Search

The intrinsic mechanical properties of single‐grain RE‐Ba‐Cu‐O bulk high‐temperature superconductors can be improved by employing a thin‐wall geometry. This is where the samples are melt‐processed with a predefined network of artificial holes to decrease the effective wall thickness. In this study, the tensile strengths of thin‐wall YBCO disks were determined using the Brazilian test at room temperature. Compared with conventional single grain YBCO disks, the thin‐wall YBCO disks displayed an average tensile strength that is 93% higher when the holes were filled with Stycast epoxy resin. This implies a thin‐wall sample should, in theory, be able to sustain a trapped field that is 39% higher without exceeding the mechanical limit of the sample. High‐field magnetization experiments were performed by applying magnetization fields of up to 11.5 T, specifically to break the samples in order to verify the effect of increased mechanical strength (and improved cooling) on the ability of bulk (RE)BCO to trap field successfully. The standard YBCO sample failed when it was magnetized with a field of 10 T at 35 K, suffering permanent damage. As a result, the standard sample could only trap a maximum surface field of 7.6 T without failure. On the other hand, the thin‐wall YBCO sample survived all magnetization cycles, including a maximum magnetization field of 11.5 T at 35 K, demonstrating a greater intrinsic ability to withstand significantly higher electromagnetic stresses. By subsequently field‐cooling the thin‐wall sample with 11 T at 30 K, a surface field of 8.8 T was trapped successfully without requiring any external ring reinforcement.

Osteoporosis is a skeletal disease characterized by bone loss and bone microarchitectural deterioration. The combination of smart materials and stem cells represents a new therapeutic approach. In the present study, highly porous scaffolds are prepared by combining the conducting polymer PEDOT:PSS with collagen type I, the most abundant protein in bone. The inclusion of collagen proves to be an effective way to modulate their mechanical properties and it induces an increase in scaffolds’ electrochemical impedance. The biomimetic scaffolds support neural crest-derived stem cell osteogenic differentiation, with no need for scaffold pre-conditioning contrarily to other reports.

The magnitude of the maximum trapped magnetic field in a bulk, single-grain superconductor is a key performance figure of merit. This is determined, generally, by the magnitude of the critical current density, J c , and the length scale over which it flows. As with all type-II superconductors, J c is related closely to the microstructure of the superconducting material and, in the case of RE–Ba–Cu–O [(RE)BCO, where RE is a rare-earth element or yttrium] single grains, RE2BaCuO5 (RE-211) inclusions in the superconducting REBa2Cu3O7−δ (RE-123) phase matrix are key microstructural features that act effectively as flux pinning centres. Although the distribution of RE-211 in single-grain bulk superconductors has been studied extensively, the variation of J c within a given sample has been much investigated much less thoroughly. A detailed experimental understanding of the variation of J c in these technologically important materials, therefore, is required given the growing popularity and significance of numerical techniques for modelling the behaviour of type-II bulk superconductors. Here we report a systematic investigation of the correlation between Gd-211 particle density and sample porosity, which are microstructural features, and T c and J c in a Gd–Ba–Cu–O bulk, single grain fabricated using a buffer layer and a supply of additional liquid phase. This was performed by cutting the sample into numerous sub-specimens of approximate dimensions 1.8 × 2.8 × 1.5 mm3. We observe that J c decreases with distance from the seed, although more strongly with distance along the c-axis than along the a–b plane. In contrast to what might be expected given the assumed contribution of RE-211 inclusions to flux pinning, we find no evidence of a clear correlation between the local RE-211 precipitate density and local critical current on a length scale of mm. We observe that the porosity of the sample is a more dominant factor in determining the distribution of J c within a single grain.

