Search

Measurements of independent fission yield distributions in neutron-induced fission at high neutron energies are important for our fundamental understanding of the fission process, and are also relevant for reactor physics applications. So far, measurements of independent fission yields in proton-induced fission have been performed at the IGISOL facility at the University of Jyväskylä, using the Penning trap as a high resolving-power mass-filter. In order to also facilitate measurements of neutron-induced fission, a dedicated ion guide and a proton-to-neutron converter was developed. However, the first measurement indicates that fewer fission products than expected reach the Penning trap. To explore potential reasons and possible improvements, a simulation model was also developed and benchmarked. The benchmark showed that the model is able to reproduce the performance of the ion guide remarkably well and that the main reason for the low yield of fission products is the low collection efficiency of the ion guide. Based on the benchmark, a new ion guide is being designed. In the new design, the positions of the uranium targets and volume of the ion guide have been changed to increase the collection of fission products. This results in a five-fold increase of the yield. However, the collection efficiency of the new ion guide still needs to be improved in order to achieve intensities of the extracted fission products that are large enough to allow for reasonable measurement times. Because the volume of the ion guide is increased significantly, the extraction time of the ions is expected to be longer than that from the previous ion guide. Therefore, an electric field guidance system that consists of a combination of a stationary electric field and an RF-carpet is considered to be deployed. The stationary field, produced from a set of DC-ring electrodes, accelerates the ions towards the RF-carpet at end plate of the ion guide. The RF-carpet consists of a time-dependent fi

The VElocity foR Direct particle Identification spectrometer (VERDI) is a 2E-2v fission spectrometer that allows the measurement of the total mass distribution of secondary fission fragments with a resolving power of 1-2 u. It consists of two time-of-flight (ToF) arms, with one Micro Channel Plate (MCP) detector and up to 32 Silicon PIPS (Passive Implanted Planar Silicon) detectors per arm. The MCPs provide the start timing signals and the PIPS detectors provide both the energy and the stopping ToF signals. In real conditions, the PIPS signals are affected by the formation of plasma from the interaction between the heavy ions and the detector material. The plasma contributes to a reduction in signal amplitude, resulting in a Pulse Height Defect (PHD), and introduces a signal delay, known as Plasma Delay Time (PDT). An experiment to characterize the PDT and PHD was performed at the LOHENGRIN recoil separator of the Institut Laue Langevin (ILL). Characteristic fission fragments from the 239Pu(n,f) reaction were separated based on their A/Q and E/Q ratios, allowing the measurement of a wide range of energies from 21 to 110 MeV and masses between 80 and 149 u. Six PIPS detectors were characterized to study their individual responses to the PDT and PHD effects. The signals were recorded in a digital acquisition system to completely exploit the offline analysis capabilities. Achieved combined timing and energy resolutions for fission fragments varied between 72(2) ps and 100(4) ps and 1.4% - 2% (FWHM), respectively. Preliminary PHD and PDT data are presented from the masses A=85, 95, 130 and 143. The PHD trends are strongly correlated with both the ion energy and mass. The PDT, on the other hand, shows a strong variation as a function of the ion kinetic energy but a smaller dependence on the ion mass.

The TALYS nuclear reaction code's Hauser-Feshbach statistical decay model has been adapted in order to calculate prompt fission neutron and ?-ray observables by iterating over deexciting fission fragments. Several fission fragment generators such as GEF, HF3D, and SPY were employed to provide TALYS with databases. These databases contain standardized tables with fission fragment yields, mean excitation energies and their widths, and aver-age total kinetic energy, as a function of charge and mass number of primary fission fragments. The resulting calcula-tions, including prompt particle multiplicities, spectra, aver-age energies, and independent fission product yields, were compared with experimental and evaluated data. This work first outlines the new methodology implemented in TALYS and examines the effects of three important parameters on the final evaporation data. Furthermore, the neutron-induced fission of U-235 is investigated in detail as a function of inci-dent energy. The results from TALYS, with input from GEF and (HFD)-D-3, were compared with available experimental data and the results of the stand-alone GEF code. The proposed methodology contributes to an improved capability to model the fission process.

