Search

Drinking water defluoridation has attracted significant attention in the scientific community, from which membrane technology, by exploring thin film nanocomposite (TFN) membranes, has demonstrated a great potential for treating fluoride-contaminated water. This study investigates the development of a TFN membrane by integrating titanium oxide nanosheets (TiO 2 NSs) into the polyamide (PA) layer using interfacial polymerization. The characterization results suggest that successfully incorporating TiO 2 NSs into the PA layer of the TFN membrane led to a surface with a high negative charge, hydrophilic properties, and a smooth surface at the nanoscale. The TFN membrane, containing 80 ppm of TiO 2 NSs, demonstrated a notably high fluoride rejection rate of 98%. The Donnan-steric-pore-model-dielectric-exclusion model was employed to analyze the effect of embedding TiO 2 NSs into the PA layer of TFN on membrane properties, including charge density (X d ), the pore radius (r p ), and pore dielectric constant (ε p ). The results indicated that embedding TiO 2 NSs increased X d and decreased the εp by less than the TFC membrane without significantly affecting the r p . The resulting TFN membrane demonstrates promising potential for application in water treatment systems, providing an effective and sustainable solution for fluoride remediation in drinking water., Competing Interests: The authors state that none of the work disclosed in this study could have been influenced by any known conflicting financial interests or personal relationships.

This paper addresses a retrofitting vacuum membrane distillation (VMD) setup to reduce the accumulated pressure inside the permeated side. This modification is necessary to extend the operation of the VMD to extreme operation conditions of higher hot water temperatures. This modification, denoted as a hybrid configuration, proposes the injection of a cold water stream into the VMD cell without mixing it with the permeate. Energy and exergy efficiency analyses were performed to assess the effectiveness of the hybrid configuration. The performance of the modified system indicated an improvement in terms of permeate flux (J), the gain output ratio (GOR), and the utilitarian exergetic efficiency (η ex,u ), which reach up to two and three times that of the base configuration of the VMD system. However, the exergetic efficiency (η ex ) of the hybrid system showed marginal improvement compared to the base case over the tested range of hot water temperatures. This is because the enhanced vapor production is penalized by excess energy consumption. Moreover, the highest exergy destruction percentages occurred in the operational components (e.g., heater and chillers) which fall in the range of 19.0-68.9%. The exergy destruction percentage in the original components (e.g., the VMD cell and condenser) did not exceed 8.3%. Furthermore, this study indicated that the hybrid configuration requires additional tuning and optimization to perform efficiently over wide operating conditions.

The current study focuses on the development of a superhydrophobic poly(vinylidene fluoride-cohexafluoropropylene) nanocomposite membrane suitable for vacuum membrane distillation by incorporating SiO 2 nanoparticles. At loading hydrophobic nano-SiO 2 particle concentration (0.50-1.50 wt.%), the developed nanocomposite membranes are optimized in terms of vacuum membrane distillation performance. The influence of temperature, vacuum pressure, and feed water flow is studied for desalinating high-salinity brine. The results show that the developed vacuum distillation membrane is capable of 95% salt rejection during the treatment of a highly saline feed (65,000 ppm) at fixed flow rates of 120 L/h saline feed and different operating conditions consisting of feed inlet temperatures ranging from 40°C to 70°C and distillate inlet temperatures of 7-15°C. The vacuum membrane distillation process achieves 0.38-1.66% water recovery with increasing concentration factor, meaning that recovery is increased, and shows a specific electrical energy consumption of 5.16-23.90 kWh/m 3 for product water. Overall, the newly designed membrane demonstrates suitability for a vacuum membrane distillation system. PRACTITIONER POINTS: Desalinate high-salinity brine (TDS > 35,000 ppm) using a vacuum membrane distillation system. A hydrophobic PVDF-HFP/SiO 2 nanocomposite membrane development for vacuum membrane distillation. A newly designed single vacuum membrane distillation system for RO brine treatment., (© 2024 Water Environment Federation.)