Superconducting bulks, acting as high-field permanent magnets, are promising for many applications. An important effect in bulk permanent magnets is crossed-field demagnetization, which can reduce the magnetic field in superconductors due to relatively small transverse fields. Crossed-field demagnetization has not been studied in sample shapes such as rectangular prisms or cubes. This contribution presents a study based on both three-dimensional (3-D) numerical modeling and experiments. We study a cubic Gd-Ba-Cu-O bulk superconductor sample of size 6 mm magnetized by field cooling in an external field of around 1.3 T, which is later submitted to crossed-field magnetic fields of up to 164 mT. Modeling results agree with experiments, except at transverse fields 50% or above of the initial trapped field. The current paths present a strong 3-D nature. For instance, at the midplane perpendicular to the initial magnetizing field, the current density in this direction changes smoothly from the critical magnitude, Jc, at the lateral sides to zero at a certain penetration depth. This indicates a rotation of the current density with magnitude Jc, and hence force free effects like flux cutting are expected to play a significant role., The work of M. Kapolka was supported in part by the Research and Development Operational Programme funded by the ERDF under Project SIVVP, ITMS 26230120002 for the use of computing resources, and in part by the Grant Agency of the Ministry of Education of the Slovak Republic and the Slovak Academy of Sciences (VEGA) under Contract 2/0126/15. The work of M. Ainslie was supported in part by the Royal Academy of Engineering Research Fellowship and in part by the Engineering and Physical Sciences Research Council Early Career Fellowship EP/P020313/1.

REBa 2 Cu 3 O 7-δ bulk superconductors are able to trap large magnetic fields and as a result they have potential to work as strong magnets. In this study, highly textured yttrium, gadolinium, and samarium based cuprate bulk superconductors were prepared using conventional top-seeded melt-textured growth, and magnetized by employing both field-cooling magnetization (FCM) and pulsed-field magnetization (PFM) techniques at 77 K. The same peak value of a trapped field was achieved using FCM and PFM, which means all the bulk samples were fully magnetized by using the PFM method. In addition, the magnitude of the pulsed field required to fully magnetize the bulk samples varied with rare-earth element in the (RE)BCO formulation.

The widespread use of ceramic (RE)Ba 2 Cu 3 O 7 bulk superconductors (RE-123), where RE = Y, Gd, or Sm, is generally hindered by their poor mechanical properties. While a large number of techniques can be used to improve the mechanical properties of conventional ceramic materials, many of these are incompatible with the growth of single grain, bulk RE-123 superconductors using the top seeded melt growth (TSMG) process. Complications arise due to the need to minimize the degradation of the superconducting properties and produce a single-grained sample. Nonetheless, the addition of Ag to RE-Ba-Cu-O [(RE)BCO] precursor powder has been demonstrated to be effective in improving the mechanical properties of single grain bulk superconductors fabricated by TSMG without deleterious effects on performance. Although large single grains of GdBa 2 Cu 3 O 7 -Ag and SmBa 2 Cu 3 O 7 -Ag have been successfully and reliably grown, it has proven more difficult to grow large single grains of YBa 2 Cu 3 O 7 -Ag. We recently demonstrated the growth of single grain YBa 2 Cu 3 O 7 -Ag bulk superconductors that exhibit relatively good superconducting properties. In this work, we report the flexural stress at a number of locations within YBa 2 Cu 3 O 7 single grains grown by TSMG with and without additional liquid phase and with silver addition. In addition, we have compared the distribution of the failure stress with the pore and silver distribution.

In this work, a series of melt processed Y Ba Cu O (YBCO) single-grains have been fabricated by the top-seeded melt growth (TSMG) technique. The melt processing is accepted widely as an effective way to grow bulk, single grain YBCO superconductors; however, this process is extremely complex and every step can affect the final properties of prepared bulk. Therefore, the impact of precursor powder preparation and growth conditions was studied for the first time. Cost-effective in-house made powder and commercially available precursor powders were employed and samples were grown employing top seeded melt growth, following the isothermal and the under-cooling growth techniques. The bulk microstructure including Y2BaCuO5 (Y-211) particle size and distribution, superconducting properties (Tc, Jc) and field trapping potential were investigated. The cost-effective high performance batch processing methodology was optimized. The fabricated YBCO bulks (diameter of 28 mm) exhibited average trapped field of 0.85 T at 77 K. Furthermore, other possibilities to achieve advancement in processing (RE)BCO bulks, are proposed.