In a measurement of isomeric yield-ratios in fission, the Phase-Imaging Ion-Cyclotron-Resonance technique, which projects the radial motions of ions in the Penning trap (JYFLTRAP) onto a position-sensitive micro-channel plate detector, has been applied. To obtain the yield ratio, that is the relative population of two states of an isomer pair, a novel analysis procedure has been developed to determine the number of detected ions in each state, as well as corrections for the detector efficiency and decay losses. In order to determine the population of the states in cases where their mass difference is too small to reach full separation, a Bayesian Gaussian Mixture model was implemented. The position-dependent efficiency of the micro-channel plate detector was calibrated by mapping it with 133Cs+ ions, and a Gaussian Process was trained with the position data to construct an efficiency function that could be used to correct the recorded distributions. The obtained numbers of counts of excited and ground-state ions were used to derive the isomeric yield ratio, taking into account decay losses as well as feeding from precursors.

Background: Isomeric yield ratios are an important observable in nuclear fission as they can guide model development by providing insight into the angular momentum generation. Furthermore, isomeric yield ratios are important in applications for nuclear energy, as well as in the study of the r-process in stellar nucleosynthesis, and in the antineutrino mixing angle from reactor spectra. In nuclear data evaluations, the Madland-England model is commonly used to estimate isomeric yield ratios that have not been measured. Purpose: To measure isomeric yield ratios in 25-MeV proton-induced fission of 238U, and to compare the result with the values obtained from the Madland-England model and the fission model code GEF. Furthermore, to evaluate whether the predictions of GEF can be improved by coupling it to the nuclear reaction code TALYS. Methods: Isomeric yield ratios in 25-MeV proton-induced fission of 238U have been measured at the Ion GuideIsotope Separate On-Line facility. The excited state and the ground state were separated by mass using the Phase-Imaging Ion-Cyclotron-Resonance technique in the double Penning trap JYFLTRAP. The number of counts of each state was extracted from the phase-images using a Bayesian Gaussian Mixture model and, after corrections fordetector efficiency and decay, the isomeric yield ratios were derived. The experimental values have been compared with the calculated results from the Madland-England model and the GEF code. Furthermore, GEF has been combined with the nuclear reaction code TALYS, in order to take advantage of the latter codes’ implementation of the Hauser-Feshbach formalism, and the results have been compared with the experimental values. Results: From the measurements, 19 new isomeric yield ratios in 25-MeV proton-induced fission of 238U are reported and are, together with another 12 isomeric yield ratios (IYRs) from a previous campaign, compared with the model calculations. It is shown that, though the models manage to captu

The covariance committee of CSEWG (Cross Section Evaluation Working Group) established templates of expected measurement uncertainties for neutron-induced total, (n,gamma), neutron-induced charged-particle, and (n,xn) reaction cross sections as well as prompt fission neutron spectra, average prompt and total fission neutron multiplicities, and fission yields. Templates provide a list of what uncertainty sources are expected for each measurement type and observable, and suggest typical ranges of these uncertainties and correlations based on a survey of experimental data, associated literature, and feedback from experimenters. Information needed to faithfully include the experimental data in the nuclear-data evaluation process is also provided. These templates could assist (a) experimenters and EXFOR compilers in delivering more complete uncertainties and measurement information relevant for evaluations of new experimental data, and (b) evaluators in achieving a more comprehensive uncertainty quantification for evaluation purposes. This effort might ultimately lead to more realistic evaluated covariances for nuclear-data applications. In this topical issue, we cover the templates coming out of this CSEWG effort-typically, one observable per paper. This paper here prefaces this topical issue by introducing the concept and mathematical framework of templates, discussing potential use cases, and giving an example of how they can be applied (estimating missing experimental uncertainties of 235U(n,f) average prompt fission neutron multiplicities), and their impact on nuclear-data evaluations.

The COVID-19 induced restrictions have prevented reactor physics students from attending in-person reactor physics exercises which are a vital part of their education. Jozef Stefan Institute has organized remote exercises with the help of off-the-shelf technology, including multiple videoconferencing setups, remote desktop software, portable cameras, a dome camera, shared spreadsheets, and a common whiteboard. The students were encouraged to actively participate in the exercises by giving instructions to the reactor operator, asking and answering questions, logging data, operating digital acquisition systems, and performing analysis during the exercise. The first remote exercises were organized as a five-day course of experimental reactor physics for students from Uppsala University. The feedback was collected after the course using an anonymous online form and was generally positive but has revealed some problems with sound quality which were resolved later. The Jozef Stefan Institute can also organize a remote course during a full lockdown when the reactor is not able to operate using the in-house developed Research Reactor Simulator based on a point kinetics approximation and a simple thermohydraulic module.