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques including XPS, FTIR, SEM, TGA, and zeta potential analysis are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

This study addresses the significant concern of pharmaceutical contaminants, including antipyretic and antibiotic drugs, in municipal and industrial wastewater, impacting both the environment and human health. We investigate incorporating zinc-based metal-organic framework (Zn-MOF) nanofillers into polyamide layers, developing thin-film composite (PA-TFC) nanofiltration membranes via interfacial polymerization to remove paracetamol, ibuprofen, and amoxicillin from simulated wastewater. Characterization confirms Zn-MOF's presence in the PA-TFC membrane, affecting structural topology, pore size, contact angles, and zeta potential. Zn-MOF nanofillers strongly adhere to the polyamide layer, influencing membrane surface chemistry and morphology. The newly developed MOF/PA-TFC nanofiltration membranes demonstrate a remarkable water flux of up to 35 LMH, showcasing superior removal efficiency for the three pharmaceutical contaminants when compared to PA-TFC membranes. Specifically, the rejection rates for paracetamol, ibuprofen, and amoxicillin are notably high at 93%, 98%, and 99%, respectively. Consequently, this study establishes MOF/PA-TFC nanofiltration membranes as a highly efficient solution for removing emerging pharmaceutical contaminants from environmental water, promoting sustainability and safeguarding water resources., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

A biopolymer-based adsorbent comprising chitosan (CS) and κ-carrageenan (κ-Carr) was synthesised and evaluated to treat phenolic-contaminated water. The developed CS/κ-Carr hydrogel demonstrated excellent performance with a phenol adsorption uptake of 80 %. The morphologies of CS/κ-Carr hydrogels with different ratios of CS to κ-Carr ranging from 1:2 to 7:3 were characterised using scanning electron microscopy and atomic force microscopy; their chemical structures were investigated by spectral analyses using Fourier-transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry; their adsorption characteristics were determined using tests for swelling, chemical stability, hygroscopic moisture content, and hydrophilicity. Finally, a batch-type evaluation method demonstrated adsorption performance at 25 °C and pH 6.9. Adsorption isotherms and kinetic data were successfully obtained using the Freundlich and pseudo-second-order models, respectively. The results indicate that one-pot synthesis of an insoluble CS/κ-Carr hydrogel adsorbent exhibits considerable potential for the removal of phenol from aqueous solutions, providing an environmentally friendly technology enhancing the phenol adsorption performance of CS., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

This study focuses on the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO 2 ) nanoparticles through the phase inversion technique. Advanced tools and methods were employed to systematically evaluate the properties and performance of the newly developed membranes. The investigation primarily centered on the impact of TiO 2 addition in the SPPSu inner layer on pure water permeability and salt rejection. The nanocomposite membranes exhibited a remarkable three-fold increase in pure water permeability, achieving a flux of 5.4 L/m 2 h.bar compared to pristine membranes. The addition of TiO 2 also enhanced the mechanical properties, with an expected tensile strength increase from 2.4 to 3.9 MPa. An evaluation of salt rejection performance using a laboratory-scale filtration setup revealed a maximal rejection of 95% for Mg 2 SO 4 , indicating the effective separation capabilities of the modified dual-layer hollow fiber nanocomposite membranes for divalent ions. The successful synthesis and characterization of these membranes highlight their potential for nanofiltration processes, specifically in selectively separating divalent ions from aqueous solutions, owing to their improved pure water flux, mechanical strength, and salt rejection performance.