A robust and reliable in-situ magnetization method is essential for exploiting the outstanding magnetic flux trapping ability of bulk superconductors in practical applications. We report a 4.8 T peak trapped magnetic field, B T, achieved at 30 K in a 36 mm diameter GdBa2Cu3O7-δ –Ag bulk superconductor using pulsed field magnetization (PFM). To realize this, we have developed a reliable two-step multi-pulse PFM process based on understanding and exploiting the avalanche-like flux jump phenomenon observed in these materials. The magnitude of the applied pulsed magnetic field (B a) necessary to trap 4.8 T was merely 5.29 T, corresponding to a remarkable magnetization efficiency (B T/B a) of 90%.

© 2016 American Chemical Society.Single grain, rare earth-barium-copper oxide [(RE)BCO] bulk superconductors, fabricated either individually or assembled in large or complicated geometries, have a significant potential for a variety of potential engineering applications. Unfortunately, (RE)BCO single grains have intrinsically very low growth rates, which limits the sample size that may be achieved in a practical, top seeded melt growth process. As a result, a melt process based on the use of two or more seeds (so-called multiseeding) to control the nucleation and subsequent growth of bulk (RE)BCO superconductors has been developed to fabricate larger samples and to reduce the time taken for the melt process. However, the formation of regions that contain non-superconducting phases at grain boundaries has emerged as an unavoidable consequence of this process. This leads to the multiseeded sample behaving as if it is composed of multiple, singly seeded regions. In this work we have examined the factors that lead to the accumulation of non-superconducting phases at grain boundaries in multiseeded (RE)BCO bulk samples. We have studied the microstructure and superconducting properties of a number of samples fabricated by the multiseeded process to explore how the severity of this problem can be reduced significantly, if not eliminated completely. We conclude that, by employing the techniques described, multiseeding is a practical approach to the processing of large high performance superconducting bulk samples for engineering applications.

Large, single-grain bulk high-temperature superconducting materials can trap high magnetic fields in comparison with conventional permanent magnets, making them ideal candidates to develop more compact and efficient devices, such as actuators, magnetic levitation systems, flywheel energy storage systems and electric machines. However, macrosegregation of Y-211 inclusions in melt-processed Y-Ba-Cu-O (YBCO) limits the macroscopic critical current density of such bulk superconductors, and hence, the potential trapped field. A new fabrication technique using graded precursor powders has recently been developed by our research group, which results in a more uniform distribution of Y-211 particles, in order to further improve the superconducting properties and trapped field capability of such materials. Large, single-grain bulk high-temperature superconducting materials can trap high magnetic fields in comparison with conventional permanent magnets, making them ideal candidates to develop more compact and efficient devices, such as actuators, magnetic levitation systems, flywheel energy storage systems and electric machines. However, macrosegregation of Y-211 inclusions in melt-processed Y-Ba-Cu-O (YBCO) limits the macroscopic critical current density of such bulk superconductors, and hence, the potential trapped field. A new fabrication technique using graded precursor powders has recently been developed by our research group, which results in a more uniform distribution of Y-211 particles, in order to further improve the superconducting properties and trapped field capability of such materials.

