Search

Stainless steel and titanium-based alloys have been the gold standard when it comes to permanent implants and magnesium-based alloys have been the best option for bioresorbable alloys. Ti-6Al-4V, Ti-64, with its 110 GPa Young's Modulus is the most commonly employed alloy to manufacture biomedical implants used for treatment of fractures of skeleton. Recently, researchers have developed a new low-cost and toxic Vanadium-free alternative to this alloy, Ti-3Mo-0.5Fe at.%, namely TMF8. This alloy has a 25% lesser Young's Modulus compared to Ti-6Al-4V and also demonstrated acceptable mechanical properties while possessing better cell proliferation results. The lower Young's Modulus can aid in lowering stress shielding effects while its cytocompatibility could enhance healing. This work, therefore, tries to use finite element analyses to compare these two alloys (Ti-64 and TMF8) from a practical structural point of view to analyse the advantages and disadvantages of this new alloy and how a low-cost biocompatible alternative (TMF8) can actually prove to be a more viable option. The analyses confirm that TMF8 shows almost similar biomechanics performance to Ti-64 alloy (and in acceptable range) in bone plate fixation of mandibular angular fracture treatment., Competing Interests: Compliance with ethical standards. Conflict of interest: The authors declare no competing interests., (© 2024. The Author(s).)

On some occasions, such as new energy clinics, monitoring the trace hydrogen at the ppb level is necessary. The traditional resistive hydrogen sensors based on the Pd alloys are very difficult to realize such an extremely low detection limit. To achieve a detection limit at the ppb level and also ensure good stability, a MEMS hydrogen sensor was designed in a suspended Wheatstone bridge structure, with all four resistive arms defined on a sputtered Pd-Au alloy thin film. For the Wheatstone bridge sensor, absolute response ( R a ) and relative response ( R s ) are defined to describe the sensitivity of the sensor, and the effect of annealing temperature on baseline drift is investigated using the baseline zero drift parameter (DBZD). By testing the sensors across a hydrogen concentration range of 20 ppb to 3 v/v%, the optimal annealing temperature (250 °C) and operating temperature (60 °C) were identified. Under these conditions, the sensor exhibited a detection limit as low as 20 ppb with a power consumption of only 4.6 mW. At the same time, the response and recovery times of the sensor were 6 and 19 s, respectively, toward 3 v/v% hydrogen. After testing over a 100-day period, R a fluctuated only 0.0026%, indicating that the hydrogen sensor had good long-term stability for low-concentration detection. More results also showed that the sensor has good repeatability, selectivity, and humidity resistance. With the wide measurement range (20 ppb to 3 v/v%), the sensor has the potential to meet hydrogen detection requirements in multiple scenarios.

Orthopedic injuries, such as femur shaft fractures, often require surgical intervention to promote healing and functional recovery. Metal plate implants are widely used due to their mechanical strength and biocompatibility. Biodegradable metal plate implants, including those made from magnesium, zinc, and iron alloys, offer distinct advantages over non-biodegradable materials like stainless steel, titanium, and cobalt alloys. Biodegradable implants gradually replace native bone tissue, reducing the need for additional surgeries and improving patient recovery. However, non-biodegradable implants remain popular due to their stability, corrosion resistance, and biocompatibility. This study focuses on designing an implant plate for treating transverse femoral shaft fractures during the walking cycle. The primary objective is to conduct a comprehensive finite element analysis (FEA) of a fractured femur's stabilization using various biodegradable and non-biodegradable materials. The study assesses the efficacy of different implant materials, discusses implant design, and identifies the optimal materials for femoral stabilization. Results indicate that magnesium alloy is superior among biodegradable materials, while titanium alloy is preferred among non-biodegradable options. The findings suggest that magnesium alloy is the recommended material for bone implants due to its advantages over non-degradable alternatives., (© 2024 IOP Publishing Ltd. All rights, including for text and data mining, AI training, and similar technologies, are reserved.)

Introduction: Modular hip implants enables a more precise adaptation of the prosthesis to the patient's anatomy. However, they also carry the risk of increased revision rates due to micromotion at the taper junction. In order to minimize this risk, one potential solution is to establish an adhesive bond between the metal taper junctions. Load-stable bonding techniques, already successfully employed in dentistry for connecting materials such as metals and ceramics or different alloys, offer a promising approach. Nevertheless, the bond strength of tapered adhesive bonds in modular hip implants has not been investigated to date., Materials and Methods: Twenty-eight tapered junctions, consisting of a taper (female taper) and a trunnion (male taper) were turned using TiAl6V4 ELI (n = 16) and CoCr28Mo6 (n = 12). The process parameters cutting speed (vc = 50 m/min or 100 m/min) and feed (f = 0.1 mm, 0.05 mm or 0.2 mm) were varied for the trunnions. For each set of process parameters, one trunnion and one taper were additionally subjected to sandblasting. To investigate the effect of geometry, angular mismatch in the samples were measured. The taper pairs were bonded with a biocompatible adhesive, and push-out tests were subsequently performed., Results: The push-out forces generated from the taper connections where both tapers were sandblasted showed a mean push-out force of 5.70 kN. For the samples with only the trunnion sandblasted, the mean force was 0.58 kN, while for the samples with only taper sandblasted the mean push-out force was 1.32 kN. When neither of the tapers was sandblasted the mean push-out force was 0.91 kN. No significant effect of the process parameters on the push-out force was observed. Only the reduced valley depth Svk showed a slight correlation for the CoCr28Mo6 samples (R2 = 0.54). The taper pairs with taper mismatch (between trunnion and taper) greater than |0.1°| did not show lower push-out forces than the specimens with lower taper mismatch., Conclusions: Sandblasted and adhesive-bonded tapered connections represent a viable suitable alternative for modular hip implant connections. Slight differences in taper geometry do not result in reduced push-out forces and are compensated by the adhesive. In mechanically joined tapers these differences can lead to higher wear rates. Further investigation under realistic test conditions is necessary to assess long-term suitability., Competing Interests: The authors have declared that no competing interests exist., (Copyright: © 2024 Einfeldt et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

The implantation of digestive tract stents at various lesion sites can effectively improve digestive tract patency, opening up an excellent treatment method for diseases that are currently incurable or resistant to conventional surgery. Digestive tract stents have been extensively studied and widely used worldwide due to their unique advantages of simple implantation, low trauma, satisfactory effect, and low complication rate. Among the various types of stents, metallic stents have been developed to improve surgical efficacy due to their excellent mechanical properties and are constantly being improved. This review provides an overview of the design and development of conventional nonbiodegradable metallic digestive tract stents such as nitinol (NiTi alloy), stainless steel, and cobalt-based alloy stents. Furthermore, biodegradable metallic stents for the digestive tract, such as magnesium-based, iron-based, and zinc-based stents, are described. This paper also evaluates the advantages and disadvantages of existing metallic digestive stents as well as future research directions and challenges in the development of metallic digestive tract stents.

Stress shielding in dental and orthopedic implants is a long-standing hurdle, and trabecular porous architecture to improve bone ingrowth is deemed to be a potential solution. Fabricating Ti 6 Al 4 V components with dense-porous bilayer structures is complicated with limited lab-scale and commercial success. Here, a green dough-forming technique with metal powders is successfully explored to develop heterogeneous structures with a monolith-like dense-porous interface. The porous region achieved 70% porosity with a 25 MPa compressive strength comparable to human cancellous bone. Due to its simplicity and versatility, this process is a promising solution for developing and mass-manufacturing customized designs for bone-related implants with improved bone ingrowth and osseointegration.

TiO 2 nanotubes (NTs) obtained via electrochemical anodization (EA) on conventionally machined titanium surfaces are reported to be promising for achieving mucointegration in dental implant therapy. Dental abutments, manufactured by selective laser melting (SLM), combined with thermal post-treatment, present a promising alternative to conventionally machined titanium. Based on an original protocol, this study aims to investigate how the characteristic microstructure of the α + β phases in post-heated SLM Ti6Al4V can influence the growth of NTs and the resulting physical and chemical surface properties. Ti6Al4V-SLM discs were fabricated, heat post-treated and mechanically polished. The samples were then subjected to EA under different voltage conditions (10, 20 and 30 V). The specimens' surfaces were characterized at the same location, before NTs formation by electron backscatter diffraction (EBSD), and after by scanning electron microscopy (SEM). Then, roughness and wettability were studied to determine how EA affects surface properties compared to conventionally machined and polished titanium surfaces without NTs (reference). Surface reactivity was evaluated through chemical analysis and collagen binding capacities. The self-organized TiO 2 layer was developed on the α phase only and the β phase was preferentially dissolved. The characteristic dimensions of the nanotubes (diameter, length and wall thickness), measured by SEM image analysis, increased proportionally with the rise in voltage but were not affected by the crystallographic orientation of the underlying α grain. Micro-roughness was the same for nanotubular and reference surfaces. Wettability was improved, as was surface reactivity towards collagen, which may contribute to improved bioactivity of titanium surfaces in dentistry.

