Search

Electroplated diamond tools with single-layered high density diamond particles in an average size of 150 μm were prepared through a three-step electroplating process, including Ni-undercoating, Ni-diamond co-electrodeposition, and Cr-C strengthening electroplating. Martensitic stainless steel (AISI 440C) rods with a diameter of 3 mm were used as substrates for tool fabrications. To evaluate tool grinding performances, linear slot grinding tests on the Al2O3 plates were conducted. The grinding performance of an electroplated diamond tool was determined through its maximum ground length upon tool failure. Experimental results show that an electroplated diamond tool with high density of diamond particles can be prepared by using Ni-diamond co-electrodeposition. After annealing at 500 °C for 30 min, the hardness of Cr-C deposit was significantly increased from 597 to 1636 Hv. The anneal-hardened Cr-C deposit is a suitable strengthening layer for fabricating electroplated diamond tools. The grinding performance of an electroplated diamond tool was strongly affected by the Ni-undercoating thickness. The highest maximum ground length of 2231 mm can be achieved by the electroplated diamond tool with a Ni-undercoating thickness of 90 μm. When the Cr-C strengthening deposit wore out, extruded diamond particles on the tool surface could be easily embedded into the Ni-undercoating, leading to fatigue fracture of the AISI 440C substrate. [ABSTRACT FROM AUTHOR]

Nowadays, minimal invasive surgery (MIS) plays an important role in the treatment of infectious spondylitis. This paper reviews the current options in MIS techniques and discusses the surgical outcomes from a series of cases at our department. Demographic characteristics and pre-operative clinical status of 21 patients with MIS for multilevel infectious spondylitis were analyzed; also, pre- and post-operative X-rays were assessed for surgical correction angles and fusion status. The results indicated that percutaneous endoscopic debridement (PEDD) and drainage has the advantages of less blood loss and shorter recovery time. Overall, percutaneous screw system can preserve paravertebral soft tissue, reduce post-operative pain, and foster early post-operative mobilization. Robot-assisted percutaneous screw placement is more accurate than using free-hand. Cortical bone trajectory (CBT) screw requires less surgical exposure while preserving adequate strength. Endoscopic lumbar interbody fusion (Endo-LIF) is an alternative fusion technique to treat spondylitis because it offers better functional prognosis than minimally invasive transforaminal lumbar interbody fusion (MIS-TLIF) in the treatment of degenerative lumbar diseases. All the enrolled patients via MIS-TLIF obtained good surgical outcomes. Various minimally invasive techniques have been evolved and modified, so it is important for spine surgeon to keep up to date with advanced orthopedic knowledge and surgical techniques. [ABSTRACT FROM AUTHOR]

Background: Thoracic ossification of the ligamentum flavum (TOLF), a rare condition more prevalent in East Asia, is managed through open and endoscopic surgical approaches. Determining the superior surgical option remains unclear. This study assesses the safety and clinical outcomes associated with these approaches in TOLF patients.Following Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines, we conducted a systematic literature search up to August 5, 2023, across PubMed, Scopus, EMBASE, Web of Science, Cochrane, and ClinicalTrials.gov. We included randomized controlled trials and cohort studies reporting complication rates, mJOA (modified Japanese Orthopedic Association) scores, JOA scores, VAS (Visual Analog Scale) scores, or hospitalization duration for both open and endoscopic surgeries in TOLF patients.We analyzed 37 studies encompassing 1,646 TOLF patients using a random-effects model. Our findings revealed a significant difference in complication rates (overall complication rates: 0.12; 95% CI: 0.07, 0.19; p < 0.01; I2: 69%; quality of evidence: moderate), with lower complication rates in the endoscopy group. However, no significant differences were observed in JOA scores (overall JOA: 8.35; 95% CI: 7.16, 9.54; p = 0.12; I2: 99%; quality of evidence: very low), VAS scores (overall VAS: 1.31; 95% CI: 1.03, 1.59; p = 0.35; I2: 91%; quality of evidence: very low), or hospitalization duration (hospital stay: 10.83 days; 95% CI: 6.86, 14.80; p = 0.35; I2: 91%; quality of evidence: very low) between the open and endoscopic groups.This meta-analysis reports lower complication rates and improved postoperative mJOA scores for endoscopic surgery in TOLF patients compared to open surgery. It represents the first comprehensive evaluation of clinical outcomes and safety of different surgical approaches for TOLF patients. Further randomized controlled trials are essential to validate these findings.Methods: Thoracic ossification of the ligamentum flavum (TOLF), a rare condition more prevalent in East Asia, is managed through open and endoscopic surgical approaches. Determining the superior surgical option remains unclear. This study assesses the safety and clinical outcomes associated with these approaches in TOLF patients.Following Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines, we conducted a systematic literature search up to August 5, 2023, across PubMed, Scopus, EMBASE, Web of Science, Cochrane, and ClinicalTrials.gov. We included randomized controlled trials and cohort studies reporting complication rates, mJOA (modified Japanese Orthopedic Association) scores, JOA scores, VAS (Visual Analog Scale) scores, or hospitalization duration for both open and endoscopic surgeries in TOLF patients.We analyzed 37 studies encompassing 1,646 TOLF patients using a random-effects model. Our findings revealed a significant difference in complication rates (overall complication rates: 0.12; 95% CI: 0.07, 0.19; p < 0.01; I2: 69%; quality of evidence: moderate), with lower complication rates in the endoscopy group. However, no significant differences were observed in JOA scores (overall JOA: 8.35; 95% CI: 7.16, 9.54; p = 0.12; I2: 99%; quality of evidence: very low), VAS scores (overall VAS: 1.31; 95% CI: 1.03, 1.59; p = 0.35; I2: 91%; quality of evidence: very low), or hospitalization duration (hospital stay: 10.83 days; 95% CI: 6.86, 14.80; p = 0.35; I2: 91%; quality of evidence: very low) between the open and endoscopic groups.This meta-analysis reports lower complication rates and improved postoperative mJOA scores for endoscopic surgery in TOLF patients compared to open surgery. It represents the first comprehensive evaluation of clinical outcomes and safety of different surgical approaches for TOLF patients. Further randomized controlled trials are essential to validate these findings.Results: Thoracic ossification of the ligamentum flavum (TOLF), a rare condition more prevalent in East Asia, is managed through open and endoscopic surgical approaches. Determining the superior surgical option remains unclear. This study assesses the safety and clinical outcomes associated with these approaches in TOLF patients.Following Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines, we conducted a systematic literature search up to August 5, 2023, across PubMed, Scopus, EMBASE, Web of Science, Cochrane, and ClinicalTrials.gov. We included randomized controlled trials and cohort studies reporting complication rates, mJOA (modified Japanese Orthopedic Association) scores, JOA scores, VAS (Visual Analog Scale) scores, or hospitalization duration for both open and endoscopic surgeries in TOLF patients.We analyzed 37 studies encompassing 1,646 TOLF patients using a random-effects model. Our findings revealed a significant difference in complication rates (overall complication rates: 0.12; 95% CI: 0.07, 0.19; p < 0.01; I2: 69%; quality of evidence: moderate), with lower complication rates in the endoscopy group. However, no significant differences were observed in JOA scores (overall JOA: 8.35; 95% CI: 7.16, 9.54; p = 0.12; I2: 99%; quality of evidence: very low), VAS scores (overall VAS: 1.31; 95% CI: 1.03, 1.59; p = 0.35; I2: 91%; quality of evidence: very low), or hospitalization duration (hospital stay: 10.83 days; 95% CI: 6.86, 14.80; p = 0.35; I2: 91%; quality of evidence: very low) between the open and endoscopic groups.This meta-analysis reports lower complication rates and improved postoperative mJOA scores for endoscopic surgery in TOLF patients compared to open surgery. It represents the first comprehensive evaluation of clinical outcomes and safety of different surgical approaches for TOLF patients. Further randomized controlled trials are essential to validate these findings.Conclusions: Thoracic ossification of the ligamentum flavum (TOLF), a rare condition more prevalent in East Asia, is managed through open and endoscopic surgical approaches. Determining the superior surgical option remains unclear. This study assesses the safety and clinical outcomes associated with these approaches in TOLF patients.Following Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines, we conducted a systematic literature search up to August 5, 2023, across PubMed, Scopus, EMBASE, Web of Science, Cochrane, and ClinicalTrials.gov. We included randomized controlled trials and cohort studies reporting complication rates, mJOA (modified Japanese Orthopedic Association) scores, JOA scores, VAS (Visual Analog Scale) scores, or hospitalization duration for both open and endoscopic surgeries in TOLF patients.We analyzed 37 studies encompassing 1,646 TOLF patients using a random-effects model. Our findings revealed a significant difference in complication rates (overall complication rates: 0.12; 95% CI: 0.07, 0.19; p < 0.01; I2: 69%; quality of evidence: moderate), with lower complication rates in the endoscopy group. However, no significant differences were observed in JOA scores (overall JOA: 8.35; 95% CI: 7.16, 9.54; p = 0.12; I2: 99%; quality of evidence: very low), VAS scores (overall VAS: 1.31; 95% CI: 1.03, 1.59; p = 0.35; I2: 91%; quality of evidence: very low), or hospitalization duration (hospital stay: 10.83 days; 95% CI: 6.86, 14.80; p = 0.35; I2: 91%; quality of evidence: very low) between the open and endoscopic groups.This meta-analysis reports lower complication rates and improved postoperative mJOA scores for endoscopic surgery in TOLF patients compared to open surgery. It represents the first comprehensive evaluation of clinical outcomes and safety of different surgical approaches for TOLF patients. Further randomized controlled trials are essential to validate these findings. [ABSTRACT FROM AUTHOR]