Bulk large-grain superconductors can be used as high-field permanent magnets. Although the properties of such individual trapped field magnets are well documented, much less is known concerning their behaviour when two are brought together. In this work, the interaction between two cylindrical bulk YBa2Cu3O7 (YBCO) superconductors is described. Two sets of experiments were carried out. The first set of experiments involved the simultaneous magnetization of two bulk superconductors placed a short distance apart. The applied magnetic field was aligned parallel to the c-axis of one bulk, while the other had its c-axis directed at different angles. For a centre-to-centre distance equal to twice the sample height, the presence of the second sample is found not to alter the current distribution inside the first. Consequently, the contribution of both samples simply sums, thus increasing the magnetic flux density between them. In the second set of experiments, the translational approach of the superconductors with parallel c-axes was investigated. The following configurations were considered: (i) face to face approach (with anti-parallel trapped field orientation) and (ii) sideways approach (with parallel trapped field orientation). An irreversible decrease of the trapped field was measured when the samples are separated again. Repeated approach cycles showed that the irreversible loss of trapped field is most significant for the first approach.

The superconducting properties, melting temperatures and crystal growth rates of single grain, RE–Ba–Cu–O [(RE)BCO] bulk superconductors (where RE = a rare earth element or yttrium) decrease with the RE-element sequence of Nd, Sm, Eu, Gd, Dy and Y. The mechanical properties of these technologically important materials, on the other hand, however, improve in the same sequence. Consequently, one promising approach for optimising the balance between mechanical and superconducting properties of bulk (RE)BCO superconductors, or for adjusting growth rate, is the use of combinations of different rare earth elements. In this study, we explore combinations of Gd and Y in the formation of (Gd–Y)–Ba–Cu–O single grains. We describe the optimisation of the growth process for this multi-RE element system and use optical and scanning electron microscopy to study the microstructure of both non-superconducting (Gd–Y)2BaCuO5 [(Y–Gd)-211] phase inclusions and the (Y–Gd)Ba2Cu3O7-δ [(Y–Gd)-123] phase matrix itself. We demonstrate that (Gd–Y)–Ba–Cu–O single grains can be fabricated reliably and that they exhibit reasonably good superconducting properties. We observe that there is an increase in RE-211 particle size in this mixed rare earth system, which, ultimately, limits sample performance, and conclude that this may be a general disadvantage of this approach to the synthesis of single grains for high field engineering applications.

Bulk (RE)BCO, where RE is a rare-earth element or yttrium, superconductors fabricated in the form of rings are potentially useful for a variety of solenoidal-type applications, such as small, high field nuclear magnetic resonance and electromagnetic undulators. It is anticipated that the practical exploitation of these technologically important materials will involve pulse field magnetization (PFM) and, consequently, it is important to understand the behavior of ring-shaped samples subjected to the PFM process. Macroscopic flux jumps were observed in PFM experiments on ring-shaped bulk samples when the peak applied field reaches a threshold magnitude, similar to behavior reported previously in cylindrical samples. Magnetic flux jumps inward when the thermal instability is triggered, however it subsequently flows outwards from the sample, resulting in a relatively low trapped field. This behavior is attributed to a variety of effects, including the inhomogeneity of the material, which may lead to the formation of localized hot spots during the PFM process. In order to further elucidate this phenomena, the properties of a structure consisting of a bulk superconducting ring with a cylindrical superconductor core were studied. We observe that, although a flux jump occurs consistently in the ring, a critical state is established at the boundary of the ring-shaped sample and the core. We provide a detailed account of these experimental observations and provide an explanation in terms of the current understanding of the PFM process.

