Search

(CoCrFeNi)1−xMox thin films with various Mo content (0–10 at.%) were grown by magnetron sputtering on a stainless steel substrate. The films with 0–2 at.% presented two crystal structures: one FCC phase and one sigma phase, while films with higher Mo content only had the FCC structure. All films have a (111) texture and follow the topography of the substrate. The corrosion resistance of the films was evaluated in 0.05 M H2SO4 at room temperature and at 80 °C. It was observed that the corrosion current densities considerably decreased for Mo > 2 at%, and that the current densities were higher at the elevated temperature. Scanning Kelvin Probe Force Microscopy showed a large potential difference between the main FCC phase and sigma phase for the Mo0–2 films. This would suggest that preferential dissolution of the FCC phase occurs over the sigma and reduces the corrosion resistance. Such preferential dissolution does not occur for the higher Mo content films with only the FCC phase. The high corrosion resistance was also attributed to the inhibition of Fe and Cr dissolution by Mo and the stabilisation of the Cr enriched oxide by incorporating Mo oxides into the passive film, identified by X-ray photoelectron spectroscopy. The low corrosion current densities (below 1 µA/cm2) make these thin films possible candidates for protective coatings of bipolar plates in PEM fuel cells., This study was performed within the Competence Centre FunMat-II and was funded by the Swedish Agency for Innovation Systems (VINNOVA, grant no 2016–05156, and grant no 2019–04881). The authors would also like to acknowledge the Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University (Faculty Grant SFO-Mat-LiU No. 2009 00971)

The skin is the largest organ of the human body. Wounds disrupt the functions of the skin and can have catastrophic consequences for an individual resulting in significant morbidity and mortality. Wound infections are common and can substantially delay healing and can result in non-healing wounds and sepsis. Early diagnosis and treatment of infection reduce risk of complications and support wound healing. Methods for monitoring of wound pH can facilitate early detection of infection. Here we show a novel strategy for integrating pH sensing capabilities in state-of-the-art hydrogel-based wound dressings fabricated from bacterial nanocellulose (BC). A high surface area material was developed by self-assembly of mesoporous silica nanoparticles (MSNs) in BC. By encapsulating a pH-responsive dye in the MSNs, wound dressings for continuous pH sensing with spatiotemporal resolution were developed. The pH responsive BC-based nanocomposites demonstrated excellent wound dressing properties, with respect to conformability, mechanical properties, and water vapor transmission rate. In addition to facilitating rapid colorimetric assessment of wound pH, this strategy for generating functional BC-MSN nanocomposites can be further be adapted for encapsulation and release of bioactive compounds for treatment of hard-to-heal wounds, enabling development of novel wound care materials., Validerad;2023;Nivå 2;2023-03-03 (hanlid);Funder: Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linköping University (SFO-Mat-LiU no. 2009–00971)

Catalysts and electrocatalysts are crucial for energy production and storage. To develop cost-efficient systems taking advantage of functionalized surfaces, the catalysts can be synthesized as nanomaterials or thin films. In this work, cobalt thin films were deposited on low-alloyed steel using magnetron sputtering. The films are uniform with a smooth surface and a thickness of ~400 nm. The films were electrochemically oxidized via anodization to a mix of cobalt oxides, one of them being Co3O4, at room temperature in an alkaline solution. The electrocatalytic performances of the anodized films were evaluated in 1 M KOH electrolyte saturated with oxygen. Cathodic currents in −0.5 mA/cm2 range, corresponding to oxygen reduction reaction (ORR) activity, were measured with cyclic voltammetry. The catalytic activity of the films was evaluated as a function of time. The anodized Co coating exhibited three times higher activity than the steel substrate. The kinetics for the ORR were evaluated through Tafel plots and a slope of 226 mV/decade was found. Post-ORR characterization of the films revealed hexagonal plate-like oxide particles on the surface. After 50 cyclic voltammograms, the film was further oxidized, indicating that the ORR activity also affects the overall surface state of the film. This study demonstrates that thin films, after electrochemical modification, can be electrocatalysts for the oxygen reduction reaction and potentially used for applications in energy production and storage.

Nanocomposites of metal nanoparticles (NPs) and bacterial nanocellulose (BC) enable fabrication of soft and biocompatible materials for optical, catalytic, electronic, and biomedical applications. Current BC–NP nanocomposites are typically prepared by in situ synthesis of the NPs or electrostatic adsorption of surface functionalized NPs, which limits possibilities to control and tune NP size, shape, concentration, and surface chemistry and influences the properties and performance of the materials. Here a self‐assembly strategy is described for fabrication of complex and well‐defined BC–NP composites using colloidal gold and silver NPs of different sizes, shapes, and concentrations. The self‐assembly process results in nanocomposites with distinct biophysical and optical properties. In addition to antibacterial materials and materials with excellent senor performance, materials with unique mechanoplasmonic properties are developed. The homogenous incorporation of plasmonic gold NPs in the BC enables extensive modulation of the optical properties by mechanical stimuli. Compression gives rise to near‐field coupling between adsorbed NPs, resulting in tunable spectral variations and enhanced broadband absorption that amplify both nonlinear optical and thermoplasmonic effects and enables novel biosensing strategies.

