Search

Straw pretreatment enhances the cellulose accessibility and increases the methane yield from anaerobic digestion. This study investigated the effects of alkali pretreatments with different chemical agents (NaOH, KOH, and Na2CO3) on the physicochemical and thermal characteristics of barley straw, as well as methane production from codigestion with sewage sludge. Artificial neural network modeling with a feedforward neural network (FFNN) and slime mold optimization (SMO) techniques were used to predict methane production. NaOH pretreatment was shown to be the best pretreatment for removing hemicellulose and lignin and for increasing the cellulose accessibility. Moreover, there was a 2.57-fold higher level of methane production compared to that from codigestion with untreated straw. The removal ratios for the total solids, volatile solids, and chemical oxygen demand reached 59.3, 67.2, and 73.4%, respectively. The modeling results showed that the FFNN-SMO method can be an effective tool for simulating the methane generation process, since training, validating, and testing produced very high correlation coefficients. The FFNN-SMO accurately predicted the amount of methane produced, with an R² of 0.998 and a 3.1x10-5 root mean square error (RMSE). [ABSTRACT FROM AUTHOR]

Prescribed burning is a management tool commonly used in forested ecosystems in the southeastern United States, but the influence of this method on grassland vegetation and wildlife in this geographic region is unknown. During 2009–2015, we conducted a study to determine if the application of prescribed burning and/or long-term biosolid applications alter plant communities and/or wildlife use of grassland areas at Marine Corps Air Station Cherry Point, Havelock, NC. We monitored vegetation growth, measured plant community composition, and documented wildlife activity in four study plots for 3 years after the implementation of annual winter prescribed burns. Prescribed burning reduced the amount of litter, increased bare ground during spring, and altered the plant community composition relative to areas that were not burned. Overall, prescribed burning did not alter (F1,803 = 0.37, p = 0.54) bird use of the airfield grasslands, while the long-term application of biosolids resulted in higher (F1,803 = 17.61, p < 0.01) bird use. Few species-specific differences in avian use of prescribed burned and unburned grasslands were found. In contrast, white-tailed deer (Odocoileus virginianus) use of areas that were burned in winter, as well as the adjacent unburned areas, was drastically reduced. Winter prescribed burning appeared to remove forage plants at the time of year deer would use them the most. Our findings suggest that prescribed burning and biosolid applications, used alone and in combination, might be viable grassland management tools for altering wildlife use of grassland areas, specifically white-tailed deer; however, similar research at additional locations should be conducted. [ABSTRACT FROM AUTHOR]

The concentration of viruses in sewage sludge is significantly higher (10–1000-fold) than that found in natural environments, posing a potential risk for human and animal health. However, the composition of these viruses and their role in the transfer of pathogenic factors, as well as their role in the carbon, nitrogen, and phosphorus cycles remain poorly understood. In this study, we employed a shotgun metagenomic approach to investigate the pathogenic bacteria and viral composition and function in two wastewater treatment plants located on a campus. Our analysis revealed the presence of 1334 amplicon sequence variants (ASVs) across six sludge samples, with 242 ASVs (41.22% of total reads) identified as pathogenic bacteria. Arcobacter was found to be the most dominant pathogen accounting for 6.79% of total reads. The virome analysis identified 613 viral genera with Aorunvirus being the most abundant genus at 41.85%. Approximately 0.66% of these viruses were associated with human and animal diseases. More than 60% of the virome consisted of lytic phages. Host prediction analysis revealed that the phages primarily infected Lactobacillus (37.11%), Streptococcus (21.11%), and Staphylococcus (7.11%). Furthermore, our investigation revealed an abundance of auxiliary metabolic genes (AMGs) involved in carbon, nitrogen, and phosphorus cycling within the virome. We also detected a total of 113 antibiotic resistance genes (ARGs), covering major classes of antibiotics across all samples analyzed. Additionally, our findings indicated the presence of virulence factors including the clpP gene accounting for approximately 4.78%, along with toxin genes such as the RecT gene representing approximately 73.48% of all detected virulence factors and toxin genes among all samples analyzed. This study expands our understanding regarding both pathogenic bacteria and viruses present within sewage sludge while providing valuable insights into their ecological functions. [ABSTRACT FROM AUTHOR]

It is desirable to recycle sewage sludge as fertilizer for agricultural fields. The application of sludge to agricultural soils is a measure that replaces chemical fertilizers and plays an important role in improving soil's physicochemical and biological properties. However, there are concerns that the pollutants in sewage sludge will cause negative impacts on soil health. To closely monitor the soil–sludge interactions, a field study was conducted over a 20-year period in the North China Plain. In this study, the long-term effects of sewage sludge on the soil properties and soil microbial diversity were investigated. We examined the effects of various fertilization methods (control, chemical fertilizer, uncomposted sludge fertilizer, composted sludge fertilizer) on wheat production and several soil health indicators, such as the soil's enzymatic activities, microbial biomass, microbial diversity, and crop yield. This long-term experiment supports that the composted sludge fertilizer increased crop production by 124.2% compared to the control treatment. The soil's biological quality (e.g., the concentration of soil microbial biomass carbon) was also improved under the composted sludge fertilizer treatment. The concentrations of soil microbial biomass carbon under the uncomposted sludge fertilizer and composted sludge fertilizer treatments were 560.07 mg/kg and 551.07 mg/kg, respectively. The effect of the composted sludge fertilizer was greater than that of the uncomposted sludge fertilizer. The content of heavy metals did not exceed the national standard. The highest soil health index was 0.79 with the composted sludge fertilizer. Therefore, these results suggest that the application of composted sludge fertilizer has the potential to enhance long-term soil health and promote sustainable agricultural practices. [ABSTRACT FROM AUTHOR]

In many countries around the world, the thermal treatment of waste plays an important role in the waste-management system. As a result, electricity and heat are produced. However, solid residues are produced in the form of bottom ash, fly ash (FA) and air pollution control (APC) residues. Alternative raw material resources are currently being sought, one of which may be anthropogenic materials from waste thermal treatment processes. This paper presents the results of a study on the trace element content of FA and APC residues from three different installations: municipal solid waste incineration (grate boiler), sewage sludge (fluidized bed boiler) and hazardous waste (rotary kiln). Research methods such as ICP-MS (inductively coupled plasma mass spectrometry), ICP-AES (inductively coupled plasma/atomic emission spectroscopy) and XRD (X-ray diffraction) were used. The results obtained indicate that the chemical composition of FA and APC residues depends mainly on the type of waste being converted, the thermal process and the flue gas treatment method. Ash from sewage sludge incineration in particular contains significant amounts of P and Sb - elements classified as critical raw materials (CRM). In addition, they also contain other valuable metals such as Ag and Zn, in amounts far exceeding the average crustal abundance. In addition, residues from the incineration of hazardous waste may pose a potential risk to the environment due to the presence of significant amounts of heavy metals such as Pb, Cd and Hg. [ABSTRACT FROM AUTHOR]

Liquid biofuels like biodiesel and bioethanol are crucial in the transition to low-carbon and high-energy alternatives to fossil fuels. One significant by-product of biodiesel production is glycerol, which accounts for about 10% of the total conversion output. While waste glycerol poses challenges due to its impurities and contaminants, it also holds potential as a metabolic resource for essential cellular components in microorganisms. Crude glycerol production is reviewed, highlighting relevance in current biodiesel technologies and its biochemical composition. To efficiently utilize waste glycerol, co-valorization with low-cost substrates through biocircular platforms using various microorganisms or insects for second and third-generation oxy-biofuels has been explored. Among these, the black soldier fly larvae have demonstrated higher competitiveness for lipid contents (35–43%), making them a promising organism for recycling waste glycerol into biodiesel production, alongside microalgae and oleaginous yeast. The microbial biodiesel productivity from oleaginous yeast is notably higher (3546 kg ha−1 y−1) than soybean biodiesel (562 kg ha−1 y−1), while microalgal biodiesel productivity surpasses palm biodiesel by more than 25 times. Remarkably, black soldier fly larvae biodiesel productivity was reported to be ~ 1.7 times higher than microalgae and an impressive ~ 43 times higher than palm biodiesel. Despite their potential for biodiesel production, waste glycerol from biodiesel industry still represents a challenge because of high impurities, high viscosity, and limited direct applications in existing processes. To further enhance energy sustainability and address the challenge of waste glycerol, biocircular platforms are discussed for waste glycerol utilization with domestic wastewater sludge, lignocellulosic biomass, and protein-rich wastes. These platforms offer opportunities to create other sustainable agricultural products while minimizing their environmental footprint. [ABSTRACT FROM AUTHOR]