The COVID-19 induced restrictions have prevented reactor physics students from attending in-person reactor physics exercises which are a vital part of their education. Jo.zef Stefan Institute has organized remote exercises with the help of off-the-shelf technology, including multiple videoconferencing setups, remote desktop software, portable cameras, a dome camera, shared spreadsheets, and a common whiteboard. The students were encouraged to actively participate in the exercises by giving instructions to the reactor operator, asking and answering questions, logging data, operating digital acquisition systems, and performing analysis during the exercise. The first remote exercises were organized as a five-day course of experimental reactor physics for students from Uppsala University. The feedback was collected after the course using an anonymous online form. The aspects being evaluated included the technical content, quality of material, performance of the individual lecturers and the quality of the remote session. In general, the response was overwhelmingly positive, with most questions with a rating scale answered with "excellent".

The generation of angular momentum in the fission process is still an open question. To shed light on this topic, we started a series of measurements at the IGISOL-JYFLTRAP facility in Finland. Highprecision measurements of isomeric yield ratios (IYR) are performed with a Penning trap, partly with the aim to extract average root-mean-square (rms) quantities of fragment spin distributions. The newly installed Phase-Imaging Ion-Cyclotron Resonance (PI-ICR) technique allows the separation of masses down to tens of keV, which is suffcient to disentangle many isomers. In this paper, we first summarize the previous measurements on the neutron and proton-induced fission of uranium and thorium, e.g. the odd cadmium and indium isotopes (119 ≤ A ≤ 127). The measurements revealed systematic trends as function of mass number, which stimulated further exploration. A recent measurement was performed at IGISIOL and several new IYR data will soon be published, for the first time. Secondly, we employ the TALYS nuclear-reaction code to model one of the newly measured isomer yields. Detailed GEF and TALYS calculations are discussed for the fragment angular momentum distribution in 134I.

Prompt gamma-ray spectra emitted in fast-neutron induced fission of 239 Pu have been recently measured by using the LICORNE directional neutron source at En = 1.8 MeV. The results are used in parallel with the measurements of fast-neutron induced fission of 238 U and spontaneous fission of 252Cf to assess the potential of such reactions and observables, in contributing to the understanding of fission. The gamma-ray spectra were measured and analyzed under similar conditions, allowing a consistent and robust comparison between the three systems. They are further compared to Monte-Carlo simulations based on two widely-used semi-empirical codes, FREYA and GEF. Differences in the low and high energy portions of the spectrum are interpreted based on simple arguments involving nuclear structure and evaporation effects. The significance and potential of experimental campaigns of this kind, as well as current limitations, are highlighted, together with straightforward but mandatory extensions.

Fission fragments exhibit large angular momenta J, which constitutes a challenge for fission models to fully explain. Systematic measurements of isomeric yield ratios (IYR) are needed for basic nuclear reaction physics and nuclear applications, especially as a function of mass number and excitation energy. One goal is to improve the current understanding of the angular momentum generation and sharing in the fission process. To do so, one needs to improve the modeling of nuclear de-excitation. In this work, we have used the TALYS nuclear-reaction code to relax excited fission fragments and to extract root-mean-square (rms) values of initial spin distributions, after comparison with experimentally determined IYRs. The method was assessed by a comparative study on Cf-252(sf) and (235)(nth,f). The results show a consistent performance of TALYS, both in comparison to reported literature values and to other fission codes. A few discrepant Jrms values were also found. The discrepant literature values could need a second consideration as they could possibly be caused by outdated models. Our TALYS method will be refined to better comply with contemporary sophisticated models and to reexamine older deduced values in literature.

For the production of exotic nuclei at the IGISOL facility, an ion guide for neutron-induced fission has been developed and tested in experiments. Fission fragments are produced inside the ion guide and collected using a helium buffer gas. Meanwhile, a GEANT4 model has been developed to simulate the transportation and stopping of the charged fission products. In a recent measurement of neutron-induced fission yields, implantation foils were located at different positions in the ion guide. The gamma spectra from these foils and the fission targets are compared to the results from the GEANT4 simulation. In order to allow fission yield measurements in the low yield regions, towards the tails and in the symmetric part of the mass distribution, the stopping and extraction efficiency of the ion guide has to be significantly improved. This objective can be achieved by increasing the size while introducing electric field guidance using a combination of static electrodes and an RF-carpet. To this end, the GEANT4 model is used to optimise the design of such an ion guide.