Background : Magnesium alloys degrade rapidly in salt solutions, which limits their use without passivating treatments. AZ31 alloy is particularly promising for implant applications owing to its biodegradability and mechanical properties, necessitating effective corrosion-resistant coatings. Aim : In this study, a self-passivating reactive coating was designed and evaluated for AZ31 magnesium alloy plates using β-tricalcium phosphate (TCP) to enhance corrosion resistance and biocompatibility. Methods : Solutions of TCP, trisodium citrate, magnesium nitrate, hydroxyethyl cellulose (HEC), and sodium chloride were used to dip-coat AZ31 plates. The coated samples were immersed in 3.5 wt% NaCl solution. Phase evolution was analysed using gravimetry, X-ray diffraction (XRD), energy-dispersive X-ray (EDX) spectroscopy, and scanning electron microscopy (SEM). The biological response of the coated samples was evaluated through MTT and resazurin assays. Results : The coating formed a stable TCP/HEC layer that gradually dissolved over two weeks, converting the surface to magnesium hydroxide, magnesium oxychloride, and magnesium phosphate phases. The formation of brucite, responsible for passivation in the long term, was observed. The coating effectively prevented excessive magnesium oxychloride formation and stabilised magnesium hydroxide after one week. Biological characterization indicated that the coating on AZ31 is safe on the Saos-2 and L929 cell lines. Conclusion : The TCP-based coating enhances the corrosion resistance of AZ31 alloy in salt solutions, promoting passivating phases and limiting corrosive products, thereby ameliorating biocompatibility issues. This coating demonstrates substantial potential for extending the longevity and functionality of magnesium alloy implants.

We report the preparation of a small library of copper-based metallenes, such as copperene, brassene, bronzene, cupronickelene and AlCuZn trimetallene, via a cryo-pretreatment assisted liquid phase exfoliation method. To the best of our knowledge, these nanosheets may represent a new category of metallenes. Benefiting from mixed-valence copper-induced oxidative stress and cleavage effects of layered structures, the obtained metallenes could efficiently eliminate drug-resistant bacteria even at a concentration as low as 1 μg mL -1 . Due to the alloy engineering-induced change in the release rate of metal ions, the CuZn metallene exhibited a much better antibacterial ability than the other metallenes and three clinical antibiotics. We believe this work not only expands the category of emerging 2D metallenes, but also proposes a strategy combining 2D and alloy engineering to improve the antibacterial properties of copper-based materials.

A layer-by-layer chemical bonding strategy was developed for fast in situ growth of bifunctional mesoporous covalent organic framework submicrospheres (COF SMSs) on the nickel-chromium alloy (Ni-Cr) fiber substrate via the ultrasound-assisted Schiff-base reaction for the first time. COF SMSs showed well-defined morphology, extraordinary high surface area (1211 m 2 ·g -1 ) and narrow mesopore (2.50 nm) as well as excellent stability. Furthermore, the resulting Ni-Cr fiber presented outstanding adsorption capability and improved selectivity for bisphenols (BPs). Consequently, an attractive SPME-HPLC-UV approach with the Ni-Cr@Ni-Cr LDHs NSs@COF SMSs fiber was proposed for rapid preconcentration and sensitive determination of BPs. By optimizing adsorption parameters, the SPME-HPLC-UV method presented good linearity for five BPs in the ranges of 0.02-200 ng·mL -1 with coefficients of determination (R 2 ) higher than 0.999. Limits of detection and limits of quantitation were obtained from 0.003 ng·mL -1 to 0.006 ng·mL -1 and from 0.010 to 0.019 ng·mL -1 , respectively. Moreover, the intra-day and inter-day precision expressed as relative standard deviations (RSDs) was 1.57-3.52 % and 2.65-4.38 % for the proposed method with a single fiber, respectively. RSDs of the proposed method with different duplicate fibers were 3.25-6.72 %. The proposed SPME-HPLC-UV method was available for efficient preconcentration and sensitive detection of five BPs from real water and milk samples. The relative recoveries at three spiking levels of BPs were achieved in the range of 80.00-118.8 % with RSDs below 7.81 %. In addition, the prepared fiber still exhibited satisfactory adsorption performance after 120 adsorption-desorption cycles., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Healthcare-associated infections (HCAIs) pose a significant global health challenge, exacerbated by the rising threat of antimicrobial resistance (AMR). This study introduces a high-throughput platform designed to identify sustainable antibacterial surfaces, exemplified by a copper-silver-zirconium (CuAgZr) alloy library. Utilizing combinatorial synthesis and advanced characterization techniques, material libraries (MatLibs) are generated and evaluated to rapidly screen diverse alloy compositions. The results demonstrate the ability to reproducibly create alloys with significant antimicrobial properties and high hardness, making them suitable for biomedical applications. The study highlights the critical role of compositional precision in developing materials that balance mechanical strength with antibacterial efficacy. Additionally, this approach ensures significant cost-effectiveness, facilitating the identification of economically viable alloy compositions. This research underscores the potential of high-throughput materials science to expedite the discovery of sustainable solutions for reducing HCAIs and addressing AMR, signaling a leap forward in sustainable healthcare material development.

The growth of spherical crystals in binary alloy melts with thermal diffusion effects under oscillatory flow is investigated analytically. Using the multiple scale method, we derive approximate analytical solutions for both the crystal interface growth rate and the solute concentration. Our results demonstrate that the Soret effect significantly influences both the solute concentration near the crystal interface and the crystal growth rate. Specifically, with a positive Soret coefficient, the growth rate of spherical crystals in a binary dilute alloy melt decreases as the coefficient increases, while the solute concentration near the interface increases. In contrast, with a negative Soret coefficient, the growth rate of the spherical crystals increases as the coefficient decreases, and the solute concentration near the interface decreases. Additionally, the presence of oscillatory flow markedly promotes the grain refinement induced by the Soret effect., Competing Interests: The authors have declared that no competing interests exist., (Copyright: © 2024 Liu et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

An integrated strategy by combining cocrystallization with nanotechnology is developed to optimize in vitro/vivo performances of marine antitumor drug cytarabine (ARA) and further obtain innovative insights into the exploitation of cocrystal alloy nanoformulation. Therein, the optimization of properties and synergistic effects of ARA mainly depends on assembling with uracil (U) and antitumor drug 5-fluorouracil (FU) into the same crystal by cocrystallization technology, while the long-term efficacy is primarily maintained by playing the superiority of nanotechnology. Along this line, the first cocrystal alloy of ARA, viz. , ARA-FU-U (0.6:0.4), is successfully obtained and then transformed into a nanocrystal. Single-crystal X-ray diffraction analysis demonstrates that this cocrystal alloy consists of two isomorphic cocrystals of ARA, namely, ARA-FU and ARA-U, in 0.6:0.4 ratio. An R 2 2 (8) hydrogen-bonding cyclic system formed by a cytosine fragment of ARA with U or FU can protect and stabilize the amine group on ARA, laying the foundation for regulating its properties. The in vitro / in vivo properties of the cocrystal alloy and its nanocrystals are investigated by theoretical and experimental means. It reveals that both the alloy and nanocrystal can improve physicochemical properties and promote drug absorption, thus bringing to optimized pharmacokinetic behaviors. The nanocrystal produces superior effects than the alloy that helps to extend therapeutic time and action. Particularly, relative to the corresponding binary cocrystal, the synergistic antitumor activity of ARA and FU in the cocrystal alloy is heightened obviously. It may be that U contributes to reducing the degradation of FU, specifically increasing its concentration in tumors to enhance the synergistic effects of FU and ARA. These findings provide new thoughts for the application of cocrystal alloys in the marine drug field and break fresh ground for cocrystal alloy formulations to optimize drug properties.

The efficiency of drug delivery from coatings of metallic implants is one of the key factors. The influence of chemical and thermal treatments of nitinol wire on the corrosion properties, deposition of hydroxyapatite(HA)/poly ε-caprolactone-polyethylene glycol (PEG- b -PCL), and the amount of ibuprofen released from that bilayer were studied. The hydroxyapatite layer was electrodeposited by pulse current, while the PEG- b -PCL layer was by drop-coating. It was shown that nitinol wire, chemically treated and thermally heated at 470 °C under optimized conditions, is the most optimal substrate for the deposition of uniform and compact hybrid HA/(PEG- b -PCL) bilayer. Ibuprofen incorporated into this hybrid bilayer exhibits the maximum release into phosphate-buffered saline (PBS) solution. About 80% of ibuprofen is released within 5 h.