Low‐carbon alkaline thermal hydrolysis of sewage sludge for the production of high‐quality plant‐growth‐promoting nutrients and biostimulants is a growing concern for sludge resource utilization in agriculture. Thus, this study aims to investigate functional characteristics and soil biochemical effects of sewage sludge‐derived nutrients and biostimulants (SS‐NB). The content of heavy metals in SS‐NB decreased by 47.39–100%, and an increase in soil protease, invertase, and soil nutrient utilization rates are observed in SS‐NB groups. SS‐NB substituted for chemical fertilizer increased the diversity and evenness of microbial community and reduced the abundance of the soil‐borne bacterial genus Arthrobacter. The dominant community of SS‐NB100 group is mainly enriched in Microvirga, Ensifer, Novosphingobium, Bosea and Ellin6055, which are principally beneficial symbiotic bacteria of plants and participated in C and N cycles. Moreover, SS‐NB reduced the accumulation of Ktedonobacteria and Nitrosospira, which are involved in the production of CO2 and N2O, and also enhanced the coordination of soil microorganisms with enzyme activities and nutrient utilization rate. In conclusion, the results suggest that SS‐NB exerts a positive effect on reducing greenhouse gas emissions and preventing soil‐borne diseases, and can further enhance collaboration with soil enzyme activity and soil nutrient utilization by stimulating soil microorganisms. [ABSTRACT FROM AUTHOR]

The recent SARS‐CoV‐2 outbreak yielded substantial data regarding virus fate and prevalence at water reclamation facilities (WRFs), identifying influential factors as natural decay, adsorption, light, pH, salinity, and antagonistic microorganisms. However, no studies have quantified the impact of these factors in full scale WRFs. Utilizing a mass balance approach, we assessed the impact of natural decay and other fate mechanisms on genetic marker removal during water reclamation, through the use of sludge and wastewater genetic marker loading estimates. Results indicated negligible removal of genetic markers during P/PT (primary effluent (PE) p value: 0.267; preliminary and primary treatment (P/PT) accumulation p value: 0.904; and thickened primary sludge (TPS) p value: 0.076) indicating no contribution of natural decay and other fate mechanisms toward removal in P/PT. Comparably, adsorption and decomposition was found to be the dominant pathway for genetic marker removal (thickened waste activated sludge (TWAS) log loading 9.75 log10 GC/day); however, no estimation of log genetic marker accumulation could be carried out due to high detections in TWAS. Practitioner Points: The mass balance approach suggested that the contribution of natural decay and other fate mechanisms to virus removal during wastewater treatment are negligible compared with adsorption and decomposition in P/PT (p value: 0.904).During (P/PT), a higher viral load remained in the (PE) (14.16 log10 GC/day) compared with TPS (13.83 log10 GC/day); however, no statistical difference was observed (p value: 0.280) indicting that adsorption/decomposition most probably did not occur.In secondary treatment (ST), viral genetic markers in TWAS were consistently detected (13.41 log10 GC/day) compared with secondary effluent (SE), indicating that longer HRT and the potential presence of extracellular polymeric substance‐containing enriched biomass enabled adsorption/decomposition.Estimations of total solids and volatile solids for TPS and TWAS indicated that adsorption affinity was different between solids sampling locations (p value: <0.0001). [ABSTRACT FROM AUTHOR]

Extreme thermophiles Calditerricola satsumensis DD2 and D3 were isolated from mesothermal municipal sludge, a material used for hyperthermal composting. To understand the ecologically anomalous findings, their behavior at various temperatures, membrane fatty acid composition, and draft genome sequences were compared with those of C. satsumensis YMO81T and Calditerricola yamamurae YMO722T, already isolated from hyperthermal compost. All four strains grew between 56 and 83 °C. However, strains DD2 and D3 were stable for ≥48 h at a wide range of temperatures (20–75 °C), while strains YMO81T and YMO722T were highly labile at lower temperatures. The former strains maintained their colony-forming ability for >180 days at 20 °C, while the latter strains lost it within 1 d. All four strains showed similar composition of membrane fatty acid, which were not affected by 20 °C treatment. Comparative draft genome analyses showed that 13 candidate genes were present only in strains DD2 and D3, and the specific expression of six gene homologs was confirmed. A DNA chaperone, site-specific recombinase XerD homolog, had tetra adenine sequence at its upper gene region, and was up-regulated by 20 °C treatment in DD2 and D3, suggesting a possible role in the cold tolerance of sludge-derived strains. In addition, the lack of another possible DNA chaperone, a homolog of the ATP-dependent DNA helicase, in the compost-derived strains may accelerate their sensitivity to cold shock. In conclusion, we speculate that the specific phenotypic and genotypic characteristics of sludge-derived strains are responsible for their unusual ecological distribution at ambient temperatures. [ABSTRACT FROM AUTHOR]

Biosolids and Dairy Shed Effluent (DSE) can contain high concentrations of plant nutrients, making them potential resources for enhancing forest tree species growth and soil fertility. This study aimed to investigate the effects of biosolids and DSE application on the growth and nutrient uptake of Leptospermum scoparium and Kunzea robusta, while also considering the potential accumulation of contaminants. The results demonstrated that amending low-fertility soil with 2600 kg N ha-1 of biosolids and 200 kg N ha-1 of DSE positively influenced the growth of both L. scoparium and K. robusta. This improvement was evident through increased biomass production and enhanced uptake of essential elements such as calcium (Ca), potassium (K), and sulfur (S). Notably, L. scoparium exhibited superior growth when combined with DSE, while both species showed similar positive responses when combined with biosolids. However, it should be noted that the application of biosolids resulted in elevated concentrations of certain trace elements in the plants, whereas DSE did not. These trace elements included cadmium (Cd), copper (Cu), manganese (Mn), and zinc (Zn). Despite the increase, the levels of these elements did not exceed unacceptable thresholds. Considering the potential influence of biosolids on plant rhizodeposition, it is recommended that future studies investigate the interactions between plant roots and microbes, particularly in relation to plant element uptake. This line of research would further enhance our understanding of the underlying mechanisms involved. In conclusion, the findings suggest that the application of biosolids and DSE can effectively improve forest tree growth and nutrient uptake. However, careful management is necessary to mitigate the potential accumulation of trace elements. These results provide valuable insights for optimizing the use of biosolids and DSE in forestry practices, with potential economic and environmental benefits. [ABSTRACT FROM AUTHOR]

The application of biosolids to agricultural land has been identified as a major pathway of microplastic (MP) pollution to the environment. Very little research, however, has been done on the MP content of biosolids within Canada. Fifteen biosolid samples from different treatment processes (liquid, dewatered, pelletized, and alkali‐stabilized) were collected from 11 sources across southern Ontario to quantify and characterize the MP load within them. All samples exhibited MP concentrations ranging from 188 200 (±24 161) to 512 000 (±28 571) MPs/kg dry weight and from 4122 (±231) to 453 746 (±38 194) MPs/kg wet weight. Field amendment of these biosolids can introduce up to 3.73 × 106 to 4.12 × 108 MP/ha of agricultural soil. There was no significant difference in the MP concentrations of liquid, dewatered, and pelletized samples; but a reduction in MP content was observed in alkali‐stabilized biosolids. Fragments composed 57.6% of the MPs identified, while 36.7% were fibers. In addition, MPs showed an exponential increase in abundance with decreasing size. Characterization of MPs confirmed that polyester was the most abundant, while polyethylene, polypropylene, polyamide, polyacrylamide, and polyurethane were present across the majority of biosolid samples. The results of the present study provide an estimate of the potential extent of MP contamination to agricultural fields through the amendment of biosolids. Environ Toxicol Chem 2024;43:793–806. © 2023 The Authors. Environmental Toxicology and Chemistry published by Wiley Periodicals LLC on behalf of SETAC. [ABSTRACT FROM AUTHOR]

