from medial to lateral for canine HIFs to reduce the risk of postoperative complications. Relatively small diameter implants had an increased risk of major complications., (© 2023 American College of Veterinary Surgeons.)

Objective: To describe an arthroscopically guided technique for lag screw placement across subchondral bone cyst (SBC) in the medial femoral condyle (MFC) and to compare postoperative racing performance with corticosteroid injection and cyst debridement., Study Design: Retrospective cohort study., Animals: One hundred twenty-three horses with 134 MFC SBCs undergoing treatment at a single referral hospital in the UK between January, 2009, and December, 2020., Methods: Sex, age, limb affected, radiographic cyst dimensions, preoperative and postoperative lameness, surgical technique (lag screw placement, cyst debridement, intralesional corticosteroid injection), and, where applicable, screw positioning were recorded retrospectively. A ratio was calculated using measurements from preoperative and postoperative radiographs. Outcome was assessed by resolution or improvement in lameness, reduction in cyst size, and starting one race after treatment. Outcome data was compared between treatment groups., Results: Twenty-six of 45 (57.8%) horses that underwent transcondylar screw placement raced postoperatively, at a median of 403 days between surgery and first postoperative race. There was no difference between treatment groups with regard to racing or preoperative and postoperative lameness. Cysts treated with transcondylar screw placement had a greater reduction in cyst size and a reduced period of convalescence in comparison with those that underwent debridement; the results were similar to those treated by intralesional corticosteroid injection., Conclusion: Postoperative racing rates were similar for all techniques. Convalescence was reduced for lag screw placement and corticosteroid injection compared to debridement., Clinical Significance: The arthroscopically guided technique results in radiographically consistent screw placement and cyst engagement and offers a viable alternative to other treatments., (© 2023 American College of Veterinary Surgeons.)

Objective:  The aim of this study was to evaluate the feasibility of safe positioning of double 2.3-mm headless cannulated self-compression screws (HCS) in a small dog cadaveric sacroiliac luxation model and to compare the static rotational biomechanical properties of fixation repaired using two different screw systems with a minimally invasive osteosynthesis technique: double 2.3-mm HCS and a single 3.5-mm standard cortical screw placed in a lag fashion., Study Design:  A unilateral small dog sacroiliac luxation model was stabilized using double 2.3-mm HCS ( n  = 11) or a single 3.5-mm cortical screw ( n  = 11). Radiographic and computed tomography (CT) imaging analyses and biomechanical testing of rotational force on the sacroiliac joint of both fixations were performed. The maximum load at failure and failure modes of each fixation were recorded and compared., Results:  Fluoroscopically guided percutaneous application of double HCS was safe in a unilateral sacroiliac luxation model in small dogs without violation of the vertebral and ventral sacral foramen. Furthermore, resistance to rotational force applied on fixation of the sacroiliac joint repaired with double 2.3-mm HCS estimated by maximum failure load was significantly higher than that of a single 3.5-mm cortical screw ( p  < 0.001)., Conclusion:  Although this was an experimental cadaveric study, based on our results, the use of smaller double HCS may be beneficial as an alternative to the conventional single lag screw for stabilization of sacroiliac luxation in small dogs., Competing Interests: None declared., (The Author(s). This is an open access article published by Thieme under the terms of the Creative Commons Attribution-NonDerivative-NonCommercial License, permitting copying and reproduction so long as the original work is given appropriate credit. Contents may not be used for commercial purposes, or adapted, remixed, transformed or built upon. (https://creativecommons.org/licenses/by-nc-nd/4.0/).)

Aim: To biomechanically compare the bending stiffness, strength, and cyclic fatigue of titanium additively manufactured (AM) and conventionally manufactured (CM) limited contact plates (LCP) of equivalent dimensions using plate-screw constructs., Methods: Twenty-four 1.5/2.0-mm plate constructs (CM: n = 12; AM: n = 12) were placed under 4-point bending conditions. Data were collected during quasi-static single cycle to failure and cyclic fatigue testing until implants plastically deformed or failed. Bending stiffness, bending structural stiffness, and bending strength were determined from load-displacement curves. Fatigue life was determined as number of cycles to failure. Median test variables for each method were compared using the Wilcoxon rank sum test within each group. Fatigue data was also analysed by the Kaplan-Meier estimator of survival function., Results: There was no evidence for a difference in bending stiffness and bending structural stiffness between AM and CM constructs. However, AM constructs exhibited greater bending strength (median 3.07 (min 3.0, max 3.4) Nm) under quasi-static 4-point bending than the CM constructs (median 2.57 (min 2.5, max 2.6) Nm, p = 0.006). Number of cycles to failure under dynamic 4-point bending was higher for the CM constructs (median 164,272 (min 73,557, max 250,000) cycles) than the AM constructs (median 18,704 (min 14,427, max 33,228) cycles; p = 0.02). Survival analysis showed that 50% of AM plates failed by 18,842 cycles, while 50% CM plates failed by 78,543 cycles., Conclusion and Clinical Relevance: Additively manufactured titanium implants, printed to replicate a conventional titanium orthopaedic plate, were more prone to failure in a shorter fatigue period despite being stronger in single cycle to failure. Patient-specific implants made using this process may be brittle and therefore not comparable to CM orthopaedic implants. Careful selection of their use on a case/patient-specific basis is recommended.