Nowadays, exoskeletons have a place in many fields, such as industrial production, medical rehabilitation, and military. However, there are still many shortcomings in the existing exoskeleton, such as heavyweight and complex structures for active exoskeleton. The driving ability of passive exoskeletons is limited. To reduce the energy consumption of wearers, based on the characteristics of the semi-active ankle exoskeleton, this paper proposes to use NiTiCu-based shape memory alloys (SMA) as the energy storage source to improve the power density. Compared to NiTi-based SMA, the phase transformation process of NiTiCu-based SMA is more rapid, which can solve the response delay problem to a certain extent. The ankle exoskeleton uses SMA deformation to compress the bias spring. When the human ankle joint needs auxiliary torque, the SMA releases the energy stored by the bias spring and transfers the energy to the ankle exoskeleton to achieve the effect of assisting the human ankle joint. During the assistance process, a control system based on the SMA mathematical model is constructed. The above-mentioned ideas provide a new approach for further expanding power density and can be widely applied in the field of robotics. During characterization, this semi-active ankle exoskeleton can effectively complete the movement state of upstairs and walking, achieve an effective power of 180 N, and store maximum energy up to 5 J for the human ankle., (© 2024 Author(s). Published under an exclusive license by AIP Publishing.)

Nano Al 3 Ti-TiB 2 -AlN-TiN/Al inoculant ribbons containing a large number of evenly distributed nanoparticles, such as Al 3 Ti (sized about 300 nm), TiB 2 (sized about 100 nm), AlN (sized about 150 nm), and TiN (sized about 200 nm), were prepared by vacuum rapid quenching furnace to refine AlZnMgCu alloys. The nano Al 3 Ti-TiB 2 -AlN-TiN/Al inoculant ribbons showed an excellent inoculant effect, which modified the dendrite crystals to equiaxed crystals and refined the grains from 122 ± 4 µm to 36 ± 5 µm by the addition of 0.3 wt% nano Al 3 Ti-TiB 2 -AlN-TiN/Al inoculant ribbons. In addition to nano Al 3 Ti and TiB 2 particles, nano AlN and TiN particles also have a certain orientation relationship with α-Al, which suggests that these particles possess nucleation potency to α-Al. After inoculation with 0.3% nano Al 3 Ti-TiB 2 -AlN-TiN/Al inoculant ribbons, the ultimate tensile strength, yield strength, and average microhardness of the AlZnMgCu alloys increased from 246 MPa, 79 MPa, and 112 HV to 319 MPa, 100 MPa, and 136 HV, or by 29.7%, 26.6% and 21.4%, respectively., (© 2024 The New York Academy of Sciences.)

Iron-selenium (Fe-Se) alloys have potential as attractive biodegradable bone-implant materials, given the antitumor properties of Se in cancer prevention and therapy. However, the fabrication of Fe-Se alloys is challenging due to the volatility of elemental Se and the significantly different melting points of Se and Fe. In this study, we successfully fabricated Fe-xSe (x = 0.2, 0.4, 0.6, 0.8, and 1 wt.%) alloys using suction casting, with FeSe compounds as the Se source. The microstructures, tensile properties, corrosion behavior, biocompatibility, antibacterial ability, and antitumor properties of the Fe-Se alloys were evaluated. The microstructures of the Fe-Se alloys were composed of α-Fe and FeSe phases. Among the Fe-Se alloys, Fe-0.6Se showed the best combination of tensile properties, with a yield strength of 1096.5 ± 7.2 MPa, an ultimate tensile strength of 1271.6 ± 6.3 MPa, and a fracture strain of 15.6 ± 3.3 %, and a degradation rate of 56.9 ± 0.4 μm/year. Moreover, the Fe-0.6Se alloy showed superb antibacterial ability against S. aureus, antitumor activity against 143B osteosarcoma cells, and osteogenicity and biocompatibility toward pre-osteoblast MC3T3-E1 cells. In summary, adding 0.2-1.0 wt.% Se to Fe does not affect the growth of healthy cells but effectively inhibits the growth and reproduction of tumor cells, and the Fe-0.6Se alloy is promising for orthopedic applications owing to its unique combination of mechanical and biofunctional properties. STATEMENT OF SIGNIFICANCE: This work reports on Fe-xSe (x = 0.2, 0.4, 0.6, 0.8, and 1 wt.%) alloys fabricated using suction casting. The microstructures of the Fe-Se alloys were composed of α-Fe and FeSe phases. Among the Fe-Se alloys, the Fe-0.6Se showed the best combination of tensile properties, with a yield strength of 1058.6 ± 3.9 MPa, an ultimate tensile strength of 1134.1 ± 2.9 MPa, and a fracture strain of 16.8 ± 1.5 %, and a degradation rate of 56.9 ± 0.4 μm/year. Moreover, the Fe-0.6Se alloy showed superb antibacterial ability against S. aureus, antitumor activity against 143B osteosarcoma cells, and significant osteogenic ability and biocompatibility toward pre-osteoblast MC3T3-E1 cells. In summary, the Fe-0.6Se alloy is promising for orthopedic applications owing to its unique combination of mechanical and biofunctional properties., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. The author is an Editorial Board Member/Editor-in-Chief/Associate Editor/Guest Editor for [Journal name] and was not involved in the editorial review or the decision to publish this article., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Modular hip implants are a clinically successful and widely used treatment for patients with arthritis. Despite ongoing retrieval studies the understanding of the fundamental physico-chemical mechanisms of friction and wear within the head-taper interface is still limited. Here, we Raman-spectroscopically analyze structural features of the biotribological material which is formed within the taper joint between Ti6Al4V and low-carbon cobalt alloy or high-nitrogen steel surfaces in in vitro gross-slip fretting corrosion tests with bovine calf serum. As a function of the fretting duration, we investigate short and long aliphatic chains and their adsorption behavior on the cobalt- and steel-type surfaces. Using the intensity and frequency shifts of the amide I and III Raman bands, we furthermore identify progressive protein folding and unfolding including the secondary structures of α-helix, β-sheet, and random-coil configuration as well as the formation of proteinaceous clusters depending on the hydrophilicity of the metallic surfaces. We additionally find a mixture of chromates and iron oxides with tryptophan and tyrosine at the worn cobalt alloy and high-nitrogen steel surfaces, respectively. Also, for long fretting duration, sp 2 hybridized amorphous carbon is formed due to fretting-induced cleavage of proteins. STATEMENT OF SIGNIFICANCE: Despite efforts enhancing the biomedical tribology of hip implants, the impact of the organic environment on friction and wear at the femoral head-stem taper interface is limitedly understood. Using Raman spectroscopy we resolve structural changes within the biotribological material agglomerated at biomedical-grade metal alloys due to metal-organic interactions during in vitro fretting corrosion tests. Adsorption of short and long aliphatic chains, progressive protein (un)folding and proteinaceous cluster formation depend to a distinguishable extent on the fretting duration and type of alloy. Chromates and iron oxides are mixed with tryptophan and tyrosine, and amorphous carbon is formed resulting from a fretting-induced cleavage of serum proteins. Such information spectroscopically gleaned from biotribological material are vital to improve the design and performance of taper junctions., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Copper-containing intrauterine devices (Cu-IUD) are adopted by worldwide women for contraception with the advantages of long-term effectiveness, reversibility and affordability. However, adverse effects occur in the initial implantation stage of Cu-IUD in uterine because of the burst release of Cu 2+ . To minimize the burst release, in this study, we designed a series of Cu-Fe alloys with 0.5 wt%, 1 wt% and 5 wt% Fe and also further produced ultrafine grained (UFG) structure for these alloys via equal-channel angular pressing. The microstructures and properties of the coarse grained (CG) Cu, CG Cu-Fe alloys and UFG Cu-Fe alloys were systematically investigated, including grain structure and phase compositions, metallic ions release behavior, electrochemical corrosion performance, and in vitro cytotoxicity. With careful comparison and selection, we chose the CG Cu-5Fe and UFG Cu-5Fe for in vivo tests using rat model, including tissue biocompatibility, in vivo corrosion behavior, and contraceptive effectiveness. Moreover, the corrosion mechanism of the Cu-5Fe alloy and its improved biocompatibility was discussed. Both CG and UFG Cu-5Fe alloys exhibited dramatic suppression of Cu 2+ release in simulated uterine fluid for the long-term immersion process. The in vivo tissue compatibility was significantly improved with both CG and UFG Cu-5Fe alloys implanted in the rats' uterine while the high contraceptive efficacy was well maintained. Due to the superior biocompatibility, the CG and UFG Cu-5Fe alloys can be the promising candidate material for Cu-IUD. STATEMENT OF SIGNIFICANCE: A highly biocompatible Cu-Fe alloy was designed and fabricated for Cu-containing intrauterine devices (Cu-IUD). With 5 wt% Fe, the burst release of Cu 2+ is inhibited due to the formed galvanic cell of Cu and Fe, resulting in earlier release of Fe 3+ . As Fe is the most abundant essential trace element of human body, it can mitigate the toxic effects of Cu 2+ , thus significantly improving both in vitro cell compatibility and in vivo tissue compatibility. More importantly, the Cu-5Fe alloy exhibits 100 % contraceptive efficiency as the CG Cu, but with greatly reduced adverse effects to the uterus tissues. An advanced Cu-IUD can be developed using Cu-Fe alloys., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier Ltd.. All rights reserved.)