This work explores the effects of the temperature (250, 280, 310°C), time (20, 40, 60 min), sewage sludge mixing ratio (25, 50, 75%) on the solid fuel quality and yield of the biochar produced from sewage sludge blended with pine sawdust. The optimal conditions for the torrefaction of sewage sludge and pine sawdust were investigated by the response surface methodology. Mathematical models were developed on the weight yield, high heating value and ash content and experimental data were examined through analysis of variance. The results depicted that the effects of temperature and mixing ratio were more considerable than residence time for the three response variables. The optimum point for weight yield, HHV, ash were predicted to be 60.82%, 21.58 MJ kg-1 and 18.78% at 310°C, 20 min and sewage sludge mixing ratio of 25%, respectively. The experimental results show that the average values of the experiments were 56.4%, 22.9 MJ kg-1, and 21% for weight yield, HHV and ash content, respectively. [ABSTRACT FROM AUTHOR]

Polycyclic aromatic hydrocarbons (PAHs) are widely present in the environment, causing increasing concern because of their impact on soil health, food safety and potential health risks. Four bioremediation strategies were examined to assess the dissipation of PAHs in agricultural soil amended with sewage sludge over a period of 120 days: soil-sludge natural attenuation (SS); phytoremediation using maize (Zea mays L.) (PSS); mycoremediation (MR) separately using three white-rot fungi (Pleurotus ostreatus , Phanerochaete chrysosporium and Irpex lacteus) ; and plant-assisted mycoremediation (PMR) using a combination of maize and fungi. In the time frame of the experiment, mycoremediation using P. chrysosporium (MR-PH) exhibited a significantly higher (P < 0.05) degradation of total PAHs compared to the SS and PSS treatments, achieving a degradation rate of 52 %. Both the SS and PSS treatments demonstrated a lower degradation rate of total PAHs, with removal rates of 18 % and 32 %, respectively. The PMR treatments showed the highest removal rates of total PAHs at the end of the study, with degradation rates of 48–60 %. In the shoots of maize, only low- and medium-molecular-weight PAHs were found in both the PSS and PMR treatments. The calculated translocation and bioconversion factors always showed values < 1. The analysed enzymatic activities were higher in the PMR treatments compared to other treatments, which can be positively related to the higher degradation of PAHs in the soil. [ABSTRACT FROM AUTHOR]

This article provides a comprehensive exploration of the imperative necessity for coupling the utilization of low-rank coal, sewage sludge, and straw. It studies the challenges and limitations of individual utilization methods, addressing the unique hurdles associated with feedstocks. It focused on achieving integrated and sustainable resource management, emphasizing efficient resource utilization, waste minimization, and environmental impact reduction. The investigation extends to the intricate details of reaction processes in co-processing, with a specific emphasis on the drying of raw materials to enhance combustion characteristics. The molding and preparation of feedstock are dissected, encompassing raw material selection, mixing, and the crucial addition of additives and binders. The proportions and homogenization of these feedstocks are intricately examined for uniformity and effectiveness. Furthermore, it presents theoretical approaches for investigating the co-combustion of these diverse feedstocks, contributing a solid foundation for future studies in this dynamic field. The findings presented in it offer valuable insights for researchers, practitioners, and policymakers seeking sustainable solutions in the co-disposal technology of these feedstocks. Therefore, it provides a holistic understanding of the challenges and opportunities in coupling the utilization of these selected feedstocks. By addressing individual limitations and emphasizing integrated resource management, the article establishes the groundwork for sustainable and efficient co-processing practices. The exploration of reaction processes gives a comprehensive framework for future research and application in the field of co-combustion technology. The insights gleaned from this study contribute significantly to advancing knowledge in the sustainable utilization of diverse feedstocks, guiding efforts towards environmentally responsible and resource-efficient practices. [ABSTRACT FROM AUTHOR]

This research aimed at evaluating the performance of faecal sludge briquettes on the quality of briquettes produced in terms physical and combustion properties. Specifically, the research determined the physical and combustion properties of briquette produced from faecal sludge bond with cassava peel, sunflower cake, banana peel and waste paper binders. Physical and combustion properties of the binder materials and briquettes produced were analysed in the Water Resource Engineering laboratory. The laboratory analysis of the combustion properties showed that the Sunflower cake binder had highest calorific value of 16.24 MJ/Kg when compared to other binders including banana peels, cassava peels and waste papers. Similarly, sunflower cake bond briquettes were found to have highest calorific value of 10.81 MJ/Kg than other binders bound briquettes. The drying rates were higher for waste paper, a bond briquette which was observed to be within 6 days from the day of briquette production. The density of faecal sludge briquette was higher in banana peels bond briquettes having the density of 0.99±0.062 g/cm³. The use of binders has significantly improved the physical and combustion properties and thus the performance of the faecal sludge derived briquettes. It is recommended to use faecal sludge bond with sunflower cake binder. [ABSTRACT FROM AUTHOR]

Biostimulants are substances or microorganisms that are applied to plants, soil, or seeds, to improve the growth, development, performance, and quality of crops. Their application is mainly directed towards improving the resistance of crops against abiotic and biotic stresses. These compounds are formulated from a great variety of compounds: humic substances, complex organic materials (sewage sludge extracts, composts, and manure), chemical elements (Al, Co, Na, Se, and Si), inorganic salts including phosphite, seaweed extracts (brown, red, and green), amino acids, etc. As of today, it has been observed that corn steep liquor (CSL), which is obtained from the industrial process of corn transformation, may be a good ingredient for the formulation of biostimulant products. CSL contains a large amount of different chemical compounds with biological activity for the plants and soil. The use of CSL industrial waste, previously formulated, could have a direct or indirect effect on the physiological processes and metabolic routes of plants related to the adaptation to abiotic and biotic stresses, as their compounds are part of these metabolic pathways, act as elicitor compounds, and/or have their own biological activity in the plants. There is evidence that the application of CSL could protect plants from specific abiotic and biotic stresses, such as an excess of light or temperature, nutritional limitations, salinity, drought, or pathogens. In addition, it can improve the growth of the plant when these are grown in hydroponic systems, and can improve the health of soils. The present article is focused on describing the most relevant scientific aspects of CSL when used as an ingredient to formulate biostimulants for agriculture. It will discuss its chemical composition, the analytical techniques utilized to elucidate and quantify its compounds, its uses in agriculture, and mode of action in the plants. [ABSTRACT FROM AUTHOR]

The production of municipal sludge is steadily increasing in line with the production of sewage. A wealth of organic contaminants, including nutrients and energy, are present in municipal sludge. Anaerobic fermentation can be used to extract useful resources from sludge, producing hydrogen, methane, short-chain fatty acids, and, via further chain elongation, medium-chain fatty acids. By comparing the economic and use values of these retrieved resources, it is concluded that a high-value resource transformation of municipal sludge can be achieved via the production of medium-chain fatty acids using anaerobic fermentation, which is a hotspot for future research. In this study, the selection of the pretreatment method, the method of producing medium-chain fatty acids, the influence of the electron donor, and the technique used to enhance product synthesis in the anaerobic fermentation process are introduced in detail. The study outlines potential future research directions for medium-chain fatty acid production using municipal sludge. These acids could serve as a starting point for investigating other uses for municipal sludge. [ABSTRACT FROM AUTHOR]