The acid-mediated (oxalic acid [OXA], cinnamic acid [CA], and itaconic acid [IA]) SnO 2 nanorods were synthesized by the hydrothermal method. The synthesized SnO 2 nanorods, in turn, were analyzed with various physico-chemical techniques such as the X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), and Raman spectroscopy. Furthermore, the photocatalytic activity of the different SnO 2 nanorods was investigated with the malachite green (MG) dye under visible light illumination. The OXA-SnO 2 nanorods displayed an excellent degradation performance with observed value at 91% and it was compared to CA and IA-SnO 2 nanomaterials. This tetragonal phase was identified and confirmed by XRD studies. In this regards, obtained band gap energy is low then optimally performed to the photocatalytic evolution. The OXA-SnO 2 materials were tested for antibacterial and antifungal studies; this was as shown in good biological activities with admire to the different bacterial strains. The Candida albicans (antifungal) and Enterococcus faecalis (Gram-positive) bacteria were not affected in the microbial studies., (© 2021. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Incense sticks ash is one of the most unexplored by-products generated at religious places and houses obtained after the combustion of incense sticks. Every year, tonnes of incense sticks ash is produced at religious places in India which are disposed of into the rivers and water bodies. The presence of heavy metals and high content of alkali metals challenges a potential threat to the living organism after the disposal in the river. The leaching of heavy metals and alkali metals may lead to water pollution. Besides this, incense sticks also have a high amount of calcium, silica, alumina, and ferrous along with traces of rutile and other oxides either in crystalline or amorphous phases. The incense sticks ash, heavy metals, and alkali metals can be extracted by water, mineral acids, and alkali. Ferrous can be extracted by magnetic separation, while calcium by HCl, alumina by sulfuric acid treatment, and silica by strong hydroxides like NaOH. The recovery of such elements by using acids and bases will eliminate their toxic heavy metals at the same time recovering major value-added minerals from it. Here, in the present research work, the effect on the elemental composition, morphology, crystallinity, and size of incense sticks ash particles was observed by extracting ferrous, followed by extraction of calcium by HCl and alumina by H 2 SO 4 at 90-95 °C for 90 min. The final residue was treated with 4 M NaOH, in order to extract leachable silica at 90 °C for 90 min along with continuous stirring. The transformation of various minerals phases and microstructures of incense sticks ash (ISA) and other residues during ferrous, extraction, calcium, and alumina and silica extraction was studied using Fourier transform infrared (FTIR), dynamic light scattering (DLS), X-ray fluorescence (XRF), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and inductively coupled plasma-optical emission spectroscopy (ICP-OES). DLS was used for analyzing the size during the experiments while FTIR helped in the confirmation of the formation of new products during the treatments. From the various instrumental analyses, it was found that the toxic metals present in the initial incense sticks ash got eliminated. Besides this, the major alkali metals, i.e., Ca and Mg, got reduced during these successive treatments. Initially, there were mainly irregular shaped, micron-sized particles that were dominant in the incense sticks ash particles. Besides this, there were plenty of carbon particles left unburned during combustion. In the final residue, nanosized flowers shaped along with cuboidal micron-sized particles were dominant. present in If, such sequential techniques will be applied by the industries based on recycling of incense sticks ash, then not only the solid waste pollution will be reduced but also numerous value-added minerals like ferrous, silica, alumina calcium oxides and carbonates can be recovered from such waste. The value-added minerals could act as an economical and sustainable source of adsorbent for wastewater treatment in future., (© 2021. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Valorizing the fatty content of agricultural waste in material synthesis is an interesting topic. This work focused on utilizing oleic acid from the solid waste of olive mills in Saudi Arabia to synthesize biodegradable polyanhydrides based on sebacic acid which terminated with different concentrations of fatty acid (10, 30, 50, and 70 wt%), then characterize the final polymer samples and study the effects of termination on polyanhydrides properties, such as molecular weight and degradation profile. The fatty content of the solid waste was extracted, purified, and analyzed prior to and after separating the saturated and unsaturated fractions by urea crystallization, then the microwave-assisted melt polycondensation technique was used in the synthesis of the final polymers. Molecular weights were determined by gel permeation chromatography (GPC), and the degradation profile of the prepared samples was examined by determining the weight loss percentage of the polymer mass and FT-IR scanning for the anhydride bond before and after sample degradation. Results showed a linear degradation profile for most samples with no significant change in the molecular weights due to termination.