Background Context: As science and technology have advanced, novel bone cements with numerous formulated ingredients have greatly evolved and been commercialized for vertebroplasty. Recently, viscosity has been a focus to achieve better clinical outcomes and fewer complications. Meanwhile, the experience in the treatment of mid (T7-9) to high (T4-6) thoracic vertebral compression fractures is limited.Purpose: The objective of this study was to identify the different outcomes between high-viscosity bone cement (HVBC) and low-viscosity bone cement (LVBC) used to repair mid (T7-9)- and high (T4-6)- thoracic vertebral compression fractures.Study Design/setting: This study was a single-center, retrospective cohort study PATIENT SAMPLE: A consecutive series of 107 patients with a total of 144 vertebrae was included.Outcome Measures: The anterior vertebral height (AVH), middle vertebral height (MVH), posterior vertebral height (PVH), local kyphotic angle (KA), Cobb angle (CA), and other associated parameters were evaluated radiologically at several time points-preoperative, surgery day 0, postoperative day 1, and 6-month follow-up. Pain evaluation was assessed by using a visual analog scale (VAS) before and 6 months after the procedure.Methods: The patients were divided into two groups according to the viscosity of the bone cement used, and plain film and magnetic resonance imaging (MRI) of the vertebrae were used to calculate parameters. The patient characteristics; bone cement brand; changes in AVH, MVH, PVH, KA, CA, and VAS; and complications of each patient were recorded and then analyzed.Results: Both groups showed increased vertebral body height, corrected KA, and CA after vertebroplasty. There were no significant differences between the HVBC and LVBC groups (ΔAVH: 2.19±2.60 vs. 2.48±3.09, p=.555; ΔMVH: 1.25±3.15 vs. 1.89±2.58, p=.192; ΔKA: -5.46±4.58 vs -5.37±4.47, p=.908; and ΔCA: -4.22±4.23 vs. -4.56±5.17, p=.679). There were significant preoperative to postoperative and preoperative to follow-up changes in AVH (HVBC, p=.012 and .046, respectively; LVBC, p=.001 and .015, respectively); a significant preoperative to postoperative change in MVH (HVBC, p=.045; LVBC, p=.001); and significant preoperative to postoperative and preoperative to follow-up changes in KA and CA (KA: HVBC, p=0.000 and .003, respectively; LVBC, p=.000 and .000, respectively; CA: HVBC, p=.017 and .047, respectively; LVBC, p=.006 and .034, respectively). The volume of cement injected was significantly higher with HVBC (3.66±1.36 vs. 3.11±1.53, p=.024), and the use of HVBC was associated fewer cases with cement leakage (26 vs. 45, p=.002). Furthermore, there was no difference between the groups in the incidence of adjacent fracture. Both groups showed an improved VAS score at follow-up, with statistically greater improvement in the HVBC group (2.40±1.53 vs. 3.07±1.69, p=.014). Moreover, significantly fewer patients with a VAS score ≥ 3 were found in the HVBC group (22 vs. 39, p=.004) CONCLUSIONS: HVBC and LVBC are safe and effective to treat mid-to-high level thoracic vertebral compression fractures. Compared with LVBC, HVBC shows less cement leakage, a greater injection volume, and better postoperative pain relief. [ABSTRACT FROM AUTHOR]

The elderly population has an increased risk of degenerative cervical myelopathy due to multilevel disease, causing motor and sensory dysfunctions and a poor quality of life. Multilevel anterior cervical discectomy and fusion (ACDF) is an alternative surgical treatment option, but has a perceived higher risk of complications. The goal of this study is to report the outcome. We retrospectively reviewed patients from 2006 to 2019 undergoing multilevel ACDF for degenerative cervical myelopathy and compared outcomes and complications between elder patients (aged 70 and above) and younger patients (below 70). The patients' comorbidities, and postoperative complications, radiographic parameters such as C2–C7 Cobb angle, C2–C7 sagittal vertical axis, inter-body height of surgical levels and fusion rate were recorded. Japanese Orthopaedic Association (JOA) score and modified Odom's score were collected. Included were 18 elderly (mean age 74, range 70–87) and 45 young patients (mean age 56, range 43–65) with a follow-up of 43.8 and 55.5 months respectively. Three-level ACDF was the most common. The ratios of ASA class III patients were 94.4% and 48.9% (p < 0.001). The Charlson comorbidity indexes were 4.3 ± 1.03 and 2.1 ± 1.11 (p < 0.001). The average lengths of hospital stays were 4.9 and 4.6 days. Eleven patients (61.1%) in the elderly group experienced at least one short-term complication, compared with 16 patients (35.6%) in the younger group (p < 0.05). The middle-term complications were comparable (22.2% and 20.0%). The JOA score, recovery rate and modified Odom score showed comparable result between groups. Despite its extensiveness, multilevel ACDF is feasible for the elder patients with good clinical outcome and fusion rate. When compared to younger cohort, there is a trend of lower preoperative JOA score and recovery rate. The short-term complication rate is higher in the elderly group. [ABSTRACT FROM AUTHOR]

Polymethylmethacrylate (PMMA) has been applied clinically and biomechanically repair loose pedicle screws. Controversies have arisen over data due to uncontrolled cement properties, various locations and sizes of fenestrated holes in repair screws, irregular holes and different bone densities of specimens. In this study, the pullout strength was compared for two techniques, the modified technique to use PMMA to augment a threaded hole and the traditional technique with retrograde injection of a PMMA filling, for standard loose screws in porcine vertebrae. Both techniques provided statistically significant results for sufficiently randomized specimens and experimental procedures. The difference in the pullout strength between conical and cylindrical screws for the aforementioned cement augmentation techniques was also investigated. Twenty-four single-level fresh-frozen lumbar vertebrae from L1 to L6 were harvested from four mature pigs. A total of 0.8 ml of PMMA was retrograde injected into screw holes with a 5.5 mm diameter, followed by insertion of a 5.0 mm diameter repair screw in the traditional group (n = 12). A stiff threaded PMMA hole was created with a 4.5 mm tapping screw before insertion of repair screws in the modified group (n = 12). Two screw geometries were randomly assigned as cylindrical (n = 6) and conical (n = 6) in each group. The correlations between filling techniques, screw geometries and axial pullout strength were analyzed. An appropriate screw trajectory and insertion depth were confirmed using X-ray imaging prior to pullout testing in both groups. For a given screw geometry (cylindrical or conical), the pullout force of the modified group was significantly higher than that of the traditional group. There was no significant difference in the pullout force between the screw geometries for a given filling technique. The cement augmentation technique is far more influential than the screw outer geometry. The modified PMMA technique created a greater anchor force than the traditional method and could be an alternative for revision of pedicle screw loosening. [ABSTRACT FROM AUTHOR]

Background: To determine how perforated peptic ulcers be diagnosed earlier after patients undergoing an elective spine surgery.Methods: Patients who underwent elective spine surgeries at our hospital between January 2000 and April 2018 and experienced an acute perforated peptic ulcer were included. An age-and gender-matched control group was comprised of 26 patients without a postoperative acute perforated peptic ulcer who received spine surgery during the same period. Medical records and imaging studies were thoroughly reviewed.Results: Thirteen patients were enrolled in the study group, including eight females and five males. Three patients, two females and one male, died of uncontrolled peritonitis during the hospital stay. All patients in the study group experienced the sudden onset of abdominal pain, which was continuous and progressively worsening. Patients with elevated serum amylase, a peptic ulcer history and increased intraoperative blood loss had a tendency to develop a postoperative perforated peptic ulcer.Conclusion: Spine surgeons should be highly alert to these risk factors of postoperative perforated peptic ulcers inpatients who has history of peptic ulcer, large amount ofintraoperative blood loss and abnormal high serum amylase level after elective spine surgery. Early diagnosis and emergent surgical intervention promote better outcomes. [ABSTRACT FROM AUTHOR]

Background: In cases of postoperative deep wound infection after interbody fusion with cages, it is often difficult to decide whether to preserve or remove the cages, and there is no consensus on the optimal approach for removing cages. The aim of this study was to investigate the surgical management of cage infection after lumbar interbody fusion. Methods: A retrospective study was conducted between January 2012 and August 2018. Patients were included if they had postoperative deep wound infection and required cage removal. Clinical outcomes, including operative parameters, visual analog scale, neurologic status, and fusion status, were assessed and compared between anterior and posterior approaches for cage removal. Results: Of 130 patients who developed postoperative infection and required surgical debridement, 25 (27 levels) were diagnosed with cage infection. Twelve underwent an anterior approach, while 13 underwent cage removal with a posterior approach. Significant differences were observed between the anterior and posterior approaches in elapsed time to the diagnosis of cage infection, operative time, and hospital stay. All patients had better or stationary American Spinal Injury Association impairment scale, but one case of recurrence in adjacent disc 3 months after the surgery. Conclusions: Both anterior and posterior approaches for cage removal, followed by interbody debridement and fusion with bone grafts, were feasible methods and offered promising results. An anterior approach often requires an additional extension of posterior instrumentation due to the high incidence of concurrent pedicle screw loosening. The use of an endoscope-assisted technique is suggested to facilitate safe removal of cages. [ABSTRACT FROM AUTHOR]

This work proposes an effective design of bioactive 3D-printed Ti-6Al-4V scaffold with the CaO-MgO-SiO 2 glass-ceramic coating to realize a comparable elastic modulus of bone tissue and boost osteogenic differentiation. The improved elastic modulus and stiffness of Ti alloy were achieved via effectively increasing surface area of Ti alloy to reduce stress shielding effect. A hydrophilic surface and bioactive glass-ceramic coating were conducted via chemical etching and heat-treatment under argon atmosphere to enhance cells attachment and boost cell proliferation and osteogenic differentiation. The expression of osteogenic genes in bioactive CaO-MgO-SiO 2 glass-ceramic was evaluated through ALP, OPN, Runx2, and Col1A1 gene markers to explore the mechanism of superior osteogenic differentiation. Significant increase in OPN expression level confirmed the effect of CaO-MgO-SiO 2 coating for the enhancement of osteogenic bioactivity. This work provides a feasible approach through surface etching and bioactive CaO-MgO-SiO 2 glass-ceramic coating on the Ti alloy surface to enhance bioactivity and osteogenesis. [Display omitted] • A compatible bone tissue of 3D-printed Ti-6Al-4V scaffold with the novel bioactive CaO-MgO-SiO 2 glass-ceramic coating. • A superior surface modification to enhance cells attachment and boost cell proliferation and osteogenic differentiation. • This work provides a feasible approach on the Ti-alloy surface to enhance bioactivity and osteogenesis. [ABSTRACT FROM AUTHOR]