In this research, we look into the use of dried sewage sludge biomass in its crude form generated from a municipal wastewater treatment plant localized in Mascara (West of Algeria) when it comes to the elimination of methylene blue (MB) from artificial wastewater aqueous solutions in batch process. Moreover, the sewage sludge biomass was characterized by different techniques such as Fourier transform infrared (FTIR), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), and thermal gravimetric analysis (TGA). In order to optimize the removal of methylene blue (MB) by the present adsorbent, various parameters were explored, including pH effect, initial methylene blue (MB) concentration, adsorbent dose, temperature, and contact time.The results revealed the presence of abundant functional groups (–COOH) responsible for methylene blue (MB) adsorption by electrostatic attraction, optimal pH = 5, and optimal sewage sludge biomass concentration of 2 g/l. The maximum measured adsorption capacity of methylene blue on the sewage sludge biomass was about qe = 325 mg/g at 20 min of contact time. Based on the R2, X2, RMSE, Average relative error (ARE) coefficients, the pseudo-second-order kinetic model and Langmuir model describe well the experimental kinetic and equilibrium data. The application of the Weber and Morris model to the kinetic data shows that the overall mass transfer rate was controlled simultaneously by film diffusion and intraparticle or pore diffusion. The value of intra-particle or pore diffusion coefficient was found to be Kp (mg/g min0.5) = 0.112. On the basis of energy used in the adsorption process and estimated value from Temkin model, adsorption is considered to be a physical process. The thermodynamic analysis revealed that the adsorption mechanism was spontaneous and endothermic, as reflected by the ΔG° and ΔH° values obtained. Hence, the proposed sewage sludge biomass can be used as a low-cost adsorbent to remove methylene blue (MB) from a variety of polluted water samples, and it can also be used to remove other cationic dyes. [ABSTRACT FROM AUTHOR]

Hydrothermal carbonization (HTC) has developed considerably over the last 15 years and offers a viable alternative for the utilization of municipal and industrial organic waste such as sewage sludge. However, the technology has yet to establish itself as a valorization process for waste biomasses (2024) and is not yet a recognized state of the art. Nevertheless, the HTC technology could gain greater relevance in the future, especially as an alternative valorization pathway for sewage sludge. During HTC, significant amounts of HTC process water (PW) are produced as a byproduct. The process water is inorganically and organically polluted and has to be treated, as it would be a burden on water bodies and thus on the environment if left untreated. In the EU and specifically Germany, industrial wastewater producers like HTC-plant operators are obliged to treat their industrial wastewater before discharging it into the environment. In addition to a large amount of PW and its treatment to the required limits, the organic load and possible persistent and toxic substances pose major challenges for plant operators. Many proven processes from industrial wastewater treatment were transferred for the treatment of PW. Treatment of the PW in a manner that is industrially viable, economically viable, and efficient is crucial for the effective commercialization of HTC technology. In this, the challenges and opportunities of PW composition, management, and treatment, including legal aspects, are mainly discussed. Therefore, the legal framework in the European Union and specifically for Germany will be elaborated. Furthermore, different treatment pathways are also highlighted. [ABSTRACT FROM AUTHOR]

In order to improve the combustion characteristics of municipal waste materials and reduce excess pollutants generated during the incineration process, this study develops a novel waste incinerator with an α-shaped flue gas route. This has been achieved through the application of momentum vector synthesis theory in order to modify the secondary air structure in a conventional incinerator, resulting in enhanced combustion efficiency of the incinerator. Computational Fluid Dynamics (CFD) based cold state test results demonstrate that with appropriate modifications to the design of the incinerator, the flue gas propagates through a longer α-shaped route rather than conventional L-shaped route. Hot state tests have been carried out on a full scale 750 tons/day waste incinerator. Test rests show that the temperature of the flue gas increases by 138% under the front arch when secondary air supply is being incorporated into the design of the incinerator, resulting in better combustion of the municipal waste materials, lower emissions and higher thermal efficiency of the incinerator. The results obtained in this study confirm the rationality and feasibility of momentum flow rate method for better design of waste incinerators. [ABSTRACT FROM AUTHOR]

Sewage sludge was considered a critical reservoir for the propagation of antibiotic resistance genes (ARGs) and its treatment and disposal were important for the environment and human health. This study investigated the efficiency of the bioleaching technology for reducing eight typical antibiotic resistance genes in municipal sewage sludge, which was an emerging environmentally friendly technology for sludge dewatering. The prevalence of forty ARGs subtypes (including two mobile gene elements, MEGs) and one 16SrRNA gene were concerned with high throughput quantitative polymerase chain reaction during sludge bioleaching and a total of sixteen ARGs subtypes (including two transposase genes) were presented in the sludge samples. These genes were significantly decreasing after bioleaching, namely, one sulfonamide resistance gene (sul2), five tetracycline resistance genes (tetA-02, tetB-01, tetG-01, tetO-01, tetX), four macrolide-lincosamide-streptogramin B (MLSB) resistance genes (ermF, mphA-01, mphA-02, lnuB-01), two β-lactam resistance genes (blaOXA1/blaOXA30, blaPSE), two aminoglycoside resistance genes [aac(6´)-Ib, strB] and two MEGs (tnpA-01, tnpA-03). This result indicated that the bioleaching technology could significantly reduce the ARGs abundance of sewage sludge and the maximum removal efficiency was sixty-eight percent (mphA-02) and other ARGs subtypes such as tetA-02, tetB-01, mphA-01 and blaOXA1/blaOXA30 were decreased over fifty percent. The characteristics of Acidithiobacillus ferrooxidans contributed to the sludge bioleaching and may influence the diversity and composition of bacterial community and consequentially result in the change of ARGs abundance. [ABSTRACT FROM AUTHOR]

Copyright of Industrial Water Treatment is the property of CNOOC Tianjin Chemical Research & Design Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Industrial Water Treatment is the property of CNOOC Tianjin Chemical Research & Design Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Industrial Water Treatment is the property of CNOOC Tianjin Chemical Research & Design Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Industrial Water Treatment is the property of CNOOC Tianjin Chemical Research & Design Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The development of civilization is causing an increase in the amount of industrial wastes, especially hazardous wastes. Among the methods of utilisation of this type of waste, the methods of stabilisation and solidification deserve attention, which enable the transformation of hazardous waste and the heavy metals it contains into an environmentally safe form, that is, immobilised. This paper proposes a method to stabilize and solidify galvanic sludge using geopolymerization reactions. The surface morphology was studied, and the chemical composition was analyzed using the SEM-EDS method. The presence of characteristic functional groups on the surface of the galvanic sludge and the geopolymer obtained on its basis was determined by FTIR spectroscopic analysis. Moreover, we evaluated of the recovery of selected heavy metals were performed on the basis of leaching tests. It was found that, as a consequence of geopolymerization of galvanic sludge, this hazardous waste is transformed in such a way that the heavy metals it contains, which occur in the form of soluble compounds are immobilised. In relation to the metals analyzed, reduction in solubility were obtained at a practical level of 100% for Zn and Mn, for the remaining metals, respectively, 94% for Cu and in the range of 40 to 90% for Pb. Analysis of the FTIR spectra showed that the ions of the metals studied were permanently immobilised in the aluminosilicate structure of the geopolymers obtained. This shows, that galvanic sewage sludge, as hazardous waste, is chemically transformed into inert waste that may be deposited in landfills. [ABSTRACT FROM AUTHOR]

Purpose: The use of sewage sludge associated with natural rock-based fertilizers can increase nutrient solubility and soil fertility. From this perspective, this study evaluated changes in the chemical soil attributes and the nutrient availability rate after the application of sewage sludge, natural phosphate, and elemental sulfur in soils with different clay contents. Method: The study was conducted in a controlled environment and was set up in a completely randomized design with four replications in a 3 x 5 x 5 factorial arrangement consisting of soil with three clay contents: 28%, 34%, and 42%; five fertilization managements: unfertilized (Control), fertilized with natural phosphate (NF), fertilized with sewage sludge (SS), fertilized with natural phosphate and elemental sulfur (NF+S), and fertilized with NF+S+SS; and five evaluation times: 0, 30, 60, 90, and 120 days after fertilization. The chemical soil attributes and the nutrient availability rate were evaluated. Results: The application of sludge, natural phosphate, and sulfur increased the contents of SOM, N, P, K, Ca, Mg, Al, H + Al, SB, and CEC and reduced the soil pH, in addition to favoring the rate and time of availability of P, Ca, and Mg, with means higher than 50% in the soils from 30 to 120 days after application. At 120 days after application of sludge, the average availability rate of P, K, Ca, and Mg corresponded to 37, 13, 144, and 157%, respectively. Conclusion:These improvements imply savings with mineral fertilizers and contribute to adopting conservationist and sustainable practices. The individual application of sewage sludge or its application with natural phosphate and elemental sulfur increased soil fertility and the nutrient availability rate in soils with different clay contents. [ABSTRACT FROM AUTHOR]