Although significant progress in developing biodegradable magnesium alloy materials in cardiovascular stents has been achieved recently, they still face challenges such as rapid in vivo corrosion degradation, inferior blood compatibility, and limited re-endothelialization after the implantation. Hydrogel coating that can catalyze the liberation of gas signal molecules offers a good solution to alleviate the corrosion rate and enhance the biocompatibility of magnesium and its alloys. In this study, based on alkaline heat treatment and construction of polydopamine coating on the surface of magnesium alloy, sodium alginate/carboxymethyl chitosan (SA/CMCS) gel was simultaneously covalently grafted onto the surface to build a natural polymer hydrogel coating, and selenocystamine (SeCA) and CO release molecules (CORM-401) were respectively immobilized on the surface of the hydrogel coating to ameliorate the anticoagulant performance and accelerate endothelial cells (ECs) growth by catalyzing the release of endogenous gas signal molecules (NO or CO). The findings verified that the as-prepared hydrogel coating can catalyze the liberation of CO or NO and significantly improve the corrosion resistance of magnesium alloy. At the same time, owing to the excellent hydrophilicity of the hydrogel coating, the good anticoagulant property of sodium alginate, and the ability of CMCS to promote the ECs growth, the modified magnesium alloy could significantly improve the albumin adsorption while preventing the adsorption of fibrinogen, hence significantly augmenting the anticoagulant properties and promoting the ECs growth. Under the catalytic release of NO or CO, the released gas molecules further enhanced hemocompatibility and promoted endothelial cell (EC) growth and the expression of vascular endothelial growth factor (VEGF) and NO of ECs. Therefore, the bioactive coatings that can catalyze the release of NO or CO have potential applications in constructing surface bioactive coatings for magnesium alloy materials used for intravascular stents., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

In this experimental study, the initial phase involved preparing composite structures with various mix ratios using the Ti-6Al-4V alloy, widely used in clinical applications, in conjunction with ZrO 2 and hydroxyapatite (HA) synthesized via the precipitation method, employing powder metallurgy techniques. Subsequently, the microstructures of the resultant hybrid composite materials were imaged, and x-ray diffraction (XRD) phase analyses were conducted. In the final phase of the experimental work, tests were performed to determine the biocompatibility properties of the hybrid composites. For this purpose, cytotoxicity and genotoxicity assays were carried out. The tests and examinations revealed that structures compatible both morphologically and elementally were obtained with no phase transformations that could disrupt the structure. The incorporation of ZrO 2 into the Ti-6Al-4V alloy was observed to enhance cell viability values. The value of 98.25 ± 0.42 obtained by adding 20% ZrO 2 gave the highest cell viability result. The addition of HA into the hybrid structures further increased the cell viability values by approximately 10%. All viability values for both HA-added and HA-free groups were obtained above the 70% viability level defined in the standard. According to the genotoxicity test results, the highest cytokinesis-block proliferation index values were obtained as 1.666 and 0.620 in structures containing 20% ZrO 2 and 10% ZrO 2  + 10% HA, respectively. Remarkably, all fabricated composite and hybrid composite materials surpassed established biocompatibility standards and exhibited nontoxic and nongenotoxic properties. This comprehensive study contributes vital insights for future biomechanical and other in vitro and in vivo experiments, as it meticulously addresses fundamental characterization parameters crucial for medical device development. RESEARCH HIGHLIGHTS: Support of optimum doping rates ions on hybrid composites and concentrations. Development of uniform surface appearance and distributions/orientations of microcrystals on ceramic compounds Improvement of cell viability and desired increase in biocompatibility with the doping of HA., (© 2024 Wiley Periodicals LLC.)

A lot of attention has been drawn to photo-Fenton-like catalysis among advanced oxidation processes for environmental remediation applications. Herein, we have successfully fabricated iron-nickel bimetallic magnetic nano-alloy (INBMNA) as an efficient heterogeneous photo-Fenton-like catalyst using the chemical reduction method and characterized by several analytical techniques. The characterization results show that the catalyst has a spherical shape with a mesoporous nature and contains a large specific surface area. The impact of various parameters was investigated and optimized to check the catalytic performance of INBMNAs and the found results showed that excellent photo-Fenton-like activity persisted under 6.0 pH conditions for the degradation of hazardous pollutant (phenol) under solar light exposure and microwave radiation power, respectively. Additionally, the exposed INBMNA/H 2 O 2 system provided continuous redox cycles of Fe 3+ /Fe 2+ and Ni 2+ /Ni 0 pair in the Fenton-active species for stable operation. The photo-Fenton-like activity was also performed to check the effect of different inorganic anions which significantly hinder phenol reduction. Besides, the steady performance of the catalyst to remove phenol was performed in tap water and river water. Free radical trapping experiments were tested to know the role of important radicals in the photo-Fenton process. Moreover, the mechanism and possible degradation pathways of phenol were checked. By cyclic degradation experiments, the performance of the catalyst is stable and almost unchanged and can be reused several times. This study provides a promising INBMNA/H 2 O 2 system, which encourages its widespread use in environmental remediation applications., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests:, (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Magnesium is the most promising absorbable metallic implant material for bone regeneration and alloy WE43 is already FDA approved for cardiovascular applications. This study investigates the cyto- and biocompatibility of novel additively manufactured (AM) porous WE43 scaffolds as well as their osteogenic potential and degradation characteristics in an orthotopic canine bone defect model. The cytocompatibility was demonstrated using modified ISO 10993-conform extract-based indirect and direct assays, respectively. Additionally, degradation rates of WE43 scaffolds were quantified in vitro prior to absorption tests in vivo. Complete blood cell counts, blood biomarker analyses, blood trace element analyses as well as multi-organ histopathology demonstrated excellent biocompatibility of porous y WE43 scaffolds for bone defect repair. Micro-CT analyses further showed a relatively higher absorption rate during the initial four weeks upon implantation (i.e., 36 % ± 19 %) than between four and 12 weeks (41 % ± 14 %), respectively. Of note, the porous WE43 implants were surrounded by newly formed bony tissue as early as four weeks after implantation when unmineralized trabecular ingrowth was detected. After 12 weeks, a substantial amount of mineralized bone was detected inside and around the gradually disappearing implants. This first study on AM porous WE43 implants in canine bone defects demonstrates the potential of this alloy for in vivo applications in humans. Our data further underscore the need to control initial bulk absorption kinetics through surface modifications., Competing Interests: Declaration of competing interest The authors declare that the research was conducted without any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2024. Published by Elsevier B.V.)

Regarding its structural and mechanical adaptability to bone defects, 3D printed (3DP) Ti6Al4V scaffolds are widely used in orthopedics now, purposed to restore the function and mechanical stability of impaired bone. In scaffold fabrication, surface modification is acknowledged as a reliable strategy to enhance the interface interaction between 3DP Ti6Al4V scaffold and bone. Despite its advantage in bone-Ti6Al4V bonding improvement, surface modification lacks the ability to induce bone in-growth efficiently as expected. As an attempt to overcome this challenge, in the current work the inner voids of 3DP Ti6Al4V scaffold were occupied by a gelatin/chitosan porous matrix, purposed to act as a platform for guiding bone ingrowth. Firstly, the gelatin/chitosan matrix was prepared via freeze-drying using genipin as a crosslinker, resulting in a trabecular bone-like interconnected porous network characterized with a gelatin/chitosan ratio dependent swelling capability, degradation and model anti-bacterial drug release behavior. Besides of that, gelatin in the matrix was witnessed to accelerate biomineralization in simulated body fluid. Secondly, a formulated gelatin/chitosan matrix was embedded into 3DP Ti6Al4V scaffold to generate a composite scaffold capable of inducing bone in-growth. The followed studies showed gelatin/chitosan matrix can endow the scaffold with good biological and sustained drug release properties, along with minimal change to the compressive strength of the scaffold. The in vivo experiment results revealed that after 4 weeks of implantation, more new bone formation was witnessed in the inner structure of the composite scaffold than the 3DP Ti6Al4V scaffold, with the average bone volume fraction (BV/TV) value increased from 24.09 % to 46.08 %, the average trabecular bone thickness (Tb. Th) value increased from 0.118 mm to 0.278 mm. Therefore, it was confirmed an inner matrix in 3DP Ti6Al4V scaffold played an essential role in guiding bone in-growth., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

The development of cost-effective and highly efficient electrocatalysts is critical to help electrochemical non-enzymatic sensors achieve high performance. Here, a new class of catalyst, Ru single atoms confined on Cu nanotubes as a single-atom alloy (Ru 1 Cu NTs), with a unique electronic structure and property, was developed to construct a novel electrochemical non-enzymatic glucose sensor for the first time. The Ru 1 Cu NTs with a diameter of about 24.0 nm showed a much lower oxidation potential (0.38 V) and 9.0-fold higher response (66.5 μA) current than Cu nanowires (Cu NWs, oxidation potential 0.47 V and current 7.4 μA) for glucose electrocatalysis. Moreover, as an electrochemical non-enzymatic glucose sensor, Ru 1 Cu NTs not only exhibited twofold higher sensitivity (54.9 μA mM -1  cm -2 ) and wider linear range (0.5-8 mM) than Cu NWs, but also showed a low detection limit (5.0 μM), excellent selectivity, and great stability. According to theoretical calculation results, the outstanding catalytic and sensing performance of Ru 1 Cu NTs could be ascribed to the upshift of the d-band center that helped promote glucose adsorption. This work presents a new avenue for developing highly active catalysts for electrochemical non-enzymatic sensors., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH, DE part of Springer Nature.)