Nanocomposites of metal nanoparticles (NPs) and bacterial nanocellulose (BC) enable fabrication of soft and biocompatible materials for optical, catalytic, electronic, and biomedical applications. Current BC-NP nanocomposites are typically prepared by in situ synthesis of the NPs or electrostatic adsorption of surface functionalized NPs, which limits possibilities to control and tune NP size, shape, concentration, and surface chemistry and influences the properties and performance of the materials. Here a self-assembly strategy is described for fabrication of complex and well-defined BC-NP composites using colloidal gold and silver NPs of different sizes, shapes, and concentrations. The self-assembly process results in nanocomposites with distinct biophysical and optical properties. In addition to antibacterial materials and materials with excellent senor performance, materials with unique mechanoplasmonic properties are developed. The homogenous incorporation of plasmonic gold NPs in the BC enables extensive modulation of the optical properties by mechanical stimuli. Compression gives rise to near-field coupling between adsorbed NPs, resulting in tunable spectral variations and enhanced broadband absorption that amplify both nonlinear optical and thermoplasmonic effects and enables novel biosensing strategies., Funding Agencies:Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linköping University 2009-00971Spanish Ministerio de Ciencia, Innovacion y Universidades (MICINN) MAT2016-77391-RSevero Ochoa Centres of Excellence programme - Spanish Research Agency (AEI) SEV-2017-0706

Mesoporous silica films consisting of a monolayer of separated SBA-15 particles with unusually wide and short pores grown on silicon wafers have been fabricated in a simple single-pot-synthesis, and the formation of the films has been studied. A recipe for synthesizing mesoporous silica rods with the addition of heptane and NH4F at low temperature was used and substrates were added to the synthesis solution during the reaction. The films are ∼90 nm thick, have a pore size of 10.7–13.9 nm depending on the hydrothermal treatment time and temperature, and a pore length of 200–400 nm. All pores are parallel to the substrate, open, and easy to access, making them suitable for applications such as catalyst hosts and gas separation. The growth of the films is closely correlated to the evolution of the mesoporous silica particles. Here, we have studied the time for adding substrates to the synthesis solution, the evolution of the films with time during formation, and the effect of hydrothermal treatment. It was found that the substrates should be added within 30–60 s after turning off the stirring and the films are formed within 10 min after addition to the synthesis solution. The study has yielded a new route for synthesizing mesoporous silica films with a unique morphology.

The knowledge of how to control the pore size and morphology of separated mesoporous silica particles is crucial for optimizing their performance in applications, such as molecular sieves and drug delivery systems. In this work, we have systematically studied the effects of various synthesis parameters to gain a deeper understanding of how particle morphologies can be altered. It was found that the morphology for isolated particles of SBA-15 type, with unusually short and wide pores, could be altered from rods to platelets by variations in the NH4F concentration. The pore length is nearly constant (similar to 300 nm) for the different morphologies, but the particle width is increasing from 200 nm to >3 mu m when decreasing the amount of NH4F, and the pore size can be tuned between 10 and 13 nm. Furthermore, other synthesis parameters such as heptane concentration, pH, silica precursor, and additions of ions have also been studied. The trend regarding particle width is independent of heptane concentration, at the same time as heptane increases the particle length up to a plateau value of similar to 500 nm. In all, parameters controlling particle width, length, and pore size have been separated in order to evaluate their function in the particle formation. Additionally, it was found that the formation time of the particles is strongly affected by the fluoride ion concentration, and a mechanism for particle formation for this system, where micelles transform from a foam, to multilamellar vesicles, and finally to cylindrical micelles, is suggested.

A method for synthesizing mesoporous silica films with cylindrical pores perpendicular to the substrate has been developed. The films consist of SBA-15 platelets that are grafted on glass substrates. The grafting is studied in terms of parameters such as pH, substrate functionalization, salt additions, time for TEOS prehydrolysis, and calcination. The best coverage of particles on the substrate was achieved for a low pH in combination with OTS-treated glass substrate. Furthermore, the prehydrolysis time of the TEOS was found to be a key parameter in order to bind the particles to the substrate. These porous films have potential in applications such as catalysis, drug delivery, and as a template for nanoparticle or nanorod, growth.