Polyphenylsulfone (PPSU) membranes are of fundamental importance for many applications such as water treatment, gas separation, energy, electronics, and biomedicine, due to their low cost, controlled crystallinity, chemical, thermal, and mechanical stability. Numerous research studies have shown that modifying surface properties of PPSU membranes influences their stability and functionality. Therefore, the modification of the PPSU membrane surface is a pressing issue for both research and industrial communities. In this review, various surface modification methods and processes along with their mechanisms and performance are considered starting from 2002. There are three main approaches to the modification of PPSU membranes. The first one is bulk modifications, and it includes functional groups inclusion via sulfonation, amination, and chloromethylation. The second is blending with polymer (for instance, blending nanomaterials and biopolymers). Finally, the third one deals with physical and chemical surface modifications. Obviously, each method has its own limitations and advantages that are outlined below. Generally speaking, modified PPSU membranes demonstrate improved physical and chemical properties and enhanced performance. The advancements in PPSU modification have opened the door for the advance of membrane technology and multiple prospective applications.

Nano-fibrillated cellulose (NFC) was extracted by a chemical method involving alkali and acid hydrolysis. The characterisation of the citrus sinensis fruit peel bran and nano-fibrillated cellulose was performed by XRD, FTIR, TEM, and FESEM. XRD confirmed the phase of NFC which showed monoclinic crystal with spherical to rod shape morphology with a size of 44-50 nm. The crystallinity index of treated NFC increased from 39% to 75%. FTIR showed the removal of lignin and hemicellulose from waste peels due to the alkaline treatment. Silver nanoparticles were also synthesised by utilizing extract of citrus sinensis skins as a reducing agent. Pharmaceutical effluent samples from an industrial area were tested by Atomic Absorption Spectrometry. Out of the four metals obtained, cadmium and chromium were remediated by silver nanoparticles with nano-fibrillated cellulose via simulated method in 100 mg/L metal-salt concentrations over a time period of 160 min. The highest removal efficiency was found for cadmium, i.e., 83%, by using silver and NFC together as adsorbents. The second highest was for chromium, i.e., 47%, but by using only NFC. The Langmuir and Freundlich isotherms were well fitted for the sorption of Cd (II) and Cr (II) with suitable high R 2 values during kinetic simulation. Thus, the isolation of NFC and synthesis of silver nanoparticles proved efficient for heavy metal sorption by the reuse of waste skins.

We fabricated a nanofiltration membrane consisting of a polyaniline (PANI) film on a polyphenylsulfone (PPSU) substrate membrane. The PANI film acted as a potent separation enhancer and antimicrobial coating. The membrane was analyzed via scanning electron microscopy and atomic force microscopy to examine its morphology, topography, contact angle, and zeta potential. We aimed to investigate the impact of the PANI film on the surface properties of the membrane. Membrane performance was then evaluated in terms of water permeation and rejection of methylene blue (MB), an organic dye. Coating the PPSU membrane with a PANI film imparted significant advantages, including finely tuned nanometer-scale membrane pores and tailored surface properties, including increased hydrophilicity and zeta potential. The PANI film also significantly enhanced separation of the MB dye. The PANI-coated membrane rejected over 90% of MB with little compromise in membrane permeability. The PANI film also enhanced the antimicrobial activity of the membrane. The bacteriostasis ( B R ) values of PANI-coated PPSU membranes after six and sixteen hours of incubation with Escherichia coli were 63.5% and 95.2%, respectively. The B R values of PANI-coated PPSU membranes after six and sixteen hours of incubation with Staphylococcus aureus were 70.6% and 88.0%, respectively.

In this study, for the first time, a highly permeable composite membrane was constructed by incorporating a zinc-based metal-organic framework (Zn-MOF) in a polyphenylsulfone matrix for the elevation of antifouling properties. Owing to the hydrophilic nature and high surface charge, this membrane demonstrated effective bovine serum albumin (a model protein) rejection and antifouling characteristics.

