Search

A monolithic silicon pixel ASIC prototype, produced in 2024 as part of the Horizon 2020 MONOLITH ERC Advanced project, was tested with a 120 GeV/c pion beam. The ASIC features a matrix of hexagonal pixels with a 100 \mu m pitch, read by low-noise, high-speed front-end electronics built using 130 nm SiGe BiCMOS technology. It includes the PicoAD sensor, which employs a continuous, deep PN junction to generate avalanche gain. Data were taken across power densities from 0.05 to 2.6 W/cm2 and sensor bias voltages from 90 to 180 V. At the highest bias voltage, corresponding to an electron gain of 50, and maximum power density, an efficiency of (99.99 \pm 0.01)% was achieved. The time resolution at this working point was (24.3 \pm 0.2) ps before time-walk correction, improving to (12.1 \pm 0.3) ps after correction.

This letter presents the measurement of the energy-dependent neutrino-nucleon cross section in tungsten and the differential flux of muon neutrinos and anti-neutrinos. The analysis is performed using proton-proton collision data at a center-of-mass energy of $13.6 \, {\rm TeV}$ and corresponding to an integrated luminosity of $(65.6 \pm 1.4) \, \mathrm{fb^{-1}}$. Using the active electronic components of the FASER detector, $338.1 \pm 21.0$ charged current muon neutrino interaction events are identified, with backgrounds from other processes subtracted. We unfold the neutrino events into a fiducial volume corresponding to the sensitive regions of the FASER detector and interpret the results in two ways: We use the expected neutrino flux to measure the cross section, and we use the predicted cross section to measure the neutrino flux. Both results are presented in six bins of neutrino energy, achieving the first differential measurement in the TeV range. The observed distributions align with Standard Model predictions. Using this differential data, we extract the contributions of neutrinos from pion and kaon decays.

The design of fast reactors burning MOX fuels requires accurate capture and fission cross sections. For the particular case of neutron capture on 242Pu, the NEA recommends that an accuracy of 8-12% should be achieved in the fast energy region (2 keV-500 keV) compared to their estimation of 35% for the current uncertainty. Integral irradiation experiments suggest that the evaluated cross section of the JEFF-3.1 library overestimates the 242Pu(n,{\gamma}) cross section by 14% in the range between 1 keV and 1 MeV. In addition, the last measurement at LANSCE reported a systematic reduction of 20-30% in the 1-40 keV range relative to the evaluated libraries and previous data sets. In the present work this cross section has been determined up to 600 keV in order to solve the mentioned discrepancies. A 242Pu target of 95(4) mg enriched to 99.959% was irradiated at the n TOF-EAR1 facility at CERN. The capture cross section of 242Pu has been obtained between 1 and 600 keV with a systematic uncertainty (dominated by background subtraction) between 8 and 12%, reducing the current uncertainties of 35% and achieving the accuracy requested by the NEA in a large energy range. The shape of the cross section has been analyzed in terms of average resonance parameters using the FITACS code as implemented in SAMMY, yielding results compatible with our recent analysis of the resolved resonance region.The results are in good agreement with the data of Wisshak and K\"appeler and on average 10-14% below JEFF-3.2 from 1 to 250 keV, which helps to achieve consistency between integral experiments and cross section data. At higher energies our results show a reasonable agreement within uncertainties with both ENDF/B-VII.1 and JEFF-3.2. Our results indicate that the last experiment from DANCE underestimates the capture cross section of 242Pu by as much as 40% above a few keV., Comment: 20 pages, 19 figures, submitted to Phys. Rev. C

The first FASER search for a light, long-lived particle decaying into a pair of photons is reported. The search uses LHC proton-proton collision data at $\sqrt{s}=13.6~\text{TeV}$ collected in 2022 and 2023, corresponding to an integrated luminosity of $57.7\text{fb}^{-1}$. A model with axion-like particles (ALPs) dominantly coupled to weak gauge bosons is the primary target. Signal events are characterised by high-energy deposits in the electromagnetic calorimeter and no signal in the veto scintillators. One event is observed, compared to a background expectation of $0.44 \pm 0.39$ events, which is entirely dominated by neutrino interactions. World-leading constraints on ALPs are obtained for masses up to $300~\text{MeV}$ and couplings to the Standard Model W gauge boson, $g_{aWW}$, around $10^{-4}$ GeV$^{-1}$, testing a previously unexplored region of parameter space. Other new particle models that lead to the same experimental signature, including ALPs coupled to gluons or photons, U(1)$_B$ gauge bosons, up-philic scalars, and a Type-I two-Higgs doublet model, are also considered for interpretation, and new constraints on previously viable parameter space are presented in this paper., Comment: 37 pages, 22 figures