Objective:  An increased rate of surgical site infection (SSI) following treatment of canine humeral intracondylar fissure (HIF) with a lateromedially (LM) placed transcondylar screw (TCS) compared with a mediolateral (ML) TCS has been previously postulated. We hypothesized that the direction of insertion of the TCS would not affect the incidence of postoperative SSI., Study Design:  It was single-centre retrospective study. Dogs with HIF confirmed by computerized tomography, treated by TCS placement (between 2008 and 2019) and with a minimum follow-up of 12 weeks, were included. The following data were recorded: signalment, presenting clinical signs, direction of placement and size of the utilized TCS, surgical and anaesthetic times, concurrent surgical procedures, presence of concomitant elbow pathology, perioperative and postoperative antibiotic usage and postoperative complications. Recorded data were analysed with a multinomial logistic regression model with a p -value less than or equal to 0.05., Results:  Thirty-five dogs (46 elbows) met the inclusion criteria. Median clinical follow-up interval was 52 weeks. Seven of thirty-one elbows with a ML TCS, and 4/15 elbows with a LM TCS developed SSI. Four of nine dogs that underwent bilateral single-surgery TCS placement developed SSI unilaterally., Conclusion:  No significant difference was shown in short-term SSI occurrence between the ML and the LM direction of placement of the TCS., Competing Interests: None declared., (Thieme. All rights reserved.)

Objectives: To compare (1) performance of compact versus standard flute drill bits, (2) screw insertion properties and (3) pullout variables between interlocking thread (ITS) and buttress thread (BTS) self-tapping screws in third metacarpi., Study Design: In vitro experimental study., Sample Population: Paired third metacarpi from 11 Thoroughbreds aged 2-4 years., Methods: Screws were inserted into the lateral condylar fossae following bone preparation using the respective drill bit for each screw type. Screw pullout was achieved using a mechanical testing system. Density and porosity of bone surrounding screw holes was measured with microcomputed tomography following each pullout test. Drilling, screw insertion and pullout variables were compared between drill bit and screw types using repeated measures ANOVA. Linear regression analyses were used to characterize relationships between bone tissue properties and drill bit and screw outcomes., Results: Maximum torque power spectral density (PSD) was lower for compact flute drill bits. Insertion torque was 50% higher for ITS. BTS had 33% greater preyield stiffness and 7% greater mean yield force. Bone tissue properties affected measured variables similarly for both screw and drill bit types., Conclusions: Lower torque PSD may increase durability of the compact flute drill bit. ITS had greater insertional torque, which may reflect greater bone engagement. BTS had greater resistance to axial pullout forces., Clinical Significance: Metacarpal bone provides a simple model for comparison of drill bit and screw designs. Use of ITS to repair equine fractures subject to predominantly tensile forces is not justified based on the results of this study., (© 2023 The Authors. Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Objective: To report a surgical technique and outcomes of transiliosacral toggle suture repair to treat feline bilateral sacroiliac luxation/fracture (SILF)., Study Design: Retrospective study., Animals: Fifteen client-owned cats., Methods: The medical records of cats with bilateral SILF treated using a transiliosacral toggle suture repair were reviewed. Short- and medium-term outcomes were assessed through standard postoperative clinical evaluation and radiographs, including measurements of angle of deviation (AoD), percentage of reduction (PoR), and pelvic canal width ratio (PCWR). Long-term functional follow up was obtained from a questionnaire derived from the Feline Musculoskeletal Pain Index (FMPI)., Results: Fifteen cats were enrolled retrospectively, among which 13 survived to discharge. One minor wound complication, treated by secondary intention healing, was encountered. No major complication was reported. Immediately postoperatively, the mean absolute PoR values were 88.1 ± 11.2% and 91 ± 11.6% on the right and left side, respectively. The mean absolute AoD was 3.1 ± 2.8°, and the mean PCWR was 1.24 ± 0.08. The medium-term radiographic follow up at a median of 205 (71-682) days postsurgery revealed the good stability of the repair. Excellent functional outcomes were identified upon the analysis of 12 long-term questionnaires at a median of 365 (119-798) days postsurgery., Conclusion: Anatomic reduction was satisfactory and comparable with previously described techniques with good implant placement documented. Functional outcomes based on FMPI-derived questionnaires were good to excellent in our population., Clinical Significance: Transiliosacral toggle suture stabilization of bilateral SILF was associated with good outcomes in cats. Further studies are required to compare biomechanical properties and outcomes between this technique and previously described transiliosacral stabilization., (© 2023 The American College of Veterinary Surgeons.)

Objective:  The aim of this study was to compare the interfragmentary compressive force and area of compression generated by cortical screws inserted as either a lag screw or position screw in simulated lateral humeral condylar fractures., Study Design:   Ex vivo biomechanical study., Materials and Methods:  Thirteen pairs of cadaveric humeri from skeletally mature Merinos with simulated lateral humeral condylar fractures were used. Pressure sensitive film was inserted into the interfragmentary interface prior to fracture reduction with fragment forceps. A cortical screw was inserted as a lag screw or a position screw and tightened to 1.8Nm. Interfragmentary compression and area of compression were quantified and compared between the two treatments groups at three time points., Results:  After fracture reduction using fragment forceps (Time point 1: T1), there was no significant difference in interfragmentary compression and area of compression between the two treatments. A combination of fragment forceps and a cortical screw inserted as a lag screw (Time point 2: T2) produced significantly greater interfragmentary compression and area of compression compared with the same screw inserted as a positional screw. After removal of the fragment forceps, leaving only the cortical screw (Time point 3: T3), both the interfragmentary compression and area of compression remain significantly greater in the lag screw group., Conclusion:  Lag screws generate a greater force of compression and area of compression compared with position screws in this mature ovine humeral condylar fracture model., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective: To evaluate the ease and accuracy of using a 3-D printed (3-DP) drill guide to insert Kirschner wires through the ilium and into the sacral body in preparation for minimally invasive iliosacral screw placement in dog cadavers., Animals: 10 dog cadavers weighing 20 to 30 kg (mean ± SD, 24.5 ± 5 kg)., Methods: Kirschner wires were placed using a limited approach to the lateral ilium. Fluoroscopy was used in freehand and 3-DP drill guide application groups to facilitate the placement of a 1.0-mm Kirschner wire that was over-drilled using a 2.5-mm cannulated drill bit. Kirschner wires were placed using a 3-DP drill guide on 1 hemipelvis and freehand wire placement was done on the contralateral hemipelvis. Postprocedural CTs were obtained, and 2-D and 3-D analyses were performed. The Student t-test and Wilcoxon rank sum test were used to compare groups. A Pearson correlation coefficient was performed to evaluate the in-group correlation., Results: Likert scores that assessed the ease of the procedure were significantly greater (P = .04) and the incision length was significantly shorter (P = .016) in the 3-DP drill guide group compared with the freehand group. The time of the procedure, the number of attempts to obtain accurate Kirschner wire placement, and fluoroscopy images did not differ (P > .05) between application groups. Drill tracks were primarily confined to the sacral body, with minor projected screw thread cortical breeches occurred in 1 cadaver in the freehand group and 2 cadavers in the 3-DP drill guide group., Clinical Relevance: The 3-DP drill guide simplified appropriate iliosacral Kirschner wire placement through a smaller incision compared with freehand drilling and would appear to be an efficient, practical instrument to facilitate accurate fluoroscopic-assisted screw placement when stabilizing sacroiliac luxations in dogs.