This study was designed to investigate the application value of shape memory alloy embracing fixator in the treatment of proximal clavicle fracture. From April 2018 to October 2020, the fracture data of patients with proximal clavicle fractures treated with shape memory alloy embracing fixator were retrospectively analyzed, including 12 males and 8 females. The age of patients ranged from 34 to 66 years (mean, 43.4 years). According to Craig's classification, the patients were divided into the following groups: type C II (eight cases), type C III (five cases), type C Ⅴ (seven cases), all of which were closed fractures without nerve or vascular injury. The fracture healing time and postoperative complications were observed, and the shoulder joint function was evaluated by Constant score. All patients were followed up for 13-19 months (average 15.6 months). The clavicle radiographs showed that all the 20 patients had bone union, and the fracture union time was 6-10 months (average 7.2 months). There were no complications such as internal fixation fracture and displacement. According to the Constant criterion, 13 cases were excellent and 5 cases were fair and 1 case was good. The treatment of proximal clavicle fracture with shape memory alloy embracing fixator is an effective treatment method with simple operation with satisfactory fixation effect and low complication rate, which is worthy of being widely used in clinical practice.

In this study, we have developed a novel, hypersensitive, and ultraselective electrochemical sensor containing thermally annealed gold-silver alloy nanoporous matrices (TA-Au-Ag-ANpM) integrated with f-MWCNTs-CPE and poly(l-serine) nanocomposites for the simultaneous detection of sulfathiazole (SFT) and sulfamethoxazole (SFM) residues in honey, beef, and egg samples. TA-Au-Ag-ANpM/f-MWCNTs-CPE/poly(l-serine) was characterized using an extensive array of analytical (UV-Vis, FT-IR, XRD, SEM, and EDX), and electrochemical (EIS, CV and SWV) techniques. It exhibited outstanding performance over a wide linear range, from 4.0 pM to 490 μM for SFT and 4.0 pM to 520 μM for SFM, with picomolar detection and quantification limits (0.53 pM and 1.75 pM for SFT, 0.41 pM and 1.35 pM for SFM, respectively). The sensor demonstrated exceptional repeatability, reproducibility, and anti-interference capability, with percentage recovery of 95.6-102.4% in food samples and RSD below 5%. Therefore, the developed sensor is an ideal tool to address the current antibiotic residue crisis in food sources., Competing Interests: Declaration of competing interest We want to affirm that there are no recognized conflicts of interest associated with this publication, and this study has not received dedicated funding from any public, commercial, or non-profit sector funding entity. The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023. Published by Elsevier Ltd.)

Uniform PtCoRuRhFe high-entropy alloy nanoflowers (HEANFs) were fabricated by a simple wet-chemical co-reduction method in oleylamine for quantitative colorimetric determination of captopril (CAP) based on multi-site synergistic signal amplification. Specifically, the peroxidase mimetic activity of the PtCoRuRhFe HEANFs was examined through catalysis of 3,3',5,5'-tetramethylbenzidine (TMB) oxidation, whose catalytic mechanism was investigated by electron paramagnetic resonance (EPR) spectroscopy. The role of the ·O 2 - was figured out during the catalytic procedure. Further, the oxidation of TMB (oxTMB) can be effectively reduced by CAP, accompanied by quickly transforming the solution color from blue to colorless. More importantly, the absorbance at 652 nm is linearly related to the CAP concentration in a range 5.0-50.0 mM with a low detection limit of 2.82 mM. The method has been applied to the determination of CAP in human urine samples. It offers a simple and high-efficiency method for facile and visual detection of CAP in hospitals., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Austria, part of Springer Nature.)

The general trend of increasing life expectancy will consistently drive the demand for orthopedic prostheses. In addition to the elderly, the younger population is also in urgent need of orthopedic devices, as bone fractures are a relatively common injury type; it is important to treat the patient quickly, painlessly, and eliminate further health complications. In the field of traumatology and orthopedics, metals and their alloys are currently the most commonly used materials. In this context, numerous scientists are engaged in the search for new implant materials and coatings. Among the various coating techniques, plasma electrolytic oxidation (PEO) (or micro-arc oxidation-MAO) occupy a distinct position. This method offers a cost-effective and environmentally friendly approach to modification of metal surfaces. PEO can effectively form porous, corrosion-resistant, and bioactive coatings on light alloys. The porous oxide surface structure welcomes organic molecules that can significantly enhance the corrosion resistance of the implant and improve the biological response of the body. The review considers the most crucial aspects of new combined PEO-organic coatings on metal implants, in terms of their potential for implantation, corrosion resistance, and biological activity in vitro and in vivo.

Biodegradable Zn-0.4Li alloys have been considered as medical implants due to their excellent mechanical properties and desirable biocompatibility. In this work, anodization was applied to modified corrosion resistance of the Zn-0.4Li alloy by forming a uniform and neat flower-like nanowire coating on the surface. After anodization for 7 min, the anodized Zn-0.4Li alloy had a yield strength of 253.6 MPa, ultimate tensile strength of 389.5 MPa, and elongation at a break of 66.0%. The corrosion rate of the Zn-0.4Li-7 min sample reached 0.5741 mm/y in the SBF, which was almost 18 times higher than that of the Zn-0.4Li alloy. The anodized Zn-0.4Li alloy exhibited higher antibacterial properties than that of the Zn-0.4Li alloy against Escherichia coli and Staphylococcus aureus . These results suggested that anodization may be an effective method to modulate the corrosion behavior of zinc alloys, which can be applied in the surface modification of biodegradable implants.

LM5 alloy is suitable for metal castings for marine and aesthetic uses due to its admirable resistance to corrosion. In order to make intricate shapes in the LM5 alloy, this study intends to assess the impact of Wire Electric Discharge Machining process variables, like Pulse on Time (Ton), Pulse off Time (Toff), Gap Voltage (GV) and Wire Feed (WF) on responses like Material Removal Rate (MRR), Surface Roughness (SR), and Kerf Width (Kw). The LM5 aluminium alloy plate was produced through stir casting process. SEM, EDAX and XRD images confirm the LM5 Al alloy's microstructure and crystal structure. WEDM studies were conducted using design of experiments approach based on L9 orthogonal array and analysed using Taguchi's Signal to Noise Ratio (S/N) analysis. Pulse on Time has the greatest statistical effects on MRR (68.25%), SR (79.46%) and kerf (81.97%). In order to assess the surface integrity of the WEDM machined surfaces, the SEM study on the topography was conducted using the optimum surface roughness process variables: Ton 110 μs, Toff 50 μs, GV 40 V, and WF 9 m/min. SEM images show the recast layer and its thickness. The average absolute error for MRR is 1.69%, SR is 3.89% and kerf is 0.88%, based on mathematical (linear regression) models. The Taguchi's Signal to Noise ratio analysis is the most appropriate for single objective optimization of responses., Competing Interests: The authors have declared that no competing interests exist., (Copyright: © 2024 Juliyana et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.)

Background: Manually bent, standard-of-care, Ti-6Al-4V, mandibular graft fixation devices are associated with a significant post-operative failure rate. These failures require the patient to endure stressful and expensive re-operation. The approach recommended in this report demonstrates the optimization of graft fixation device mechanical properties via "stiffness-matching" by varying the fixation device's location, shape, and material composition through simulation of the device's post-operative performance. This provides information during pre-operative planning that may avoid future device failure. Optimized performance may combine translation of all loading into compression of the bone graft with the adjacent bone segments and elimination or minimization of post-healing interruption of normal stress-strain (loading) trajectories., Results: This study reports a sheep mandibular graft model where four animals received virtually optimized, experimental nickel-titanium (NiTi) fixation plates fabricated using laser beam powder bed fusion (LPBF) additive manufacturing (AM). The last animal, our control, received a standard-of-care, manually bent, Ti-6Al-4V (aka Ti64) fixation plate. A 17.5-mm mandibular graft healed completely in all four animals receiving the experimental device. Experimental NiTi-implanted sheep experienced mandibular bone healing and restoration. The Ti64 plate, in the control animal, fractured and dislocated shortly after being implanted., Conclusion: The use of stiffness-matched implants, by means of plate material (NiTi) and geometry (porosity) enhanced bone healing and promoted better load transfer to the healed bone when compared to the bulk Ti64 found in the fixation plate that the Control animal received. The design technique and screw orientation and depth planning improved throughout the study leading to more rapid healing. The large animal model reported here provides data useful for a follow-on clinical trial., (© 2024. The Author(s).)