The $\beta$ decay of one-neutron halo nucleus $^{11}$Be was investigated using the Warsaw Optical Time Projection Chamber (OTPC) detector to measure $\beta$-delayed charged particles. The results of two experiments are reported. In the first one, carried out in LNS Catania, the absolute branching ratio for $\beta$-delayed $\alpha$ emission was measured by counting incoming $^{11}$Be ions stopped in the detector and the observed decays with the emission of $\alpha$ particle. The result of 3.27(46)\% is in good agreement with the literature value. In the second experiment, performed at the HIE-ISOLDE facility at CERN, bunches containing several hundreds of $^{11}$Be ions were implanted into the OTPC detector followed by the detection of decays with the emission of charged particles. The energy spectrum of $\beta$-delayed $\alpha$ particles was determined in the full energy range. It was analysed in the R-matrix framework and was found to be consistent with the literature. The best description of the spectrum was obtained assuming that the two $3/2^+$ and one $1/2^+$ states in $^{11}$B are involved in the transition. The search for $\beta$-delayed emission of protons was undertaken. Only the upper limit for the branching ratio for this process of $(2.2 \pm 0.6_{\rm stat} \pm 0.6_{\rm sys}) \times 10^{-6}$ could be determined. This value is in conflict with the result published in [Ayyad et al. Phys. Rev. Lett. 123, 082501 (2019)] but does agree with the limit reported in [Riisager et al., Eur. Phys. J. A (2020) 56:100], Comment: 16 pages, 18 figures, submitted to Phys. Rev. C

Samples of the monolithic silicon pixel ASIC prototype produced in 2022 within the framework of the Horizon 2020 MONOLITH ERC Advanced project were irradiated with 70 MeV protons up to a fluence of 1 x 1016 neq/cm2, and then tested using a beam of 120 GeV/c pions. The ASIC contains a matrix of 100 \mu m pitch hexagonal pixels, readout out by low noise and very fast frontend electronics produced in a 130 nm SiGe BiCMOS technology process. The dependence on the proton fluence of the efficiency and the time resolution of this prototype was measured with the frontend electronics operated at a power density between 0.13 and 0.9 W/cm2. The testbeam data show that the detection efficiency of 99.96% measured at sensor bias voltage of 200 V before irradiation becomes 96.2% after a fluence of 1 x 1016 neq/cm2. An increase of the sensor bias voltage to 300 V provides an efficiency to 99.7% at that proton fluence. The timing resolution of 20 ps measured before irradiation rises for a proton fluence of 1 x 1016 neq/cm2 to 53 and 45 ps at HV = 200 and 300 V, respectively.

This paper presents the first results of the study of high-energy electron and muon neutrino charged-current interactions in the FASER$\nu$ emulsion/tungsten detector of the FASER experiment at the LHC. A subset of the FASER$\nu$ volume, which corresponds to a target mass of 128.6~kg, was exposed to neutrinos from the LHC $pp$ collisions with a centre-of-mass energy of 13.6~TeV and an integrated luminosity of 9.5 fb$^{-1}$. Applying stringent selections requiring electrons with reconstructed energy above 200~GeV, four electron neutrino interaction candidate events are observed with an expected background of $0.025^{+0.015}_{-0.010}$, leading to a statistical significance of 5.2$\sigma$. This is the first direct observation of electron neutrino interactions at a particle collider. Eight muon neutrino interaction candidate events are also detected, with an expected background of $0.22^{+0.09}_{-0.07}$, leading to a statistical significance of 5.7$\sigma$. The signal events include neutrinos with energies in the TeV range, the highest-energy electron and muon neutrinos ever detected from an artificial source. The energy-independent part of the interaction cross section per nucleon is measured over an energy range of 560--1740 GeV (520--1760 GeV) for $\nu_e$ ($\nu_{\mu}$) to be $(1.2_{-0.7}^{+0.8}) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$ ($(0.5\pm0.2) \times 10^{-38}~\mathrm{cm}^{2}\,\mathrm{GeV}^{-1}$), consistent with Standard Model predictions. These are the first measurements of neutrino interaction cross sections in those energy ranges.

The Forward Search Experiment (FASER) at CERN's Large Hadron Collider (LHC) has recently directly detected the first collider neutrinos. Neutrinos play an important role in all FASER analyses, either as signal or background, and it is therefore essential to understand the neutrino event rates. In this study, we update previous simulations and present prescriptions for theoretical predictions of neutrino fluxes and cross sections, together with their associated uncertainties. With these results, we discuss the potential for possible measurements that could be carried out in the coming years with the FASER neutrino data to be collected in LHC Run 3 and Run 4., Comment: 19 pages, 10 figures

