Search

Spontaneous locking of the phase of a coherent phonon source to an external reference is demonstrated in a deeply sideband-unresolved optomechanical system. The high-amplitude mechanical oscillations are driven by the anharmonic modulation of the radiation pressure force that result from an absorption-mediated free-carrier/temperature limit cycle, i.e., self-pulsing. Synchronization is observed when the pump laser driving the mechanical oscillator to a self-sustained state is modulated by a radiofrequency tone. We employ a pump-probe phonon detection scheme based on an independent optical cavity to observe only the mechanical oscillator dynamics. The lock range of the oscillation frequency, i.e., the Arnold tongue, is experimentally determined over a range of external reference strengths, evidencing the possibility to tune the oscillator frequency for a range up to 350 kHz. The stability of the coherent phonon source is evaluated via its phase noise, with a maximum achieved suppression of 44 dBc/Hz at 1 kHz offset for a 100 MHz mechanical resonator. Introducing a weak modulation in the excitation laser reveals as a further knob to trigger, control and stabilize the dynamical solutions of self-pulsing based optomechanical oscillators, thus enhancing their potential as acoustic wave sources in a single-layer silicon platform.

Nanocrystalline materials exhibit properties that can differ substantially from those of their single crystal counterparts. As such, they provide ways to enhance and optimize their functionality for devices and applications. Here, we report on the optical, mechanical and thermal properties of nanocrystalline silicon probed by means of optomechanical nanobeams to extract information of the dynamics of optical absorption, mechanical losses, heat generation and dissipation. The optomechanical nanobeams are fabricated using nanocrystalline films prepared by annealing amorphous silicon layers at different temperatures. The resulting crystallite sizes and the stress in the films can be controlled by the annealing temperature and time and, consequently, the properties of the films can be tuned relatively freely, as demonstrated here by means of electron microscopy and Raman scattering. We show that the nanocrystallite size and the volume fraction of the grain boundaries play a key role in the dissipation rates through nonlinear optical and thermal processes. Promising optical (13,000) and mechanical (1700) quality factors were found in the optomechanical cavity realized in the nanocrystalline Si resulting from annealing at 950°C. The enhanced absorption and recombination rates via the intragap states and the reduced thermal conductivity boost the potential to exploit these nonlinear effects in applications including Nanoelectromechanical systems (NEMS), phonon lasing and chaos-based devices.

In this paper we describe the design and development of interconnected devices which allow monitoring in situ the performance of solar boilers. This mobile remote lab system comprises two huge blocks of hardware: a mobile station located by the boiler, which is monitored and controlled in a remote way, and a fixed station, located in the Laboratory of Energy for the Sustained Development of the Universidad Nacional de Rosario. The communication between the fixed and mobile devices is controlled by micro-controllers included in both stations and programmed in C language. The project is being developed through three parallel lines of work: 1) Design and development of fixed and mobile hardware; 2) Development of firmware and software necessary to register and communicate data; 3) Design and development of learning activities. This mobile remote lab will be useful to test the behavior of solar boilers in the place and environmental conditions where they are placed so as to evaluate their performance and efficiency anywhere. This is also in order to contribute for the implementation of norms for the certification of solar boilers. On the other hand, the data and results obtained from the development will be used as supplies for the design of learning activities. [ABSTRACT FROM AUTHOR]

Purpose: Stereotactic body radiotherapy (SBRT) has become an excellent non-invasive alternative for many patients with primary renal cell carcinoma (RCC) and adrenal malignancies (AM). The aims of this study were to analyse how tumor-, patient- and treatment-related factors may influence the outcomes and side effects of SBRT and to assess its benefits as an alternative to surgery., Methods: This retrospective, multicenter study included 25 lesions in 23 patients treated with SBRT using different devices (LINAC, CyberKnife ® and Tomotherapy ® ). A multivariate linear regression was used for the statistical study., Results: Local control time was higher than six months in more than 87% of patients and treatment response was complete for 73.68%. There was an overall 2-year survival of 40% and none of the deaths were secondary to renal or adrenal local progression. Patients treated with lower total radiation dose (mean [m] = 55 Gy) but less fractions with more dose per fraction (> 8.5 Gy) showed better outcome. Patients with previous chemotherapy and surgery treatments also showed higher complete response and disease-free survival (> 6 months)., Conclusions: This study highlights the importance of ultra-hypofractionated regimens with higher doses per session. Thus, the referral of patients with RCC and AM to Radiotherapy and Oncology departments should be encouraged supporting the role of SBRT as a minimally invasive and outpatient treatment., (© 2024. The Author(s).)

