Search

The surface flow constructed wetland (SFCW) with Cyperus involucratus, Typha augustifolia and Thalia dealbata J. Fraser was applied to treat anaerobic treated-molasses wastewater (An-MWW) under the organic loading rates (OLRs) of 612, 696, 806, 929 and 1,213 kg BOD(5)ha(-1)day(-1). The results showed that both removal efficiency and plant growth rate were increased with the decrease of organic loading rate (OLR). All tested-plant species could not grow under OLR of higher than 696 kg BOD(5)mg l(-1) (p>0.05). Also, the plant-biomass of the systems was reduced by 10.4%, 26.5%, and 64.7% of initial plant-biomass under the OLR of 806, 929 and 1,213 kg BOD(5)ha(-1)day(-1), respectively. However, all tested-plant species showed the same pattern on the plant-biomass production yield and removal efficiency. The highest SS, BOD, COD, total phosphorus, NH(4)(+), NO(3)(-) and molasses pigments (MP) removal efficiencies of 90-93%, 88-89%, 67%, 70-76%, 77-82%, 94-95% and 72-77%, respectively were detected under the OLR of 612 kg BOD(5)ha(-1)day.

Among 2,402 strains of yeast isolated from various sources in Thailand, a strain No. SF9-246 identified as Issatchenkia orientalis, showed the highest potential for use in decolorization of molasses wastewater. In a malt extract-glucose-peptone broth (MYGP) culture containing melanoidin pigment (MP) at 30 degrees C a 60.2% decolorization was obtained within 7 days. The strain appeared to enhance both MP-degradation and MP-adsorption. The strain showed MP, chemical oxygen demand (COD) and biological oxygen demand (BOD(5)) removal efficiencies of 91.2%, 80.0% and 77.4%, respectively from anaerobic-treated molasses wastewater solution (T-MWW), collected from an anaerobic pond. The wastewater contained 2.5% glucose, 0.1% NH(4)Cl, and 0.1% KH(2)PO(4). The pH was adjusted to 5.0 at 30 degrees C for 7 days batch type culture system. The strain showed almost constant decolorization yield of 75-80% over 7 days in a periodical feeding system of 10% fresh T-MWW with the culture system. The strain provided a constant decolorization yield about 70% during 3 replacement cycles. Gel filtration chromatography showed that larger molecular weight fraction of MP solution was rapidly removed, while the smaller molecular weight fraction remained in the effluent.

In the analysis of food additives, past emphasis was put on the development of chromatographic techniques to separate target components from a complex matrix. Especially in the case of artificial food colors, direct spectrophotometric measurement was seen to lack in specificity due to a high spectral overlap between different components. Multivariate curve resolution (MCR) may be used to overcome this limitation. MCR is able to (i) extract from a complex spectral feature the number of involved components, (ii) attribute the resulting spectra to chemical compounds, and (iii) quantify the individual spectral contributions with or without a priori knowledge. We have evaluated MCR for the routine analysis of yellow and blue food colors in absinthe spirits. Using calibration standards, we were able to show that MCR equally performs as compared to partial least-squares regression but with much improved chemical information contained in the predicted spectra. MCR was then applied to an authentic collective of different absinthes. As confirmed by reference analytics, the food colors were correctly assigned with a sensitivity of 0.93 and a specificity of 0.85. Besides the artificial colors, the algorithm detected a further component in some samples that could be assigned to natural coloring from chlorophyll.

Azo dyes are of synthetic origin and their environmental fate is not well understood. They are resistant to direct aerobic bacterial degradation and form potentially carcinogenic aromatic amines by reduction of the azo group. This study shows that applying the oxidative processes of enzymatic treatment with laccase and ultrasound treatment, both alone and in combination, leads to dye degradation. Laccase treatment degraded both Acid Orange and Direct Blue dyes within 1-5 h but failed in the case of Reactive dyes, whereas ultrasound degraded all the dyes investigated (3-15 h). When applied as multi-stage combinations the treatments showed synergistic effects for dye degradation compared with individual treatments. Bulk light absorption (UV-Vis) and ion pairing HPLC were used for process monitoring. Additionally, mass spectrometry was used to elucidate the structures of intermediates arising from ultrasound treatment.