In some cases of vertebroplasty for adjacent fractures, we observed a cement bridging phenomenon, in which the injected cement flowed from the newly fractured vertebra to the previously cement-augmented vertebra through the space between the abutting anterior longitudinal ligament and the vertebral column. The purpose of this retrospective study was to investigate this phenomenon. From January 2012 to December 2014, patients who sustained new-onset adjacent vertebral compression fracture and who were again treated with vertebroplasty were enrolled. We divided the patients into two groups, the bridging group and the nonbridging group, to analyze the difference between them. Results showed that the cement bridging phenomenon occurred in 18 (22.8%) of the 79 patients. Significant differences between the bridging and nonbridging groups were identified in the following 3 imaging features: severe loss of the anterior vertebral body height at the new-onset adjacent vertebra on plain film (odds ratio [OR] = 4.46, p = 0.014), fluid accumulation (OR = 36.27, p < 0.001) and hypointense signaling (OR = 15.67, p < 0.001) around the space anterior to the abutting vertebral bodies and the corresponding intervertebral disc on MRI. After a 2-year follow-up, both the mean value of the focal kyphotic angle and anterior body height ratio were significantly better in the cement bridging group than in the nonbridging group. The cement bridging phenomenon, which has never been reported in the literature, is not rare in clinical practice. This phenomenon was associated with better maintenance of focal kyphotic angle and anterior body height ratio during the 2-year follow-up. [ABSTRACT FROM AUTHOR]

Synthetic bone graft has gained considerable attention because of an increase in the aged population. In the present study, a biphasic bone graft composed of hydroxyapatite (HAp) and calcium sulfate (CS) is prepared using a gel-foaming technique. The gel is prepared at a temperature as low as 35 °C; many pores are introduced into the gel through an agitation process. The foamed gel can be cut into any shape and size. After sintering, the porosity of the biphasic bone graft is approximately 70%. Depending on the HAp/CS ratio, the amount of macropores and micropores can be tailored. The macropores of approximately 130 μm diameter are interconnected with each other through openings of 40 μm size. The biphasic bone graft exhibits no cytotoxicity; preosteoblast cells can adhere and proliferate on the surface of the fabricated bone graft. However, migration of these cells into the bone graft is considerably limited in the in vitro study. When the biphasic bone graft is implanted into the distal femur of rats, with the combined effect of osteoblast and osteoclast cells, more than 90% of the bone graft is degraded after 3 months. New trabeculae bone and bone marrow are observed within the bone defect. The HAp/CS composite can thus be used as degradable bone grafts. [ABSTRACT FROM AUTHOR]

In this study, the characteristics of a novel biphasic bone graft are reported. The bone graft is a physical mixture of calcium sulfate (CS) and hydroxyapatite (HA). This biphasic bone graft was prepared by sintering at 1100 °C. Since the degradation rate of CS is much faster than that of HA, the CS/HA biphasic bone graft exhibits two degradation rates. The degradation rate is rapid (~10 wt%/week) in the first stage and then slow (~1 wt%/week) in the second stage. The biphasic bone graft has been implanted into the distal femur of rat. Most the bone graft was degraded 13 weeks postoperatively. Instead, trabecular bone and vascular tissue are observed at the location of implant. The bone graft is unique for its burst of calcium ions at the start and its ability to remain stable throughout the degradation process. Its stable porous structure serves as an ideal scaffold for the formation of new bone as well as vascularization. • A biphasic bone graft, composing of calcium sulfate and hydroxyapatite, is developed. • The biphasic bone graft exhibits two degradation rates. • Its porous structure serves as an ideal scaffold for the formation of new bone as well as vascularization. [ABSTRACT FROM AUTHOR]

Background: MicroRNA (miRNA) plays a vital role in the intervertebral disc (IVD) degeneration. The expression level of miR-573 was downregulated whereas Bax was upregulated notably in human degenerative nucleus pulposus cells. In this study, we aimed to investigate the role of miR-573 in human degenerative nucleus pulposus (NP) cells following hyperbaric oxygen (HBO) treatment. Methods: NP cells were separated from human degenerated IVD tissues. The control cells were maintained in 5% CO2/95% air and the hyperoxic cells were exposed to 100% O2 at 2.5 atmospheres absolute. MiRNA expression profiling was performed via microarray and confirmed by real-time PCR, and miRNA target genes were identified using bioinformatics and luciferase reporter assays. The mRNA and protein levels of Bax were measured. The proliferation of NPCs was detected using MTT assay. The protein expression levels of Bax, cleaved caspase 9, cleaved caspase 3, pro-caspase 9, and pro-caspase 3 were examined. Results: Bioinformatics analysis indicated that the 3′ untranslated region (UTR) of the Bax mRNA contained the "seed-matched-sequence" for hsa-miR-573, which was validated via reporter assays. MiR-573 was induced by HBO and simultaneous suppression of Bax was observed in NP cells. Knockdown of miR-573 resulted in upregulation of Bax expression in HBO-treated cells. In addition, overexpression of miR-573 by HBO increased cell proliferation and coupled with inhibition of cell apoptosis. The cleavage of pro-caspase 9 and pro-caspase 3 was suppressed while the levels of cleaved caspase 9 and caspase 3 were decreased in HBO-treated cells. Transfection with anti-miR-573 partly suppressed the effects of HBO. Conclusion: Mir-573 regulates cell proliferation and apoptosis by targeting Bax in human degenerative NP cells following HBO treatment. [ABSTRACT FROM AUTHOR]

Cr-C-Ni-diamond composite deposits with synthetic diamond particles of 50 μm in average size were electroplated onto a medium-carbon steel rod to fabricate electroplated diamond grinding rods. To make an electroplated Cr-C-Ni-diamond grinding rod with a high diamond density, three sequential electroplating processes were proposed, including Ni undercoating, Ni-diamond co-electroplating, and Cr-C strengthen-electroplating. The Cr-C strengthening deposit was prepared in an eco-friendly Cr3+-based plating bath. A composite Cr-C-Ni-diamond deposit with multi-layered diamond particles could be prepared on the steel rod substrate by repeating the proposed three sequential electroplating processes. After electroplating, some of the prepared grinding rods were annealed at 500 °C for 30 min to increase the hardness of Cr-C deposit. As-plated and annealed electroplated Cr-C-Ni-diamond grinding rods with one- and two-layered diamond particles were used to grind slots in Al2O3 plates in a depth of 5 mm to evaluate their grinding-life performances. Based on the results of grinding tests, the ground length of an electroplated Cr-C-Ni-diamond grinding rod was significantly increased after annealing at 500 °C for 30 min, and the length was further extended by electroplating two layers of Cr-Cs-Ni-diamond composite deposit. A relatively long ground length of 1320 mm was achieved from the 500 °C-annealed electroplated diamond grinding rod with two-layered diamonds, but only 30 mm from the as-plated one. It was evidenced that an anneal-hardened Cr-C deposit can serve as a competent strengthening layer in the electroplated diamond tool. [ABSTRACT FROM AUTHOR]

Screw loosening due to broken pedicles is a common complication resulting from the insertion of screws either with inadequate diameters or into an osteoporotic pedicle. In this novel in vitro study, we tried to clarify the contribution of the pedicle to screw fixation and subsequent salvage strategies using longer or larger-diameter screws in broken pedicles. Sixty L4 fresh-frozen lumbar vertebrae harvested from mature pigs were designed as the normal-density group (n = 30) and decalcified as the osteoporosis group (n = 30). Three modalities were randomly assigned as intact pedicle (n = 30), semi-pedicle (n = 15), and non-pedicle (n = 15) in each group. Three sizes of polyaxial screws (diameter × length of 6.0 mm × 45 mm, 6.0 mm × 50 mm, and 6.5 mm × 45 mm) over five trials were used in each modality. The associations between bone density, pedicle modality and screw pullout strength were analyzed. After decalcification for 4 weeks, the area bone mineral density decreased to approximately 56% (p < 0.05) of the normal-density group, which was assigned as the osteoporosis group. An appropriate screw trajectory and insertional depth were confirmed using X-ray imaging prior to pullout testing in both groups. The pullout forces of larger-diameter screws (6.5 mm × 45 mm) and longer screws (6.0 mm × 50 mm) were significantly higher (p < 0.05) in the semi- and non-pedicle modalities in the normal-density group, whereas only longer screws (6.0 mm × 50 mm) had a significantly higher (p < 0.05) pullout force in the non-pedicle modalities in the osteoporosis group. The pedicle plays an important role in both the normal bone density group and the osteoporosis group, as revealed by analyzing the pullout force percentage contributed by the pedicle. Use of a longer screw would be a way to salvage a broken pedicle of osteoporotic vertebra. [ABSTRACT FROM AUTHOR]

Accurate and rapid diagnosis of infectious diseases plays a key role in clinical practice, especially in resource-limited countries. In this study, we integrated sunrise-type smart amplification process (s-SmartAmp), a convenient and sensitive isothermal amplification method for nucleic acid, into a portable 3D-printed device equipped with smartphone-assisted image analysis capabilities to develop a novel fluorescence-based sensing system for the on-site diagnosis of tuberculosis (TB). To increase the efficiency of fluorescence (or Förster) resonance energy transfer, two types of sunrise probe systems were compared to detect the IS6110 DNA sequence of TB. Subsequently, linear regression was conducted to compare the performance of s-SmartAmp and loop-mediated isothermal amplification (LAMP). The results indicated that, compared with LAMP, s-SmartAmp yielded more stable and precise results with lower background interference and high linear correlation coefficients (R 2 = 0.9994 and 1, respectively) for the FAM-TAMRA and FITC-BHQ-1 probe system. The detection time was 45 min with a detection limit of 10 fg/μL. To evaluate the performance of our proposed on-site sensing system, we used s-SmartAmp 3D-printed ultraviolet light-emitting diode device to test multiple clinical samples of TB. Our findings suggest that the proposed system has the potential to achieve accurate and rapid on-site diagnosis of TB. [Display omitted] [ABSTRACT FROM AUTHOR]