One of the main obstacles to studying the surface ultrastructure of microbial cells by atomic force microscopy (AFM) is determining how to immobilize live cells on the AFM substrates. Each method has its own advantages and disadvantages. The aim of this study was to characterize a new simple and inexpensive method using two types of polyethersulfone (PES) membrane filters that differ in pore size (micropore and nanopore) to immobilize live and dead Brevibacillus laterosporus for AFM imaging. B. laterosporus was easily trapped by the microporous PES membrane, facilitating the successful AFM scanning of the bacterial surface ultrastructure. In addition, B. laterosporus strongly attached to the nanoporous membranes and withstood the pulling forces exerted by the AFM tip during scanning. These methods of immobilization did not affect the cell viability. The nanostructure and roughness of the bacterial surface were also observed for live, fixed, and air-dried cells. Live and dead bacteria displayed similar morphologies at low resolution, while at high resolution, live bacteria displayed a more convoluted surface ("brain-like structure")., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

This work focuses on developing a novel method to optimize the fabrication conditions of polyamide (PA) thin film composite (TFC) membranes using the multi-objective genetic algorithm II (MOGA-II) method. We used different fabrication conditions for formation of polyamide layer-trimesoyl chloride (TMC) concentration, reaction time (t), and curing temperature (Tc)-at different levels, and designed the experiment using the factorial design method. Three functions (polynomial, neural network, and radial basis) were used to generate the response surface model (RSM). The results showed that the radial basis predicted good results (R 2 = 1) and was selected to generate the RSM that was used as the solver for MOGA-II. The experimental results indicate that TMC concentration and t have the highest influence on water flux, while NaCl rejection is mainly affected by the TMC concentration, t, and Tc. Moreover, the TMC concentration controls the density of the PA, whereas t confers the PA layer thickness. In the optimization run, MOGA-II was used to determine optimal parametric conditions for maximizing water flux and NaCl rejection with constraints on the maximum acceptable levels of Na 2 SO 4 , MgSO 4 , and MgCl 2 rejections. The optimized solutions were obtained for longer t, higher Tc, and different TMC concentration levels., Competing Interests: The authors declare no conflict of interest.

Biofouling is a serious issue in membrane-based water and wastewater treatment as it critically compromises the efficacy of the water treatment processes. This investigation demonstrates the antimicrobial and antifouling properties of a nanocomposite membrane system composed of carboxyl-functionalized graphene oxide (COOH-GO) and polyphenylsulfone (PPSU). The PPSU/COOH-GO nanocomposite membrane exhibited excellent antimicrobial properties, achieving maximum bacteriostasis rates of 74.2% and 81.1% against the representative Gram-negative bacteria (Escherichia coli and Pseudomonas aeruginosa, respectively) and 41.9% against the representative Gram-positive bacterium (Staphylococcus aureus). The PPSU/COOH-GO nanocomposite membrane inhibited the attachment, colonization, and the biofilm formation of three species. Antifouling was assessed through filtration experiments using a model foulant bovine serum albumin (BSA). The fouling mechanisms were investigated by Hermia's models (complete blocking, intermediate blocking, standard blocking, and cake formation), and the analysis involved fitting the volumetric flux decline experimental data to models. The fouling study revealed a less irreversible fouling and increased flux recovery ratio for the PPSU/COOH-GO nanocomposite membrane. Complete blocking of pores and cake formation were the major fouling mechanisms for the membrane.

Over the past few years, significant efforts have been made to create new fluorescent probes operating at longer wavelengths, particularly in the second near-infrared (NIR-II) window from 1000 to 1700 nm, offering enhanced tissue penetration compared to light in the visible and first near-infrared window (700-900 nm). However, most of the reported NIR-II fluorophores meet such dilemmas; they are excreted slowly and largely retained within the reticuloendothelial system. Here, we report a rapidly excreted NIR-II lanthanide complex Nd-DOTA (over 50% excreted through the kidneys within 3 h postinjection) with a molecular mass only 0.54 kDa. The NIR-II imaging quality of Nd-DOTA was far superior to that of clinically approved ICG with good photostability and deep tissue penetration (7 mm). Superior tumor-to-normal tissue ratio was successfully achieved to facilitate the abdominal ovarian metastases surgical delineation. Metastases with ≤1 mm can be completely excised under NIR-II bioimaging guidance. Significantly, since the Nd-DOTA structure is same to the clinically approved magnetic resonance imaging (MRI) contrast Gd-DOTA, it will speed up the clinical translation for this novel kind of NIR-II probes in the future.