The generation of angular momentum in fission is difficult to model, in particular at higher excitation energies where data are scarce. Isomeric yield ratios (IYR) play an important role in deducing angular momentum properties of fission fragments (FF), albeit this requires some assumptions and simplifications. To estimate FF angular momentum, fission codes can be used to calculate IYRs and compare them to experimental data. Such measurements have systematically been performed at the IGISOL facility using novel experimental techniques. In conjunction, a new method has been developed to infer the angular momentum of the primary FF using the nuclear reaction code TALYS. In this work, we evaluate this new method by comparing our TALYS calculations with values found in the literature and with results from the GEF fission code, for a few well-studied reactions. The overall results show a consistent performance of TALYS and GEF, as well as of many reported literature values. However, some deviations were found, possibly pinpointing the need to re-examine some of the reported literature values. A sensitivity analysis was also performed, in which the role of excitation energy, neutron emission, discrete level structure and level density models were studied. Finally, the role of multiple chance fission, of relevance for the reactions studied at IGISOL, is discussed. Some literature data for this reaction were also re-analyzed using TALYS, revealing significant differences.

Isomeric yield ratios for the odd-A isotopes of Cd119-127 and In119-127 from 25-MeV proton-induced fission on natural uranium have been measured at the JYFLTRAP double Penning trap, by employing the phase-imaging ion-cyclotron-resonance technique. With the significantly improved mass resolution of this novel method isomeric states separated by 140 keV from the ground state, and with half-lives of the order of 500 ms, could be resolved. This opens the door for obtaining new information on low-lying isomers, which are important for nuclear structure, fission, and astrophysics. In the present work the experimental isomeric yield ratios are used for the estimation of the root-mean-square angular momentum J(rms) of the primary fragments. The results show a dependency on the number of unpaired protons and neutrons, where the odd-Z In isotopes carry larger angular momenta. The deduced values of J(rms) display a linear relationship when compared with the electric quadrupole moments of the fission products.

This work aims at measuring prompt-fission neutrons at different excitation energies of the nucleus. Two independent techniques, the 2E-2v and the 2E techniques, are used to map the characteristics of the mass-dependent prompt fission neutron multiplicity, 7(A), when the excitation energy is increased. The VERDI 2E-2v spectrometer is being developed at JRC-GEEL. The Fission Fragment (FF) energies are measured using two arrays of 16 silicon (Si) detectors each. The FFs velocities are obtained by time-of-flight, measured between micro-channel plates (MCP) and Si detectors. With MCPs placed on both sides of the fission source, VERDI allows for independent timing measurements for both fragments. Cf-252(sf) was measured and the present results revealed particular features of the 2E-2v technique. Dedicated simulations were also performed using the GEF code to study important aspects of the 2E-2v technique. Our simulations show that prompt neutron emission has a non-negligible impact on the deduced fragment data and affects also the shape of 17(A). Geometrical constraints lead to a total-kinetic energy-dependent detection efficiency. The 2E technique utilizes an ionization chamber together with two liquid scintillator detectors. Two measurements have been performed, one of Cf-252(sf) and another one of thermal-neutron induced fission in U-235(n,f). Results from Cf-252(sf) are reported here.

Prompt fission gamma-ray spectra (PFGS) have been measured for the Pu-239(n,f) reaction using fast neutrons at E-n =1.81 MeV produced by the LICORNE directional neutron source. The setup makes use of LaBr3 scintillation detectors and PARIS phoswich detectors to measure the emitted prompt fission gamma rays (PFG). The mean multiplicity, average total energy release per fission and average energy of photons are extracted from the unfolded PFGS. These new measurements provide complementary information to other recent work on thermal neutron induced fission of Pu-239 and spontaneous fission of Cf-252.

Data on fission yields and isomeric yield ratios (IYR) are tools to study the fission process, in particular the generation of angular momentum. We use the IGISOL facility with the Penning trap JYFLTRAP in Jyvaskyla, Finland, for such measurements on Th-232 and U-nat targets. Previously published fission yield data from IGISOL concern the Th-232(p,f) and U-238(p,f) reactions at 25 and 50 MeV. Recently, a neutron source, using the Be(p,n) reaction, has been developed, installed and tested. We summarize the results for (p,f) focusing on the first measurement of IYR by direct ion counting. We also present first results for IYR and relative yields for Sn and Sb isotopes in the 128-133 mass range from U-nat(n,f) based on gamma-spectrometry. We find a staggering behaviour in the cumulative yields for Sn and a shift in the independent fission yields for Sb as compared to current evaluations. Plans for the future experimental program on fission yields and IYR measurements are discussed.