Trapped fields of over 20 T are, in principle, achievable in bulk, single-grain high temperature cuprate superconductors. The principle barriers to realizing such performance are, firstly, the large tensile stresses that develop during the magnetization of such trapped-field magnets as a result of the Lorentz force, which lead to brittle fracture of these ceramic-like materials at high fields and, secondly, catastrophic thermal instabilities as a result of flux movement during magnetization. Moreover, for a batch of samples nominally fabricated identically, the statistical nature of the failure mechanism means the best performance (i.e. trapped fields of over 17 T) cannot be attained reliably. The magnetization process, particularly to higher fields, also often damages the samples such that they cannot repeatedly trap high fields following subsequent magnetization. In this study, we report the sequential trapping of magnetic fields of ~ 17 T, achieving 16.8 T at 26 K initially and 17.6 T at 22.5 K subsequently, in a stack of two Ag-doped GdBa2Cu3O7-{\delta} bulk superconductor composites of diameter 24 mm reinforced with (1) stainless-steel laminations, and (2) shrink-fit stainless steel rings. A trapped field of 17.6 T is, in fact, comparable with the highest trapped fields reported to date for bulk superconducting magnets of any mechanical and chemical composition, and this was achieved using the first composite stack to be fabricated by this technique., Comment: Accepted revised version for Superconductor Science and Technology

The widespread use of melt processed, single grain (RE)–Ba–Cu–O bulk superconductors [(RE)BCO], where RE = Y, Gd or Sm, is limited predominantly by the poor mechanical properties of these inherently brittle, ceramic-like materials. The high density of flaws, such as cracks and voids, within the single grain microstructure leads directly to a low fracture toughness. As a result, the Lorentz forces, generated when these materials carry current in the presence of a large magnetic field, create stresses sufficiently large to cause brittle failure. The addition of Ba–Cu–O (liquid phase) and Ag to the precursor composition prior to melt-growth has been demonstrated to be effective in improving the mechanical properties of these technologically important materials. In this work, we characterise the mechanical failure of single grain YBCO bulk superconductors in terms of a Weibull statistical distribution. In addition, differences in fracture mechanisms have been studied to provide a better understanding of how the provision of additional liquid phase and silver produces YBCO single grains with better resulting mechanical properties and how these can be improved further.

The levitation force between a single grain YBCO cylindrical bulk superconductor and a permanent magnet is investigated. The force measured both in zero field cooling and field cooling condition in the temperature range 20 K - 80 K is reported. The dependence of peak levitation force and power dissipation on the temperature is analyzed and the saturation of the peak force with increasing the critical current of the material is pointed out. A numerical analysis is also carried out for understanding the electrodynamics of the levitation mechanism. Good reproduction of the measured data is obtained and relevant observed phenomena, such as hysteresis of the levitation cycle at high temperature and saturation of the peak force at low temperature, are explained by means of the model. Characterization of the material in terms of critical current density in the field range 0 T - 0.5 T is also obtained by means of the numerical model by means of the fitting of the measured data.

© Published under licence by IOP Publishing Ltd. The large scale use of (RE)Ba2Cu3O7 bulk superconductors, where RE=Y, Gd, Sm, is, in part, limited by the relatively poor mechanical properties of these inherently brittle ceramic materials. It is reported that alloying of (RE)Ba2Cu3O7 with silver enables a significant improvement in the mechanical strength of bulk, single grain samples without any detrimental effect on their superconducting properties. However, due to the complexity and number of inter-related variables involved in the top seeded melt growth (TSMG) process, the growth of large single grains is difficult and the addition of silver makes it even more difficult to achieve successful growth reliably. The key processing variables in the TSMG process include the times and temperatures of the stages within the heating profile, which can be derived from the growth rate during the growth process. To date, the growth rate of the YBa2Cu3O7-Ag system has not been reported in detail and it is this lacuna that we have sought to address. In this work we measure the growth rate of the YBCO-Ag system using a method based on continuous cooling and isothermal holding (CCIH). We have determined the growth rate by measuring the side length of the crystallised region for a number of samples for specified isothermal hold temperatures and periods. This has enabled the growth rate to be modelled and from this an optimized heating profile for the successful growth of YBCO-Ag single grains to be derived.