In the present study, graphene oxide (GO) was incorporated as a nanoadditive into a polyphenylsulfone (PPSU) to develop a PPSU/GO nanocomposite membrane with enhanced antifouling properties. A series of membranes containing different concentrations (0.2, 0.5 and 1.0 wt.%) of GO were fabricated via the phase inversion method, using N-methyl pyrrolidone (NMP) as the solvent, deionized water as the non-solvent, and polyvinylpyrrolidone (PVP) as a pore forming agent. The prepared nanocomposite membranes were characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM), and were also characterized with respect to contact angle, zeta potential and porosity, mean pore radius, tortuosity and molecular weight cut-off (MWCO). Thermogravimetric analysis (TGA) and tensile testing were used to measure thermal and mechanical properties. The membrane performance was evaluated by volumetric flux and rejection of proteins, and antifouling properties. According to the results, the optimum addition of 0.5 wt% GO resulted in a membrane with an increased flux of 171 ± 3 Lm -2 h -1 with a MWCO of ~40 kDa. In addition, the GO incorporation efficiently inhibited the interaction between proteins and the membrane surface, thereby improving the fouling resistance ability by approximately 58 ± 3%. Also, the resulting membranes showed a significant improvement in mechanical and thermal properties., Competing Interests: The authors declare no competing financial interests.

The objective of the present work was to investigate the efficacy of indigenously developed polyacrylonitrile (PAN) based ultrafiltration (UF) membrane for chromium ions removal from potable water. The hydrolyzed PAN membranes effectively rejected chromium anions in the feed ranging from 250 ppb to 400 ppm and a rejection of ≥90% was achieved for pH ≥ 7 at low chromate concentration (≤25 ppm) in feed. The rejection mechanism of chromium ions was strongly dependent on Donnan exclusion principle, while size exclusion principle for UF did not play a major role on ions rejection. Feed pH played a vital role in changing porosity of membrane, which influenced the retention behavior of chromate ions. Cross-flow velocity, pressure did not play significant role for ions rejection at low feed concentration. However, at higher feed concentration (≥400 ppm), concentration polarization became important and it reduced the chromate rejection to 32% at low cross flow and high pressure. Donnan steric-partitioning pore and dielectric exclusion model (DSPM-DE) was applied to evaluate the chromate ions transport through PAN UF membrane as a function of flux by using optimized model parameters and the simulated data matched well with experimental results., Competing Interests: The authors declare no competing financial interests.

The increasing prevalence of antibiotic-resistant bacteria is creating a real challenge for health care systems worldwide, making the development of novel antibiotics a necessity. In addition to the development of new antibiotics, there is an urgent need for in-depth characterization of the mechanisms of bacterial resistance toward new drugs. Here, we used essential oils extracted in our laboratory from Piper cubeba against methicillin-resistant Staphylococcus aureus ATCC 43300, one of the most prominent antibiotic-resistant bacteria. Effects of the essential oils extracted from P cubeba on bacteria were mainly evaluated using 2 powerful microscopy techniques: atomic force microscopy and transmission electron microscopy. High-resolution atomic force microscopy images of the cells were obtained close to their native environment by immobilizing the cells on porous Polyether sulfone membranes, which were prepared in our laboratory with a wide range and distribution of pore sizes and depth. Inhibition zones (mm) and minimum inhibitory concentrations were determined. Two different concentrations of the oil were used to treat the cells: 50 μg/mL minimum inhibitory concentration and 25 μg/mL. The 50 μg/mL oil solution caused severe damage to the bacterial cells at microscopic levels while the 25 μg/mL solution showed no effects compared to the control. However, at nanoscopic levels, the 25 μg/mL oil solution caused significant changes in the cell wall, which could potentially impair bacterial activities. These results were also confirmed by transmission electron microscopy micrographs. Our results indicate that the extract has a good biological activity against methicillin- and oxacillin-resistant S aureus and that it acts on the cell wall and plasma (cytoplasmic) membrane., (Copyright © 2016 John Wiley & Sons, Ltd.)