The Union of European Beverages Associations (UNESDA) has undertaken a screening exercise to determine whether any of the colours used in non-alcoholic beverages has the potential for high consumers to exceed the acceptable daily intake (ADI). The organisation undertook a survey of its membership to identify current use levels in non-alcoholic beverages. Information about the consumption of beverages and other foods that can contain the colours was derived from UK survey data because UK consumers were shown to represent some of the highest in the EU. A methodology was developed which added the intake of high level consumers of beverages to average intakes from all other uses to estimate total high level intake. A hierarchical approach used maximum approved use levels (where available) at the first tier and, if intakes exceed the ADI or maximum use levels were not available, UNESDA usage survey data at the second tier. Of the 33 colours approved for use in beverages nine were eliminated from further consideration at Tier 1. A further 22 colours were eliminated from further consideration at Tier 2. Two colours (E101 riboflavins and E110 sunset yellow) required further evaluation but under practical use conditions neither of these colours had the potential to exceed its ADI. Some colours used in beverages are permitted quantum satis in other foods and so permitted use levels were not available. Further information is required about these uses to determine whether total intakes from all foods have the potential to exceed ADIs.

A simple and sensitive on-chip preconcentration, separation, and electrochemical detection (ED) method for the electrophoretic analysis of food dyes was developed. The microchip comprised of three parallel channels: the first two are for the field-amplified sample stacking (FASS) and subsequent field-amplified sample injection (FASI) steps, while the third one is for the micellar EKC with ED (MEKC-ED) step. The food dyes were initially extracted from real samples by employing a method that was simpler, easier, and faster compared with a standard method. The extraction of the samples was characterized by UV-Vis and electrochemical experiments. The chronoamperometric detection was performed with a glassy carbon electrode coupled horizontally with the microchip at the separation channel exit. Experimental parameters affecting the analytical performance of the method were assessed and optimized. The sensitivity of the method was improved by approximately 10,800-fold when compared with a conventional MEKC-ED analysis. Reproducible response was observed during multiple injections of samples with an RSD of <7.2% (n=5). The calibration plots were linear (r2=0.998) within the range of 1.0 nM-1.0 microM for all food dyes. LODs were estimated between 1.0 and 5.0 nM, based on S/N=3, for food dyes. The applicability of the method for the analysis of food dyes in real sample was demonstrated.

Forty synthetic food colors were determined in drinks and candies by reversed-phase high-performance liquid chromatography with photodiode array detection. The following food colors were analyzed within 19 min using a short analytical column (50 mm x 4.6 mm i.d., 1.8 microm) at 50 degrees C with gradient elution: Ponceau 6R, Tartrazine, Fast yellow AB, Amaranth, Indigotine, Naphthol yellow S, Chrysoine, Ponceau 4R, Sunset yellow FCF, Red 10B, Orange G, Acid violet 7, Brilliant black PN, Allura red AC, Yellow 2G, Red 2G, Uranine, Fast red E, Green S, Ponceau 2R, Azorubine, Orange I, Quinoline yellow, Martius yellow, Ponceau SX, Ponceau 3R, Fast green FCF, Eosine, Brilliant blue FCF, Orange II, Orange RN, Acid blue 1, Erythrosine, Amido black 10B, Acid red 52, Patent blue V, Acid green 9, Phloxine B, Benzyl violet 4B, and Rose bengal. The recoveries of these compounds added to soft drinks and candies at 5 microg/g ranged from 76.6 to 115.0%, and relative standard deviations (R.S.D.s) were within 6.0%. The limits of detection and the limits of quantitation were 0.03 and 0.1 microg/g, respectively.

The results of French intake estimates for 13 food additives prioritized by the methods proposed in the 2001 Report from the European Commission on Dietary Food Additive Intake in the European Union are reported. These 13 additives were selected using the first and second tiers of the three-tier approach. The first tier was based on theoretical food consumption data and the maximum permitted level of additives. The second tier used real individual food consumption data and the maximum permitted level of additives for the substances which exceeded the acceptable daily intakes (ADI) in the first tier. In the third tier reported in this study, intake estimates were calculated for the 13 additives (colours, preservatives, antioxidants, stabilizers, emulsifiers and sweeteners) according to two modelling assumptions corresponding to two different food habit scenarios (assumption 1: consumers consume foods that may or may not contain food additives, and assumption 2: consumers always consume foods that contain additives) when possible. In this approach, real individual food consumption data and the occurrence/use-level of food additives reported by the food industry were used. Overall, the results of the intake estimates are reassuring for the majority of additives studied since the risk of exceeding the ADI was low, except for nitrites, sulfites and annatto, whose ADIs were exceeded by either children or adult consumers or by both populations under one and/or two modelling assumptions. Under the first assumption, the ADI is exceeded for high consumers among adults for nitrites and sulfites (155 and 118.4%, respectively) and among children for nitrites (275%). Under the second assumption, the average nitrites dietary exposure in children exceeds the ADI (146.7%). For high consumers, adults exceed the nitrite and sulfite ADIs (223 and 156.4%, respectively) and children exceed the nitrite, annatto and sulfite ADIs (416.7, 124.6 and 130.6%, respectively).

