Search

This work compares the overall performance and biogas production of continuous and intermittent UASB (Upflow Anaerobic Sludge Blanket) reactors treating dairy wastewater and subjected to fat, hydraulic and temperature shocks. The systems were monitored for methane production, effluent concentration, volatile fatty acids, and microbial populations of the Eubacteria, Archaea and Syntrophomonadaceae groups. This last microbial group has been reported in literature as being determinant for the degradation of fatty substrates present in the wastewater and subsequent biogas production. Results show that both continuous and intermittent systems supported the applied shocks. However, the intermittent systems exhibited better performance than the continuous systems in biogas production and physical-chemical parameters. Syntrophomonadaceae microbial group was present in the intermittent systems, but was not detected in the biomass from the continuous systems. Hydraulic and temperature shocks, but not the fat shock, caused severe losses in the relative abundance of the Syntrophomonadaceae group in intermittent systems, leading to undetectable levels during the temperature shock. The severity of the effects of the applied shocks on the key microbial group Syntrophomonadaceae, were classified as: fats < hydraulic < temperature. Results from a full-scale anaerobic reactor confirm the effect of intermittent operation on the presence of Syntrophomonadaceae and the effect on reactor performance. [ABSTRACT FROM AUTHOR]

Recently, wood pellets have become a reliable and clean renewable fuel for residential heating, replacing fossil fuels and reducing greenhouse gas emissions. Wood pellets are normally produced in industrial pellet plants (centralised production), but decentralised small-scale local production also occurs. This study applies Life Cycle Assessment (LCA) to quantify and compare the environmental profile of one centralised and two decentralised alternatives for wood pellet production for residential heating in Portugal: (1) industrial wood pellets production (centralised), (2) wood pellets production at sawmills (decentralised) and (3) wood pellets production at households (decentralised). System boundaries include the stages of forest management, wood pellet production, wood pellet distribution and wood pellet energetic conversion. The impact results show that industrial pellet production ranks as the worst alternative, while pellet production at households has the best environmental profile for all the impact categories under study. However, the environmental impacts of pellet production at the sawmill do not differ greatly from those of the pellet production at households; they are 14 to 16% higher for global warming and fossil resources scarcity and 0.3 to 3% higher for the remaining impact categories. The worst environmental performance of the industrial pellet production alternative is mainly due to high electricity and diesel consumption during wood pellet production and the use of logging residues to generate heat for drying biomass feedstock. A sensitivity analysis was performed to evaluate the influence of changing the distance travelled during the transport of packed pellets to stores and sawdust to households. The results show changes in the environmental performance ranking, highlighting that for short distances, both decentralised alternatives can be more sustainable from an environmental perspective than the centralised alternative, but for larger distances, the pellet production at households should be avoided., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

The increasing use of forest biomass as a fuel for power plants due to environmental concerns will certainly increase the amount of woody biomass ash produced. Because of the environmental problems derived from woody biomass ash disposal, an important aspect for the sustainable development of the energy sector is the implementation of effective ash management strategies. The purpose of this study is to assess the environmental impacts of woody biomass ash landfarming for soil amelioration through a Life Cycle Assessment. The baseline scenario corresponds to the current most common practice of woody biomass ash management (landfilling), and two different landfarming alternatives were assessed: liming and fertilisation. Credits were given to the system due to the substitution of three traditional liming products and five traditional fertilisers. Woody biomass ash landfarming presented satisfactory performance in five impact categories under study in comparison to landfilling. When woody biomass ash was used for liming, the environmental savings were more pronounced when substituting hydrated lime. For potassium supply, the substitution of potassium nitrate by woody biomass ash presented the best environmental performance, while for phosphorus supply, the environmental savings were more pronounced substituting single superphosphate. However, in four impact categories, the environmental impacts of ash landfarming exceeded the impacts of ash landfilling, due to the emission to soil of nutrients and trace elements to soil. But this does not necessarily imply increased risks for the environment, as the potential pollutants leaching depends on their bioavailability in the soil., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