Objective:  The aim of this study was to compare the biomechanical properties of two minimally invasive arthrodesis techniques of the equine proximal interphalangeal (PIP) joint (three transarticular 5.5-mm cortical screws [AO-3TLS] vs. two transarticular 7.0-mm headless cannulated multi-use compression screws [MUC-2TS]) in dynamic non-destructive testing and compression testing to failure., Study Design:  The experimental study included six pairs of cadaveric adult equine forelimbs; one limb from each horse was randomly assigned to one of the treatments, and the contralateral limb was submitted to the remaining treatment. The dynamic test was performed alternating non-destructive compression tests at a displacement rate of 5 mm/min up to 5,000 N and sinusoidal compressive cyclic tests at 6 Hz, using a 3,600-N amplitude for 8,550 cycles. Construct stiffness and maximum sagittal plane rotation about the PIP joint markers were determined during the dynamic test. After the dynamic test reached 136,800 cycles, the monotonic compressive test until failure was performed on each construct: load, displacement and sagittal plane rotation about the PIP joint marker at failure were analysed., Results:  The evaluated biomechanical properties showed no statistical difference between the AO-3TLS and MUC-2TS treatment groups in any of the ramps of the dynamic non-destructive test and in the compression loading until failure test., Conclusion:  The MUC-2TS treatment produced biomechanical properties equivalent to the AO-3TLS treatment for PIP joint arthrodesis., Competing Interests: None declared., (Thieme. All rights reserved.)

Objectives: (1) To evaluate the accuracy of an aiming device on placement of humeral transcondylar screws compared to fluoroscopic methods. (2) To compare experience level on outcome., Study Design: Randomized, match pair, prospective ex-vivo study., Sample Population: A total of 68 dogs., Methods: Canine cadaveric forelimbs were randomly assigned to either aiming device or fluoroscopic-guided groups, and to diplomate or resident. Digital radiography was used to evaluate screw trajectory deviation and eccentricity on the humeral condyle. Procedure time, outcome based on experience, and complications were recorded., Results: The aiming device screw trajectory angle was decreased in the right limb (1.9 ± 1.1°) compared with the left (3.6 ± 1.1°, p = .0178), and compared to fluoroscopy (3.4 ± 1.1° p = .0128). There was no difference between leg laterality with fluoroscopy (p = .9979). Trajectory angle was increased with resident versus diplomate (3.4 ± 1.1° and 2.5 ± 1.1° respectively, p = .0366). Eccentricity deviation was decreased using fluoroscopy versus aiming device (3.1 ± 0.36 mm, 4.2 ± 0.36 mm, respectively, p = .0017). The risk of joint involvement was 8 times greater in aiming device groups, though not significant (p = .0575). Significant complications included increased drill attempts in fluoroscopic groups (p = .0237)., Conclusion: The aiming device provided accurate placement of transcondylar screws, in terms of both position on the condyle and trajectory angle. Results were similar to fluoroscopic-guided method., Clinical Significance: An aiming device is an acceptable means of placing humeral transcondylar screws. The use of the aiming device had an eight times increased risk of joint involvement compared to fluoroscopy., (© 2023 American College of Veterinary Surgeons.)

Background: Rupture of the common calcaneal tendon is the second most frequent tendon rupture in dogs and may lead to severe lameness and pain. Surgical repair consists of re-apposition of the damaged tendon ends using sutures, but this type of repair is not always possible especially if the tendon has retracted. Tendon augmentation with an ultra-high molecular weight polyethylene (UHMWPE) implant is a recent solution to support the sutures and allow the repair of the canine calcaneal tendon. However, its biomechanical fixation strength remains untested for this pathology., Aim: To evaluate the biomechanical fixation strength of a UHMWPE implant for the repair of the canine calcaneal tendon., Methods: Ex-vivo biomechanical study was carried out on eight cadaveric hindlimbs from four adult dogs. Hindlimbs were tested under two independent modalities: proximal tendinous fixation (PTF) and distal calcaneus fixation (DCF), using a testing machine. PTF was achieved by eight simple interrupted polypropylene sutures performed through the UHMWPE implant. The latter was sandwiched inside the gastrocnemius tendon, which had previously been incised over about 5 cm longitudinally, and through the tendon of the superficial digital flexor. DCF was performed using an interference screw, which locked the UHMWPE implant into a calcaneus tunnel drilled perpendicularly., Results: Yield, failure load, and linear stiffness (mean ± SD) for the DCF modality were 920 ± 139 N, 1,007 ± 146 N, and 92 ± 15.21, respectively, which were greater than for the PTF modality (663 ± 92 N, 685 ± 84 N and 25.71 ± 5.74, respectively, p < 0.05). Failure modes were different between fixation modalities: for PTF it was suture breakage ( n = 7/8), while for DCF it was implant damage and slippage ( n = 8/8)., Conclusion: The biomechanical fixation strength of the UHMWPE implant was greater for DCF than that of PTF, and should be suitable for calcaneal tendon repair in dogs. The clinical prediction of rupture of this calcaneal tendon repair will occur at the level of the PTF., Competing Interests: The authors have no conflicts of interest to declare.

