Search

The investigation results of the grid connected photovoltaic single stage microinverter with a new topology are presented. The microinverter is based on the couple of two-switch DC-DC flyback converters and has simple design. The investigation results show that the analyzed microinverter is characterized by the high efficiency and low total harmonic distortion of output voltage., Comment: 4 pages, Conference: The International Conference on Renewable Energy and Energy Efficiency FST Fez, November 8 & 9, 2017

Stacks of superconducting tapes can trap much higher magnetic fields than conventional magnets. This makes them very promising for motors and generators. However, ripple magnetic fields in these machines present a cross-field component that demagnetizes the stacks. At present, there is no quantitative agreement between measurements and modeling of cross-field demagnetization, mainly due to the need of a 3D model that takes the end effects and real micron-thick superconducting layer into account. This article presents 3D modeling and measurements of cross-field demagnetization in stacks of up to 5 tapes and initial magnetization modeling of stacks of up to 15 tapes. 3D modeling of the cross-field demagnetization explicitly shows that the critical current density, $J_c$, in the direction perpendicular to the tape surface does not play a role in cross-field demagnetization. When taking the measured anisotropic magnetic field dependence of $J_c$ into account, 3D calculations agree with measurements with less than 4 % deviation, while the error of 2D modeling is much higher. Then, our 3D numerical methods can realistically predict cross-field demagnetization. Due to the force-free configuration of part of the current density, J, in the stack, better agreement with experiments will probably require measuring the Jc anisotropy for the whole solid angle range, including $J$ parallel to the magnetic field., Comment: 36 pages, 20 figures

High temperature superconducting (HTS) tape can be cut and stacked to generate large magnetic fields at cryogenic temperatures after inducing persistent currents in the superconducting layers. A field of 17.7 T was trapped between two stacks of HTS tape at 8 K with no external mechanical reinforcement. 17.6 T could be sustained when warming the stack up to 14 K. A new type of hybrid stack was used consisting of a 12 mm square insert stack embedded inside a larger 34.4 mm diameter stack made from different tape. The magnetic field generated is the largest for any trapped field magnet reported and 30% greater than previously achieved in a stack of HTS tapes. Such stacks are being considered for superconducting motors as rotor field poles where the cryogenic penalty is justified by the increased power to weight ratio. The sample reported can be considered the strongest permanent magnet ever created., Comment: 9 pages, 10 figures

Superconducting bulk (RE)Ba$_2$Cu$_3$O$_{7-x}$ materials (RE-rare earth elements) have been successfully used to generate magnetic flux densities in excess of 17 T. This work investigates an alternative approach by trapping flux in stacks of second generation high temperature superconducting tape from several manufacturers using field cooling and pulsed field magnetisation techniques. Flux densities of up to 13.4 T were trapped by field cooling at ~5 K between two 12 mm square stacks, an improvement of 70% over previous value achieved in an HTS tape stack. The trapped flux approaches the record values in (RE)BCO bulks and reflects the rapid developments still being made in the HTS tape performance.

The ability of stacks of superconducting tapes to trap large magnetic fields makes them ideal candidates for creating powerful permanent magnets of compact size and mass. Experimentally, several techniques are used to trap the maximum possible field in a given practical application. However, regardless of the magnetization method used, there is a physical limit to the maximum magnetic field that a given superconducting magnet can trap. This limit is given by the geometric design, the particular superconducting material used and the temperature of operation. Knowing the maximum possible trapped field is important for device design as it provides an upper limit for applications such as magnetic bearings or rotating machinery. In this work we present a collection of finite element method (FEM) models in 2D and 3D capable of estimating the maximum trapped field of stacked tape superconducting magnets. The models are computationally fast and can be used to perform parametric studies with ease. For the case of square stacks tape magnets, various sizes are considered and their estimated maximum trapped field is compared with experimental results.