The time resolution of the second monolithic silicon pixel prototype produced for the MONOLITH H2020 ERC Advanced project was studied using a femtosecond laser. The ASIC contains a matrix of hexagonal pixels with 100 {\mu}m pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Silicon wafers with 50 {\mu}m thick epilayer with a resistivity of 350 {\Omega}cm were used to produce a fully depleted sensor. At the highest frontend power density tested of 2.7 W/cm2, the time resolution with the femtosecond laser pulses was found to be 45 ps for signals generated by 1200 electrons, and 3 ps in the case of 11k electrons, which corresponds approximately to 0.4 and 3.5 times the most probable value of the charge generated by a minimum-ionizing particle. The results were compared with testbeam data taken with the same prototype to evaluate the time jitter produced by the fluctuations of the charge collection., Comment: Submitted to JINST

The cluster structure of the neutron-rich isotope $^{10}$Be has been probed via the $(p,p\alpha)$ reaction at 150 MeV/nucleon in inverse kinematics and in quasifree conditions. The populated states of $^{6}$He residues were investigated through missing mass spectroscopy. The triple differential cross-section for the ground-state transition was extracted for quasifree angle pairs ($\theta_{p}$, $\theta_{\alpha}$) and compared to distorted-wave impulse approximation reaction calculations performed in a microscopic framework using successively the Tohsaki-Horiuchi-Schuck-R\"opke product wave-function and the wave-function deduced from Antisymmetrized Molecular Dynamics calculations. The remarkable agreement between calculated and measured cross-sections in both shape and magnitude validates the molecular structure description of the $^{10}$Be ground-state, configured as an $\alpha$-$\alpha$ core with two valence neutrons occupying $\pi$-type molecular orbitals., Comment: 7 pages, 3 figures, 1 tables

A monolithic silicon pixel prototype produced for the MONOLITH ERC Advanced project was irradiated with 70 MeV protons up to a fluence of 1 x 10^16 1 MeV n_eq/cm^2. The ASIC contains a matrix of hexagonal pixels with 100 {\mu}m pitch, readout by low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 {\mu}m thick epilayer with a resistivity of 350 {\Omega}cm were used to produce a fully depleted sensor. Laboratory tests conducted with a 90Sr source show that the detector works satisfactorily after irradiation. The signal-to-noise ratio is not seen to change up to fluence of 6 x 10^14 n_eq /cm^2 . The signal time jitter was estimated as the ratio between the voltage noise and the signal slope at threshold. At -35 {^\circ}C, sensor bias voltage of 200 V and frontend power consumption of 0.9 W/cm^2, the time jitter of the most-probable signal amplitude was estimated to be 21 ps for proton fluence up to 6 x 10 n_eq/cm^2 and 57 ps at 1 x 10^16 n_eq/cm^2 . Increasing the sensor bias to 250 V and the analog voltage of the preamplifier from 1.8 to 2.0 V provides a time jitter of 40 ps at 1 x 10^16 n_eq/cm^2., Comment: Submitted to JINST

A second monolithic silicon pixel prototype was produced for the MONOLITH project. The ASIC contains a matrix of hexagonal pixels with 100 {\mu}m pitch, readout by a low-noise and very fast SiGe HBT frontend electronics. Wafers with 50 {\mu}m thick epilayer of 350 {\Omega}cm resistivity were used to produce a fully depleted sensor. Laboratory and testbeam measurements of the analog channels present in the pixel matrix show that the sensor has a 130 V wide bias-voltage operation plateau at which the efficiency is 99.8%. Although this prototype does not include an internal gain layer, the design optimised for timing of the sensor and the front-end electronics provides a time resolutions of 20 ps., Comment: 11 pages, 11 figures

The proof-of-concept prototype of the Picosecond Avalanche Detector, a multi-PN junction monolithic silicon detector with continuous gain layer deep in the sensor depleted region, was tested with a beam of 180 GeV pions at the CERN SPS. The prototype features low noise and fast SiGe BiCMOS frontend electronics and hexagonal pixels with 100 {\mu}m pitch. At a sensor bias voltage of 125 V, the detector provides full efficiency and average time resolution of 30, 25 and 17 ps in the overall pixel area for a power consumption of 0.4, 0.9 and 2.7 W/cm^2, respectively. In this first prototype the time resolution depends significantly on the distance from the center of the pixel, varying at the highest power consumption measured between 13 ps at the center of the pixel and 25 ps in the inter-pixel region.

The Picosecond Avalanche Detector is a multi-junction silicon pixel detector based on a $\mathrm{(NP)_{drift}(NP)_{gain}}$ structure, devised to enable charged-particle tracking with high spatial resolution and picosecond time-stamp capability. It uses a continuous junction deep inside the sensor volume to amplify the primary charge produced by ionizing radiation in a thin absorption layer. The signal is then induced by the secondary charges moving inside a thicker drift region. A proof-of-concept monolithic prototype, consisting of a matrix of hexagonal pixels with 100 $\mu$m pitch, has been produced using the 130 nm SiGe BiCMOS process by IHP microelectronics. Measurements on probe station and with a $^{55}$Fe X-ray source show that the prototype is functional and displays avalanche gain up to a maximum electron gain of 23. A study of the avalanche characteristics, corroborated by TCAD simulations, indicates that space-charge effects due to the large primary charge produced by the conversion of X-rays from the $^{55}$Fe source limits the effective gain.