Frontal plane slab fractures account for the majority of third carpal bone (C3) fractures in racing and performance horses. Recommended treatment is stabilization with a lagged AO cortical screw. Associated complications are fragment splitting, fragment spinning, and irritation of dorsal soft tissue structures. A novel, headless, cannulated screw with interlocking threads the Headless Compression Screw Fastener (HCSF) has been developed to resist multidirectional forces and bending moments; however, it has not been applied in the horse. Simulated C3 frontal plane slab fractures were created in nine paired carpi from equine cadaver limbs, fixed with either the HCSF or AO cortical bone screw, and loaded in shear to failure. The effect of screw type on stiffness, maximum load to failure, and yield load was assessed in separate linear mixed models. No significant (P< .05) difference between screw types was detected in terms of maximum load to failure (P= .084), stiffness (P= .26), or yield load (P= .088). Mode of failure was screw bending in all specimens. For some samples in both groups, failure was associated with the sagittal fracture at the screw-bone interface. The HCSF was successfully used to repair simulated third carpal bone fractures. The different head and thread pitches of the HCSF effectively compressed the fracture. The headless design eliminates the need for counter sinking. There was no significant difference in maximum load to failure, stiffness, nor yield load compared to the cortical screws. These results invite clinical application to be investigated., Competing Interests: Declarations of interest None, (Copyright © 2022. Published by Elsevier Inc.)

Objectives:  The main aim of this study was to evaluate the feasibility of minimally invasive stabilization with polyaxial screws-rod using neuronavigation and to assess accuracy and safety of percutaneous drilling of screw corridors using neuronavigation in thoracolumbar spine and compare it between an experienced and a novice surgeon., Study Design:  Feasibility of minimally invasive polyaxial screws-rod fixation using neuronavigation was first performed in the thoracolumbar spine of two dogs. Accuracy and safety of drilling screw corridors percutaneously by two surgeons from T8 to L7 in a large breed dog using neuronavigation were established by comparing entry and exit points coordinates deviations on multiplanar reconstructions between preoperative and postoperative datasets and using a vertebral cortical breach grading scheme., Results:  Feasibility of minimally invasive stabilization was demonstrated. For the experienced surgeon, safety was 100% and mean (standard deviation) entry point deviations were 0.3 mm (0.8 mm) lateral, 1.3 mm (0.8 mm) ventral and 0.7 mm (1.8 mm) caudal. The exit points deviations were 0.8 mm (1.9 mm) lateral, 0.02 mm (0.9 mm) dorsal and 0.7 mm (2.0 mm) caudal. Significant difference in accuracy between surgeons was found in the thoracic region but not in the lumbar region. Accuracy and safety improvement are noted for the thoracic region when procedures were repeated by the novice., Conclusion:  This proof of concept demonstrates that using neuronavigation, minimally invasive stabilization with polyaxial screws-rod is feasible and safe in a large breed dog model., Competing Interests: None declared., (Thieme. All rights reserved.)

Background: To investigate the incidence of implant-related complications when humeral unicondylar fractures in immature dogs are stabilised with a transcondylar bone screw and epicondylar Kirschner wire (K-wire)/pin., Methods: Records of cases treated by the author in this clinic over a 10-year period were screened for those involving humeral condylar fractures. These were then reduced to include those patients who were less than 7 months of age with unicondylar fractures and follow-up radiographs., Results: Thirty fractures in 29 dogs met the inclusion criteria. All of these had been stabilised with a transcondylar bone screw and epicondylar K-wire. Fracture healing was documented in all dogs. Surgical site infection was not recorded. Implant-related major complications were reported in four (13%) dogs and successfully treated by either implant removal or replacement. Short-term outcome was judged as excellent in 23 out of 30 and good in seven out of 30 of these fractures., Conclusion: The use of a transcondylar bone screw in combination with an epicondylar K-wire is an appropriate fixation method for humeral unicondylar fractures seen in puppies less than 7 months of age., (© 2022 British Veterinary Association.)

