Search

The results of the studies of the electrochemical synthesis of multilayer graphene oxide were presented, and the possibility of using it as an electrode material of the supercapacitor was shown. In an alcohol suspension the thickness of the particles of multilayer graphene oxide was less than 0.1 μm with an area of more than 100 μm2. The graphene oxide-based electrode has a high specific capacity of 107 F⋅g − 1 and a high charge retention rate of 97% after 5000 cycles. It was shown that the graphene oxide electrode had a maximum specific energy of 8.7 W⋅h⋅kg − 1 at the current density of 0.1 A⋅g − 1 and had a maximum power of 2291.1 W⋅kg − 1 at the current density of 4 A⋅g − 1. The application of a lithium-thionyl chloride cell with a multilayer graphene oxide cathode on a nickel grid was tested. It was found that graphene oxide synthesized using the electrochemical method is a promising electrode material for creating a symmetric supercapacitor.

Three-phase polymer composites are promising materials for creating electronic device components. The qualitative and quantitative composition of such composites has a significant effect on their functional, in particular dielectric properties. In this study, ceramic filler K2Ni0.93Ti7.07O16 (KNTO) with Ag coating as conductive additive (0.5, 1.0, 2.5 wt.%) was introduced into the polyvinylidene difluoride (PVDF) polymer matrix in amounts of 7.5, 15, 22.5, and 30 vol.%. to optimize the dielectric constant and dielectric loss tangent. The filler was characterized by X-ray phase analysis, Fourier-transform infrared spectroscopy and Scanning electron microscopy methods. The dielectric constant, dielectric loss tangent, and conductivity of three-phase composites KNTO@Ag-PVDF were studied in comparison with two-phase composites KNTO-PVDF in the frequency range from 102 Hz to 106 Hz. The dielectric constant values of composites containing 7.5, 15, 22.5, and 30 vol.% filler were 12, 13, 17.4, 19.2 for pure KNTO and 13, 19, 25, 31 for KNTO@Ag filler (2.5 wt.%) at frequency 10 kHz. The dielectric loss tangent ranged from 0.111 to 0.340 at a filler content of 7.5 to 30 vol.%. A significantly enhanced balance of dielectric properties of PVDF-based composites was found with K2Ni0.93Ti7.07O16 as ceramic filler for 1 wt.% of silver. Composites KNTO@Ag(1 wt.%)-PVDF can be applied as dielectrics for passive elements of flexible electronics. [ABSTRACT FROM AUTHOR]

In this paper, LixCa(1−x)Cu3Ti4O12 (LCCTO) solid solutions were successfully synthesized. XRD diagrams showed that dopant acceptor Li+ cations, in a concentration range of x = 0.01–0.10, were successfully merged into CCTO structure. It was found that doping with low concentrations of lithium (x < 0.05) inhibited grain growth during annealing; however, for x > 0.05, the grain growth process resumed. Permittivity and dielectric losses of obtained LCCTO ceramics were analyzed by the means of impedance spectroscopy in a frequency range from 10−1 to 106 Hz. It was revealed that acceptor doping with lithium at an appropriate concentration of x = 0.05 allowed to obtain ceramics with a permittivity level of ε′ = 3 × 104 and low dielectric losses tanδ < 0.1 at 1 kHz. Further addition of lithium in a concentration range of x = 0.075–0.10 led to a sharp decline in permittivity and an increase in dielectric losses. It was discovered that lithium addition to CCTO ceramics drastically decreased grain boundary resistivity from 115 MΩ·cm to 5–40 MΩ·cm at x = 0.01–0.10. Using Havriliak–Negami equation, the relaxation times for grain dipoles and grain boundary dipoles were found to be ranging from 0.8 × 10−6 to 1.7 × 10−6 s and from 0.4 × 10−4 to 7.1 × 10−4 s, respectively. The developed materials can be used in the manufacture of Multilayer Ceramic Capacitors (MLCC) as a dielectric. [ABSTRACT FROM AUTHOR]

In this study, we report the effect of intercalation of dimethyl sulfoxide (DMSO) and urea molecules into the interlayer space of Ti3C2Tx MXene on the dielectric properties of poly(vinylidene fluoride) (PVDF)/MXene polymer nanocomposites. MXenes were obtained by a simple hydrothermal method using Ti3AlC2 and a mixture of HCl and KF, and they were then intercalated with DMSO and urea molecules to improve the exfoliation of the layers. Then, nanocomposites based on a PVDF matrix loading of 5–30 wt.% MXene were fabricated by hot pressing. The powders and nanocomposites obtained were characterized by using XRD, FTIR, and SEM. The dielectric properties of the nanocomposites were studied by impedance spectroscopy in the frequency range of 102–106 Hz. As a result, the intercalation of MXene with urea molecules made it possible to increase the permittivity from 22 to 27 and to slightly decrease the dielectric loss tangent at a filler loading of 25 wt.% and a frequency of 1 kHz. The intercalation of MXene with DMSO molecules made it possible to achieve an increase in the permittivity up to 30 at a MXene loading of 25 wt.%, but the dielectric loss tangent was increased to 0.11. A discussion of the possible mechanisms of MXene intercalation influence on the dielectric properties of PVDF/Ti3C2Tx MXene nanocomposites is presented. [ABSTRACT FROM AUTHOR]