The investigation of the dynamics of the nuclear fission process has been a standing research topic at the JRC-Geel during the past decades. Recently the focus was put on the de-excitation of fission fragments through the emission of prompt neutrons and gamma-rays. To this end new detector systems were developed at JRC-Geel, e.g. a position sensitive ionization chamber used in conjunction with the neutron scintillator array SCINTIA. The array has been tested using the spontaneous fission of Cf-252. The goal is to study correlations of fission fragments with prompt neutron emission in the resolved resonance region. No strong fluctuations of the average prompt neutron multiplicity for the strongest resonances in U-235 were observed. From the present data the mass-dependent neutron multiplicity, v(A), was generated. The v(A) distribution shows a more pronounced dip around the doubly magic mass A = 132 and at very low masses around A similar to 80 compared to the literature. In addition, a steeper slope for v(TKE) is observed. Cross checking with fragment data clearly shows a narrower mass and total kinetic energy (TKE) distribution. The 2E-2v spectrometer VERDI (VElocity foR Direct mass Identification) became operational. For Cf-252(sf) superior mass resolution is observed compared to a twin Frisch-grid ionization chamber. For post-neutron mass distributions still some issues need to be solved and v(A), being the difference of pre- and post-neutron mass distributions, is still deviating from literature data. Eventually, VERDI will provide a complementary measurement technique to assess v(A) and v(TKE). In addition, an experimental campaign to measure v(A) as a function of incident neutron energy for different actinides has been started. First tests show promising results.

We report the first experimental determination of independent isomeric yield ratios using direct ion counting with a Penning trap, which offered such a high resolution in mass that isomeric states could be separated. The measurements were performed at the Ion Guide Isotope Separator On-Line (IGISOL) facility at the University of Jyvaskyla. The isomer production ratios of Ge-81, Y-96,Y-97 Sn-128(,1)30, and Sb-129 in the 25-MeV proton-induced fission of U-na(t) and Th-232 were studied. Three isomeric pairs (Ge-81, Y-96, and Sb-129) were measured for the first time for the U-na(t)(p, f) reaction, while all the reported yield ratios for the Th-232(p, f) reaction were determined for the first time. The comparison of the experimentally determined isomeric yield ratios with data available in the literature shows a reasonable agreement, except for the case of Sn-130 for unspecified reasons. The obtained results were also compared with the GEF model, where good agreement can be noticed in most cases for both reactions. Serious discrepancies can only be observed for the cases of Y-96(,)97 for both reactions. Moreover, based on the isomeric yield ratios, the root-mean-square angular momenta (J(r)(ms)) of the fission fragments after scission were estimated using the TALYS code. The experimentally determined isomeric yield ratios, and consequently the deduced J(rms), for Sn-130 are significantly lower compared to Sn-128 for both fissioning systems. This can be attributed to the more spherical shape of the fragments that contribute to the formation of Sn-130, due to their proximity to the N = 82 shell closure. The values of J(rms) for Sb-129 are higher than Sn-128 for both reactions, despite the same neutron number of both nuclides (N = 78), indicating the odd-Z effect where fission fragments with odd-Z number tend to bear larger angular momentum than even-Z fragments. The isomer production ratio for the isotopes of Sn is more enhanced in the U-na(t)(p, f) reaction than in Th-232

The first systematic measurement of neutron-induced fission yields has been performed at the upgraded IGISOL-4 facility at the University of Jyvaskyla, Finland. The fission products from high-energy neutron-induced fission of U-nat were stopped in a gas cell filled with helium buffer gas, and were online separated with a dipole magnet. The isobars, with masses in the range A = 128-133, were transported to a tape-implantation station and identified using gamma-spectroscopy. We report here the relative cumulative isotopic yields of tin (Z = 50) and the relative independent isotopic yields of antimony (Z = 51). Isomeric yield ratios were also obtained for five nuclides. The yields of tin show a staggered behaviour around A = 131, not observed in the ENDF/B-VII. 1 evaluation. The yields of antimony also contradict the trend from the evaluation, but are in agreement with a calculation performed using the GEF model that shows the yield increasing with mass in the range A = 128-133.