The 235U(n,f) cross section was measured in a wide energy range (25 meV - 170 keV) at the n_TOF facility at CERN, relative to 6Li(n,t) and 10B(n,alpha) standard reactions, with high resolution and accuracy, with a setup based on a stack of six samples and six silicon detectors placed in the neutron beam. In this paper we report on the results in the region between thermal and 10 keV neutron energy. A resonance analysis has been performed up to 200 eV, with the code SAMMY. The resulting fission kernels are compared with the ones extracted on the basis of the resonance parameters of the most recent major evaluated data libraries. A comparison of the n_TOF data with the evaluated cross sections is also performed from thermal to 10 keV neutron energy for the energy-averaged cross section in energy groups of suitably chosen width. A good agreement is found in average between the new results and the latest evaluated data files ENDF-B/VIII and JEFF-3.3, as well as with respect to the IAEA reference files. However, some discrepancies are still present in some specific energy regions. The new dataset here presented, characterized by unprecedented resolution and accuracy, can help improving the evaluations in the Resolved Resonance Region and up to 10 keV, and reduce the uncertainties that affect this region.

A monolithic silicon pixel detector prototype has been produced in the SiGe BiCMOS SG13G2 130 nm node technology by IHP. The ASIC contains a matrix of hexagonal pixels with pitch of approximately 100 $\mu$m. Three analog pixels were calibrated in laboratory with radioactive sources and tested in a 180 GeV/c pion beamline at the CERN SPS. A detection efficiency of $\left(99.9^{+0.1}_{-0.2}\right)$% was measured together with a time resolution of $(36.4 \pm 0.8)$ps at the highest preamplifier bias current working point of 150 $\mu$A and at a sensor bias voltage of 160 V. The ASIC was also characterized at lower bias voltage and preamplifier current.

This paper presents a small-area monolithic pixel detector ASIC designed in 130 nm SiGe BiCMOS technology for the upgrade of the pre-shower detector of the FASER experiment at CERN. The purpose of this prototype is to study the integration of fast front-end electronics inside the sensitive area of the pixels and to identify the configuration that could satisfy at best the specifications of the experiment. Self-induced noise, instabilities and cross-talk were minimised to cope with the several challenges associated to the integration of pre-amplifiers and discriminators inside the pixels. The methodology used in the characterisation and the design choices will also be described. Two of the variants studied here will be implemented in the pre-production ASIC of the FASER experiment pre-shower for further tests.

Starting from experimental studies on alpha-clustering in excited self-conjugate nuclei (from $^{16}$O to $^{28}$Si), temperature and density conditions for such a clustering are determined. Measured temperatures have been found in the range of 5.5 - 6.0 MeV whereas density values of 0.3 - 0.4 times the saturation density are deduced, i.e., 0.046 to 0.062 $fm^{-3}$. Such a density domain is also predicted by constrained self-consistent mean field calculations. These results constitute a benchmark for alpha clustering from self-conjugate nuclei in relation to descriptions of stellar evolution and supernovae., Comment: 7 pages, 3 figures. arXiv admin note: text overlap with arXiv:1602.05827, arXiv:1603.01114

We find a late times approximation for the SYK spectral form factor from a large $N$ steepest descent version of the path integral over two replica collective fields. Main ingredients are a suitable uv regularization of the two replica kinetic operator, the property of its Fourier transform and some spectral analysis of the four point function two replica ladder kernel., Comment: v2: References added

LF-Monopix1 and TJ-Monopix1 are depleted monolithic active pixel sensors (DMAPS) in 150 nm LFoundry and 180 nm TowerJazz CMOS technologies respectively. They are designed for usage in high-rate and high-radiation environments such as the ATLAS Inner Tracker at the High-Luminosity Large Hadron Collider (HL-LHC). Both chips are read out using a column-drain readout architecture. LF-Monopix1 follows a design with large charge collection electrode where readout electronics are placed inside. Generally, this offers a homogeneous electrical field in the sensor and short drift distances. TJ-Monopix1 employs a small charge collection electrode with readout electronics separated from the electrode and an additional n-type implant to achieve full depletion of the sensitive volume. This approach offers a low sensor capacitance and therefore low noise and is typically implemented with small pixel size. Both detectors have been characterized before and after irradiation using lab tests and particle beams., Comment: 7 pages, 8 figures. Proceedings of the 12th International "Hiroshima" Symposium on the Development and Application of Semiconductor Tracking Detectors