Some solid solutions with the chemical composition KxFeyTi8-yO16 (KFTO) and a hollandite-like structure were successfully synthesized by modified sol–gel method. The obtained powders were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The ceramic pellets based on KFTO powders were obtained by compressing and sintering at 1080 °C for 4 h. The sinters were characterized by X-ray and impedance spectroscopy. XRD results show that KFTO powders have a mono-phase tetragonal structure at x = 1.4–1.8 and y = 1.4–1.6. However, it was recognized that the hollandite-like phase could be broken during sintering to form TiO2 and Fe2TiO5 crystals distributed throughout the volume of the ceramics. A frequency dependency of dielectric properties for the sinters was studied by impedance spectroscopy. It was found that an increase in the TiO2 (rutile) phase during the sintering contributes to a decrease in dielectric losses. At the same time, the KFTO ceramics with reduced content of potassium had increased permittivity. The contribution of electron-pinned defect dipoles (EPDD) and internal barrier layer capacitance (IBLC) in the permittivity of the obtained ceramics was estimated using the Havriliak–Negami equation. It is shown that the KFTO ceramics have the polydisperse characteristic of dielectric relaxation. The observed grain and grain boundary dipole relaxation times were 1.03 × 10−6 to 5.51 × 10−6 s and 0.197 to 0.687 s, respectively. [ABSTRACT FROM AUTHOR]

New three-phase composites, destined for application as dielectrics in the manufacturing of passive elements of flexible electronics, and based on polymer (PVDF) matrix filled with powdered ceramics of the hollandite-like (KFTO(H)) structure (5.0; 7.5; 15; 30 vol.%) and carbon (MWCNT) additive (0.5; 1.0; 1.5 wt.% regarding the KFTO(H) amount), were obtained and studied by XRD, FTIR and SEM methods. Chemical composition and stoichiometric formula of the ceramic material synthesized by the sol–gel method were confirmed with the XRF analysis data. The influence of the ceramic and carbon fillers on the electrical properties of the obtained composites was investigated using impedance spectroscopy. The optimal combination of permittivity and dielectric loss values at 1 kHz (77.6 and 0.104, respectively) was found for the compositions containing K1.6Fe1.6Ti6.4O16 (30 vol.%) and MWCNTs (1.0 wt.% regarding the amount of ceramic filler). [ABSTRACT FROM AUTHOR]

In this work, polymer matrix composites with the compositions PTFE/KFTO(H) and PTFE/KFTO(H)@CB and with filler volume fractions of 2.5, 5.0, 7.5, 15, and 30% (without and with carbon modification at a content of 2.5 wt.% regarding ceramic material) were produced by calendering and hot pressing and studied using FTIR, SEM, and impedance spectroscopy methods. Ceramic filler (KFTO(H)) was synthesized using the sol–gel Pechini method. Its structure was investigated and confirmed by the XRD method with following Rietveld refinement. The carbon black (CB) modification of KFTO(H) was carried out through the calcination of a mixture of ceramic and carbon materials in an argon atmosphere. Afterwards, composites producing all the components' structures weren't destroyed according to the FTIR results. The effect of carbon additive at a content of 2.5 wt.% relating to ceramic filler in the system of polymer matrix composites was shown, with permittivity increasing up to ε' = 28 with a simultaneous decrease in dielectric loss (tanδ < 0.1) at f = 103 Hz for composites of PTFE/KFTO(H)@CB (30 vol.%). [ABSTRACT FROM AUTHOR]

Polymethyl methacrylate/hollandite‐like copper doped potassium titanate high‐k ceramics composites with different filler content (20–60 vol.%) are prepared by simple method of mixing of the polymer solution and ceramics dispersion followed evaporation of the solvent and hot pressing. The particle morphology and size are estimated by SEM. The composites obtained are studied by XRD, FTIR, and TGA methods. The influence of the additive and the concentration of hollandite‐like copper doped potassium titanate high‐k ceramics on dielectric properties (permittivity, conductivity, dielectric loss tangent) are investigated at frequency range from 10−1 to 106 Hz. It is shown that the increasing of ceramics concentration cause the increasing of main dielectric characteristics, namely permittivity up to 40 and dielectric loss up to 0.13 at 60 vol.% of filler and 0.1 Hz. Conductivity percolation threshold for PMMA/KCTO(H) composites was estimated (vc = 0.0773 vol. [20.9 wt. %]). Experimental data on permittivity are compared with different theoretical models (Lichtenecker's model and the Effective Medium Theory model). [ABSTRACT FROM AUTHOR]

Polymer matrix composites based on ED-20 epoxy resin, hollandite K1.6(Ni0.8Ti7.2)O16 and carbon nanotubes with a variable content of 0.107; 0.213 and 0.425 vol.% were obtained for the first time. Initial components and composites produced were characterized by XRD, XRA, FTIR, SEM and Raman spectroscopy. The dielectric properties of composite materials were measured by impedance spectroscopy and determined by the volume ratio of the composite components, primarily by the concentration of CNTs. At a CNT content of 0.213 vol.% (before percolation threshold), the maximum synergistic effect of carbon and ceramic fillers on the dielectric properties of a composite based on the epoxy resin was found. Three-phase composites based on epoxy resin, with a maximum permittivity at a minimum dielectric loss tangent, are promising materials for elements of an electronic component base. [ABSTRACT FROM AUTHOR]