Search

Thin films based on tungsten oxide (WO3) were grown by nanosecond pulsed laser deposition on alumina printed-circuit boards to fabricate electrochemical sensors for nitrogen dioxide (NO2) detection. Samples exposed to thermal annealing (400 °C for 3 h) were also produced to compare the main properties and the sensor performance. Before gas testing, the morphology and structural properties were investigated. Scanning electron microscopy and atomic force microscopy showed the formation of granular films with a more compact structure before the thermal treatment. Features of the main WO3 phases were identified for both as-deposited and annealed samples by Raman spectroscopy, whereas X-ray diffraction evidenced the amorphous nature of the as-deposited samples and the formation of crystalline phases after thermal annealing. The as-deposited samples showed a higher W/O ratio, as displayed by energy-dispersive X-ray spectroscopy. An Arrhenius plot revealed a lower activation energy (0.11 eV) for the as-deposited thin films, which are the most electrically conductive samples, presenting a better gas response (30% higher than the response of the annealed ones) in the investigated NO2 concentration range of 5–20 ppm at the moderate device operating temperature of 75 °C. This behavior is explained by a larger quantity of oxygen vacancies, which enhances the sensing mechanism. [ABSTRACT FROM AUTHOR]

The development of a stable, non‐toxic material that emits electrons following absorption of visible light may have a major impact on the solar photocatalysis of difficult reactions such as CO2 and N2 reduction, as well as for targeted chemical transformations in general. Diamond is a good candidate, however it is a wide bandgap material requiring deep UV photons ( λ ${{\rm{{\rm \lambda} }}}$ <227 nm) to promote electrons from the valence band into the conduction band. Embedding silver nanoparticles under the diamond surface allows the photoconductivity of the diamond in the spectral region of the surface plasmon resonance to be increased, while also leading to an enhancement of visible light photoemission. Considering the low intensity of the light sources used in this work and the spectral properties of the enhanced photoconductivity and photoemission a mechanism based on plasmonically enhanced photoconductivity which in turn allows surface states emptied by photoemission to be recharged thus leading to enhanced photoemission in the visible range is proposed. [ABSTRACT FROM AUTHOR]

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using an electron beam evaporation technique with the aim of testing them as low cost and low power consumption gas sensors for ozone (O3). Scanning electron microscopy and atomic force microscopy were used to characterize the film surface morphology and quantify the roughness and grain size, recognized as the primary parameters influencing the gas sensitivity due to their direct impact on the effective sensing area. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (<2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3. [ABSTRACT FROM AUTHOR]

Thin films based on barium fluoride (BaFx) have demonstrated the capability to reduce the work function of photovoltaic (PV) anodes in hybrid thermionic devices for the conversion of thermal‐to‐electrical energy. Because PV anodes integrated in thermionic converters can operate at temperatures higher than room temperature, in this study, X‐ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS) were used to investigate the temperature dependence up to 300°C of the chemical and physical properties of BaFx thin‐films, deposited on gallium arsenide and silicon, that represent possible candidates for PV anodes. A correlation between chemical composition and work function reduction by 0.5 ± 0.1 eV for the thin films on both GaAs and Si has been found as a function of temperature from room temperature to 300°C. According to XPS analyses, this effect can be ascribable to the thermal desorption of the first contaminated layers of BaFx coatings. [ABSTRACT FROM AUTHOR]

Tantalum boride is an ultra-refractory and ultra-hard ceramic known so far for its favorable high-temperature thermo-mechanical properties and also characterized by a low spectral emittance, making it interesting for novel high-temperature solar absorbers for Concentrating Solar Power. In this work, we investigated two types of TaB2 sintered products with different porosities, and on each of them, we realized four femtosecond laser treatments differing in the accumulated laser fluence. The treated surfaces were then characterized by SEM-EDS, roughness analysis, and optical spectrometry. We show that, depending on laser processing parameters, the multi-scale surface textures produced by femtosecond laser machining can greatly increase the solar absorptance, while the spectral emittance increase is significantly lower. These combined effects result in increased photothermal efficiency of the absorber, with interesting perspectives for the application of these ceramics in Concentrating Solar Power and Concentrating Solar Thermal. To the best of our knowledge, this is the first demonstration of successful photothermal efficiency enhancement of ultra-hard ceramics using laser machining. [ABSTRACT FROM AUTHOR]

Thin films based on scandium oxide (Sc2O3) were deposited on silicon substrates to investigate the thickness effect on the reduction of work function. X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), energy dispersive X-ray reflectivity (EDXR), atomic force microscopy (AFM), and ultraviolet photoelectron spectroscopy (UPS) measurements were performed on the films deposited by electron-beam evaporation with different nominal thicknesses (in the range of 2–50 nm) and in multi-layered mixed structures with barium fluoride (BaF2) films. The obtained results indicate that non-continuous films are required to minimize the work function (down to 2.7 eV at room temperature), thanks to the formation of surface dipole effects between crystalline islands and substrates, even if the stoichiometry is far from the ideal one (Sc/O = 0.38). Finally, the presence of BaF2 in multi-layered films is not beneficial for a further reduction in the work function. [ABSTRACT FROM AUTHOR]

Pulsed laser deposition operated by an ultra-short laser beam was used to grow in a vacuum and at room temperature natively nanostructured thin films of lead telluride (PbTe) for thermoelectric applications. Different percentages of silver (Ag), from 0.5 to 20% of nominal concentration, were added to PbTe deposited on polished technical alumina substrates using a multi-target system. The surface morphology and chemical composition were analyzed by Scanning Electron Microscope and X-ray Photoelectron Spectroscopy, whereas the structural characteristics were investigated by X-ray Diffraction. Electrical resistivity as a function of the sample temperature was measured by the four-point probe method by highlighting a typical semiconducting behavior, apart from the sample with the maximum Ag concentration acting as a degenerate semiconductor, whereas the Seebeck coefficient measurements indicate n-type doping for all the samples. The power factor values (up to 14.9 µW cm−1 K−2 at 540 K for the nominal 10% Ag concentration sample) are competitive for low-power applications on flexible substrates, also presuming the achievement of a large reduction in the thermal conductivity thanks to the native nanostructuring. [ABSTRACT FROM AUTHOR]