Objective:  The aim of this study was to report the short-term clinical and radiographic outcome for the treatment of femoral capital physeal fractures with cortical positional screws in cats., Study Design:  Medical records and radiographs of cats with femoral capital physeal fractures stabilized with cortical positional screws were retrospectively reviewed. Signalment, bodyweight, femoral head affected, fracture classification, fracture reduction, implants, concurrent orthopaedic injuries, osteoarthritis, femoral neck osteolysis, complications and 6-week follow-up clinical results were recorded. A short- to long-term follow-up was performed by telephone questionnaire with the owners., Results:  Forty-six fractures in 39 cats met the inclusion criteria. In 45/46 fractures, radiographic signs of bone healing were present and 35/39 cats were assessed as walking normally by a veterinarian at 6-week follow-up. There was a significant increase in radiographic signs of osteoarthritis ( p =0.037) and femoral neck osteolysis ( p =0.001) on 6-week follow-up radiographs. Pre- and postoperative osteoarthritis and femoral neck osteolysis were not associated with clinical outcome. The mean follow-up period for the telephone questionnaire was 48 months (range, 5-147 months). Seven out of 25 owners reported a gait abnormality in the short- to long-term., Conclusion:  Femoral capital physeal fractures in cats can be treated successfully with the use of cortical positional screws. This technique may be considered as an alternative to other primary fixation techniques and salvage procedures for the treatment of femoral capital physeal injuries in cats. This technique seemed successful in cats with a low-grade preoperative femoral neck osteolysis., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective: To assess the feasibility and mechanical stability of sacroiliac (SI) joint stabilization using 2 short 3.5 mm cortical screws, each spanning an average of 23% of the width of the sacral body., Study Design: Cadaveric experimental study., Sample Population: Twenty-four canine pelvis specimens., Methods: Pelvis specimens were prepared by disarticulation of the left SI joint and osteotomy of the left pubis and left ischium, and stabilized using a single long lag screw (LLS), 2 short lag screws (SLS) or 2 short positional screws (SPS). Computed tomography (CT) imaging was used to determine standardized screw lengths for each group and was repeated following implant insertion. Specimens were secured within a servohydraulic test frame and loaded through the acetabulum to simulate weight bearing under displacement control at 4 mm/min for 20 mm total displacement. Group mechanical testing data were compared., Results: Peak load, yield load, and stiffness were more than 2 times greater in both the SLS and SPS groups when compared with the LLS group. No mechanical difference was identified between the short-screw groups., Conclusion: Sacroiliac luxation fixation using 2 short screws created a stronger, stiffer construct when compared with fixation using a single lag screw spanning 60% of the width of the sacral body. No mechanical advantage was observed between short screws inserted in positional vs. lag fashion., Clinical Significance: Sacroiliac luxation fixation using 2 short screws creates a mechanically superior construct with a larger region of acceptable implant positioning and potentially reduced risk of iatrogenic injury compared with conventional fixation., (© 2022 The Authors. Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Objective:  The main aim of this study was to compare the biomechanical properties of caudal cervical vertebral stabilization using bicortical transpedicular pins with polymethylmethacrylate (PMMA) versus transvertebral body polyaxial screws and connecting rods with or without an interbody distractor., Study Design:  Ten canine cervical vertebral columns (C2-T3) were used. Four models (intact, transvertebral body polyaxial screw with interbody distractor [polyaxial + distractor], transvertebral body polyaxial screw without interbody distractor [polyaxial - distractor] and bicortical transpedicular pins/polymethylmethacrylate [pin-PMMA]) were applied to C6-7 sequentially on the same specimens. Angular range of motion (AROM) in the form of flexion and extension was measured at C4-5, C5-6 and C6-7 in all groups., Results:  Treated vertebral specimens had significantly less AROM than unaltered specimens. There was no significant difference in AROM between the experimental groups at C6 and C7. Angular range of motion ratio in flexion-extension was 80.8, 72.7 and 78.3% for polyaxial + distractor, polyaxial - distractor and pin-PMMA groups, respectively, which were less than the intact group. There was no significant increase in the range of motion of the adjacent vertebrae after stabilization., Conclusion:  Stabilization obtained with transvertebral body polyaxial screws was comparable to that from the well-established bicortical pins/PMMA construct. Association of an intervertebral distractor did not change AROM of the polyaxial screw constructs., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective:  The aim of this study was to evaluate the effect of screw insertion angle and insertion torque on the mechanical properties of a 3.5 fixed-angle locking plate locking compression plate (LCP) and 3.5 variable-angle locking plate polyaxial locking system (PLS)., Methods:  In the LCP group, screws were placed abaxially at 0, 5 and 10 degrees. In the PLS group, screws were placed at 0, 5, 10, 15 and 20 degrees abaxially. The insertion torque was set to 1.5 and 2.5 Nm in the LCP and PLS groups respectively. A load was applied parallel to the screw axis, and the screw push-out force was measured until the locking mechanism was loosened., Results:  The 3.5 LCP showed higher push-out strength than the 3.5 PLS when the screws were placed at 0 degree regardless of the insertion torque. The off-axis insertion of 3.5 LCP locking screws resulted in a significant decrease in push-out strength ( p  < 0.05). A higher insertion torque value significantly increased the screw holding strength for the 3.5 LCP ( p  < 0.05). The 3.5 PLS system had a significantly higher push-out force when the screws are at 0 degree than at 5, 10 and 15 degrees, and 20 degrees ( p  < 0.05) at any given insertion torque. An increase in the insertion torque did not have a significant effect on the push-out strength of the 3.5 PLS locking system., Conclusion:  The 3.5 PLS is more sensitive to the screw insertion angle than to the insertion torque, whereas the 3.5 LCP is affected by both factors. Placing 3.5 LCP locking screws off-axis significantly reduces the screw holding strength; therefore, this approach has to be avoided. The findings of our research indicate that a 1.5 Nm torque can be used for a 3.5 PLS., Competing Interests: The authors declare no conflicts of interest related to this study. J.K. reports that PLS implants were donated by Aesculap B. Braun, and LCP implants were donated by De Puy Synthes. T.B., P.Z., B.G., and D.L., report non-financial support from Aesculap B Braun and DePuySynthes, during the conduct of the study., (Thieme. All rights reserved.)