A considerable propotion of patients with cancer got thoracolumbar vertebral metastatic epidural spinal cord compression, which affected their quality of life. Traditional surgical management involves early decompression with concomitant spine stabilization with long instrumentation. However, complications are caused by massive blood loss and long operation time. This study aimed to compare the safety and efficacy of short posterior instrumentation with kyphoplasty and the traditional method for thoracolumbar metastatic epidural spinal cord compression. Between January 2004 and December 2015, a retrospective study was conducted on 120 patients with metastatic epidural spinal cord compression from T6 to L5 and divided into 2 groups: short posterior instrumentation with the balloon kyphoplasty group (group I, n = 50) and the long posterior instrumentation group (group II, n = 70). The clinical and radiographic parameters of patients in the 2 groups were compared with a nonrandomized cohort method. Patients were followed up from 3 to 40 months after surgery according to survival time. In group I, the surgery had a mean blood loss of 650 mL and a survival time of 19.1 months. In group II, the surgery had a mean blood loss of 2100 mL and a survival time of 14.14 months. A significant difference in blood loss amount (P = 0.002) was observed. Complications, including deep wound infection, durotomy, and uncontrolled bleeding, were observed in both groups. No postoperative cement-induced neurologic deterioration, implant failure occurred. Kyphoplasty with short posterior instrumentation is a novel technique that can be performed safely and effectively for the treatment of thoracolumbar metastatic epidural spinal cord compression. Rigid stability, reduced blood loss, and short fixation decrease surgical morbidity of spinal metastasis. [ABSTRACT FROM AUTHOR]

Ni–diamond and Ni–B–diamond composite deposits were electroplated with a current density of 20 A/dm2 on a steel cylinder with a diameter of 6.0 mm in a Ni-Watt bath with different tetramethylammonium borohydride (TMAB) concentrations and 300-g/L synthetic diamond particles with sizes between 30 and 50 μm. Prior to Ni–diamond or Ni–B–diamond composite electroplating, a Ni undercoating with a thickness of 50 μm was electroplated on the steel cylinder. During composite electroplating, diamond particles were intermittently stirred with different stirring cycles in the plating bath. Experimental results show the distribution of diamond particles in the Ni or Ni–B deposit depends strongly on the stirring cycle. A composite deposit with a high diamond density can be achieved with intermittent stirring by using an on the period of 5 s and an off period of 80 s. From the results of milling test, an electroplated Ni–B–diamond milling tool with a high milling ability can be achieved after annealing at 300 °C or 500 °C for 30 min. [ABSTRACT FROM AUTHOR]

Background Traditionally, nonoperative management with long-term antibiotics and bed rest has been recommended as first-line treatment for most patients with postoperative discitis. A recent trend in treatment under a limited range of indications has been to perform surgical débridement followed by long-term administration of antibiotics. This descriptive study investigated whether transforaminal lumbar interbody débridement and fusion (TLIDF) combined with intravenous antibiotics is appropriate to manage postdiscectomy discitis. Methods This study retrospectively analyzed demographic data, laboratory data, and radiography and magnetic resonance imaging of 10 patients with postoperative discitis who underwent surgical TLIDF followed by antibiotic treatment. Preoperative and postoperative spine sagittal alignment, visual analog scale scores, and Kirkaldy-Willis criteria for functional outcomes were evaluated. Results An infection clearance rate of 100% was ultimately achieved for the patients who underwent TLIDF with short posterior instrumentation. TLIDF yielded better outcomes than traditional conservative treatment in terms of spine alignment correction, functional outcomes, and quality of life. Conclusions Based on previously reported data and the findings of this study, we suggest that surgical intervention should be used in certain cases, as it can achieve better outcomes than conservative treatment. We recommend a novel single posterior approach with TLIDF and posterior pedicle screw instrumentation for management of postdiscectomy discitis. Highlights • A retrospective study analyzed clinical data in 10 patients with postdiscectomy discitis who underwent TLIDF. • TLIDF and IV antibiotics achieved better functional outcomes and higher infection clearance than conservative treatment. • We present a novel single posterior approach with TLIDF and short posterior pedicle screw instrumentation. • Our novel approach is a safe and effective treatment for postdiscectomy discitis. [ABSTRACT FROM AUTHOR]

[Display omitted] • The TiO 2 -based H 2 production system (UST NPs) is designed to ease inflammation. • The UST NPs contain upconversion nanoparticles coated with SiO 2 @TiO 2 double-shells. • The UCNP core transduces light; SiO 2 @TiO 2 double-shells serve as a photocatalyst. • The UST NPs produce H 2 by using lactate as a sacrificial agent in inflamed tissues. During tissue infection, immune cells undergo glycolysis, generating lactate that intensifies inflammation and contributes to the excessive production of reactive oxygen species (ROS) and pro-inflammatory cytokines. TiO 2 serves as a photocatalyst capable of splitting water and producing H 2 when activated by UV light. The study proposes the clinical application of TiO 2 to combat tissue inflammation, building upon the antioxidative properties of H 2. To address the limited tissue penetration depth of UV light, a TiO 2 -based photocatalytic H 2 production system is developed, utilizing upconversion nanoparticles (UCNPs) coated with a double-shell structure of SiO 2 and TiO 2 (UST NPs). The efficiency of the UST NPs relies on the utilization of tissue-penetrating near-infrared (NIR) light, which is converted to UV light by the UCNP core. Additionally, the SiO 2 @TiO 2 double-shell enhances light absorbance efficiency and photocatalytic activity. When exposed to NIR light, the UST NPs have the potential to effectively enhance H 2 production by utilizing lactate as a sacrificial agent in inflamed tissues, while also facilitating the photocatalytic water splitting process. Consequently, UST NPs + NIR efficiently deplete accumulated lactate in inflamed tissues, reducing inflammation by utilizing the produced H 2 to scavenge ROS and pro-inflammatory cytokines. The study explores the innovative application of TiO 2 -based materials as a photocatalyst, providing fresh perspectives on enhancing H 2 production efficiency through the utilization of UCNPs, NIR light, and glycolysis-generated waste (lactate) in inflammation, and examining its relevance in the medical field. [ABSTRACT FROM AUTHOR]

The 3D-printed Ti-6Al-4V intervertebral fusion cage is fabricated to be biocompatible with improved stiffness, fatigue life, and osteogenic differentiation, which are greatly enhanced by heat treatment and surface modification. The flexible cage's life, which exceeds the standard dynamic fatigue requirement of 5 × 106 cycles based on the ASTM F2077 and F2267 test methods, is achieved by heat treatment at 800 ℃ in argon atmosphere, shot peening, and adjusting the α to β phase ratio to increase mechanical toughness. Surface modification via sandblasting and chemical etching removes the surface oxide layer and forms submicron pores on the surface of the cage, which significantly boosts cell proliferation, differentiation, and osteoblast mineralization. This work exhibits a novel design of Ti-6Al-4V intervertebral fusion cage with biocompatible stiffness, enhanced fatigue life, and improved osteogenic differentiation achieved by reducing residual stress, modifying surface micro-pores, and optimizing microstructure. [Display omitted] • Ti-6Al-4V intervertebral cage with biocompatible stiffness, enhanced fatigue life, and improved osteogenic differentiation. • Heat treatment and shot peening to adjust residual stress and optimizing microstructure to increase mechanical toughness. • Sandblasting and chemical etching boost cell proliferation, differentiation, and osteoblast mineralization. [ABSTRACT FROM AUTHOR]

Background: Correcting the scoliosis and stabilizing the spine in the corrected position is the basis of treatment for adolescent idiopathic scoliosis (AIS). Spinal instrumentation and derotation are the principle steps of surgery for any type of AIS. A perspicuous understanding needs to be attained regarding derotation maneuvers in practice; therefore, we intend to compare radiological outcomes following concave and convex rod derotation maneuvers to analyze their efficacy to correct selective Lenke’s Type-1 scoliosis Materials and Methods: Retrospectively, 88 patients with Lenke’s Type-1 scoliosis who were operated with selective thoracic instrumentation were divided into two groups depending on the derotation side. Preoperative radiographs were analyzed for curve angles, thoracic apical vertebral translation, apical vertebral rotation, and coronal/sagittal balance. Postoperative and followup assessment was focused on curve correction. Correction rate of main thoracic (MT) curve and its corresponding loss of correction at final followup are calculated Results: Concave group (n = 40; age 13.8 ± 1.9) and the convex group (n = 48; Age 14.3 ± 2.4) showed similar demographic characteristics. Postoperative and followup parameters showed no significant difference. Correction rate of MT curve between both groups (concave group = 69.2 ± 10.5%; convex group = 66 ± 12.8%; P = 0.20) was similar. There was minimal loss of correction at final followup among both groups (concave group = 2.2º ±5.4º; Convex group = 1.5º ± 4.8º; P = 0.52) Conclusion: The study results showed similar sustained satisfactory correction of flexible Lenke’s type 1 scoliotic curves irrespective of the derotation maneuver used. Adequate correction, thereby restoring balance was predominantly perceived among the entire sample. Hence, convex derotation can be considered equally effective as that of concave derotation for achieving adequate correction of selective Lenke’s Type-1 scoliosis [ABSTRACT FROM AUTHOR]

Healing of large calvarial bone defects in adults is challenging. We previously showed that inducing chondrogenic differentiation of mesenchymal stem cells from bone marrow (BMSC) or adipose tissue (ASC) before implantation can switch the repair pathway and improve calvarial bone healing. Split dCas12a activator is a new CRISPR activation system comprising the amino (N) and carboxyl (C) fragments of dCas12a protein, each being fused with synthetic transcription activators at both termini. The split dCas12a activator was shown to induce programmable gene expression in cell lines. Here we exploited the split dCas12a activator to activate the expression of chondroinductive long non-coding RNA H19. We showed that co-expression of the split N- and C-fragments resulted in spontaneous dimerization, which elicited stronger activation of H19 than full-length dCas12a activator in rat BMSC and ASC. We further packaged the entire split dCas12a activator system (13.2 kb) into a hybrid baculovirus vector, which enhanced and prolonged H19 activation for at least 14 days in BMSC and ASC. The extended H19 activation elicited potent chondrogenic differentiation and inhibited adipogenesis. Consequently, the engineered BMSC promoted in vitro cartilage formation and augmented calvarial bone healing in rats. These data implicated the potentials of the split dCas12a activator for stem cell engineering and regenerative medicine. [ABSTRACT FROM AUTHOR]