Wood-fuelled systems are commonly used all over the world for residential heating, and recently wood pellets have been replacing traditional firewood. This article presents an environmental life cycle assessment of five wood-based combustion systems for residential heating: i) a pellet stove using maritime pine pellets; a wood stove using ii) eucalyptus (Eucalyptus globulus Labill.) and iii) maritime pine (Pinus pinaster Ait.) split logs; and a fireplace using iv) eucalyptus and v) maritime pine split logs. The functional unit is 1 MJ of thermal energy for residential heating. System boundaries include four stages: (1) forest management; (2) pellet and wood split log production; (3) distribution; and (4) thermal energy generation. Environmental impacts were calculated for seven impact categories from the ReCiPe 2016 midpoint method, and a sensitivity analysis was performed using the Product Environmental Footprint (PEF) life cycle impact assessment method and modifying the distances travelled. Of the five heating systems analysed, the fireplace presents the worst performance for all the impact categories with the exception of freshwater eutrophication and marine eutrophication, when maritime pine split logs are burned in the fireplace. Comparing the pellet stove with the wood stove, neither system is better for all the impact categories analysed. Regarding sensitivity analysis, the use of an alternative characterisation method leads to similar trends in the results in comparison with those obtained from the ReCiPe method, while changes in transport distances do not affect the total impacts to a large extent., (Copyright © 2019 Elsevier B.V. All rights reserved.)

The development of methods to assess the potential environmental impact of green water consumption in life cycle assessment has lagged behind those for blue water use, which are now routinely applied in industrial and policy-related studies. This represents a critical gap in the assessment of land-based production systems and the ability to inform policy related to the bio-economy. Combining satellite remote sensing and meteorological data sets, this study develops two new sets of spatially-differentiated and globally applicable characterisation factors (CFs) to assess the environmental impact of green water flows in LCA. One set of CFs addresses the impact of shifts in water vapour flow by evapotranspiration on blue water availability (CFWS) and the other set of CFs addresses moisture recycling within a basin (CFWA). Furthermore, as an additional and optional step, these two indicators are combined into an aggregated green water scarcity indicator, representing the global variability of green water scarcity. The values obtained for CFWA show that there are significant changes in green water flows that were returned to the atmosphere in Alaska (covered by open shrublands) and in some central regions of China (covered by grasslands and barren or sparsely vegetated land), where precipitation levels are lower than 10 mm/yr. The results obtained for CFWS indicate that severe perturbations in surface blue water production occur, particularly in central regions of China (covered by grasslands), the southeast of Australia (covered by evergreen broadleaf forest) and in some central regions of the USA (covered by grassland and evergreen needleleaf forest). The application of the green water scarcity CFs enables the evaluation of the potential environmental impact due to green water consumption by agricultural and forestry products, informing both technical and non-technical audiences and decision-makers for the purpose of strategic planning of land use and to identify green water protection measures., (Copyright © 2018 Elsevier B.V. All rights reserved.)

In the present study, a simulation model for the calculation of the carbon footprint of the cork oak sector (CCFM) is developed for the first time. A life cycle approach is adopted including the forest management, manufacturing, use and end-of-life stages. CCFM allows the user to insert the cork type used as raw material and its respective quantity and the distances in-between the various stages. The user can choose among different end-of-life destination options for the used cork products. The option of inserting different inputs, allows the use of the present simulation model for different cork oak systems, in different countries and with different conditions. CCFM allows the identification of the stages and products with the greatest carbon footprint and thus, a better management of the sector from an environmental perspective. The Portuguese cork oak sector is used as an application example of the model. The results obtained showed that the agglomeration industry is the hotspot for the carbon footprint of the cork sector mainly due to the production of the resins that are mixed with the cork granules for the production of agglomerated cork products. The consideration of the biogenic carbon emissions and sequestration of carbon at the forest in the carbon footprint, resulted to a great decrease of the sector's carbon footprint. Future actions for improvement are suggested in order to decrease the carbon footprint of the entire cork sector. It was found that by decreasing by 10% the emission factor of the agglomeration and transformation industries, substituting the transport trucks by more recent ones and by decreasing by 10% the cork products reaching the landfilling end-of-life destinations (while increasing the quantities reaching incineration and recycling), a decrease of the total CF (excluding the biogenic emissions and sequestration) of the entire cork industry by 10% can be achieved., (Copyright © 2016 Elsevier B.V. All rights reserved.)