Objective:  The aim of this study was to evaluate the influence of near-cortical over-drilling holes on the mechanical behaviour of locking plate constructs applied in maned wolf's femur by using mechanical testing and finite element method (FEM)., Study Design:  Seven pairs of adult maned wolves ( Chrysocyon brachyurus ) femur bones were randomly distributed into four groups. In all groups, a 3.5 mm locking compression plate, designed with 12 combi-holes and one locked, was applied to the lateral surface of the femur. G1 ( n  = 4) received bicortical locking screws placed in holes 1, 3, 5, 8, 10 and 12. In G2 ( n  = 5), the plate was applied as used in G1, but the application of the locked screws involved the near-cortical over-drilling technique. In G3 ( n  = 4), the plate was applied as used in G2, but the size of the near-cortical over-drilling was larger. The combi-holes 6 and 7 were maintained over a 10 mm fracture gap without screws. All constructs were tested for failure in the axial load. The axial load was applied eccentrically to the femoral head., Results:  Statistical differences were observed in the maximum load with G3 > G1 and G3 > G2, and in the deflection with G2 > G1 and G2 > G3. The FEM showed the lowest total displacement of the bone-plate constructs as well as of the plate in G1 compared with G2 and G3., Conclusion:  The near-cortical over-drilling technique used in unstable fractures induced in the maned wolf's femur showed by static axial compression test that maximum load and deflection are dependent on drill hole size induced in the near-cortex. Based on FEM, the lowest total displacement of the bone-plate constructs was observed in Group 1., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective: Determine compression generated by lag and neutral screws over 12 h using two bone analogs., Study Design: Experimental study., Sample Population: Bone analogs were made of composite synthetic bone (CSB) or three-dimensional printed polylactic acid (PLA). Analogs had a 2 mm exterior shell with a 10 mm thick internal layer of open-cell material., Methods: Bone analogs were opposed, making a 4-sided box with open ends. A central channel contained the sensor and the screws passed through it to engage both paired analogs. Four screw/analog conditions were tested: neutral and lag screw with bicortical engagement, neutral and lag screw with unicortical engagement. All screws were tightened to 2 Nm torque and compression values recorded at 0, 0.5, 1, 2, 6, and 12 h (six trials per condition). Medians were compared across groups for statistical significance., Results: There was no difference in median compression between lag and neutral bicortical screws. For PLA, greater median compression was generated by neutral (median 437 N) and lag (median 379 N) bicortical screws compared to neutral unicortical screws (median 208 N, p < .001); lag bicortical screws generated greater median compression than lag unicortical screws (median 265 N, p = .012). For CSB, lag bicortical screws (median 293 N) generated greater median compression than neutral unicortical screws (median 228 N, p = .008)., Conclusion: Lag and neutral screws generated similar compression. Bicortical screws had higher median compression than unicortical screws in bone analogs., Clinical Significance: Neutral screws generate compression in cancellous bone analogs that can be increased with bicortical bone engagement., (© 2022 The Authors. Veterinary Surgery published by Wiley Periodicals LLC on behalf of American College of Veterinary Surgeons.)

Objectives:  (1) To compare the ability of standard computed tomography (CT) scale (SCTS) and extended CT scale (ECTS) images, produced using conventional CT technology, to provide detailed assessment of metal screws in vitro. (2) To assess how screw size, type, and orientation relative to the Z -axis of the gantry affect implant assessment. (3) To test the ability of SCTS, ECTS, and radiography to diagnose screw failure when there is negligible screw fragment displacement., Study Design:  Part 1: 12 screws of different size, type, and composition were scanned in three orientations (parallel or 0°; oblique or 45°; and perpendicular or 90°) relative to the Z -axis of the gantry. SCTS and ECTS reconstructions were made for each screw, in each plane, to assess implant shape, structure, and diameter. Part 2: fatigue-failure was induced in four screws commonly used to stabilize canine humeral intracondylar fissures. Screws were then reassembled achieving grossly perfect apposition and alignment of the fragments. Ability to detect implant failure was tested using SCTS, ECTS, and radiography., Results:  ECTS provided better screw assessment compared with SCTS resulting in clear visualization of the structure in 8/12 versus 0/12 screws and shape in 12/12 versus 11/12 screws; however, results were affected by screw size, type, and orientation. ECTS identified all in vitro screw fractures with negligible screw fragment displacement; however, success was affected by screw orientation: 4/4 fractures identified with a 90° angle, 1/4 for 45°, and 0/4 for 0°. SCTS and radiography did not identify any of them., Conclusion:  The results indicate that ECTS reconstructions are useful for assessment of metal screws and for detection of nondisplaced screw fractures., Competing Interests: None declared., (Thieme. All rights reserved.)

Objectives: The objective of this study was to report outcome and postoperative complications following stabilisation of humeral condylar fractures in skeletally immature French bulldogs with a transcondylar screw combined with locking or hybrid locking plates., Materials and Methods: Medical records from one referral hospital were reviewed to identify skeletally immature French bulldogs with humeral condylar fractures treated with a transcondylar screw and epicondylar locking or hybrid locking plates crossing the distal humeral physis., Results: Forty-five fractures in 41 different dogs with a mean age of 4 months (range 3.5 to 5) were identified. Six cases had complications: two (4.4%) minor and four (8.9%) major. Short-term clinical outcome was excellent in 35 (77.8%), good in nine (20%) and poor in one (2.2%) case. Forty-one of 45 fractures reached radiographic union without further surgical intervention; the remaining four cases reached union following revision surgery. Long-term owner assessed outcome by telephone interview was graded as excellent in all available cases (26 of 41 dogs)., Clinical Significance: This study suggests that the stabilisation of humeral condylar fractures in skeletally immature French bulldogs with combinations of a transcondylar screw and epicondylar locking or hybrid locking plates crossing the distal humeral physis was safe and led comparable outcomes and complication rates to previous reports., (© 2022 British Small Animal Veterinary Association.)

Objective: To evaluate the biomechanical properties of the mandibles of cats with experimentally created osteotomies simulating oblique ramus fractures, which were stabilized with malleable L-miniplates with either locking screws [locking construct (LC)] or nonlocking screws [nonlocking construct (NLC)], compared with those for intact mandibles., Samples: 20 mandibles from 10 adult cat cadavers., Procedures: A block study design was adopted to allocate the mandibles of each cadaver to 2 of the 3 test groups (LC, NLC, or intact mandible). Mandibles within each cadaver were allocated systematically to a test group. For mandibles assigned to an LC and an NLC, a complete oblique osteotomy was performed from the mid rostral aspect of the ramus in a caudoventral direction. All mandibles were loaded in a single-load-to-failure test through cantilever bending. Load and actuator displacement were recorded simultaneously. Mode of failure and radiographic evidence of damage to tooth roots and the mandibular canal were evaluated. Biomechanical properties were compared among the groups., Results: No iatrogenic tooth root damage was evident, but all mandibles with an LC and an NLC had evidence of screw invasion into the mandibular canal. Plated mandibles had significantly less stiffness and bending moment than intact mandibles. Stiffness was not significantly different between the LC and the NLC; the NLC had a greater bending moment at failure than the LC. The pre-yield stiffness of plated mandibles decreased when the number of screw holes overlapping the mandibular canal increased., Clinical Relevance: The use of a malleable L-miniplate in a caudal mandibular fracture model is feasible. Both the LC and the NLC were inferior mechanically to intact mandibles. Type of construct used did not affect the construct stiffness significantly in tested mandibles.