In this paper single domain, bulk SmBCO samples have been fabricated successfully in air in a top-seeded melt growth (TSMG) process using a conventional chamber furnace, in addition to samples doped with ZrO 2 . To improve the reliability of seeding, Sm-123 + Sm-211 mixed-powder buffers were used to increase the success of the SmBCO single grain growth process. SmBCO single grains of diameter as large as 20 mm and 10 mm in thickness with and without ZrO 2 were fabricated successfully using Sm-123 + Sm 2 BaCuO 5 (Sm-211) mixed-powder buffer layers. The geometric configurations of the buffers were also optimized as part of this study to further increase the success of the single grain growth process. Superconducting properties of J C and T C of the specimens under the buffer layer have also been investigated.

The widespread use of RE-Ba-Cu-O [(RE)BCO] bulk superconductors, where RE=Y, Gd or Sm, in practical applications requires large single grains that exhibit uniform superconducting properties. Until recently, however, it was difficult to grow successfully YBCO-Ag bulk materials in the required single grain form, due primarily to the relative complexity of the top seeded melt growth process (TSMG) and the introduction of an alloying element (Ag) to the precursor composition. In most cases, alloying elements are used to improve the mechanical properties of the bulk superconductor whilst, at the same time, aim to cause minimal detrimental effect on the superconducting properties of the fully processed sample. In this work we investigate the effect of the addition of silver to YBCO on the superconducting properties of the bulk single grain, including trapped field, T c and J c , and on the sample microstructure.

Mammalian cells are involved in a range of biotechnological applications and more recently have been increasingly exploited in regenerative medicine. Critical to successful applications involving mammalian cells are their long-term storage and transport, for which cryopreservation in liquid nitrogen is the most frequently used strategy. However, cryopreservation suffers from high costs, difficulties in transport logistics and the use of undesirable additives (e.g. animal sera or DMSO). An alternative approach, proposed as low cost, low maintenance and process-compatible, is viable desiccation of mammalian cells. Several groups claim to have achieved this, but the extent of desiccation in the cell samples concerned is not always clear, in part because of difficulties in determining very low water content. Although several techniques exist that are frequently used to quantify the amount of water in samples (e.g. FTIR spectroscopy, thermogravimetric analysis (TGA), NMR spectroscopy), the complexity of sample preparation, as well as the costs and time constraints involved are disadvantageous. Here, we assess a novel, rapid and low cost technique, i.e. terahertz (THz) spectroscopy, for the quantification of water content within dehydrated mammalian cell samples.

We report the design and construction of a flux extraction device to measure the DC magnetic moment of large samples (i.e., several cm(3)) at cryogenic temperature. The signal is constructed by integrating the electromotive force generated by two coils wound in series-opposition that move around the sample. We show that an octupole expansion of the magnetic vector potential can be used conveniently to treat near-field effects for this geometrical configuration. The resulting expansion is tested for the case of a large, permanently magnetized, type-II superconducting sample. The dimensions of the sensing coils are determined in such a way that the measurement is influenced by the dipole magnetic moment of the sample and not by moments of higher order, within user-determined upper bounds. The device, which is able to measure magnetic moments in excess of 1 A m(2) (1000 emu), is validated by (i) a direct calibration experiment using a small coil driven by a known current and (ii) by comparison with the results of numerical calculations obtained previously using a flux measurement technique. The sensitivity of the device is demonstrated by the measurement of flux-creep relaxation of the magnetization in a large bulk superconductor sample at liquid nitrogen temperature (77 K).

A trapped magnetic field of greater than 3 T has been achieved in a single grain GdBa2Cu3O7-{\delta} (GdBaCuO) bulk superconductor of diameter 30 mm by employing pulsed field magnetisation (PFM). The magnet system is portable and operates at temperatures between 50 K and 60 K. Flux jump behaviour was observed consistently during magnetisation when the applied pulsed field, Ba, exceeded a critical value (e.g. 3.78 T at 60 K). A sharp dBa/dt is essential to this phenomenon. This flux jump behaviour enables the magnetic flux to penetrate fully to the centre of the bulk superconductor, resulting in full magnetization of the sample without requiring an applied field as large as that predicted by the Bean model. We show that this flux jump behaviour can occur over a wide range of fields and temperatures, and that it can be exploited in a practical quasi-permanent magnet system., Comment: 8 pages, 4 figures. Accepted for publication in APL