Implant surgeries are increasingly challenging due to their rising number. Achieving the desired biomaterial surface properties to ensure a strong bond with human tissue is a significant issue. This study investigates the influence of ultrasound (US) during the micro-arc oxidation (MAO) process on Ti13Zr13Nb bio-alloy, an area not previously explored, to enhance titanium alloy coatings' properties for biomedical applications. Porous calcium-phosphate-based coatings were successfully deposited on Ti13Zr13Nb using MAO and ultrasound micro-arc oxidation (UMAO). Various properties such as morphology, chemical composition, topography, wettability, surface free energy, thickness, adhesion to the substrate, as well as mechanical and corrosion characteristics were thoroughly analyzed. Cytocompatibility was assessed using human osteoblasts. Using US during the MAO process increased coating roughness (up to ~ 17%), core height (up to 22%), isotropy (up to 17%), thickness (up to ~ 46%), and hardness (up to ~ 18%), depending on MAO parameters and US mode. Optimal coating performance was achieved at 136 mA, 600 s, and a sinusoidal US setting, resulting in the highest isotropy (~ 79%) and rutile quantity (2.6%), the lowest elastic modulus (~ 57 GPa), and the contact angle of ~ 70°, all of which could have contributed to enhancing osteoblast viability in vitro. This study, for the first time, underscores the importance of using the US during the MAO in tailoring the Ti13Zr13Nb for specific biomedical applications., (© 2024. The Author(s).)

Most of published research on magnetic hyperthermia focused on iron oxides, ferrites, and binary alloy nanostructures, while the ternary alloys attracted much limited interest. Herein, we prepared NiCuCo ternary alloy nanocomposites with variable compositions by mechanical alloying. Physical properties were fully characterized by XRD, Rietveld analysis, XPS, SEM/EDX, TEM, ZFC/FC and H-M loops. DFT calculations were used to confirm the experimental results in terms of structure and magnetism. The results showed that the fabricated nanoalloys are face centered cubic (FCC) with average core sizes of 9-40 nm and behave as superparamagnetic with saturation in the range 4.67-42.63 emu/g. Langevin fitting corroborated the superparamagnetic behavior, while law of approach to saturation (LAS) was used to calculate the magnetic anisotropy constants. Heating effciencies were performed under an alternating magnetic field (AMF, H 0  = 170 Oe and f = 332.5 kHz), and specific absorption rate (SAR) values were determined. The highest magnetic saturation (M s ), heating potentials, and SAR values were attained for Ni 35 Cu 30 Co 35 containing the lowest Cu but highest Ni and Co percentages, and the least for Ni 15 Cu 70 Co 15 . Importantly, the nanoalloys reached the required temperatures for magnetic hyperthermia (42 °C) in relatively short times. We also showed that heat dissipiation can be simply tuned by changing many parameters such as concentration, field amplitude, and frequency. Finally, cytotoxicity viability assays against two different breast cancer cell lines treated with Ni 25 Cu 50 Co 25 nanoalloy in the presence and absence of AMF were investigated. No significant decrease in cancer cell viability was observed in the absence of AMF. When tested against tumorigenic KAIMRC2 breast cancer cells under AMF, the NiCuCo nanoalloy was found to be highly potent to the cells (~ 2-fold enhancement), killing almost all the cells in short times (20 min) and clinically-safe AC magnetic fields. These findings strongly suggest that the as-prepared ternary NiCuCo nanoalloys hold great promise for potential magnetically-triggered cancer hyperthermia., (© 2024. The Author(s).)

Bone tissue engineering (BTE) strategies have been developed to address challenges in orthopedic and dental therapy by expediting osseointegration and new bone formation. In this study, we developed irregular porous Ti-6Al-4V scaffolds coated with reduced graphene oxide (rGO), specifically rGO-pTi, and investigated their ability to stimulate osseointegration in vivo . The rGO-pTi scaffolds exhibited unique irregular micropores and high hydrophilicity, facilitating protein adsorption and cell growth. In vitro assays revealed that the rGO-pTi scaffolds increased alkaline phosphatase (ALP) activity, mineralization nodule formation, and osteogenic gene upregulation in MC3T3-E1 preosteoblasts. Moreover, in vivo transplantation of rGO-pTi scaffolds in rabbit calvarial bone defects showed improved bone matrix formation and osseointegration without hemorrhage. These findings highlight the potential of combining rGO with irregular micropores as a promising BTE scaffold for bone regeneration.

This study aimed to investigate adhesive shear bond strength (SBS) on an ultrafine-grained niobium alloy (UFG-Nb) that is a potential dental implant material. SBS of three adhesive systems combined with three composites to UFG-Nb was compared to corresponding SBS to Ti-6Al-4V and to zirconia. Specimens of the substrates UFG-Nb, Ti-6Al-4V and zirconia with plane surfaces were sandblasted with Al 2 O 3 , cleaned and dried. Three adhesive systems (Futurabond U, Futurabond M + , Futurabond M + DCA; all VOCO GmbH, Cuxhaven, Germany) were applied each on specimens of each substrate and light cured. One composite (BifixSE, BifixQM, GrandioSO; all VOCO GmbH) was applied and light cured resulting in 27 groups (n = 10) for all substrate-adhesive-composite-combinations. SBS was measured after 24 h of storage. To simulate aging equally prepared specimens underwent 5000 thermocycles before SBS measurement. There was no significant difference in SBS within the non-aged groups. Among the artificially aged groups, GrandioSO-groups showed a greater variance of SBS than the other composites. All significant differences of corresponding UFG-Nb-, Ti-6Al-4V- and zirconia-groups with same adhesive-composite-combination (ACC) were observed between UFG-Nb and zirconia or Ti-6Al-4V and zirconia but never between the two metallic substrates. The similarity between these materials might show in their adhesive bonding behavior. As there were no differences comparing corresponding groups prior to and after artificial aging, it can be concluded that aging does not affect SBS to UFG-Nb, Ti-6Al-4V and zirconia using the tested ACCs. Adhesive bonding of established ACCs to UFG-Nb is possible resulting in SBS comparable to those on Ti-6Al-4V and zirconia surfaces., (© 2024. The Author(s).)

Tibial fractures account for approximately 15% of all fractures, typically resulting from high-energy trauma. A critical surgical approach to treat these fractures involves the fixation of the tibia using a plate with minimally invasive osteosynthesis. The selection and fixation of the implant plate are vital for stabilizing the fracture. This selection is highly dependent on the plate's stability, which is influenced by factors like the stresses generated in the plate due to the load on the bone, as well as the plate's length, thickness, and number of screw holes. Minimizing these stresses is essential to reduce the risk of implant failure, ensuring optimal stress distribution and promoting faster, more effective bone healing. In the present work, the finite element and statistical approach was used to optimize the geometrical parameters of the implant plate made of SS 316L steel and Ti6Al4V alloy. A 3D finite element model was developed for analyzing the stresses and deformation, and implant plates were manufactured to validate the results with the help of an experiment conducted on the universal testing machine. A strong correlation was observed between the experimental and predicted results, with an average error of 8.6% and 8.55% for SS316L and Ti6Al4V alloy, respectively. Further, using the signal-to-noise ratio for the minimum stress condition was applied to identify the optimum parameters of the plate. Finally, regression models were developed to predict the stresses generated in SS316L and Ti6Al4V alloy plates with different input conditions. The statistical model helps us to develop the relation between different geometrical parameters of the Tibia implant plate. As determined by the present work, the parameter most influencing is implant plate length. This outcome will be used to select the implant for a specific patient, resulting in a reduction in implant failure post-surgery., (© 2024 IOP Publishing Ltd. All rights, including for text and data mining, AI training, and similar technologies, are reserved.)