Background context Mesenchymal stem cell (MSC)–based cell therapy and gene transfer have converged and show great potential for accelerating bone healing. Gene therapy can provide more sustained expression of osteogenic factors such as bone morphogenetic protein-2 (BMP-2). We previously demonstrated that low-dose BMP-2 enhanced spinal posterolateral fusion by MSCs in a rabbit model. Herein, we genetically modified rabbit MSCs with a recombinant baculovirus encoding BMP-2 (Bac-CB) and vascular endothelial growth factor (Bac-VEGF) seeded into porous scaffolds to enhance spinal fusion. Purpose This study evaluates the success rate of the MSC-based cell therapy and gene transfer approach for single-level posterolateral spine fusion. We hypothesize that combining three-dimensional tricalcium phosphate (TCP) scaffolds and genetically modified allogeneic MSCs with baculovirus-mediated growth factor expression would increase the success rate of spinal fusion. Study design The study design was based on an animal model (approved by the Institutional Animal Care and Use Committee) using 18 adult male New Zealand rabbits. Methods This study included 18 male New Zealand rabbits, weighing 3.5 to 4 kg. Allogeneic bone marrow–derived MSCs were isolated and genetically modified with Bac-CB and Bac-CV seeded onto TCP scaffolds (MSC/Bac/TCP). The animals were divided into three groups according to the material implanted into the bilateral L4–L5 intertransverse space: TCP scaffold (n=6), MSC/TCP (n=6), and MSC/Bac/TCP (n=6). After 12 weeks, the rabbits were euthanized for radiographic examination, manual palpation, and histologic study. Results Bilateral fusion areas in each animal were evaluated independently. The radiographic fusion rates at 12 sites were 0 of 12 in the TCP scaffold group, 4 of 12 in the MSC/TCP group, and 10 of 12 in the MSC/Bac/TCP group. By manual palpation, there were zero solid fusions in the TCP scaffold group, two solid fusions in the MSC/TCP group, and five solid fusions in the MSC/Bac/TCP group. Fusion rates were significantly greater in the MSC/Bac/TCP group. Conclusions The results indicate the potential of using baculovirus as a vector for gene/cell therapy approaches to improve bone healing and support the feasibility of using allogeneic MSCs for inducing bone formation and intertransverse process fusion. [ABSTRACT FROM AUTHOR]

Calcium sulfate is a degradable bioceramic; its pellets have been used as bone void fillers for more than 100 years. However, the use of calcium sulfate bioceramic as a bone graft substitute is limited by its low strength and rapid degradation rate. In the present study, a small amount of glass (1 wt%) is incorporated into calcium sulfate powder. Dense glass-doped calcium sulfate pellets are prepared by sintering at 900 °C for 1 h. Though the amount of glass is low, the compressive strength of the pellets is enhanced by 40%; the degradation rate is reduced by nearly an order of magnitude. [ABSTRACT FROM AUTHOR]

This work reports a new CaO-MgO-SiO 2 (CMS) bioactive glass-ceramic, using ZrO 2 as a nucleus to modulate the ratios of glass and ceramic phases as a function of sintering temperature. Mg-rich bioactive CMS glass-ceramics exhibit advantages regarding mechanical strength (flexural strength ~190 MPa and compressive strength ~555 MPa), in-vitro and in-vivo biocompatibilities, and bone ingrowth. The high mechanical strengths could be attributed to the CaMgSi 2 O 6 glass-ceramic and lower porosity. X-ray absorption spectra indicate an increased Si O covalent bond via the development of CaMgSi 2 O 6 glass-ceramics. From the in-vitro cytotoxicity and BMSC differentiation assays, the CMS samples sintered above 800 °C exhibited better cell attachment and differentiation, possibly due to structural stability, appropriate pore, and ion release to boost osteogenesis. Compared to hydroxyapatite (HA) ceramics, the CMS glass-ceramics display higher mechanical strengths, biocompatibility, and osteoconductivity. An in-vivo experiment demonstrated a fine bone-ingrowth profile around the CMS implant. This study may further the application of CMS glass-ceramics in bone implants. • A new CaO-MgO-SiO 2 (CMS) bioactive glass-ceramics by sintering temperature to modulate the ratios of glass and ceramic phases. • CMS glass-ceramics display higher mechanical strengths, biocompatibility, and osteoconductive differentiation than HA. • In-vivo experiment demonstrated an excellent bone-ingrowth around the CMS implant. • This work may open an opportunity for using CMS glass-ceramics in bone implants. [ABSTRACT FROM AUTHOR]

Resorbable bioceramics offer advantages in healing bone defects due to their degradation capability. Degradation rates differ significantly from one bioceramic to another; nevertheless, the degradation rate should match the growth rate of new bone. In the present study, a head-to-head comparison of the degradation rate of calcium sulfate and tricalcium phosphate is conducted. First, the degradation behaviors of calcium sulfate and tricalcium phosphate are evaluated separately. The comparison indicates that the degradation rate of calcium sulfate is one order of magnitude faster than that of tricalcium phosphate. Along with a fast degradation rate, the formation of calcium phosphate on the surface of calcium sulfate pellets is also faster. A core-shell roll composed of a calcium sulfate core and a tricalcium phosphate shell is also prepared. After soaking the core-shell roll in phosphate buffered saline solution for 24 h, calcium phosphate precipitates form only on the surface of core, the part containing calcium sulfate anhydrite. • The degradation behaviors of calcium sulfate and tricalcium phosphate are evaluated separately. • A unique design to evaluate the degradation behavior of bioceramics is proposed. • The biodegradable rate could be adjusted by the two components composite for clinic use. [ABSTRACT FROM AUTHOR]

CRISPR/Cas9 system exploits the concerted action of Cas9 nuclease and programmable single guide RNA (sgRNA), and has been widely used for genome editing. The Cas9 nuclease activity can be abolished by mutation to yield the catalytically deactivated Cas9 (dCas9). Coupling with the customizable sgRNA for targeting, dCas9 can be fused with transcription repressors to inhibit specific gene expression (CRISPR interference, CRISPRi) or fused with transcription activators to activate the expression of gene of interest (CRISPR activation, CRISPRa). Here we introduce the principles and recent advances of these CRISPR technologies, their delivery vectors and review their applications in stem cell engineering and regenerative medicine. In particular, we focus on in vitro stem cell fate manipulation and in vivo applications such as prevention of retinal and muscular degeneration, neural regeneration, bone regeneration, cartilage tissue engineering, as well as treatment of diseases in blood, skin and liver. Finally, the challenges to translate CRISPR to regenerative medicine and future perspectives are discussed and proposed. [ABSTRACT FROM AUTHOR]

The research retrospectively analyzed cases of spinal chordoma and chondrosarcoma involving patients who received treatment at the two hospitals between 2001 and 2023. Among the 48 patients studied (39 chordoma and 9 chondrosarcoma cases), the average age was 53.9 ± 15.8 years, with a range of 17 to 86 years. Out of these patients, 43 underwent excision surgery and were categorized based on tumor margin into negative (R0) or microscopically positive (R1) margin (n = 14) and macroscopically positive (R2) margin (n = 29) groups. The mean overall survival (OS) for R0/R1 and R2 groups was 156.5 ± 19.3 and 79.2 ± 11.9 months, respectively (p value = 0.012). The mean progression-free survival (PFS) for R0/R1 and R2 was 112.9 ± 24.4 and 25.5 ± 5.5 months (p value < 0.001). The study showed that regardless of whether patients in the R0/R1 or R2 groups received radiation therapy (RT) or not, there was no significant improvement in OS or PFS. Specifically, the OS and PFS for the RT only group were 75.9 ± 16.6 and 73.3 ± 18.0 months. In conclusion, the recommended treatment approach for spinal chordoma and chondrosarcoma remains en bloc resection surgery with an appropriate margin. Patients who are unsuitable for or decline surgery may find a beneficial disease control rate with traditional external beam photon/proton therapy., (© 2024. The Author(s).)

The current surgical adjunctive for vitreoretinal surgeries fails to provide an adequate 3D structure for cellular regeneration. A one-pot synthesis of gelatin-methacryloyl (GelMA) followed by modification with 4-carboxyphenylboronic acid (4-CPBA) was performed to fabricate 4-CPBA-modified GelMA (4CPBA@GelMA), a gelatin-based hydrogel. 4CPBA@GelMA was photo-cross-linked by 405 nm violet light and examined using nuclear magnetic resonance (NMR), Fourier-transform infrared spectrometry (FTIR), scanning electron microscopy (SEM), and rheometry. In vitro biocompatibility was examined by Müller cell proliferation assays exposed to 4CPBA@GelMA and violet light. In vivo retinal biocompatibility was evaluated by electroretinography of rat eyes that were exposed to intravitreally injected and photo-cross-linked 4CPBA@GelMA at days 3, 7, 14, and 28 post-injection. Following electroretinography, histology and immunohistochemistry were performed on the retinas. The NMR results indicated amidation of GelMA by 4-CPBA, and FTIR confirmed the presence of the CPBA ring in 4CPBA@GelMA samples. SEM revealed that 4CPBA@GelMA had significantly larger pores than GelMA (56.9 ± 9.5 vs 35.1 ± 2.8 μm; P < 0.001). Rheological findings showed that, unlike GelMA and gelatin, 4CPBA@GelMA has Newtonian fluid properties at room temperature. Exposure to 4CPBA@GelMA did not significantly affect Müller cell viability in a proliferation assay; moreover, electroretinography findings indicated normal waveforms and implicit times, and histology and immunohistochemistry examinations revealed no significant changes. In this study, we established the high retinal compatibility of 4CPBA@GelMA. The low viscosity of 4CPBA@GelMA is ideal for injection via small-gauge needles, and the larger pore size and three-dimensional network both potentiate cellular migration and growth. These features made 4CPBA@GelMA a candidate for vitreoretinal surgical adjunctive that might promote retinal regeneration., Competing Interests: The authors declare no competing financial interest., (© 2024 The Authors. Published by American Chemical Society.)