Background: One of the traumatic fractures occurring in the hindlimb of the foals is physeal fractures of the tibia. The most common type of proximal tibial fracture in foals is reported to be Salter-Harris type II., Case Presentation: This case report describes the history, clinical signs, radiographic findings, and surgical management of a proximal physeal fracture of the tibia due to the kick trauma in a 2-weeks-old Kurdish female foal, with signs of left pelvic limb lameness, valgus deviation with non-weight-bearing, non-mobility in stifle region and crepitation in the affected area. In this case, radiography was utilized to confirm the fracture and detect the exact location of the fracture fragments. The Salter-Harris type I accompanied by tibial tuberosity fracture was diagnosed. In this case, a size 4.5 mm seven-hole, T-plate, and cortical bone screws were employed to fix the physeal fracture, and a cortical bone screw was utilized to fix the tibial tuberosity in the normal position. Case follow-up during two months showed no significant complications, and the patient was fully recovered (no lameness anymore)., Conclusions: To our knowledge, this is the first report of Salter-Harris type I fracture in proximal tibia accompanied by tibial tuberosity fracture in a foal treated by a T-plate implant. A cortical screw in lag fashion for tibial tuberosity was utilized in this case for the first time, and the results were satisfying. T-Plate fixation can be recommended as an effective surgical treatment for proximal tibial fractures in foals., (© 2022. The Author(s).)

Objective: To report the incidence of medial epicondylar fissure fracture (MEFF) after medial-to-lateral transcondylar screw placement in dogs with humeral intracondylar fissure (HIF) and to identify risk factors for MEFF., Study Design: Retrospective study., Sample Population: Seventy-four client-owned dogs (88 elbows)., Methods: Medical records of dogs surgically treated for HIF, and postoperative imaging studies were reviewed for demographics, fracture characteristics, and repair techniques. The width of the transcondylar screw was expressed relative to the height of the condyle. Screw angle and degree of countersinking were recorded. Information from case records and follow-up radiographs were used to identify complications., Results: Medial epicondylar fissure fracture was identified in 10 elbows (11.4%) following medial-to-lateral transcondylar screw placement: 4 cases were detected intraoperatively, 2 on immediate postoperative radiographs, 1 during routine radiographic follow up, and 3 when radiographs were reviewed for this study. A larger relative screw size was found to increase the risk of MEFF (P = .004, OR = 1.5). Fifteen additional complications were identified in 13/80 elbows at a median of 6 weeks postoperatively (range 1-56 weeks). Screw loosening was the most frequent complication (n = 9) and was the only complication in dogs with MEFF (n = 3); MEFF tended to increase the risk of perioperative screw loosening (P = .06)., Conclusion: Medial epicondylar fissure fracture occurred in 10/88 elbows treated for HIF and was more common in elbows treated with a larger screw size relative to the height of the condyle., Clinical Significance: Placing transcondylar screws with a diameter inferior to 41% of the height of the condyle is recommended to avoid MEFF. Medial epicondylar fissure fracture appears to have a low clinical significance in the perioperative period, although its effect on long-term outcome remains unknown., (© 2022 American College of Veterinary Surgeons.)

Objective: To determine the influence of screw head diameter on equine condylar fracture fixation with 5.5 mm cortical screws., Study Design: Ex vivo, biomechanical study, blinded, matched-pair design., Sample Population: Fifteen pairs of equine third metacarpal (MC3) bones., Methods: Lateral condylar fractures were simulated by parasagittal osteotomies and repaired pairwise by 2 × 5.5 mm cortical screws of 8 mm (standard) or 10 mm (modified) head diameter. Interfragmentary compression at maximum screw insertion torque was measured. The instrumented specimens were pairwise stratified for biomechanical testing under the following modalities (n = 5): (1) screw insertion torque to failure, (2) quasi-static axial load to failure, and (3) cyclic axial load to 2 mm displacement followed by failure. Tests (1) and (2) were analyzed for yield, maximum, and failure torque/angle and load/displacement, respectively. Number of cycles to 2 mm displacement and failure was assessed from test (3)., Results: Maximum insertion torque was greater, and failure angle smaller, when constructs repaired with modified screws were tested (8.1 ± 0.5 vs. 7.4 ± 0.5 Nm; P = .0047 and 550 ± 104 vs. 1130 ± 230; P = .008). Axial yield (7118 ± 707 vs. 5740 ± 2267 N; P = .043) and failure load (12 347 ± 3359 vs. 8695 ± 2277 N; P = .043) were greater for specimens repaired with modified screws. No difference was detected between constructs in the number of cycles to 2 mm displacement., Conclusion: Condylar MC3 osteotomies repaired with modified 5.5 mm cortical screws sustained greater maximal hand torque insertion, smaller insertion failure angle and 1.4 fold greater quasi-static failure forces than constructs repaired with standard 5.5 mm screws., Clinical Significance: Use of modified screws with larger heads may improve the fixation of condylar fractures in horses. These results provide evidence to justify clinical evaluation in horses undergoing fracture repair., (© 2022 American College of Veterinary Surgeons.)

