Search

Abstract: An electron-microscopy investigation was performed on BaTiO3 nanorods that were processed by sol–gel electrophoretic deposition (EPD) into anodic aluminium oxide (AAO) membranes. The BaTiO3 nanorods grown within the template membranes had diameters ranging from 150 to 200nm, with an average length of 10–50μm. By using various electron-microscopy techniques we showed that the processed BaTiO3 nanorods were homogeneous in their chemical composition. The BaTiO3 nanorods were always polycrystalline and were composed of well-crystallized, defect-free, pseudo-cubic BaTiO3 grains, ranging from 10 to 30nm. No intergranular phases were observed between the BaTiO3 grains. A low-temperature hexagonal polymorph that is coherently intergrown with the BaTiO3 perovskite matrix was also observed as a minor phase. When annealing the AAO templates containing the BaTiO3 sol in an oxygen atmosphere the presence of the hexagonal polymorph was diminished. [Copyright &y& Elsevier]

A Transient Current Technique (TCT) utilizing an IR laser with 100 ps pulse width and beam diameter of FWHM = 8µm was used to evaluate non-irradiated and irradiated p-type silicon micro-strip detectors. The beam was parallel with the surface and perpendicular to the strips (Edge-TCT) so that the electron hole pairs were created at known depth in the detector. Induced current pulses were measured in one of the strips. The pulse shapes were analyzed in a new way, which does not require the knowledge of effective trapping times, to determine drift velocity, charge collection and electric field profiles in heavily irradiated silicon detectors. The profiles were studied at different laser beam positions (depth of carrier generation), voltages and fluences up to 5 · 1015 neutrons cm². A strong evidence for charge multiplication at high voltages was found with the detector irradiated to the highest fluence. [ABSTRACT FROM AUTHOR]

Skeletal elements that are exposed to heavy mechanical loads may provide important insights into the evolutionary solutions to mechanical challenges. We analyzed the microscopic architecture of dactylus claws in the woodlice Porcellio scaber and correlated these observations with analyses of the claws' mineral composition with energy dispersive X-ray spectrometry (EDX), electron energy loss spectroscopy (EELS) and selected area electron diffraction (SAED). Extraordinarily, amorphous calcium phosphate is the predominant mineral in the claw endocuticle. Unlike the strongly calcified exocuticle of the dactylus base, the claw exocuticle is devoid of mineral and is highly brominated. The architecture of the dactylus claw cuticle is drastically different from that of other parts of the exoskeleton. In contrast to the quasi-isotropic structure with chitin-protein fibers oriented in multiple directions, characteristic of the arthropod exoskeleton, the chitin-protein fibers and mineral components in the endocuticle of P. scaber claws are exclusively axially oriented. Taken together, these characteristics suggest that the claw cuticle is highly structurally anisotropic and fracture resistant and can be explained as adaptations to predominant axial loading of the thin, elongated claws. The nanoscale architecture of the isopod claw may inspire technological solutions in the design of durable machine elements subjected to heavy loading and wear., (Copyright © 2016 Elsevier Inc. All rights reserved.)

A simple, low cost, and highly sensitive electrochemical sensor, based on a Nafion/ionic liquid/graphene composite modified screen-printed carbon electrode (N/IL/G/SPCE) was developed to determine zinc (Zn(II)), cadmium (Cd(II)), and lead (Pb(II)) simultaneously. This disposable electrode shows excellent conductivity and fast electron transfer kinetics. By in situ plating with a bismuth film (BiF), the developed electrode exhibited well-defined and separate peaks for Zn(II), Cd(II), and Pb(II) by square wave anodic stripping voltammetry (SWASV). Analytical characteristics of the BiF/N/IL/G/SPCE were explored with calibration curves which were found to be linear for Zn(II), Cd(II), and Pb(II) concentrations over the range from 0.1 to 100.0 ng L(-1). With an accumulation period of 120 s detection limits of 0.09 ng mL(-1), 0.06 ng L(-1) and 0.08 ng L(-1) were obtained for Zn(II), Cd(II) and Pb(II), respectively using the BiF/N/IL/G/SPCE sensor, calculated as 3σ value of the blank. In addition, the developed electrode displayed a good repeatability and reproducibility. The interference from other common ions associated with Zn(II), Cd(II) and Pb(II) detection could be effectively avoided. Finally, the proposed analytical procedure was applied to detect the trace metal ions in drinking water samples with satisfactory results which demonstrates the suitability of the BiF/N/IL/G/SPCE to detect heavy metals in water samples and the results agreed well with those obtained by inductively coupled plasma mass spectrometry., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Titanium dioxide (TiO(2)) rutile nanoparticles were synthesized at temperatures below 100 °C using a gel-sol process that provides control of the final particles' characteristics, such as the nanoparticle size, morphology, crystal structure and crystallinity. The synthesized rutile nanoparticles were analyzed using X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the gel-sol process allows control over the final nanoparticle characteristics with the proper choice of reaction parameters. The most profound influence on the nanoparticles' properties is achieved by the type and concentration of the acid used in the reaction mixture. The gel-sol synthesis resulted in anisotropic rutile nanoparticles that are 60-160 nm long, depending on the reaction parameters, and have an aspect ratio of about 5. A reaction mechanism is presented, explaining the influence of various reaction parameters on the characteristics of the TiO(2) nanoparticles.

A photocatalytic, TiO2-based microreactor is designed and fabricated on a metal-titanium foil. The microchannel is mechanically engraved in the substrate foil, and a double-layered TiO2 anatase film is immobilized on its inner walls with a two-step synthesis, which included anodization and a hydrothermal treatment. X-ray diffraction (XRD) and scanning electron microscopy (SEM) confirm the presence of an approximately 10-μm-thick layer of titania nanotubes and anatase nanoparticles. The SEM and transmission electron microscopy (TEM) of the cross sections show a dense interface between the titanium substrate and the TiO2 nanotubes. An additional layer of TiO2-anatase nanoparticles on the top of the film provides a large, photocatalytic surface area. The metal-titanium substrate with a functionalized serpentine channel is sealed with UV-transparent Plexiglas, and four 0.8-mW UV LEDs combined with a power controller on a small printed-circuit board are fixed over the substrate. The photocatalytic activity and the kinetic properties for the degradation of caffeine are provided, and the longer-term stability of the TiO2 film is evaluated. The results show that after 6 months of use and 3600 working cycles the microreactor still exhibits 60% of its initial efficiency.