Herein, a novel FeCoNi(b)-800 ternary metal nanoalloy was uniformly mixed with reduced graphene oxide (RGO) to synthesize the FeCoNi(b)-800@RGO(2:1) composite. The addition of RGO not only stopped the accumulation of FeCoNi(b)-800 alloy, but also heightened the electrocatalytic activity of composite. Particularly, the FeCoNi(b)-800@RGO(2:1) composite displayed the significantly strong electrocatalytic capacity for the reduction of roxarsone (ROX). Furthermore, the FeCoNi(b)-800@RGO(2:1) composite possessed enough porosity and metal catalytic sites, facilitating the transport and electrochemical reduction of the ROX. Thus, the FeCoNi(b)-800@RGO(2:1) composite modified glassy carbon electrode (FeCoNi(b)-800@RGO(2:1)/GCE) showed the superb electrochemical detection effect for ROX with relatively wide working range (0.1-1500 μM) and low detection limit (0.013 μM). Importantly, the FeCoNi(b)-800@RGO(2:1)/GCE sensor could accurately determine the contents of ROX in actual pork, chicken, duck and egg samples, indicating that it had good suitability in food safety monitoring., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Pure zinc exhibits low mechanical properties, making it unsuitable for use in guided bone regeneration (GBR) membranes. The present study focused on the preparation of Zn alloy GBR films using powder metallurgy, resulting in Zn-0.5Ti-0.5Fe and Zn-0.5Ti-0.5Mg alloy GBR films. The tensile strength of the pure Zn GBR film measured 85.9 MPa, while an elongation at break was 13.5%. In contrast, Zn-0.5Ti-0.5Fe and Zn-0.5Ti-0.5Mg alloy GBR films demonstrated significantly higher tensile strengths of 145.3 and 164.4 MPa, respectively, whereas elongations at break were 30.2% and 19.3%. The addition of Ti, Fe, and Mg substantially enhanced the mechanical properties of the zinc alloys. Corrosion analysis revealed that Zn-0.5Ti-0.5Fe and Zn-0.5Ti-0.5Mg alloy GBR membranes exhibited corrosion potentials of -1.298 and -1.316 V, respectively, with corresponding corrosion current densities of 12.11 and 13.32 μA/cm 2 . These values were translated to corrosion rates of 0.181 and 0.199 mm/year, indicating faster corrosion rates compared to pure Zn GBR membranes, which displayed a corrosion rate of 0.108 mm/year. Notably, both Zn-based alloy GBR membranes demonstrated excellent cytocompatibility, with a cytotoxicity rating of 0-1 in 25% leachate. Additionally, these membranes exhibited favorable osteogenic ability, as evidenced by the quantitative bone volume/tissue volume ratios (BV/TV) of new bone formation, which reached 30.3 ± 1.4% and 65.5 ± 1.8% for the Zn-0.5Ti-0.5Fe and Zn-0.5Ti-0.5Mg alloy GBR membranes, respectively, after 12 weeks of implantation. These results highlighted the significant potential for facilitating new bone growth. The proposed Zn-0.5Ti-0.5Fe and Zn-0.5Ti-0.5Mg alloy GBR membranes showed promise as viable biodegradable materials for future clinical studies.

A scaffold is a three-dimensional porous structure that is used as a template to provide structural support for cell adhesion and the formation of new cells. Metallic cellular scaffolds are a good choice as a replacement for human bones in orthopaedic implants, which enhances the quality and longevity of human life. In contrast to conventional methods that produce irregular pore distributions, 3D printing, or additive manufacturing, is characterized by high precision and controlled manufacturing processes. AM processes can precisely control the scaffold's porosity, which makes it possible to produce patient specific implants and achieve regular pore distribution. This review paper explores the potential of Ti-6Al-4V scaffolds produced via the SLM method as a bone substitute. A state-of-the-art review on the effect of design parameters, material, and surface modification on biological and mechanical properties is presented. The desired features of the human tibia and femur bones are compared to bulk and porous Ti6Al4V scaffold. Furthermore, the properties of various porous scaffolds with varying unit cell structures and design parameters are compared to find out the designs that can mimic human bone properties. Porosity up to 65% and pore size of 600 μm was found to give optimum trade-off between mechanical and biological properties. Current manufacturing constraints, biocompatibility of Ti-6Al-4V material, influence of various factors on bio-mechanical properties, and complex interrelation between design parameters are discussed herein. Finally, the most appropriate combination of design parameters that offers a good trade-off between mechanical strength and cell ingrowth are summarized., (© 2024 IOP Publishing Ltd. All rights, including for text and data mining, AI training, and similar technologies, are reserved.)

High entropy alloys and amorphous metallic alloys represent two distinct classes of advanced alloy materials, each with unique structural characteristics. Their emergence has garnered considerable interest across the materials science and engineering communities, driven by their promising properties, including exceptional strength. However, their extensive compositional diversity poses substantial challenges for systematic exploration, as traditional experimental approaches and high-throughput calculations struggle to efficiently navigate this vast space. While the recent development in data-driven materials discovery could potentially help, such efforts are hindered by the scarcity of comprehensive data and the lack of robust predictive tools that can effectively link alloy composition with specific properties. To address these challenges, we have deployed a machine-learning-based workflow for feature selection and statistical analysis to afford predictive models that accelerate the data-driven discovery and optimization of these advanced materials. Our methodology is validated through two case studies: (i) a regression analysis of the bulk modulus, and (ii) a classification analysis based on glass-forming ability. The Bayesian-optimized regression model trained for the prediction of bulk modulus achieved an R 2 of 0.969, an mean absolute error (MAE) of 3.958 GPa, and an root mean square error (RMSE) of 5.411 GPa, while our classification model for predicting glass-forming ability achieved an F1-score of 0.91, an area-under-the-curve of the receiver-operating-characteristic curve of 0.98, and an accuracy of 0.91. Furthermore, by leveraging a wide array of chemical data from diverse literature sources, we have successfully predicted a broad range of properties. This success underscores the efficacy of our modeling approach and emphasizes the importance of a comprehensive feature analysis and judicious feature selection strategy over a mere reliance on complex modeling techniques.

The implications of retained strain on in vitro and in vivo degradation behavior as well as cytocompatibility of the Mg-4Zn-0.5Ca-0.8Mn alloy is comprehensively studied. The retained strain is induced in homogenized specimens by hard-plate hot forging (HPHF) at a temperature (523 K) lower than the recrystallization temperature of the alloy. The retained strain generated during deformation process deteriorated the corrosion response of the deformed alloy as compared to its homogenized counterpart. The strained area of deformed specimen with high dislocation density promoted defect generation (oxygen vacancies) in the film and facilitated preferential migration of ions, consequently leading to formation of a nonuniform product film with low protectiveness. In addition to strain magnitude, the distribution of retained strain also influenced the product film properties in the deformed specimens. An even distribution of retained strain improved the uniformity of the product film to certain extent by providing greater film coverage, resulting in higher film resistance. After 24 h of immersion, the protectiveness of the film was further improved in this specimen due to annihilation of defects through homogeneous ionic migration, which led to the development of a uniform and stable film that restricted further ionic diffusion. The dissolution of Zn(OH) 2 into Zn 2+ ions was promoted at lower pH, resulting in enhanced antimicrobial activity in the specimen with the lowest degradation. Besides, the specimen with stable product film not only minimized the rate of further degradation but also served as an interface for new bone growth, as evident from in vivo studies.

Metallic biomaterials, including traditional bioinert materials (such as stainless steel, cobalt-chromium alloys, pure titanium, and titanium alloys), novel biodegradable metals (such as pure magnesium and magnesium alloys, pure zinc and zinc alloys, and pure iron and iron alloys), and biomedical metallic glasses, have been widely used and studied as various biomedical implants and devices. Many scientists and researchers have investigated their superior biomechanical properties, corrosion behavior, and biocompatibility. However, their surface characteristics are of extreme importance due to continuing interactions between the surface/interface of an implanted metallic biomaterial and the surrounding physiological environment. Surface morphologies on these metallic biomaterials can modulate their in vitro and in vivo biological responses. In this review, we have summarized and investigated the effect of various surface morphologies on the corrosion behavior, cellular response, antibacterial activity, and osteogenesis of biomedical metallic materials. In addition, future research directions and challenges of surface morphologies on biomedical metallic materials have been elaborated. This review can lay a theoretical and practical foundation for further research and development on biomedical metallic materials.

Scaffolds play a crucial role in bone tissue engineering to support the defect area through bone regeneration and defect reconstruction. Promising tissue regeneration without negative repercussions and avoidance of the lifelong presence inside the body make bioresorbable metals prosper in the field of regenerative medicine. Recently, Zn and its alloys have emerged as promising biodegradable materials for their moderate degradation rate and satisfactory biocompatibility. Nevertheless, it is very challenging for cells to adhere and grow over the Zn surface alone, which influences the tissue-implant integration. In this study, an attempt has been made to systematically investigate the bioactivity responses in terms of in vitro hemocompatibility, cytotoxicity, antibacterial activity, and in vivo biocompatibility of newly developed Zn-2Cu-0.5Mn/Mg alloy scaffolds with different surface roughness. The rough surface of Zn-2Cu-0.5Mg shows the highest degradation rate of 0.16 mm/yr. The rough surface exhibits a prominent role in the adsorption of protein, further enhancing cell adhesion. Concentration-dependent alloy extract shows the highest cell proliferation for 12.5% of the extract with a maximum cell viability of 101% in Zn-2Cu-0.5Mn and 108% in Zn-2Cu-0.5Mg after 3 d. Acceptable hemolysis percentages (less than 5%) with promising anticoagulation properties are observed for all of the conditions. Enhanced antibacterial ( Staphylococcus aureus and Escherichia coli ) activity due to a significant effect of ions illustrates the maximum killing effect on the bacterial colony for the rough Zn-2Cu-0.5Mg alloy. In addition, it is observed that for rough Zn-2Cu-0.5Mn/Mg alloys, the inflammatory response is minimal after subcutaneous implantation, and neo-bone tissue forms in the defect areas of the rat femur with satisfactory biosafety response. The osseointegration property of the Zn-2Cu-0.5Mg alloy is comparable to that of the Zn-2Cu-0.5Mn alloy. Therefore, the rough surface of the Zn-2Cu-0.5Mg alloy has the potential to enhance biocompatibility and promote better osseointegration activity with host tissues for various biomedical applications.

