Search

Paper manufacturers have long used silicone as the coating agent for release liners. However, silicone‐based release paper is very difficult to recycle due to covalent bonds between silicone and fibers. The most suitable solution to overcome this problem is to use alternative coating materials with adequate release properties, provided that they can be easily repulped in typical paper recycling facilities. We proposed a coating agent composed of phosphate esters and dimethylacetamide in order to manufacture a recyclable and efficient release paper. Analyses carried out on coated sheets showed that phosphate esters allowed the formation of a surface with adequate release properties (low peeling force and surface free energy). In addition, the residual adhesion values obtained with phosphate esters confirmed that they are well anchored on the backing paper surface, thus limiting the mass transfer to the adhesive tape. [ABSTRACT FROM AUTHOR]

Phosphorylated fibers offer a broad range of applications, particularly in thermal insulation, notably with wood fibers, provided they exhibit improved mechanical characteristics. Despite encountering challenges in applying traditional papermaking methods, the creation of paper or board sheets with phosphorylated pulp fibers remains a challenge. Findings suggest that phosphorylation-modified fibers show increased roughness. Moreover, in comparison with unbeaten kraft sheets (KF) and thermomechanical pulp sheets (TMP), those made from phosphorylated kraft fibers (PKF), using a cationic coagulant and a flocculant, demonstrate significant enhancements in burst index, break index, and tensile energy absorption by 2.12 times, 1.7 times, and 2.77 times, respectively. Similarly, phosphorylated TMP sheets, prepared with a dual polymeric system (coagulant/flocculant), exhibit improvements of 1.42 times, 1.33 times, and 1.82 times, respectively, in these properties. The study emphasizes the ameliorating effect of cationic polymeric agents on the charge impact of phosphorylated fibers on overall sheet quality, while also highlighting the substantial influence of hot-pressing lignin-containing paper on all determined physical properties. [ABSTRACT FROM AUTHOR]

Transverse compaction of fibre reinforcements has significant importance in the production of complex dry fibre preforms for the resin transfer moulding (RTM) process of composite materials. This work investigates, for the first time, the planar compaction of phosphorylated stacks of unidirectional (UD) reinforcements made of flax yarns held together by a thin layer of short flax fibres. Planar compaction tests were carried out to evaluate the influence of temperature and humidity on the creep percentage, thickness recovery, and permanent deformation of UD reinforcements prepared with and without phosphorylation. It appears that the creep percentage and permanent deformation are more important for phosphorylated reinforcements than for untreated ones. Increasing the compaction temperature and humidity results in an increase of the creep and permanent deformation of phosphorylated fibres. The tensile strength of phosphorylated fibres‐reinforced composites is lower than that of untreated ones while there is no effect on the tensile modulus. [ABSTRACT FROM AUTHOR]

Contamination of water resources by toxic heavy metals has significant impacts on environmental and human health. Their removal from aqueous media is essential to ensure water sustainability and to provide safe freshwater availability to population. Electrospun chitosan (CS) nonwoven mats are efficient at removing heavy metals from aqueous media. However, they suffer from low permeability and low‐mechanical strength. They are also unable to remove contaminants in a nonselective way. A bilayer sorbent media made of a porous phosphorylated cellulose substrate covered by electrospun CS nanofibers was developed to overcome those weaknesses. The hydrophilic composite shows good water permeability and mechanical strength with appropriate thermal and chemical characteristics. Adsorption tests with Cd(II) indicate that pseudo‐second order and Langmuir models best fitted experimental data, with a maximum adsorption capacity of 591 mg/g at 25°C. Adsorption with multielement samples containing Cr(VI), Cu(II), Cd(II), and Pb(II) also reveal their capability to remove them in a selective way. This mechanically resistant, hydrophilic, and permeable adsorbent media was able to capture both cationic and anionic metallic contaminants. [ABSTRACT FROM AUTHOR]

Porous silicon carbide (SiC) materials were fabricated using the polymer‐derived ceramics method with kraft pulp papers (KPP) and a commercial polycarbosilane, the allylhydridopolycarbosilane (AHPCS), as starting materials. For this, KPP, propargylated KPP, or phosphorylated KPP were used to be impregnated by the AHPCS, with or without Karstedt catalyst. The pyrolysed materials were characterized at different stages, by using thermogravimetric analysis (TGA) coupled with mass spectrometry, X‐ray diffraction (XRD), and scanning electron microscopy (SEM). Depending on the nature of the initial template, various architectured SiC ceramics were successfully obtained with adjustable porosities. The key role of the previous functionalization of the papers was highlighted in terms of interactions at the interface between the polymer and the lignocellulosic handsheets. It led to either replica or sacrificial template methods. Thus, it was possible to tune the open porosity of the porous carbon and β‐SiC materials between 14.8% and 92.9%, with ceramic yields varying from 12% to 71%. [ABSTRACT FROM AUTHOR]