BACKGROUND: To our best knowledge, no experimental study has previously investigated the simultaneous effects of adding Fe powder for the decrease of hydrogen sulfide (H2S) in biogas and the removal of phosphate (PO4‐P) in continuous anaerobic digestion (AD). This study investigated the effects of iron (Fe) powder (5 g L−1) in AD to remove H2S and PO4‐P. A comparative experiment was conducted using two semi‐continuous‐flow anaerobic digesters treating primary sludge at decreasing hydraulic retention times (HRTs) of 20 to 10 days. RESULTS: The addition of Fe powder to AD removed > 98% of H2S at all HRTs, and removed 64–72% of PO4‐P, with the highest removal efficiency at HRT = 10 d. The addition of Fe powder to AD had no noticeable effect on biogas production or pH, but it increased the CH4 content (62.7–66.0% in Fe‐treated vs 58.2–60.4% in the Control) partly due to the greater presence of Methanoregulaceae. The relative abundance of the microbial groups was more affected by HRT than by the addition of Fe powder. The presence of Fe powder notably increased the abundance of Spirochaetaceae and Syntrophaceae. CONCLUSION: As shown, the addition of Fe powder can improve the management of both H2S in the biogas and PO4‐P in the digested sludge in the AD system. © 2024 Society of Chemical Industry (SCI). [ABSTRACT FROM AUTHOR]

FePO4 is a common source of P in secondary resources and can be found in sewage sludge, phosphating slag, and spent LiFePO4 batteries. Effective circulation of P in FePO4-bearing solid waste is essential for P sustainability. As a fundamental study to develop a technology for recycling P as P4 in FePO4-bearing solid wastes through molten salt electrolysis, this work focuses on investigating the dissolution behavior of solid FePO4 in molten CaCl2. Excessive solid FePO4 was introduced into molten CaCl2 from 1073 K to 1253 K, and the melt composition was monitored for 156 hours. The result indicates the formation of Ca2PO4Cl, FeCl2, and Cl2. Ca2PO4Cl further dissolves into the melt as soluble ions, while FeCl2 and Cl2 escape as volatiles. The dissolution of FePO4 in molten CaCl2 is significantly faster compared to other metal phosphates. Concentration analysis reveals an initial rapid increase followed by a subsequent decrease in both P and total Fe concentrations in the melt. At 1123 K, the Fe content reaches a peak value of 4.4 mass pct in 1 hour, indicating a complete reaction between solid FePO4 and molten CaCl2. The P content also reaches a peak of 2.1 mass pct in 1 hour, exceeding the solubility of P in molten CaCl2. This can be attributed to the suspension of fine solid Ca2PO4Cl particles in the melt. The dissolution can be described as explosive at the beginning due to the rapid formation of high-pressure gas bubbles (Cl2 and FeCl2). Adding Fe(II) accelerates the dissolution of PO43-, although the solubility of P is independent of Fe ions. These findings provide a foundation for developing practical technologies that enable the isolation of P4 from FePO4-bearing solid wastes. [ABSTRACT FROM AUTHOR]

The immobilisation of bacteria on biochar has shown potential for enhanced remediation of petroleum hydrocarbon-contaminated soil. However, there is a lack of knowledge regarding the effect of bacterial immobilisation on biosolids-derived biochar for the remediation of diesel-contaminated soil. This current study aimed to assess the impact of the immobilisation of an autochthonous hydrocarbonoclastic bacteria, Ochrobacterium sp. (BIB) on biosolids-derived biochar for the remediation of diesel-contaminated soil. Additionally, the effect of fertiliser application on the efficacy of the BIB treatment was investigated. Biochar (BC) application alone led to significantly higher hydrocarbon removal than the control treatment at all sampling times (4887–11,589 mg/kg higher). When Ochrobacterium sp. was immobilised on biochar (BIB), the hydrocarbon removal was greater than BC by 5533 mg/kg and 1607 mg/kg at weeks 10 and 22, respectively. However, when BIB was co-applied with fertiliser (BIBF), hydrocarbon removal was lower than BIB alone by 6987–11,767 mg/kg. Quantitative PCR (q-PCR) analysis revealed that the gene related to Ochrobacterium sp. was higher in BIB than in the BC treatment, which likely contributed to higher hydrocarbon removal in the BIB treatment. The results of the q-PCR analysis for the presence of alkB genes and FTIR analysis suggest that the degradation of alkane contributed to hydrocarbon removal. The findings of this study demonstrate that bacterial immobilisation on biosolids-derived biochar is a promising technique for the remediation of diesel-contaminated soil. Future studies should focus on optimising the immobilisation process for enhanced hydrocarbon removal. [ABSTRACT FROM AUTHOR]

Fe-containing sludge biochar produced by pyrolysis of Fe-containing residual municipal sludge was utilized for removing Cr(VI) from aqueous solutions. It was observed that increasing the solution pH decreased the adsorption performance of FSBC for Cr(VI), while raising the adsorption temperature enhanced Cr(VI) removal on FSBC. The coexisting ions of Na+, K+, SO42- and NO3- had minimal impact on removing Cr(VI) by FSBC, whereas the divalent cation of Ca2+ and Mg2+ exhibited a slight inhibitory influence on removing Cr(VI). Both the pseudo-first-order and Langmuir model were found to better describe the Cr(VI) removal process on FSBC from aqueous solutions. The mechanisms involved in removing Cr(VI) by FSBC may include complexation, electrostatic interaction and reduction processes. The Fe species present on FSBC were identified as both Fe2O3 and Fe3O4, with Fe3O4 disappearing after removing Cr(VI). The Fe species on FSBC provided Fe-O groups as site for removing Cr(VI), while Fe3O4 facilitated the Cr(VI) reduction by FSBC. This findings offered further viewpoints into removing Cr(VI) from aqueous solutions using Fe-containing sludge biochar. [ABSTRACT FROM AUTHOR]

The increase in the standard of living and economic development of cities and smaller settlement units implies the extension and modernization of infrastructure, including wastewater collection and treatment systems, which is closely related to the protection of surface water and groundwater. This study analyzes the effects of the modernization of two wastewater treatment plants carried out between 2019 and 2020. These are the municipal wastewater treatment plants for Rawicz and Kościan in the Wielkopolska region. The analysis of contamination indicators and wastewater treatment efficiency showed that in both plants, the modernization and extension of wastewater treatment and sludge treatment technologies resulted in improved treated wastewater parameters and better sludge preparation for use. The high efficiency of contaminant removal (mostly above 94%) improves the standard of living, intensifies care for the environment, and increases the attractiveness of the agglomerations served by the analyzed plants. The obtained results were confirmed by statistical tests. [ABSTRACT FROM AUTHOR]

Microplastics have been widely detected in wastewater treatment plants, but there is still a significant dearth of research data on the removal efficiency of microplastics in such plants. The present study focused on three wastewater treatment plants situated in Zhengzhou, China. On-site sampling and Raman spectrum detection techniques were employed to identify microplastics in both wastewater and sludge samples, while the removal efficiency of microplastics was quantified for each plant. Results showed that the abundance of microplastics in influent exhibited ranging from 147.5 ± 2.6 to 288.8 ± 11.8 n/L, while the range in sludge samples was from 12,024.7 ± 1737.0 n/kgdw to 20,818.4 ± 5662.0 n/kgdw. The removal efficiencies of microplastics in the three WWTPs ranged from 76.2% to 91.2%. The primary components of microplastics were generally identified as fibers ranging in size from 10 to 100 μm. The samples collectively exhibited a total of seven distinct colors, with the predominant proportion being transparent. Polypropylene was the polymer type with the highest proportion. The sludge in WWTPs plays a pivotal role in the accumulation of MPs from wastewater bodies, necessitating increased attention toward its proper disposal in future endeavors. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive study on the redesign of a dewatering process in a polymer sludge wastewater treatment plant. The study focuses on addressing the challenges posed by high levels of organic pollutants in the sludge, with the aim of enhancing dewaterability, reducing odors, and minimizing suspended solids. Initially, a vacuum belt filter was utilized, but it proved inadequate in removing sufficient water, resulting in substantial annual disposal costs. To address this issue, a filter press system was proposed, which significantly improved the dewatering process, producing a dryer cake with a solid content of 35%, compared to 19% achieved by the vacuum belt filter. Performance evaluation of the processes was conducted based on concentration of solids and capture efficiency, demonstrating the superiority of the filter press method. Furthermore, the filtrate obtained through the filter press met local discharge regulations, eliminating the need for additional treatment before disposal. The implementation of the filter press not only improved the dewatering process and ensured compliance with discharge standards but also resulted in substantial cost savings of up to 50% per year. The payback period for the current system was determined to be 1.5 years, highlighting the economic advantages of the filter press. Overall, the findings of this study emphasize the practical advantages of the filter press in handling sludge cakes and filtrate for disposal, making it a favorable choice for dewatering polymer sludge and other wastewater treatment plants. [ABSTRACT FROM AUTHOR]