This study develops a composite bone graft of CaO-MgO-SiO 2 glass-ceramic and CaSO 4 [abbreviated as (CMS) 3- x (CS) x ] via the sponge replication technique with weight fractions of x = 0, 1, 1.5, 2, and 3. The (CMS) 1.5 (CS) 1.5 composite displays a superior degradability and, a suitable compressive strength of ∼3 MPa, and excellent cell proliferation and differentiation. The in vivo rat femur test in the hybrid-pore (CMS) 1.5 (CS) 1.5 composite granules achieves a higher rate of bone formation, which is ∼2.7 times better than that of the commercial HAP/β-TCP at 12 weeks. Improved expressions of osteocyte and mature osteocyte marker genes, namely (Spp1, Dmp1, and Fgf23), were observed in the (CMS) 1.5 (CS) 1.5 group, indicating a faster differentiation into mature bone tissue. The ions release of (CMS) 1.5 (CS) 1.5 through the ERK1/2 signaling pathway promotes osteogenic differentiation. The high bone generation rate can be attributed to faster active ions release and modified surface topography. This work highlights an excellent bone graft candidate for clinical applications in orthopedic surgery.

Objective: To evaluate the association of serum 25-hydroxyvitamin D (25(OH) D) levels with bone mineral density (BMD), fracture risk, and bone metabolism., Methods: This multicenter cross-sectional study recruited menopausal females and males greater than or equal to 50 year old with osteoporosis/fractures between September 2016 and September 2021. Assessment included clinical data, 25(OH)D, intact parathyroid hormone (iPTH), procollagen type 1 amino-terminal propeptide (P1NP), carboxy-terminal collagen crosslinks (CTX), lateral thoracolumbar spine x-rays, and BMD., Results: A total of 3003 individuals were stratified by 25(OH) D levels: 720 individuals (24%) <20 ng/mL, 1338 individuals (44.5%) 20 to 29 ng/mL, and 945 individuals (31.5%) ≥30 ng/mL. In unadjusted and multivariable models, BMD T-score, except spine, was significantly and positively associated with 25(OH)D levels. 25(OH) D levels were inversely associated with Fracture Risk Assessment Tool scores. Patients with 25(OH)D <20 ng/mL had significantly higher iPTH and bone turnover markers (P1NP and CTX) than patients with 25(OH)D ≧20 ng/mL in all models. When analyzing bone-related markers and BMD, total hip and femoral neck BMD T-scores were positively correlated with 25(OH)D concentrations and BMI but negatively correlated with iPTH, P1NP, CTX, and age. In multivariate models with all bone-related markers, only 25(OH)D levels were significantly associated with total hip and femoral neck BMD., Conclusion: Vitamin D deficiency is significantly associated with decreased total hip and femoral neck BMD and increased fracture risk as assessed by Fracture Risk Assessment Tool. In those with osteoporosis/fractures, vitamin D is implicated in the causal relationship between bone remodeling and BMD. Assessing vitamin D status is imperative for those at risk for osteoporosis/fractures., Competing Interests: Disclosure The authors have no multiplicity of interest to disclose., (Copyright © 2024. Published by Elsevier Inc.)

Nonunion resulting from early bone resorption is common after bone transplantation surgery. In these patients, instability or osteoporosis causes hyperactive catabolism relative to anabolism, leading to graft resorption instead of fusion. Systemic zoledronate administration inhibits osteoclastogenesis and is widely used to prevent osteoporosis; however, evidence on local zoledronate application is controversial due to osteoblast cytotoxicity, uncontrolled dosing regimens, and local release methods. We investigated the effects of zolendronate on osteoclastogenesis and osteogenesis and explored the corresponding signaling pathways. In vitro cytotoxicity and differentiation of MC3T3E1 cells, rat bone marrow stromal cells (BMSCs) and preosteoclasts (RAW264.7 cells) were evaluated with different zolendronate concentrations. In vivo bone regeneration ability was tested by transplanting different concentrations of zolendronate with β-tricalcium phosphate (TCP) bone substitute into rat femoral critical-sized bone defects. In vitro , zolendronate concentrations below 2.5 × 10 -7  M did not compromise viability in the three cell lines and did not promote osteogenic differentiation in MC3T3E1 cells and BMSCs. In RAW264.7 cells, zoledronate inhibited extracellular regulated protein kinases and c-Jun n-terminal kinase signaling, downregulating c-Fos and NFATc1 expression, with reduced expression of fusion-related dendritic cell‑specific transmembrane protein and osteoclast-specific Ctsk and tartrate-resistant acid phosphatase (. In vivo , histological staining revealed increased osteoid formation and neovascularization and reduced fibrotic tissue with 500 μM and 2000 μM zolendronate. More osteoclasts were found in the normal saline group after 6 weeks, and sequential osteoclast formation occurred after zoledronate treatment, indicating inhibition of bone resorption during early callus formation without inhibition of late-stage bone remodeling. In vivo , soaking β-TCP artificial bone with 500 μM or 2000 μM zoledronate is a promising approach for bone regeneration, with potential applications in bone transplantation., Competing Interests: None., (© The Author(s) 2024. Published by Oxford University Press on behalf of the American Society for Bone and Mineral Research.)

Despite advancements in pedicle screw design and surgical techniques, the standard steps for inserting pedicle screws still need to follow a set of fixed procedures. The first step, known as establishing a pilot hole, also referred to as a pre-drilled hole, is crucial for ensuring screw insertion accuracy. In different surgical approaches, such as minimally invasive or traditional surgery, the method of creating pilot holes varies, resulting in different pilot hole profiles, including variations in size and shape. The aim of this study is to evaluate the biomechanical properties of different pilot hole profiles corresponding to various surgical approaches. Commercially available synthetic L4 vertebrae with a density of 0.16 g/cc were utilized as substitutes for human bone. Four different pilot hole profiles were created using a 3.0 mm cylindrical bone biopsy needle, 3.6 mm cylindrical drill, 3.2-5.0 mm conical drill, and 3.2-5.0 mm conical curette for simulating various minimally invasive and traditional spinal surgeries. Two frequently employed screw shapes, namely, cylindrical and conical, were selected. Following specimen preparation, screw pullout tests were performed using a material test machine, and statistical analysis was applied to compare the mean maximal pullout strength of each configuration. Conical and cylindrical screws in these four pilot hole configurations showed similar trends, with the mean maximal pullout strength ranking from high to low as follows: 3.0 mm cylindrical biopsy needle, 3.6 mm cylindrical drill bit, 3.2-5.0 mm conical curette, and 3.2-5.0 mm conical drill bit. Conical screws generally exhibited a greater mean maximal pullout strength than cylindrical screws in three of the four different pilot hole configurations. In the groups with conical pilot holes, created with a 3.2-5.0 mm drill bit and 3.2-5.0 mm curette, both conical screws exhibited a greater mean maximal pullout strength than did cylindrical screws. The strength of this study lies in its comprehensive comparison of the impact of various pilot hole profiles commonly used in clinical procedures on screw fixation stability, a topic rarely reported in the literature. Our results demonstrated that pilot holes created for minimally invasive surgery using image-guided techniques exhibit superior pullout strength compared to those utilized in traditional surgery. Therefore, we recommend prioritizing minimally invasive surgery when screw implantation is anticipated to be difficult or there is a specific need for stronger screw fixation. When opting for traditional surgery, image-guided methods may help establish smaller pilot holes and increase screw fixation strength., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2024 Li, Lai, Hsieh, Chen, Lee, Tsai and Tai.)

This study aimed to design an anatomical contour metal three-dimensional (3D)-printed oblique lateral lumbar interbody fusion (OLIF) cage with porous (lattices) structure and embedded screw fixation to enhance bone ingrowth to reduce the risk of cage subsidence and avoid the stress-shielding effect. Finite element (FE) analysis and weight topology optimization (WTO) were used to optimize the structural design of the OLIF cage based on the anatomical contour morphology of patients with osteoporosis. Two oblique embedded fixation screws and lattice design with 65% porosity and average pore size of 750 μm were equipped with the cage structure. The cage was fabricated via metal 3D printing, and static/dynamic compression and compressive-shear tests were performed in accordance with the ASTM F2077-14 standard to evaluate its mechanical resistance. On FE analysis, the OLIF cage with embedded screw model had the most stability, lowest stress values on the endplate, and uniform stress distribution versus standalone cage and fixed with lateral plate under extension, lateral flexion, and rotation. The fatigue test showed that the stiffnesses/endurance limits (pass 5 million dynamic test) were 16,658 N/mm/6000 N for axial load and 19,643 N/mm/2700 N for compression shear. In conclusion, an OLIF cage with embedded fixation screws can be designed by integrating FE and WTO analysis based on the statistical results of endplate morphology. This improves the stability of the OLIF cage to decrease endplate destruction. The complex contour and lattice design of the OLIF cage need to be manufactured via metal 3D printing; the dynamic axial compression and compressive-shear strengths are greater than that of the U.S. Food and Drug Administration (FDA) standard., Competing Interests: The authors declare no conflicts of interest., (Copyright:© 2023, Lai P-L, Huang S-F, Wang H-W, et al.)

Ball-and-socket designs of cervical total disc replacement (TDR) have been popular in recent years despite the disadvantages of polyethylene wear, heterotrophic ossification, increased facet contact force, and implant subsidence. In this study, a non-articulating, additively manufactured hybrid TDR with an ultra-high molecular weight polyethylene core and polycarbonate urethane (PCU) fiber jacket, was designed to mimic the motion of normal discs. A finite element (FE) study was conducted to optimize the lattice structure and assess the biomechanical performance of this new generation TDR with an intact disc and a commercial ball-and-socket Baguera ® C TDR (Spineart SA, Geneva, Switzerland) on an intact C5-6 cervical spinal model. The lattice structure of the PCU fiber was constructed using the Tesseract or the Cross structures from the IntraLattice model in the Rhino software (McNeel North America, Seattle, WA) to create the hybrid I and hybrid II groups, respectively. The circumferential area of the PCU fiber was divided into three regions (anterior, lateral and posterior), and the cellular structures were adjusted. Optimal cellular distributions and structures were A2L5P2 in the hybrid I and A2L7P3 in the hybrid II groups. All but one of the maximum von Mises stresses were within the yield strength of the PCU material. The range of motions, facet joint stress, C6 vertebral superior endplate stress and path of instantaneous center of rotation of the hybrid I and II groups were closer to those of the intact group than those of the Baguera ® C group under 100 N follower load and pure moment of 1.5 Nm in four different planar motions. Restoration of normal cervical spinal kinematics and prevention of implant subsidence could be observed from the FE analysis results. Superior stress distribution in the PCU fiber and core in the hybrid II group revealed that the Cross lattice structure of a PCU fiber jacket could be a choice for a next-generation TDR. This promising outcome suggests the feasibility of implanting an additively manufactured multi-material artificial disc that allows for better physiological motion than the current ball-and-socket design., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Hsieh, Tai, Li, Lee, Lin, Tsai, Lai and Chen.)