This work studied the influence of effluent recirculation upon the kinetics of anaerobic degradation of dairy wastewater in the feedless phase of intermittent upflow anaerobic sludge bed (UASB) reactors. Several laboratory-scale tests were performed with different organic loads in closed circuit UASB reactors inoculated with adapted flocculent sludge. The data obtained were used for determination of specific substrate removal rates and specific methane production rates, and adjusted to kinetic models. A high initial substrate removal was observed in all tests due to adsorption of organic matter onto the anaerobic biomass which was not accompanied by biological substrate degradation as measured by methane production. Initial methane production rate was about 45% of initial soluble and colloidal substrate removal rate. This discrepancy between methane production rate and substrate removal rate was observed mainly on the first day of all experiments and was attenuated on the second day, suggesting that the feedless period of intermittent UASB reactors treating dairy wastewater should be longer than one day. Effluent recirculation expressively raised the rate of removal of soluble and colloidal substrate and methane productivity, as compared with results for similar assays in batch reactors without recirculation. The observed bed expansion was due to the biogas production and the application of effluent recirculation led to a sludge bed contraction after all the substrates were degraded. The settleability of the anaerobic sludge improved by the introduction of effluent recirculation this effect being more pronounced for the higher loads.

Life Cycle Assessment (LCA) has become a common methodology to evaluate the environmental performance of forest systems in recent years. This study aims to estimate the environmental profile associated with maritime pine wood production in two representative European countries: Portugal and France. Different forest management regimes based on low and high intensive conditions were evaluated and differences in logging equipment, biomass yield and lifespan were also reported. The study was completed with a sensitivity analysis based on two allocation approaches (economic and volumetric) since biomass from thinning processes is harvested and can be used as a co-product. The production of maritime pine in Portugal under low intensity conditions should present the best environmental results with reductions of 50-94% in comparison with the worst scenario. It is mainly associated with the absence of forest activities in periods previous to the logging stage. French intensive forest scenario ranks as the second best alternative of pine wood production. The remaining scenarios reported worse results in terms of environmental impacts mostly due to the remarkable repetition of a selection of those forest activities with large fuel requirement (mainly on site preparation and stand establishment and tending). Regardless of the scenario, logging related activities such as final cutting and forwarding were identified as the hotspots mainly due to the fuel requirements. Fertilizer production (if required), thinning and cleaning processes reported also remarkable contributions to the categories under assessment. In addition, an economic estimation for each forest management scenario has been performed mainly considering fuel, machinery and labor costs. According to the results, the Portuguese low intensive scenario is the best choice together with the French intensive scenario under an economic point of view because of the lowest production costs per functional unit. Activities related with the logging stage have also been identified as economic hotspots., (Copyright © 2013 Elsevier B.V. All rights reserved.)