With the evolution of nanoscience and nanotechnology, studies have been focused on manipulating nanoparticle properties through the control of their size, composition, and morphology. As nanomaterial research has progressed, the foremost focus has gradually shifted from synthesis, morphology control, and characterization of properties to the investigation of function and the utility of integrating these materials and chemical sciences with the physical, biological, and medical fields, which therefore necessitates the development of novel materials that are capable of performing multiple tasks and functions. The construction of multifunctional nanomaterials that integrate two or more functions into a single geometry has been achieved through the surface-coating technique, which created a new class of substances designated as core-shell nanoparticles. Core-shell materials have growing and expanding applications due to the multifunctionality that is achieved through the formation of multiple shells as well as the manipulation of core/shell materials. Moreover, core removal from core-shell-based structures offers excellent opportunities to construct multifunctional hollow core architectures that possess huge storage capacities, low densities, and tunable optical properties. Furthermore, the fabrication of nanomaterials that have the combined properties of a core-shell structure with that of a hollow one has resulted in the creation of a new and important class of substances, known as the rattle core-shell nanoparticles, or nanorattles. The design strategies of these new multifunctional nanostructures (core-shell, hollow core, and nanorattle) are discussed in the first part of this review. In the second part, different synthesis and fabrication approaches for multifunctional core-shell, hollow core-shell and rattle core-shell architectures are highlighted. Finally, in the last part of the article, the versatile and diverse applications of these nanoarchitectures in catalysis, energy storage, sensing, and biomedicine are presented.

In this work, Fe3O4@SiO2 nanoparticles were coated with mesoporous silica shell by S-N+I- pathway by using anionic surfactant (S-) and co-structure directing agent (N+). The role of co-structure directing agent (CSDA) is to assist the electrostatic interaction between negatively charged silica layers and the negatively charged surfactant molecules. Prior to the mesoporous shell formation step, magnetic cores were coated with a dense silica layer to prevent iron oxide cores from leaching into the mother system under any acidic circumstances. However, it was found that both dense and mesoporous coating parameters affect the textural properties of the produced mesoporous silica shell (i.e., surface area, pore volume and shell thickness). The synthesized Fe3O4@SiO2@m-SiO2 (MCMSS) nanoparticles have been characterized by low-angle X-ray diffraction, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, and magnetic properties. The synthesized particles had dense and mesoporous silica shells of 8-37 nm and 26-50 nm, respectively. Furthermore, MCMSS possessed surface area of ca. 259-621 m2·g-1, and pore volume of ca. 0.216-0.443 cc·g-1. MCMSS showed docetaxcel cancer drug storage capacity of 25-33 w/w% and possessed control release from their mesochannels which suggest them as proper nanocarriers for docetaxcel molecules.

Nanostructured materials are promising compounds that offer new opportunities as sensing platforms for the detection of biomolecules. Having micrometer-scale length and nanometer-scale diameters, nanomaterials can be manipulated with current nanofabrication methods, as well as self-assembly techniques, to fabricate nanoscale bio-sensing devices. Nanostructured materials possess extraordinary physical, mechanical, electrical, thermal and multifunctional properties. Such unique properties advocate their use as biomimetic membranes to immobilize and modify biomolecules on the surface of nanoparticles. Alignment, uniform dispersion, selective growth and diameter control are general parameters which play critical roles in the successful integration of nanostructures for the fabrication of bioelectronic sensing devices. In this review, we focus on different types and aspects of nanomaterials, including their synthesis, properties, conjugation with biomolecules and their application in the construction of immunosensing devices. Some key results from each cited article are summarized by relating the concept and mechanism behind each sensor, experimental conditions and the behavior of the sensor under different conditions, etc. The variety of nanomaterial-based bioelectronic devices exhibiting novel functions proves the unique properties of nanomaterials in such sensing devices, which will surely continue to expand in the future. Such nanomaterial based devices are expected to have a major impact in clinical immunodiagnostics, environmental monitoring, security surveillance and for ensuring food safety.