Intraoperative pedicle screw depth adjustment after initial insertion, including both forward and backward adjustments, is sometimes necessary to facilitate rod application and ensure that the screw is in the correct position, which is determined by intraoperative fluoroscopy. Adjusting the screw with forward turns has no negative influence on the screw fixation stability; however, screw turnback may weaken the fixation stability. The aim of this study is to evaluate the biomechanical properties of screw turnback and demonstrate the reduction in the fixation stability after the screw is turned 360° from its full insertion position. Commercially available synthetic closed-cell polyurethane foams with three different densities simulating various degrees of bone density were utilized as substitutes for human bone. Two different screw shapes (cylindrical and conical) together with two different pilot hole profiles (cylindrical and conical) were tested. Following specimen preparation, screw pullout tests were conducted using a material test machine. The mean maximal pullout strength between full insertion and 360-degree turnback from full insertion in each setting was statistically analyzed. The mean maximal pullout strength after 360-degree turnback from full insertion was generally lower than that at full insertion. The reduced mean maximal pullout strength after turnback increased with decreasing bone density. Conical screws had significantly lower pullout strength after 360-degree turnback than cylindrical screws. The mean maximal pullout strength was reduced by up to approximately 27% after 360-degree turnback when using a conical screw in a low bone density specimen. Additionally, specimens treated with a conical pilot hole presented a less reduction in pullout strength after screw turnback as compared to those with a cylindrical pilot hole. The strength of our study was that we systematically investigated the effects of various bone densities and screw shapes on screw stability after turnback, which has rarely been reported in the literature. Our study suggests that pedicle screw turnback after full insertion should be reduced in spinal surgeries, particularly procedures that use conical screws in osteoporotic bone. Pedicle screw secured with a conical pilot hole might be beneficial for screw adjustment., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Li, Hsieh, Chen, Lee, Tsai, Lai and Tai.)

Study Design: A retrospective cohort study., Objective: To investigate the factors contributing to the development of postoperative distal junctional kyphosis (DJK) in adolescent idiopathic scoliosis (AIS) patients who underwent posterior spinal fusion (PSF) with lowest instrumented vertebrae (LIV) at or above L1., Methods: Patients with Lenke type 1 or 2 curves who underwent PSF with LIV at or above L1 with a minimum follow-up of 2 years were evaluated. The primary outcome measure was the occurrence of postoperative DJK. Radiographic parameters of sagittal alignment and inclusion/exclusion of sagittal stable vertebra (SSV) in PSF were analyzed to determine their associations with the occurrence of postoperative DJK., Results: Overall, 122 patients (mean age: 15.1 ± 3.2 years) were included. The overall incidence of postoperative DJK was 6.6%. DJK was observed in 19.0% (8/42) of patients whose SSV was not included in PSF and not in patients with SSV included in PSF (n = 80). In the SSV-excluded group, univariate analysis found two significant risk factors for DJK: postoperative thoracic kyphosis (TK, T5-12) and postoperative thoracolumbar kyphosis (TLK, T11-L2). The ROC curve revealed that postoperative TK ≥ 25° and TLK ≥ 10° best predicted the occurrence of postoperative DJK in the SSV-excluded group. The incidence was significantly higher in cases with postoperative TK ≥ 25° or TLK ≥ 10° (7/13 = 53.8%) than in those with postoperative TK < 25° and TLK < 10° (1/29 = 3.4%)., Conclusions: The current study revealed that postoperative TK ≥ 25° or postoperative TLK ≥ 10° with SSV excluded from PSF were related to DJK after PSF for Lenke type 1 and type 2 AIS. When the SSV is intended to be spared from PSF to save more motion segments, TK and TLK should be carefully evaluated and attained in a lesser magnitude (TK < 25°, TLK < 10°) after surgery.

Study Design: Biomechanical study., Objective: Cross-links are a type of common clinical spinal instrumentation. However, the effects of the position and number of cross-links have never been investigated in long-segment spinal fixation, and the variables have not been optimized. We conducted an in vitro biomechanical study by using a porcine long-segment spinal model with 5 different crosslink configurations to determine the optimal construct for clinical practice., Methods: Five modalities with paired segmental screws from T15-L5 were tested in 20 porcine spines. The spines without cross-links composed the control group, Group A; those with a single cross-link from L2-3 composed Group B; those with 2 cross-links from L1-2 and L3-4 composed Group C; those with 2 cross-links from T15-L1 and L4-5 composed Group D; and those with 3 cross-links from T15-L1, L2-3 and L4-5 composed Group E. Spinal stiffnesses in flexion, extension, lateral bending, and axial rotation were compared among 5 different cross-link configurations in 5-level porcine spinal units., Results: Flexional, extensional and lateral bending stiffnesses did not significantly change with an increasing number of cross-links or positions in the construct. Axial stiffness was significantly increased with 2 cross-links compared to one ( P < 0.05) and with placement more distant from the center of the long spinal fixation construct ( P < 0.05)., Conclusions: Two cross-links individually placed proximal and distal from the center of a construct is an optimal and efficient configuration to achieve biomechanical stability in non-rigid lumbar spines undergoing long-level fixation.

Three key factors are responsible for the biomechanical performance of pedicle screw fixation: screw mechanical characteristics, bone quality and insertion techniques. To the best of the authors' knowledge, no study has directly compared the biomechanical performance among three trajectories, i.e., the traditional trajectory (TT), modified trajectory (MT) and cortical bone trajectory (CBT), in a porcine model. This study compared the pullout strength and insertion torque of three trajectory methods in single vertebrae, the pullout strength and fixation stiffness including flexion, extension, and lateral bending in a one-level instrumented functional spinal unit (FSU) that mimics the in vivo configuration were clarified. A total of 18 single vertebrae and 18 FSUs were randomly assigned into three screw insertion methods ( n = 6 in each trajectory group). In the TT group, the screw converged from its entry point, passed completely inside the pedicle, was parallel to the superior endplate, was located in the superior third of the vertebral body and reached to at least the anterior third of the vertebral body. In the MT group, the convergent angle was similar to that of the TT method but directed caudally to the anterior inferior margin of the vertebral body. The results of insertion torque and pullout strength in single vertebrae were analyzed; in addition, the stiffness and pullout strength in the one-level FSU were also investigated. This study demonstrated that, in single vertebrae, the insertion torque was significantly higher in CBT groups than in TT and MT groups ( p < 0.05). The maximal pullout strength was significantly higher in MT groups than in TT and CBT groups ( p < 0.05). There was no significant difference in stiffness in the three motions among all groups. The maximal pullout strength in FSUs of MT and CBT groups were significantly higher than the TT groups ( p < 0.05). We concluded that either MT or CBT provides better biomechanical performance than TT in single vertebrae or FSUs. The lack of significance of stiffness in FSUs among three methods suggested that MT or CBT could be a reasonable alternative to TT if the traditional trajectory was not feasible., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2022 Tai, Chen, Liu, Li, Tsai, Lai and Hsieh.)

The application of 3D printing technologies fields for biological tissues, organs, and cells in the context of medical and biotechnology applications requires a significant amount of innovation in a narrow printability range. 3D bioprinting is one such way of addressing critical design challenges in tissue engineering. In a more general sense, 3D printing has become essential in customized implant designing, faithful reproduction of microenvironmental niches, sustainable development of implants, in the capacity to address issues of effective cellular integration, and long-term stability of the cellular constructs in tissue engineering. This review covers various aspects of 3D bioprinting, describes the current state-of-the-art solutions for all aforementioned critical issues, and includes various illustrative representations of technologies supporting the development of phases of 3D bioprinting. It also demonstrates several bio-inks and their properties crucial for being used for 3D printing applications. The review focus on bringing together different examples and current trends in tissue engineering applications, including bone, cartilage, muscles, neuron, skin, esophagus, trachea, tympanic membrane, cornea, blood vessel, immune system, and tumor models utilizing 3D printing technology and to provide an outlook of the future potentials and barriers., (© 2021. The Author(s), under exclusive licence to Springer Nature B.V.)

Background: Minimally invasive surgery (MIS) has become a feasible option for patients with spinal metastasis, but the effectiveness of percutaneous pedicle screw fixation (PPSF) without decompression in patients with severe cord compression remains unknown. We compared PPSF without decompression with debulking surgery in patients with radiosensitive, unstable, metastatic thoracolumbar spinal cord compression., Methods: A retrospective study of surgically treated spinal metastasis and spinal cord compression patients was conducted between October 2014 and June 2019. Demographic and pre- and postoperative data were collected and compared between patients treated with minimally invasive percutaneous fixation and external beam radiotherapy (EBRT) (the PPSF group) and those treated with debulking surgery (the debulking group)., Results: We included 50 patients in this study. The PPSF group had a significantly shorter operative time (143.56 ± 49.44 min vs. 181.47 ± 40.77 min; p < 0.01), significantly lower blood loss (116.67 ± 109.92 mL vs. 696.55 ± 519.43 mL; p < 0.01), and significantly shorter hospital stay (11.90 ± 9.69 vs. 25.35 ± 20.65; p < 0.01) than did the debulking group. No significant differences were observed between the groups in age, sex, spinal instability neoplastic score, ESCC, Tomita scores, numeric rating scale scores, American Spinal Injury Association Impairment Scale scores, survival rates, and complication rates. Postoperative neurologic function and decrease in pain were similar between the groups., Conclusion: The PPSF group had a shorter operation time, shorter length of hospital stay, and less blood loss than did the debulking group. PPSF followed by EBRT is pain relieving, relatively safe and appropriate as palliative therapy., Competing Interests: Conflicts of interest The authors have no financial or ethical conflicts of interest to report., (Copyright © 2021 Chang Gung University. Published by Elsevier B.V. All rights reserved.)