Background: Wastewater treatment plant outlets are a major source of microplastics, with more than 90% retained in sewage sludge. No standardised method for the extraction, quantification, and characterisation of microplastics in sewage sludge or soil exists, and direct comparison of studies is often impossible. Our aim was to validate oil extraction efficiency with and without pre-treatment with Fenton's reagent of selected microplastics in various types of environmental samples (sewage sludge and organic-rich substrates). Results: Oxidation with Fenton's reagent removed up to 90% of organic material, which improves the recovery rate and made quantification and characterisation easier and more reliable, regardless of type, shape, size, or density of the selected microplastic particles used in this study. Pre-treatment, as a pre-step of the oil extraction method, was shown to be important in reducing organic matter in all environmental samples, including sewage sludge and organic-rich substrates. It also improved the reliability of the selected method, shortened its duration, and, by reducing organic matter, made extracted microplastics more visible. The recovery rate was better for particles 1–5 mm and lower for particles 0.1 < 1 mm. Conclusions: By achieving up to a 100% recovery rate for certain types of microplastics (polypropylene and polystyrene), the selected method proved to be a promising extraction method. It was also shown to be efficient in the organic-rich substrates, for which the characterisation of microplastic particles was done by Fourier transform infrared spectroscopy. The most commonly detected types of microplastics in organic-rich substrates were polyethylene, polypropylene, polystyrene and polyester. [ABSTRACT FROM AUTHOR]

Pyrolysis is one method for treating sewage sludge, particularly in remote areas or decentralised systems. The end product of pyrolysis, sludge-char, can serve as a soil improver. However, there is a lack of comprehensive data on the organic pollutants' behaviour in sludge-char. In our work, we focused on the behaviour of per- and polyfluoroalkyl substances (PFASs). Sludge was pyrolyzed at 200–700 °C to determine the minimum safe temperature for effective PFASs removal. It is important to note that PFASs may not only be mineralized but also cleaved to unanalyzed PFASs and other organofluorinated substances. To address this issue, we incorporated additional measurements of organic fluorine in the experiment using combustion ion chromatography (CIC). Due to the inherent heterogeneity of sludge, containing a variety of pollutants and their precursors, we conducted pyrolysis on artificially contaminated sand. This allowed us to assess and compare the behaviour of PFASs in a homogeneous matrix. Based on our analyses, we determined that a temperature greater than 400 °C is imperative for effective PFASs and organic fluorine removal. The results were verified by analyzing samples from a commercial sludge pyrolysis unit at the Bohuslavice-Trutnov WWTP, which confirmed our measurements. In light of these results, it becomes evident that sludge pyrolysis below 400 °C is unsuitable for PFAS removal from sewage sludge. Highlights: The minimum temperature for significant PFASs and organic fluorine removal was 400 °C. PFASs were part of primary pyrolysis gas: purification or combustion is necessary. Contamination by PFASs and their congeners could be monitored with organic fluorine. [ABSTRACT FROM AUTHOR]

[Display omitted] • The effect of thermal hydrolysis on sludge hydrochar properties was investigated. • The nitrogen and sulfur content in hydrochars decreased significantly. • Hydrochar thermal decomposition stability was improved. • The driving mechanism of thermal hydrolysis was elucidated. Hydrothermal carbonization of waste activated sludge suffers from a low degree of carbonization caused by limited hydrolysis of carbohydrates and proteins, resulting in a high nitrogen content in hydrochar. Thus, it is hypothesized that thermal hydrolysis could destroy the stable floc structure of waste activated sludge, leading to higher degree of carbonization and high quality hydrochar with low nitrogen content by improving the solubilization and hydrolysis of organic matter. In the current study, thermal hydrolysis at 90 °C, 125 °C, and 155 °C was performed prior to hydrothermal carbonization to obtain low-nitrogen-content hydrochar. Thermal hydrolysis greatly improved the hydrolysis of sewage sludge. The nitrogen and sulfur content in hydrochars obtained after thermal hydrolysis decreased to 1.5–1.6 % from 1.7 %, and to 0.4 % from 0.5 %, respectively, depending on the hydrolysis conditions. Thermal decomposition stability of hydrochars obtained after thermal hydrolysis were also improved. Thermal hydrolysis at 90 °C and 125 °C promoted hydrolysis, dehydration, and the Diels-Alder reaction during hydrothermal carbonization, resulting in lower hydrochar yield but higher H/C and O/C atomic ratio. The Maillard reaction occurred during thermal hydrolysis at 155 °C, leading to the formation of large molecular refractory compounds that were retained in the hydrochar and increased the hydrochar yield. Furthermore, thermal hydrolysis can accelerate pyrolysis reaction of hydrochars, resulting in reduced energy consumption. The newly established thermal hydrolysis-hydrothermal carbonization process using sewage sludge as the feedstock has the potential to contribute to the development of the hydrothermal carbonization industry. [ABSTRACT FROM AUTHOR]

• Directions for future research of sustainable use of biosolids as a N source. • Global biosolids regulations and common biosolids treatment methods are discussed. • Higher total N content in HDB and reduced N availability from CB are reported. • Key factors in biosolids treatment affecting biosolids properties are identified. • Existing models of soil N dynamics after biosolids application are summarized. Application of biosolids to agricultural land has gained increasing attention due to their rich nutrient content. There are a variety of treatment processes for converting sewage sludge to biosolids. Different treatment processes can change the physicochemical properties of the raw sewage sludge and affect the dynamics of nutrient release in biosolids-amended soils. This paper reviews heat drying, alkaline treatment, and composting as biosolids treatment processes and discusses the effects of these treatments on biosolid nitrogen (N) content and availability. Most N in the biosolids remain in organic forms, regardless of biosolids treatment type but considerable variation exists in the mean values of total N and mineralizable N across different types of biosolids. The highest mean total N content was recorded in heat-dried biosolids (HDB) (4.92%), followed by composted biosolids (CB) (2.25%) and alkaline-treated biosolids (ATB) (2.14%). The mean mineralizable N value was similar between HDB and ATB, with a broader range of mineralizable N in ATB. The lowest N availability was observed in CB. Although many models have been extensively studied for predicting potential N mineralization in soils amended with organic amendments, limited research has attempted to model soil N mineralization following biosolids application. With biosolids being a popular, economical, and eco-friendly alternative to chemical N-fertilizers, understanding biosolids treatment effects on biosolids properties is important for developing a sound biosolids management system. Moreover, modeling N mineralization in biosolids-amended soils is essential for the adoption of sustainable farming practices that maximize the agronomic value of all types of biosolids. [ABSTRACT FROM AUTHOR]

The continuous tightening of legislation regulating the agricultural usage of sewage sludge in the province of Catalonia (Spain) leads us to propose its gasification to produce hydrogen-rich syngas. A thermodynamic equilibrium model was developed using Aspen Plus® to simulate the air and steam gasification of sewage sludge from a wastewater treatment plant in Catalonia. The syngas generated is analyzed in terms of composition and lower heating value (LHV), as a function of equivalence ratio (ER), gasification temperature (Tgas), steam-to-biomass ratio (SBR), and moisture content (MC). Results show that air-blown gasification finds the highest LHV of 7.48 MJ/m3 at 1200 °C, ER of 0.2, and MC of 5%. Using steam as the gasifying agent, an LHV of 10.30 MJ/m3 is obtained at SBR of 0.2, MC of 5%, and 1200 °C. A maximum of 69.7% hydrogen molar fraction is obtained at 600 °C, MC of 25%, and SBR of 1.2. This study suggests using steam as a gasifying agent instead of air since it provides a higher LHV of the syngas as well as a hydrogen-richer syngas for the implementation of gasification as an alternative method to sewage sludge treatment in the region of Catalonia. Since the economic aspect should also be considered, in this regard, our sensitivity analysis provided important data demonstrating that it is possible to reduce the gasification temperature without significantly decreasing the LHV. [ABSTRACT FROM AUTHOR]