A white neutron source based on the Be(p,nx) reaction for fission studies at the IGISOLJYFLTRAP facility has been designed and tested. 30 MeV protons impinge on a 5mm thick water-cooled beryllium disc. The source was designed to produce at least 1012 fast neutrons/s on a secondary fission target, in order to reach competitive production rates of fission products far from the valley of stability. The Monte Carlo codes MCNPX and FLUKA were used in the design phase to simulate the neutron energy spectra. Two experiments to characterise the neutron field were performed: the first was carried out at The Svedberg Laboratory in Uppsala (SE), using an Extended-Range Bonner Sphere Spectrometer and a liquid scintillator which used the time-of-flight (TOF) method to determine the energy of the neutrons; the second employed Thin-Film Breakdown Counters for the measurement of the TOF, and activation foils, at the IGISOL facility in Jyväskylä (FI). Design considerations and the results of the two characterisation measurements are presented, providing benchmarks for the simulations.

The nuclear de-excitation process of fission fragments (FF) provides fundamental information for the understanding of nuclear fission and nuclear structure in neutron-rich isotopes. The variation of the prompt-neutron multiplicity, ν(A), as a function of the incident neutron energy (En) is one of many open questions. It leads to significantly different treatments in various fission models and implies that experimental data are analyzed based on contradicting assumptions. One critical question is whether the additional excitation energy (Eexc) is manifested through an increase of ν(A) for all fragments or for the heavy ones only. A systematic investigation of ν(A) as a function of En has been initiated. Correlations between prompt-fission neutrons and fission fragments are obtained by using liquid scintillators in conjunction with a Frisch-grid ionization chamber. The proof-of-principle has been achieved on the reaction 235U(nth,f) at the Van De Graff (VdG) accelerator of the JRC-Geel using a fully digital data acquisition system. Neutrons from 252Cf(sf) were measured separately to quantify the neutron-scattering component due to surrounding shielding material and to determine the intrinsic detector efficiency. Prelimenary results on ν(A) and spectrum in correlation with FF properties are presented.

VERDI (VElocity foR Direct particle Identification) is a fission-fragment spectrometer recently put into operation at JRC-Geel. It allows measuring the kinetic energy and velocity of both fission fragments simultaneously. The velocity provides information about the pre-neutron mass of each fission fragment when isotropic prompt-neutron emission from the fragments is assumed. The kinetic energy, in combination with the velocity, provides the post-neutron mass. From the difference between pre- and post-neutron masses, the number of neutrons emitted by each fragment can be determined. Multiplicity as a function of fragment mass and total kinetic energy is one important ingredient, essential for understanding the sharing of excitation energy between fission fragments at scission, and may be used to benchmark nuclear de-excitation models. The VERDI spectrometer design is a compromise between geometrical efficiency and mass resolution. The spectrometer consists of an electron detector located close to the target and two arrays of silicon detectors, each located 50 cm away from the target. In the present configuration pre-neutron and post-neutron mass distributions are in good agreement with reference data were obtained. Our latest measurements performed with spontaneously fissioning 252Cf is presented along with the developed calibration procedure to obtain pulse height defect and plasma delay time corrections.

The Li-6(n,alpha)t reaction cross-section is an established standard due to its relatively high crosssection as well as its high Q-value. However, it is only considered a neutron standard up to 1 MeV, because in the neutron energy region 1-3 MeV there exist discrepancies of several per cents between recent measurements [1,2] and evaluated data files [3]. It has been speculated [4] that neglecting of the particle leaking effect might be part of the explanation why there is a disagreement in this region. Based on R-matrix calculations, in the region around 2 MeV, one also expects three excitation levels of Li-7 to significantly influence the cross section [5]. In order to resolve these discrepancies, we perform measurements at the GELINA facility at JRC-Geel with two Frisch-gridded ionisation chambers. The Li-6(n,alpha)t cross section is measured relative to the U-235(n,f) standard. In order to solve previous encountered problems [6], the setup has been modified and moved to a new flight path station. In this proceeding we show that several problems have been eliminated and discuss possible solutions to newly arisen problems, due to the changed experimental conditions. Preliminary results from new data taken during 2016 with the updated setup are presented., Updated setup from result 2016, DOI: 10.1051/epjconf/201612208006.