Background: Postoperative immunosuppression is associated with blood loss and surgical trauma during surgery and subsequently predisposes patients to increased morbidity. Spine endoscopic surgery has been accepted as an effective surgical technique with less surgical trauma and less blood loss for the complication of infectious spondylodiscitis. Therefore, the aim of this study was to investigate whether PEIDF could reduce the morbidity rates for patients with infectious spondylodiscitis. Methods: We launched a retrospective cohort study on the comparison of the perioperative prognosis between PEIDF and conventional open surgery for single-level lumbar infectious spondylodiscitis in patients with poor physical health (ASA ≥ 4) from 2014 to 2019. Results: Forty-four patients were included in this study. Fifteen of them underwent PEIDF, and the rest of the 29 patients were treated with open surgery. Less surgical blood loss (p < 0.001) and intraoperative transfusions (p < 0.001) with a better decline of CRP (p = 0.017) were statistically significant in patients receiving PEIDF. Patients undergoing conventional open surgery encountered more postoperative sepsis (p = 0.030), a higher qSOFA score (p = 0.044), and prolonged-time for CRP normalization (p = 0.001). Conclusions: PEIDF minimizes a poor postoperative outcome due to less surgical trauma, intraoperative blood loss, and the need for a blood transfusion.

Objective: Decreased bone mineral density as measured by dual-energy x-ray absorptiometry (DEXA) has been reported to be associated with cage subsidence following transforaminal lumbar interbody fusion (TLIF). However, DEXA is not often available or routinely performed before surgery. A novel MRI-based vertebral bone quality (VBQ) score has been developed and reported to be correlated with DEXA T-scores. The authors investigated the ability of the VBQ score to predict cage subsidence and other risk factors associated with this complication., Methods: In this retrospective study, the authors reviewed the records of patients who had undergone single-level TLIF from March 2014 to October 2015 and had a follow-up of more than 2 years. Cage subsidence was measured as postoperative disc height loss and was graded according to the system proposed by Marchi et al. The MRI-based VBQ score was measured on T1-weighted images. Univariable analysis and multivariable binary logistic regression analysis were performed. Ad hoc analysis with receiver operating characteristic curve analysis was performed to assess the predictive ability of the significant continuous variables. Additional analyses were used to determine the correlations between the VBQ score and T-scores and between the significant continuous variables and the amount of cage subsidence., Results: Among 242 patients eligible for study inclusion, 111 (45.87%) had cage subsidence after the index operation. Multivariable logistic regression analyses demonstrated that an increased VBQ score (OR 14.615 ± 0.377, p < 0.001), decreased depth ratio (OR 0.011 ± 1.796, p = 0.013), and the use of kidney-shaped cages instead of bullet-shaped cages (OR 2.766 ± 0.358, p = 0.008) were associated with increased cage subsidence. The VBQ score was shown to significantly predict cage subsidence with an accuracy of 85.6%. The VBQ score was found to be moderately correlated with DEXA T-scores of the total hip (r = -0.540, p < 0.001) and the lumbar spine (r = -0.546, p < 0.001). The amount of cage subsidence was moderately correlated with the VBQ score (r = 0.512, p < 0.001)., Conclusions: Increased VBQ scores, posteriorly placed cages, and kidney-shaped cages were risk factors for cage subsidence. The VBQ score was shown to be a good predictor of cage subsidence, was moderately correlated with DEXA T-scores for the total hip and lumbar spine, and also had a moderate correlation with the amount of cage subsidence.

(1) Background: Inexplicable low back and neck pain frequently results from spinal disc degeneration with an imbalanced intervertebral disc (IVD) cell homeostasis. We hypothesize that introducing MSC expressing a sustained cartilage-anabolic factor in the IVD may stimulate the mucoid materials secreted from the IVD cells, promote the MSC's chondrogenesis and maintain the hydration content providing mechanical strength to decelerate the disc degeneration progression; (2) Methods: This study expressed a cartilage-anabolic factor runx1 by a baculoviral vector (BV) transduced MSCs through a Cre/LoxP gene editing and recombination system for sustained recombinant runx1 transcription factor production. The Cre/LoxP BV modified MSCs were encapsulated by hyaluronan hydrogel, due to its' vital composition in ECM of a healthy disc and transplanted to a punctured coccygeal disc in rats through micro-injection, followed by X-ray radiography and histological analysis at the 4- and 12-weeks post-transplantation; (3) Results: Data reveals the Cre/LoxP BV system-mediated long-termed runx1 gene expression, possessing good biosafety characteristics in the in vitro cell transduction and in vivo MSCs transplantation, and maintained superior hydration content in the disc than that of mock transduced MSCs; (4) Conclusions: This proof-of-concept study fulfills the need of implanting therapeutic cells accompanied with microinjection in the disc, such as a discography and paves a road to manufacture composite hyaluronan, such as peptide modified hyaluronan as an MSC carrier for IVD regeneration in the future study.

The complex process of wound healing depends on the coordinated interaction between various immunological and biological systems, which can be aided by technology. This present review provides a broad overview of the medical applications of piezoelectric and triboelectric nanogenerators, focusing on their role in the development of wound healing technology. Based on the finding that the damaged epithelial layer of the wound generates an endogenous bioelectric field to regulate the wound healing process, development of technological device for providing an exogenous electric field has therefore been paid attention. Authors of this review focus on the design and application of piezoelectric and triboelectric materials to manufacture self-powered nanogenerators, and conclude with an outlook on the current challenges and future potential in meeting medical needs and commercialization., Competing Interests: No relevant financial or nonfinancial relationships., (© 2022 The Author(s). Published by National Institute for Materials Science in partnership with Taylor & Francis Group.)

Calvarial bone healing is challenging, especially for individuals with osteoporosis because stem cells from osteoporotic patients are highly prone to adipogenic differentiation. Based on previous findings that chondrogenic induction of adipose-derived stem cells (ASCs) can augment calvarial bone healing, we hypothesized that activating chondroinductive Sox Trio genes (Sox5, Sox6, Sox9) and repressing adipoinductive genes (C/ebp-α, Ppar-γ) in osteoporotic ASCs can reprogram cell differentiation and improve calvarial bone healing after implantation. However, simultaneous gene activation and repression in ASCs is difficult. To tackle this problem, we built a CRISPR-BiD system for bi-directional gene regulation. Specifically, we built a CRISPR-AceTran system that exploited both histone acetylation and transcription activation for synergistic Sox Trio activation. We also developed a CRISPR interference (CRISPRi) system that exploited DNA methylation for repression of adipoinductive genes. We combined CRISPR-AceTran and CRISPRi to form the CRISPR-BiD system, which harnessed three mechanisms (transcription activation, histone acetylation, and DNA methylation). After delivery into osteoporotic rat ASCs, CRISPR-BiD significantly enhanced chondrogenesis and in vitro cartilage formation. Implantation of the engineered osteoporotic ASCs into critical-sized calvarial bone defects significantly improved bone healing in osteoporotic rats. These results implicated the potential of the CRISPR-BiD system for bi-directional regulation of cell fate and regenerative medicine., Competing Interests: Declaration of interests The authors declare no competing interests., (Copyright © 2021 The American Society of Gene and Cell Therapy. Published by Elsevier Inc. All rights reserved.)

The formation of a nano-apatite surface layer is frequently considered a measure of bioactivity, especially for non-phosphate bioceramics. In the present study, strontium-doped calcium sulfate, (Ca,Sr)SO 4 , was used to verify the feasibility of this measure. The (Ca,Sr)SO 4 specimen was prepared by mixing 10% SrSO 4 by weight with 90% CaSO 4 ·½H 2 O powder by weight. A solid solution of (Ca,7.6%Sr)SO 4 was then produced by heating the powder mixture at 1100 °C for 1 h. The resulting (Ca,Sr)SO 4 specimen was readily degradable in phosphate solution. A newly formed surface layer in the form of flakes was formed within one day of specimen immersion in phosphate solution. Structural and microstructure-compositional analyses indicated that the flakes were composed of octacalcium phosphate (OCP) crystals. An amorphous interface containing OCP nanocrystals was found between the newly formed surface layer and the remaining (Ca,Sr)SO 4 specimen. The specimen was also implanted into a rat distal femur bone defect. In addition to new bone, fibrous tissue and inflammatory cells were found to interlace the (Ca,Sr)SO 4 specimen. The present study indicated that a more comprehensive evaluation is needed to assess the bioactivity of non-phosphate bioceramics. The newly formed surface layer on the (Ca,Sr)SO 4 specimen after soaking in phosphate solution for 28 days., (© 2021. The Author(s).)

An essential criterion for the selection of resorbable bioceramics is their ability to degrade inside human body within a reasonable time frame. Furthermore, if the bioceramic can release beneficial ions, such as strontium, as it degrades, recovery time might be shortened. The present study demonstrates that strontium-containing calcium sulfate (Sr,Ca)SO 4 can fulfill these criteria. A long-term in vitro degradation analysis for 12 weeks using sintered (Sr,Ca)SO 4 discs in phosphate buffered solution (PBS) was conducted. The sintered (Sr,Ca)SO 4 disc was then implanted into defects in the distal femur of rats. The degradation rate of (Sr,Ca)SO 4 discs showed a strong dependence on the Sr content. Similar results were observed between the long-term in vitro degradation analysis and the in vivo evaluation. The sintered (3.8%Sr,Ca)SO 4 disc lost more than 80% of its initial weight after soaking in PBS with shaking at 37 °C for 12 weeks. After 12 weeks in vivo, the remaining volume of the (3.8%Sr,Ca)SO 4 disc within the bone defect was ~25%. Over the same time period, new bone was formed at a relative volume of 40%. This study demonstrates the potential of (Sr,Ca)SO 4 bioceramic, and the benefits of using a long-term degradation test during the evaluation of resorbable bioceramics.