The aim of the present work was to investigate ash formation and associated interactions during the pulverized fuel co-combustion of biomass fuels. Combustion experiments were carried out with narrowly sized wheat straw (WS), sewage sludge (SS), and their blends in a drop tube furnace at 1100 °C and 1300 °C. The resulting residual ash and fine particulate matter (PM10) were characterized with various analyses. It was observed that co-combustion influences size distributions of the residual ash particles and generally generates larger residual ash particles close to those of SS combustion. The interaction of K capture by minerals enhances the melting and consequently increases the production of large and melting ash particles during co-combustion. It was found that blending SS with WS has not only the positive interaction of K capture by minerals from SS ash to significantly reduce submicron ash formation, but also the positive interaction of transforming alkali chlorides into alkali sulfates to reduce the corrosiveness of submicron ash particles. Co-combustion of SS with WS can also reduce the presence of alkali chloride at PM1–10, lowering the propensities of deposition and corrosion of the fine residual ash particles. [ABSTRACT FROM AUTHOR]

The valorisation of sewage sludge for sustainable agricultural use and biofuel production proposes an effective and beneficial management of sewage sludge in a closed-loop cycle. The management of sewage sludge biowaste is a rising problem due to increasing waste storage expenses. In this sense, the use of circular economy principles in sewage sludge management creates opportunities to develop new technologies for processing. The biorefinery model allows the application of wasteless technologies via sewage sludge valorisation in terms of agricultural use and biofuel production, especially with the hydrothermal carbonisation method. Applying hydrothermal carbonisation in the treatment of biosolid sewage sludge has numerous benefits due to processing highly hydrated organic waste into carbon hydro char, a high-quality solid biofuel. The direct use of sewage sludge in the soil does not allow for full use of its functional properties. However, the hydrothermal carbonisation of sewage sludge results in biocarbon pellets, making it a viable approach. This work also discusses the barriers (legal, chemical, biological, and technical) and possibilities related to sewage sludge biorefining processes. [ABSTRACT FROM AUTHOR]

Utilizing waste, such as sewage sludge, into biochar fits the circular economy concept. It maximizes the reuse and recycling of waste materials in the wastewater treatment plant. The experiments were conducted to assess: (1) the impact of the temperature on the properties of biochar from sewage sludge (400 °C, 500 °C, 600 °C, 700 °C); (2) how the physical activation (CO2, hot water) or chemical modification using (MgCl2, KOH) could affect the removal of ammonia nitrogen and phosphorus from filtrate collected from sludge dewatering filter belts or synthetic solution, wherein the concentration of ammonium nitrogen and phosphorus were similar to the filtrate. Based on the Brunner–Emmett–Teller (BET) surface and the type and concentration of surface functional groups for the second stage, biochar was selected and produced at 500 °C. The modification of biochar had a statistically significant effect on removing nitrogen and phosphorus from the media. The best results were obtained for biochar modified with potassium hydroxide. For this trial, 15%/17% (filtrate/synthetic model solution) and 72%/86% nitrogen and phosphorus removal, respectively, were achieved. [ABSTRACT FROM AUTHOR]

Soil application of treated sewage sludge is considered a beneficial management option for agriculture and environment. Sludge treated with clay minerals or biochar was evaluated as soil amendment, in comparison with limed or untreated sludge. Bentonite, vermiculite, biochar or lime was added to dewatered sewage sludge at 0 and 15% rates, in three replications and air-dried. Then, the treated and untreated sludge were added to two soils, one acid and one alkaline, at 0 (control), 1 and 3% rates, in three replications. The results showed that the pH of acid soil significantly increased compared to control upon addition of treated and untreated sludge at both rates, but remained acidic (<6.0) in all cases except for limed sludge. Upon addition of 3% treated or untreated sludge to both soils, organic carbon (OC) significantly increased compared to control. The same stands for soil available ammonium nitrogen (NH4-N), phosphorus (P), potassium (K), copper (Cu), zinc (Zn) and boron (B) for both soils and rates. Soil total heavy metals, which regulate sludge's agronomic use, were below the legislative limits. However, the 3% addition rate of all kinds of sludge, especially of untreated, to both soils increased the electrical conductivity of saturation extract (ECse >2 dS m−1) at unacceptable levels for sensitive crops and available P, B and Zn 2–3, 2–4 and 6–12 times above the initial, respectively. Consequently, sewage sludge treated with bentonite, vermiculite or biochar could be used as a soil amendment but at rates lower than 3% (≈120 Mg ha−1). [ABSTRACT FROM AUTHOR]

Wastewater treatment plants (WWTPs) are considered to be hotspots for the spread of antibiotic resistance genes (ARGs). We performed a metagenomic analysis of the raw wastewater, activated sludge and treated wastewater from two large WWTPs responsible for the treatment of urban wastewater in Moscow, Russia. In untreated wastewater, several hundred ARGs that could confer resistance to most commonly used classes of antibiotics were found. WWTPs employed a nitrification/denitrification or an anaerobic/anoxic/oxic process and enabled efficient removal of organic matter, nitrogen and phosphorus, as well as fecal microbiota. The resistome constituted about 0.05% of the whole metagenome, and after water treatment its share decreased by 3–4 times. The resistomes were dominated by ARGs encoding resistance to beta-lactams, macrolides, aminoglycosides, tetracyclines, quaternary ammonium compounds, and sulfonamides. ARGs for macrolides and tetracyclines were removed more efficiently than beta-lactamases, especially ampC, the most abundant ARG in the treated effluent. The removal efficiency of particular ARGs was impacted by the treatment technology. Metagenome-assembled genomes of multidrug-resistant strains were assembled both for the influent and the treated effluent. Ccomparison of resistomes from WWTPs in Moscow and around the world suggested that the abundance and content of ARGs depend on social, economic, medical, and environmental factors. [ABSTRACT FROM AUTHOR]

The land application of sewage sludge can cause different environmental problems due to the high content of potentially toxic elements (PTEs). The objective of this study was to compare the effect of urban biological sewage sludge (i.e. the waste of activated sludge process) and its derived biochar as the soil amendments on the bioavailability of PTEs and their bioaccumulation by corn (Zea mays L.) under two months of greenhouse conditions. The soil was treated by adding biochar samples at 0 (control), 1, 3, 5% w/w. The diethylenetriamine pentaacetic acid (DTPA)-extractable concentrations of PTEs including Zn, Pb, Cd, Cr, Ni, Fe, and Cu in soil and their accumulation by plant shoot and root were measured. Conversion of the biological sewage sludge into the biochar led to decrease the PTEs bioavailability and consequently decreased their contents in plant tissues. The DTPA extractable metal concentrations of produced biochar in comparison to the biological sewage sludge reduced 75% (Cd), 65% (Cr), 79% (Ni and Pb), 76% (Zn), 91% (Cu) and 88% (Fe). Therefore, the content of Ni, Fe, Zn and Cd in corn shoot was decreased 61, 32, 18 and 17% respectively in application of 5% biochar than of raw sewage sludge. Furthermore, the application of 5% biochar enhanced the physiological parameters of the plants including shoot dry weight (twice) and wet weight (2.25 times), stem diameter (1.70 times), chlorophyll content (1.03 times) in comparison to using 5% raw sewage sludge. The results of the study highlight that application of the biochar derived from urban biological sewage sludge in soil could decrease the risk of PTEs to the plant. [ABSTRACT FROM AUTHOR]

