Search

Cu-lean Al-Zn-Mg alloys are known to be susceptible to hydrogen embrittlement (HE), which currently limits their use in automotive industry. Several works suggested that the resulting loss of mechanical properties was related to hydrogen trapping in different metallurgical sites. The present work attempts to provide a better understanding of the hydrogen-dislocations interactions to evaluate their influence on the loss of mechanical properties of hydrogen-embrittled Al-Zn-Mg alloys. Pre-strained samples of 7046 aluminium alloy (AA7046) were therefore prepared in order to increase the density of motionless dislocations. Tensile samples, pre-strained or not, were then corroded in 0.6 M NaCl and mechanically tested to evaluate their HE susceptibility and the role of dislocations on hydrogen diffusion. Results highlighted a significant improvement of the HE resistance of the alloy with the increase in the density of motionless dislocations induced by the pre-strain step. This was attributed to preferential hydrogen trapping on motionless dislocations leading to a decrease in the hydrogen amount in the grain boundaries. The measurements of hydrogen penetration depth by Scanning Kelvin Probe Force Microscopy (SKPFM) for cathodically charged samples provided further evidence to support these assumptions. Keywords: Aluminium alloy, Automotive industry, Hydrogen embrittlement, Hydrogen-dislocation interactions, Hydrogen trapping

The reliability and failure mechanisms of silicide-based thermoelectric modules ( n -type Mg 2 (Si,Sn)/ p -type HMS) were investigated thanks to two types of thermal tests with either a fixed or a cycling thermal gradient, under different atmospheres. The hot interfaces of the thermoelectric modules were analyzed by scanning electron microscopy and X-ray diffraction after the reliability tests. The current thermoelectric modules do not exhibit any failure mechanism under ambient air for a hot side temperature of 250 °C for tests conducted either during 500 h at a fixed temperature gradient or after 1000 thermal cycles. However, when the temperature was increased to 350 °C, pesting phenomena were detected at the hot side of the n -type Mg 2 (Si,Sn) legs caused by the decomposition/oxidation of the material. These phenomena are strongly slowed down for thermoelectric modules tested under a primary vacuum, highlighting the predominant role of oxygen in the degradation mechanism. Interdiffusion phenomena are the most pronounced at the interface of the hot side of the n -type thermoelectric materials. The formation of a MgO layer, which is an electrical and thermal insulator, has decreased the thermoelectric modules' performances. For thermal cycling tests, cracks are observed on the hot side of the n -type legs. The presence of these cracks drastically increases the thermal and electrical resistances, leading to an overheating of the system and limiting its efficiency and failure by breaking electrical continuity. The interfaces at the hot side temperature of the p -type HMS legs remained intact whatever the test conditions were, indicating a high chemical stability and a good mechanical strength.

Background: Septic shock, a leading cause of acute kidney injury, induces release of pro-/anti-inflammatory mediators, leading to increased mortality and poor renal recovery. This is the first in vitro study directly comparing three single-use blood purification devices in terms of removing sepsis-associated mediators and endotoxins., Methods: In vitro hemoperfusion was performed using oXiris ® , CytoSorb ® , and Toraymyxin ® . Heparinized human plasma from healthy volunteers was pre-incubated with pathologic quantities of inflammatory mediators and filtered in a closed-loop circulation model for 2 h. For each device, the removal of 27 inflammatory mediators was measured over time. Endotoxin removal mediated by oXiris and Toraymyxin was assessed using hemoperfusion over 6 h., Results: Endotoxin (lipopolysaccharide) removal was most rapid with Toraymyxin; mean adsorptive clearance over the first 30 min was ~ 20 ml/min vs ~ 8 ml/min with oXiris (p < 0.05). There was minimal endotoxin removal with CytoSorb (1 ml/min). At 120 min, there was no significant difference between the endotoxin removal rates using oXiris (mean ± standard deviation, 68.0 ± 4.4%) and Toraymyxin (83.4 ± 3.8%); both were significantly higher vs CytoSorb (- 6.3 ± 4.9%; p < 0.05). Total removal with oXiris was 6.9 μg vs 9.7 μg for Toraymyxin, where the total lipopolysaccharide quantity introduced was approximately 15.8 μg. Removal rates of pro-/anti-inflammatory cytokines and other inflammatory mediators were similar between oXiris and CytoSorb and were higher with CytoSorb and oXiris vs Toraymyxin. Granulocyte colony-stimulating factor was only effectively adsorbed by CytoSorb (99.4%). Differences were detected between the adsorption mechanism of the devices; binding to oXiris was mainly ionic, while CytoSorb was hydrophobic. No specific protein adsorption was found qualitatively with Toraymyxin., Conclusions: Adsorption rate kinetics varied for individual inflammatory mediators using the three blood purification devices. Mechanisms of adsorption differed between the devices. oXiris was the only device tested that showed both endotoxin and cytokine removal. oXiris showed similar endotoxin adsorption to Toraymyxin and similar adsorption to CytoSorb for the removal of other inflammatory mediators. Differences in device removal capacities could enable treatment to be more tailored to patients.

Atherosclerosis is an important predictor of mortality in patients with chronic kidney disease (CKD) and is associated with a wide inflammatory response. The aim of this study is to evaluate in vitro how different membranes can remove mediators associated with this pathology in a closed loop dialysis model. We performed experimental hemofiltration in vitro using three different membrane materials. Human plasma was preliminarily incubated with various inflammatory mediators and filtered in a closed loop circulation model for 240 min. Respective concentrations of 17 different mediators were measured over time to study the removal mechanisms of each membrane, including associated removal time course. The experiment was repeated three times for the assay of tumor necrosis factor (TNF)-α to document the model variability. Means were compared using Mann-Whitney test. Most of the investigated mediators were effectively removed with the different dialysis membranes. Adsorption mechanism was mainly at the origin of the decrease in mediators circulating concentrations and was maximized in the region 10 000-20 000 Da. Especially, the HeprAN membrane showed fast removal capacities of mediators with elevated isoelectric point including complement factors and chemokines or having basic groups located in the protein periphery, plasminogen activator inhibitor (PAI-1), and TNF-α-like. The latter was further significantly removed with HeprAN and polymethylmethacrylate (PMMA) compared to polyethersulfone (PES) material (P < 0.01). We concluded that dialysis using ionic adsorptive membrane could have a beneficial impact for CKD patients with atherosclerosis and would deserve further clinical investigations., (© 2016 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.)