Despite tremendous progress in research on self-assembled nanotechnological building blocks, such as macromolecules 1 , nanowires 2 and two-dimensional materials 3 , synthetic self-assembly methods that bridge the nanoscopic to macroscopic dimensions remain unscalable and inferior to biological self-assembly. By contrast, planar semiconductor technology has had an immense technological impact, owing to its inherent scalability, yet it seems unable to reach the atomic dimensions enabled by self-assembly. Here, we use surface forces, including Casimir-van der Waals interactions 4 , to deterministically self-assemble and self-align suspended silicon nanostructures with void features well below the length scales possible with conventional lithography and etching 5 , despite using only conventional lithography and etching. The method is remarkably robust and the threshold for self-assembly depends monotonically on all the governing parameters across thousands of measured devices. We illustrate the potential of these concepts by fabricating nanostructures that are impossible to make with any other known method: waveguide-coupled high-Q silicon photonic cavities 6,7 that confine telecom photons to 2 nm air gaps with an aspect ratio of 100, corresponding to mode volumes more than 100 times below the diffraction limit. Scanning transmission electron microscopy measurements confirm the ability to build devices with sub-nanometre dimensions. Our work constitutes the first steps towards a new generation of fabrication technology that combines the atomic dimensions enabled by self-assembly with the scalability of planar semiconductors., (© 2023. The Author(s).)

The quality factor, Q , of photonic resonators permeates most figures of merit in applications that rely on cavity-enhanced light-matter interaction such as all-optical information processing, high-resolution sensing, or ultralow-threshold lasing. As a consequence, large-scale efforts have been devoted to understanding and efficiently computing and optimizing the Q of optical resonators in the design stage. This has generated large know-how on the relation between physical quantities of the cavity, e.g., Q , and controllable parameters, e.g., hole positions, for engineered cavities in gaped photonic crystals. However, such a correspondence is much less intuitive in the case of modes in disordered photonic media, e.g., Anderson-localized modes. Here, we demonstrate that the theoretical framework of quasinormal modes (QNMs), a non-Hermitian perturbation theory for shifting material boundaries, and a finite-element complex eigensolver provide an ideal toolbox for the automated shape optimization of Q of a single photonic mode in both ordered and disordered environments. We benchmark the non-Hermitian perturbation formula and employ it to optimize the Q-factor of a photonic mode relative to the position of vertically etched holes in a dielectric slab for two different settings: first, for the fundamental mode of L3 cavities with various footprints, demonstrating that the approach simultaneously takes in-plane and out-of-plane losses into account and leads to minor modal structure modifications; and second, for an Anderson-localized mode with an initial Q of 200, which evolves into a completely different mode, displaying a threefold reduction in the mode volume, a different overall spatial location, and, notably, a 3 order of magnitude increase in Q ., Competing Interests: The authors declare no competing financial interest., (© 2023 The Authors. Published by American Chemical Society.)

We design and fabricate a grating coupler for interfacing suspended silicon photonic membranes with free-space optics while being compatible with single-step lithography and etching in 220 nm silicon device layers. The grating coupler design simultaneously and explicitly targets both high transmission into a silicon waveguide and low reflection back into the waveguide by means of a combination of a two-dimensional shape-optimization step followed by a three-dimensional parameterized extrusion. The designed coupler has a transmission of -6.6 dB (21.8 %), a 3 dB bandwidth of 75 nm, and a reflection of -27 dB (0.2 %). We experimentally validate the design by fabricating and optically characterizing a set of devices that allow the subtraction of all other sources of transmission losses as well as the inference of back-reflections from Fabry-Pérot fringes, and we measure a transmission of 19 % ± 2 %, a bandwidth of 65 nm and a reflection of 1.0 % ± 0.8 %.

Nanophononics has the potential for information transfer, in an analogous manner to its photonic and electronic counterparts. The adoption of phononic systems has been limited, due to difficulties associated with the generation, manipulation, and detection of phonons, especially at GHz frequencies. Existing techniques often require piezoelectric materials with an external radiofrequency excitation that are not readily integrated into existing CMOS infrastructures, while nonpiezoelectric demonstrations have been inefficient. In this Letter, we explore the optomechanical generation of coherent phonons in a suspended 2D silicon phononic crystal cavity with a guided mode around 6.8 GHz. By incorporating an air-slot into this cavity, we turn the phononic waveguide into an optomechanical platform that exploits localized photonic modes resulting from inherent fabrication imperfections for the transduction of mechanics. Such a platform exhibits very fine control of phonons using light, and is capable of coherent self-sustained phonon generation around 6.8 GHz, operating at room temperature. The ability to generate high frequency coherent mechanical vibrations within such a simple 2D CMOS-compatible system could be a first step towards the development of sources in phononic circuitry and the coherent manipulation of other solid-state properties.