Background: Massive amounts of sewage sludge are generated during biological sewage treatment and are commonly subjected to anaerobic digestion, land application, and landfill disposal. Concurrently, persistent organic pollutants (POPs) are frequently found in sludge treatment and disposal systems, posing significant risks to both human health and wildlife. Metabolically versatile microorganisms originating from sewage sludge are inevitably introduced to sludge treatment and disposal systems, potentially affecting the fate of POPs. However, there is currently a dearth of comprehensive assessments regarding the capability of sewage sludge microbiota from geographically disparate regions to attenuate POPs and the underpinning microbiomes. Results: Here we report the global prevalence of organohalide-respiring bacteria (OHRB) known for their capacity to attenuate POPs in sewage sludge, with an occurrence frequency of ~50% in the investigated samples (605 of 1186). Subsequent laboratory tests revealed microbial reductive dechlorination of polychlorinated biphenyls (PCBs), one of the most notorious categories of POPs, in 80 out of 84 sludge microcosms via various pathways. Most chlorines were removed from the para- and meta-positions of PCBs; nevertheless, ortho-dechlorination of PCBs also occurred widely, although to lower extents. Abundances of several well-characterized OHRB genera (Dehalococcoides, Dehalogenimonas, and Dehalobacter) and uncultivated Dehalococcoidia lineages increased during incubation and were positively correlated with PCB dechlorination, suggesting their involvement in dechlorinating PCBs. The previously identified PCB reductive dehalogenase (RDase) genes pcbA4 and pcbA5 tended to coexist in most sludge microcosms, but the low ratios of these RDase genes to OHRB abundance also indicated the existence of currently undescribed RDases in sewage sludge. Microbial community analyses revealed a positive correlation between biodiversity and PCB dechlorination activity although there was an apparent threshold of community co-occurrence network complexity beyond which dechlorination activity decreased. Conclusions: Our findings that sludge microbiota exhibited nearly ubiquitous dechlorination of PCBs indicate widespread and nonnegligible impacts of sludge microbiota on the fate of POPs in sludge treatment and disposal systems. The existence of diverse OHRB also suggests sewage sludge as an alternative source to obtain POP-attenuating consortia and calls for further exploration of OHRB populations in sewage sludge. 7vWBgxzBnCPA6QWxMbshMg Video Abstract [ABSTRACT FROM AUTHOR]

The objectives of this study were to evaluate sewage sludge's stabilization with untested until now materials, such as selective clay minerals or biochar in comparison with liming, for enhancing sludge's fertilization capacity. Dewatered sewage sludge was mixed with bentonite, vermiculite, zeolite, biochar or lime at rates of 0, 15 and 30%, air-dried and analyzed for pathogens and chemical properties. Almost all fecal indicators of treated sludge with 15% bentonite, vermiculite or biochar were reduced by at least one-logarithmic unit (log10) (indicative value of sludge's stabilization), whereas those of limed sludge were undetectable. Electrical conductivity of all treatments significantly increased, and the highest values were obtained for untreated (6.1 dS m−1) and limed sludge (above 7.0 dS m−1 for both addition rates). The untreated sludge had the significantly highest water-soluble ammonium-nitrogen (2817 mg kg−1) and phosphorus (263 mg kg−1) concentrations followed by sludge treated with bentonite, vermiculite or biochar, whereas limed sludge had the lowest content. Boron concentration of the untreated sludge was similar to the treated sludge. Total concentrations of heavy metals were far below the legislative permissible levels for sludge's agronomic use. Nutrients' total content of treated sludge ranged at levels of similar magnitude to the untreated sludge, except for certain cases where they were increased because of the materials' composition. Consequently, sewage sludge treated with 15% bentonite, vermiculite or biochar seems to be stabilized, retain bioavailable nitrogen and serve as a fertilizer of macro- and micronutrients. However, potential risks of agronomic use, i.e., soil salinization and boron phytotoxicity, should be considered. [ABSTRACT FROM AUTHOR]

Due to the limitations of conventional ultrafiltration/microfiltration-based membrane bioreactors (UF/MF-MBRs) in removing trace organic compounds (TrOCs), the concept of high-retention membrane bioreactors (HR-MBRs) was introduced. Despite the benefits, HR-MBRs still suffer several drawbacks. Therefore, this paper critically reviews the effectiveness and feasibility of the proposed strategies to alleviate fouling, salinity build-up and incomplete biodegradation of TrOCs during wastewater treatment by HR-MBRs. The severity of each challenge is compared amongst the various configurations together with the associated capital and operational expenditure to determine the most cost-effective set-up. Guidance is provided on strategies and/or lessons that could be adopted from well-established processes used at municipal scale. Chemical cleaning as mitigation for fouling degrades membranes leading to poor TrOCs removal, while pre-treatment and membrane surface modification increase operational expenditure (OpEX). However, there are other environmentally-friendly pretreatment and cleaning options which hold great potential for future application. These options such as advanced oxidation processes (AOPs) are critically discussed in this work. Further, in-depth discussion is made on the pros and cons of the various approaches (such as frequent sludge withdrawal, intermittent UF/MF filtration and using organic salts) to alleviate salt build-up. Finally, incomplete biodegradation of rejected TrOCs in the bioreactor transfers problems of toxic pollutants from wastewater treatment to sludge management. Herein mitigation strategies including using stronger biological agents and coupling HR-MBRs with other techniques are debated. Despite the challenges, HR-MBRs are a promising solution for clean water production from TrOCs impaired wastewater. Therefore, more research is needed to improve the performance of HR-MBRs. [ABSTRACT FROM AUTHOR]

To date, only a few studies focused on the carbon monoxide (CO) production during waste composting; all targeted on CO inside piles. Here, the CO net emissions from compost piles and the assessment of worker's occupational risk of exposure to CO at large-scale composting plants are shown for the first time. CO net emissions were measured at two plants processing green waste, sewage sludge, or undersize fraction of municipal solid waste. Effects of the location of piles (hermetised hall vs. open yard) and turning (before vs. after) were studied. Higher CO net emission rates were observed from piles located in a closed hall. The average CO flux before turning was 23.25 and 0.60 mg‧m-2‧h-1 for hermetised and open piles, respectively, while after– 69.38 and 5.11 mg‧m-2‧h-1. The maximum CO net emissions occurred after the compost was turned (1.7x to 13.7x higher than before turning). The top sections of hermetised piles had greater CO emissions compared to sides. Additionally, 5% of measurement points of hermetised piles switched to 'CO sinks'. The 1-h concentration in hermetised composting hall can reach max. ~50 mg CO∙m-3 before turning, and >115 mg CO∙m-3 after, exceeding the WHO thresholds for a 1-h and 15-min exposures, respectively. [ABSTRACT FROM AUTHOR]

This paper aims to study the feasibility of municipal sewage sludge utilization as an energy source in a polygeneration system. This system offers distinctive benefits such as contribution to the principled removal of sewage sludge, simultaneous utilization of raw and digested sludge in different parts of the system, and production of renewable hydrogen from bio-waste. 4E (energy, exergy, exergoeconomic, and environmental) analyses, are performed to understand the system performance comprehensively. Then, parametric studies are examined the impact of changing the values of main parameters on the system operation. Afterward, a multi-objective optimization based on a genetic algorithm is carried out to achieve optimal values, considering a trade-off between the exergy efficiency and the total cost rate. Meanwhile, this work harnesses the potential of artificial neural networks to expedite complex and time-consuming optimization processes. According to the results, the gasifier exhibits the highest rate of exergy destruction, and the primary cost of consumption is attributed to its heat supply. The multi-objective optimization findings show that the optimum point has an exergy efficiency of 38.26 % and a total cost rate of 58.17 M$/year. The hydrogen production rate, energy efficiency, and net power generation rate for the optimal case are determined as 1692 kg/h, 35.24 %, and 4269 kW, respectively. Also, the unit cost of hydrogen in the optimal case is obtained 1.49 $/kg which offers a cost-effective solution for hydrogen production. [Display omitted] • 4E analysis and optimization performed on a bio-waste driven polygeneration system. • Plant optimized using artificial neural network and multi-objective genetic algorithm. • The feasibility of integrating a membrane for hydrogen separation investigated. • The optimum exergy efficiency and total cost rate obtained 38.26 % and 58.17 M$/year. • Hydrogen and electricity cost of 1.49 $/kg and 0.0145 $/kWh achieved for optimal case. [ABSTRACT FROM AUTHOR]