Cork forest systems are responsible for making an important economic contribution to the Mediterranean region, especially Portugal where the cork oak woodlands or montados contain about 32% of the world's area. The environmental profile derived from reproduction cork production and extraction in two Portuguese regions (Tagus valley and Alentejo) representative of the Portuguese sector were assessed in detail using the Life-Cycle Assessment (LCA) methodology from a cradle-to-gate perspective. The production line was divided into four stages considering all the processes involved: stand establishment, stand management, cork stripping and field recovery. According to the environmental results, there were remarkable differences between the two production scenarios mainly due to the intensity and repetition of forest activities even though the cork yield was reported to be the same. The management system in the Alentejo region presented the worse environmental profile in almost all the impact categories under assessment, mainly due to the shorter cycle duration of the mechanical cleaning and pruning processes. Cork stripping was identified in both scenarios as the production stage with the highest contribution to the environmental profile due to the cleaning and pruning processes. A sensitivity assessment concerning the cork yield was performed since the average production yields in the Portuguese montados are lower than the ones used in this study. Thus, if the cork yield is reduced, the environmental profile in both scenarios gets worse since almost all the forest activities involved are the same., (Copyright © 2013 Elsevier B.V. All rights reserved.)

Milk and dairy products constitute an important ingredient in the human diet. Ultra-high temperature (UHT) milk is the main dairy product consumed in Portugal and its production entails large inputs of resources which derive on negative environmental effects such as nutrient enrichment of the ecosystem and climate change. In this study, Life Cycle Assessment (LCA) methodology was considered for the environmental assessment of packaged UHT milk produced in Portugal, including simple (whole, semi-skimmed and skimmed) and cocoa milk from a cradle-to-gate perspective and to identify the environmental hot spots. Results showed that the production of the raw milk in the dairy farm is the main hot spot in almost all the categories under assessment mainly due to the emissions from enteric fermentation, manure management and fertilisers production and application. Furthermore, on-site emissions derived from dairy factory are remarkable together with the packages and energy requirements production. The values reported in this study are in the range of other related papers. However, differences were also identified due to several reasons such as allocation approach, data sources, characterisation factors, farm management regimes and assumptions considered. Therefore, these aspects should be carefully addressed and sensitivity to the assumptions and uncertainty of the results should be evaluated., (Copyright © 2012 Elsevier B.V. All rights reserved.)

Failures in stability and COD removal performance often occurred in full-scale anaerobic reactors treating the evaporator condensate from a sulphite pulp mill due to substrate inhibition and occasional contaminations with red liquor (wood cooking liquor). With this work, the beneficial effect provided by the continuous addition of an external carbon source (sugarcane molasses) on the overall performance and stability of the biological process was evaluated. With a moderate addition of molasses the inhibition was mitigated which led to an increase of the COD removal rate from 52% to 77% and a methane production increase from 460 to 1650mld(-1) at an organic loading rate of 2.61g CODl(-1)d(-1). A similar conclusion can be drawn for the case when contamination with red liquor occurs. These results suggest that sugarcane molasses addition may be regarded as a low-cost operational strategy for the anaerobic treatment of sulphite evaporator condensate.

Recent environmental concerns have prompted a re-evaluation of conventional management strategies and refueled the search of innovative waste management practices. In this sense, the anaerobic digestion of both fat and the remaining complex organic matter present in dairy wastewaters is attractive, although the continuous operation of high rate anaerobic processes treating this type of wastewaters causes the failure of the process. This work accesses the influence of non-feeding period length on the intermittent operation of mesophilic UASB reactors treating dairy wastewater, in order to allow the biological degradation to catch up with adsorption phenomenon. During the experiments, two UASB reactors were subject to three organic loading rates, ranging from 6 to 12 g(COD) x L(-1) x d(-1), with the same daily load applied to both reactors, each one with a different non-feeding period. Both reactors showed good COD removal efficiencies (87-92%). A material balance for COD in the reactors during the feeding and non-feeding periods showed the importance of the feedless period, which allowed the biomass to degrade substrate that was accumulated during the feeding period. The reactor with the longest non-feeding period had a better performance, which resulted in a higher methane production and adsorption capacity for the same organic load applied with a consequent less accumulation of substrate into the biomass. In addition, both reactors had a stable operation for the organic load of 12 g(COD) x L(-1) x d(-1), which is higher than the maximum applicable load reported in literature for continuous systems (3-6 g(COD) x L(-1) x d(-1))., ((c) 2006 Wiley Periodicals, Inc.)