With the accelerating trend of global aging, bone damage caused by orthopedic diseases, such as osteoporosis and fractures, has become a shared international event. Traffic accidents, high-altitude falls, and other incidents are increasing daily, and the demand for bone implant treatment is also growing. Although extensive research has been conducted in the past decade to develop medical implants for bone regeneration and healing of body tissues, due to their low biocompatibility, weak bone integration ability, and high postoperative infection rates, pure titanium alloys, such as Ti-6A1-4V and Ti-6A1-7Nb, although widely used in clinical practice, have poor induction of phosphate deposition and wear resistance, and Ti-Zr alloy exhibits a lack of mechanical stability and processing complexity. In contrast, the Ti-Ni alloy exhibits toxicity and low thermal conductivity. Nonthermal plasma (NTP) has aroused widespread interest in synthesizing and modifying implanted materials. More and more researchers are using plasma to modify target catalysts such as changing the dispersion of active sites, adjusting electronic properties, enhancing metal carrier interactions, and changing their morphology. NTP provides an alternative option for catalysts in the modification processes of oxidation, reduction, etching, coating, and doping, especially for materials that cannot tolerate thermodynamic or thermosensitive reactions. This review will focus on applying NTP technology in bone implant material modification and analyze the overall performance of three common types of bone implant materials, including metals, ceramics, and polymers. The challenges faced by NTP material modification are also discussed.

Titanium and its alloys, especially Ti-6Al-4V, are widely studied in implantology for their favorable characteristics. However, challenges remain, such as the high modulus of elasticity and concerns about cytotoxicity. To resolve these issues, research focuses on β-type titanium alloys that incorporate elements such as Mo, Nb, Sn, and Ta to improve corrosion resistance and obtain a lower modulus of elasticity compatible with bone. This review comprehensively examines current β titanium alloys, evaluating their mechanical properties, in particular the modulus of elasticity, and corrosion resistance. To this end, a systematic literature search was carried out, where 81 articles were found to evaluate these outcomes. In addition, this review also covers the formation of the alloy, processing methods such as arc melting, and its physical, mechanical, electrochemical, tribological, and biological characteristics. Because β-Ti alloys have a modulus of elasticity closer to that of human bone compared to other metal alloys, they help reduce stress shielding. This is important because the alloy allows for a more even distribution of forces by having a modulus of elasticity more similar to that of bone. In addition, these alloys show good corrosion resistance due to the formation of a noble titanium oxide layer, facilitated by the incorporation of β stabilizers. These alloys also show significant improvements in mechanical strength and hardness. Finally, they also have lower cytotoxicity and bacterial adhesion, depending on the β stabilizer used. However, there are persistent challenges that require detailed research in critical areas, such as optimizing the composition of the alloy to achieve optimal properties in different clinical applications. In addition, it is crucial to study the long-term effects of implants on the human body and to advance the development of cutting-edge manufacturing techniques to guarantee the quality and biocompatibility of implants.

In this study, molecular dynamics (MD) simulations were used to investigate how alloying tungsten (W) with molybdenum (Mo) and local strain affect the primary defect formation and interstitial dislocation loops (IDLs) in W-Mo alloys. While the number of Frenkel pairs (FPs) in the W-Mo alloy is similar to pure W, it is half that of pure Mo. The W-20% Mo alloy, chosen for further analysis, showed minimal FP variance after collision cascades induced by primary knock-on atoms (PKAs) at 10 to 80 keV. The research examined hydrostatic strains from -1.4% to 1.6%, finding that higher strains correlated with increased FP counts and cluster formation, including IDLs. The following two types of IDLs were identified: majority ½ <111> loops as well as <100> IDLs that formed within the initial picoseconds of the simulations under higher tensile strain (1.6%) and larger PKA energies (80 keV). The strain effects also correlated with changes in threshold displacement energy (TDE), with higher FP formation under tensile strain. This study highlights the impact of strain and alloying on radiation damage, particularly in low-temperature, high-energy environments.

Bone defect repair and postoperative infections are among the most challenging issues faced by orthopedic surgeons. Thus, the antibacterial agent Cu and the osteogenic promoter Sr have been widely incorporated into biodegradable alloys separately. However, to the best of our knowledge, the synergistic effects of Cu and Sr on zinc alloys have not been investigated. Therefore, we have developed a series of novel Zn-4Cu-xSr (x = 0.05, 0.1, and 0.3 wt %) alloys. Our results showed that the addition of Cu and Sr significantly increased the strength of pure zinc while maintaining a certain level of ductility. Plastic deformation further enhanced the strength and ductility of the alloys. The tensile strength of HR Zn-4Cu-xSr alloys remains between 233.34 ± 1.31 MPa and 235.81 ± 3.0 MPa, with elongation values ranging from 45.7 ± 1.56% to 49.6 ± 6.22%. The HE Zn-4Cu-0.05Sr alloy exhibits a high elongation of 95.05 ± 11.1%. Furthermore, the HE Zn-4Cu-0.1Sr alloy demonstrates the best overall mechanical performance with ultimate tensile strength ( σ uts ), yield strength ( σ ys ), and elongation (ε) values of 252.73 ± 0.12 MPa, 181.0 ± 0.79 MPa, and 42.8 ± 1.13%, respectively. The corrosion rate of HE Zn-4Cu-xSr alloys increases with an increase in Sr content. All samples exhibit satisfactory cytocompatibility with the cells displaying a healthy spindle-like morphology. In vitro antibacterial tests show that the HE Zn-4Cu-xSr alloys exhibit significant antibacterial effects against Staphylococcus aureus ( S. aureus ) and Escherichia coli ( E. coli ), with the antibacterial properties strengthening as the Sr content increases. Therefore, this study demonstrates the tremendous potential application of Zn-4Cu-xSr alloys in biodegradable zinc alloys for bone fracture fixation and repair.

With the e-waste growing rapidly all over the globe due to growing demand of electronics, smartphones, etc., coming up with an efficient and sustainable recycling process is the need of the hour. The present work reports a novel and sustainable process of manufacturing Ni alloy by bringing together three major waste streams such as waste Ni-MH batteries, e-waste plastics, and waste glass. The chosen temperature (1550 °C) favours the reduction of nickel-oxide by e-waste plastic as the reductant and sends rare earth elements present in the waste Ni-MH battery as oxide mixture to the slag phase. Waste glass powder used in this process functions as the fluxing agent, hence not requiring any additional flux. The reduction mechanism is gas-based, controlled mainly by hydrogen and carbon monoxide gases released as a result of decomposition of e-waste plastic as reaction commenced from cold zone (∼300 °C) to hot zone (1550 °C) in the horizontal tubular furnace. Formation of nickel alloy and enrichment of slag with mixture of rare earth oxides were confirmed by XRD, SEM-EDS, and Rietveld refining analysis performed on the XRD spectra of slag phase. ICP-OES (Inductively coupled plasma optical emission spectroscopy) and LIBS (laser induced breakdown spectrometer KT-100S) confirmed the high metal content in the alloy, thereby emphasizing the purity (∼98%) which is close to the composition of nickel super alloy. A maximum of 61% by weight REO enrichment was achieved in the slag phase, having La 2 O 3 :44.6%, Pr 2 O 3 :14.8%, and Nd 2 O 3 : 1.6% under optimised experimental conditions (1550 °C, 15 min, and 20% waste glass powder). This scientific investigation evinces a promising route for efficient utilisation of waste streams emanating from e-waste, thereby devising a sustainable recycling technique and protecting the environment, too., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

For designing the assistive wearable rehabilitation robots, it is challenging to design the robot as energy efficient because the actuators have to be capable of overcoming human loads such as gravity of the body and spastic torque continuously during the assistance. To address these challenges, we propose a novel design of soft artificial muscle that utilizes shape memory alloy (SMA) spring actuators with pre-detwinning process. The SMA spring was fabricated through a process called pre-detwinning, which enhances the linearity of the SMA spring in martensite phase and unpowered restoring force, which is called passive force. The fabricated SMA spring can contract >60%. Finally, the soft wearable robot that can assist not only the gravitational torque exerted on the elbow by passive force, but also the elbow movements with active force was designed with a soft artificial muscle. A soft artificial muscle consists of the bundles of pre-detwinned SMA springs integrated with the stretchable coolant vessel. The stiffness of the muscle was measured as 1125 N/m in martensite phase and 1732 N/m in austenite phase. In addition, the muscle showed great actuation frequency performances, the bandwidth of which was measured as 0.5 Hz. The proposed wearable mechanism can fully compensate the gravitational torque for all the angles in passive mode. In addition, the proposed mechanism can produce high torque up to 3.5 Nm and movements in active mode.