Reliable seeding of the superconducting (RE)Ba2Cu3O7−δ (RE-123) phase is a critical step in the melt growth of large, single grain, (RE)BaCuO ((RE)BCO) bulk superconductors. Recent improvements to the top seeded melt growth (TSMG) processing technique, which is an established method of fabricating bulk (RE)BCO superconductors, based on the use of a buffer layer between the seed and green body preform, has significantly improved the reliability of the single grain growth process. This technique has been used successfully for the primary TSMG and infiltration melt growth of all compositions within the ((RE)BCO–Ag) family of materials (where RE = Sm, Gd and Y), and in recycling processes. However, the mechanism behind the improved reliability of the melt process is not understood fully and its effect on the superconducting properties of the fully processed single grains is not clear. In this paper, we investigate the effect of the use of a buffer pellet between the seed and green body on the microstructure, critical current, critical temperature and trapped field of the bulk superconductor. We conclude that the introduction of the buffer pellet evolves the melt growth process towards that observed in the technologically challenging hot seeding technique, but has the potential to yield high quality single grain samples but by a commercially viable melt process.

Large, single-grain (RE)BCO (where RE = rare earth or Y) bulk superconductors with complicated geometries are required for a variety of potential applications, such as rotating machines, magnetic bearings and magnetic separation. As a consequence, the top multi-seeded melt growth process has been studied over many years in an attempt to deliver large, single grains for practical applications. Among these techniques, the so-called bridge-seeding produces the best alignment of two seeds during melt processing of multi-seed samples. In this paper, the trapped field performance and magnetic flux dynamics of two bridge-seeded, multi-seed samples magnetized by pulsed field magnetization are analyzed: one with a 45°–45° and another with a 0°–0° bridge seed. Based on an analysis of the flux penetration across the seeds and in-between the seeds of the 45°–45° multi-seed sample, an estimated J c distribution over the ab-plane is determined, which provides the basis for further analysis via numerical simulation. A three-dimensional finite-element model, developed to qualitatively reproduce and interpret the experimental results, was employed to investigate the influence of the length of the bridge seed for such multi-seed samples. The simulation results agree well with the observed experimental results, in that the multi-seed sample's particular inhomogeneous J c distribution acts to distort the trapped field profile from a traditional conical Bean's profile, which is determined by the length and direction of the bridge seed on the bulk surface.

Bulk, high temperature superconductors have significant potential for use as powerful permanent magnets in a variety of practical applications due to their ability to trap record magnetic fields. In this paper, soft ferromagnetic sections are combined with a bulk, large grain Y–Ba–Cu–O high temperature superconductor to form superconductor/ferromagnet hybrid structures. We study how the ferromagnetic sections influence the shape of the profile of the trapped magnetic induction at the surface of each structure and report the surface magnetic flux density measured by Hall probe mapping. These configurations have been modelled using a 2D axisymmetric finite element method based on the H -formulation and the results show excellent qualitative and quantitative agreement with the experimental measurements. The model has also been used to study the magnetic flux distribution and predict the behaviour for other constitutive laws and geometries. The results show that the ferromagnetic material acts as a magnetic shield, but the flux density and its gradient are enhanced on the face opposite to the ferromagnet. The thickness and saturation magnetization of the ferromagnetic material are important and a characteristic ferromagnet thickness d* is derived: below d*, saturation of the ferromagnet occurs, and above d*, a weak thickness-dependence is observed. The influence of the ferromagnet is observed even if its saturation magnetization is lower than the trapped flux density of the superconductor. Conversely, thin ferromagnetic discs can be driven to full saturation even though the outer magnetic field is much smaller than their saturation magnetization.