Background: Cranial cruciate ligament rupture (CCLr) is the most common cause of hind limb lameness in dogs. Currently, surgical management of CCLr is mostly performed using tibial osteotomy techniques to modify the biomechanical conformation of the affected stifle. These surgical techniques have a significant complication rate, associated with persistent instability of the stifle which may lead to chronic postoperative pain. Over the last decade, studies have been published on various techniques of anatomical caudal cruciate ligament reconstruction in veterinary practice, using physiological autografts or woven synthetic implants., Aim: The aim of this ex vivo biomechanical study is to investigate the ex vivo dynamic biomechanical behavior of a synthetic implant [ultrahigh molecular weight polyethylene (UHMWPE) implant] fixed with interference screws for the treatment of CCLr in dogs, according to a fatigue protocol (48 hours per test)., Methods: Seven stifles from four skeletally mature canine cadavers were implanted with the synthetic implant. It was fixed with four interference screws inserted in transversal and oblique tunnels in both the distal femur and the proximal tibia. For each case, 100,000 cycles were performed at 0.58 Hz, with traction loads ranging from 100 to 210 N., Results: Neither screw-bone assembly rupture nor a pull-out issue was observed during the dynamic tests. Linear stiffness of the implants associated with a fixation system with four interference screws increased over time. The final displacement did not exceed 3 mm for five of the seven specimens. Five of the seven synthetic implants yielded to a lengthening in functional range (0-3 mm). Linear stiffness was homogeneous among samples, showing a strong dynamic strength of the interference screw-based fixations of the UHMWPE implant in the femoral and tibial bones., Conclusion: This study completes the existing literature on the biomechanical evaluation of passive stifle stabilization techniques with a testing protocol focused on cyclic loading at a given force level instead of driven by displacement. These biomechanical results should revive interest in intra-articular reconstruction after rupture of the CCLr in dogs.

Objectives:  The aim of this study was to measure and compare the stiffness and cyclic fatigue of two plate-bone model constructs, with either two or three locking screws per fragment, under cyclic compression., Methods:  A 10-hole 3.5 mm stainless steel locking compression plate (LCP) was fixed 1 mm from a synthetic bone model in which the fracture gap was 47 mm. Two groups of 10 constructs, prepared with either two or three bicortical locking screws placed at the extremities of each fragment, were tested in a load-controlled compression test until failure., Results:  The three-screw constructs were stiffer than the two-screw constructs (196.75 ± 50.48 N/mm and 102.43 ± 22.93 N/mm, respectively) and the actuator displacements of the two-screw constructs were higher (18.02 ± 1.07 mm) than those of the three-screw constructs (14.48 ± 2.25 mm). The number of cycles to failure of the two-screw constructs was significantly lower (38,337.50 ± 2,196.98) than the that of the three-screw constructs (44,224.00 ± 1,515.24). Load at irreversible deformation was significantly lower in the two-screw constructs (140.93 ± 13.39 N) than in the three-screw constructs (184.27 ± 13.17 N). All constructs failed by plate bending at the gap between the two cylinders., Clinical Significance:  Omission of the third innermost locking screw during bridging osteosynthesis subjected to compression forces led to a 13.3% reduction in the number of cycles to failure and a 23.5% reduction of the load withstood by the plate before plastic deformation occurred., Competing Interests: None declared., (Thieme. All rights reserved.)

Objective: To determine the failure method of simulated equine medial femoral condyle (MFC) subchondral bone defects under compression and the influence of screw placement on failure resistance., Study Design: In vitro study., Sample Population: Composite disks (CD) simulating the moduli of yearling bone in the MFC., Methods: Four CD conditions were tested, all with a 12.7 mm void (n = 6 per condition): intact (no void), void only, void with a 4.5 mm screw placed in neutral fashion, and void with a 4.5 mm screw placed in lag fashion. Composite disks of each condition were tested under monotonic compression to 6000 N and cyclic compression to 10 000 cycles. Observable failure, load at first observable failure, and displacement at peak 2000 N load were compared among conditions., Results: Specimens failed by cracking at the superior aspect of the void or the screw exit hole. After monotonic loading, cracks were observed 6/6 CD with a void, 6/6 CD with a void/lag screw, and 5/6 CD with a void/neutral screw. After cyclical testing, cracks were noted only on the superior aspect of 6/6 CD with a void and 3/6 CD with a void/lag screw. Displacement at peak load was 0.06 mm (intact), 0.32 mm (void), 0.24 mm (void/lag screw), and 0.11 mm (void/neutral screw)., Conclusion: Model MFC voids failed by superior cracking that was resisted by lag and neutral screw placement., Clinical Significance: Neutral screws may be an acceptable treatment for subchondral lucencies in the MFC., (© 2022 American College of Veterinary Surgeons.)

Objective:  Application of extended computed tomography scale (ECTS) reconstruction to diagnose metal implant failure has been described in a single case report. The purpose of this study was to compare the features and visibility of humeral transcondylar screw fractures in standard CT scale (SCTS) and ECTS images., Study Design:  Case series: CT images of dogs with fractured transcondylar screws were retrospectively reviewed and described in both SCTS and ECTS images., Results:  Five dogs with a total of six transcondylar screw failures (five right and one bilateral) were reviewed. All cases had an ongoing humeral intercondylar fissure with varying degrees of stress remodelling. The fracture was seen in all screws on ECTS images, however only in three implants on SCTS images. The measured fracture gap was larger in ECTS images in all cases (range: + 0.14 mm to + 0.28mm). The three smallest fracture gaps were not seen on SCTS images. A subtle hypoattenuating streak (artefact) was visible adjacent to the screw fracture in 5/6 of cases using SCTS images. All screw fractures occurred parallel and often slightly medial to the humeral intercondylar fissure., Conclusion:  Implant failure is only seen with larger fracture gaps in SCTS images, with 3/6 screw fractures not visible in SCTS compared with ECTS. A hypoattenuating streak extending perpendicular to the implant in SCTS images is suggestive of screw fracture even if this is not directly visible., Competing Interests: None declared., (Thieme. All rights reserved.)