The number of cases using of forbidden dyes (such as Sudan-I and Para Red) in European foodstuff (including foodstuff from Russia) were increased last time. In this case it was required to adapt existing analytical methods for the control of dyes Sudan I-IV and Para Red. It was used for this purpose high performance liquid chromatography with detectings on diode-array and MS detector. Sudan I and Para Red were detected in 3 foodstuffs from examined 49 products. Concentration levels of these dyes were varied from 3 up to 500 mg/kg. Limits of determination of the methods is: HPLC-diode-array--0.1 mg/kg and HPLC-MS--0.5 mg/kg.

A method based on microchip electrophoresis with electrochemical (EC) detection has been developed for the simultaneous determination of Yellow AB, Red 2G, Sunset Yellow, New Coccine, and Amaranth which are azo-dyes frequently added to foodstuffs. Factors affecting both separation and detection processes were examined and optimized, with best performance achieved by using a 10 mM phosphate buffer (pH 11) as BGE solution and applying a voltage of 2500 V both in the separation and in the electrokinetic injection (duration 4 s). Under these optimal conditions, the target dye analytes could be separated and detected within 300 s by applying a detection potential of -1.0 V (vs. Ag/AgCl) to the glassy carbon (GC) working electrode. The recorded peaks were characterized by a good repeatability (RSD=1.8-3.2%), high sensitivity, and a wide linear range. Detection limits of 3.8, 3.4, 3.6, 9.1, 15.1 microM were obtained for Yellow AB, Red 2G, Sunset Yellow, New Coccine, and Amaranth, respectively. Fast, sensitive, and selective response makes the new microchip protocol very attractive for the quantitative analysis of commercial soft drinks and candies.

An accurate method based on the use of gel permeation chromatography (GPC)-liquid chromatography-tandem mass spectrometry interfaced with electrospray ionization (GPC-LC-ESI-MS/MS) was devised for the simultaneous determination of Sudan (I-IV), Sudan Orange G, Sudan Red B, Sudan Red G, Sudan Red 7B, Butter Yellow and Para Red in hot chili products. A GPC clean-up procedure was developed for simultaneous quantification of 10 dyes in hot chili and hot chili products avoiding some interference and permitting multiple injections without damaging the column. A HPLC was performed on an Inertsil C18 column using a multistep gradient elution with 0.1% formic acid and methanol as the mobile phase. Mass spectral acquisition was done in positive ion mode. Linearity of around three orders in the magnitude of concentration was generally obtained with the correlation coefficients (r2) of 0.9984-0.9997. Limit of detection (LOD) and limit of quantification (LOQ) for the investigated dyes were in the ranges of 0.1-1.8 and 0.4-5.0 microg/kg depending on matrices, respectively. The recoveries of the 10 synthetic dyes in five matrices ranged from 81.7 to 92.9%. The intra- and inter-day precision (RSDs) was between 2.9-7.8 and 3.9-8.1%, respectively. This method has been applied successfully for the determination of the studied 10 banned dyes in hot chili products.

A chemiluminescence method based on the luminol-H2O2 system with flow injection technology was proposed for the determination of sudan I in hot chilli sauce. It was found that sudan I could enhance chemiluminescence intensity generated from the luminol-H2O2 system. The increment of chemiluminescence intensity was proportional to the concentration of sudan I, giving a calibration graph linear over the concentration from 10 pg mL-1 to 7 ng mL-1 (R 2 = 0.9980) with the detection limit of 3 pg mL-1 (3sigma) and the quantification limit of 7.5 pg mL-1. At a flow rate of 2.0 mL min-1, one analysis cycle, including sampling and washing, could be accomplished in 60 s with a relative standard deviation of <5.0%. The method has been applied successfully to the determination of sudan I in Pixian douban, Golden Mark guilin chilli sauce, and Golden Mark satay sauce, and the recovery was 90.6-110.0%.

Carmine is one of the original dyes certified by the Biological Stain Commission (BSC). Until now it has lacked both an assay procedure for dye content and a means to positively identify the dye. The methods for testing carmine in the laboratory of the BSC have been revised to include spectrophotometric examination at pH 12.5-12.6 to determine that the dye is carmine (lambda(max)=530-335 nm). The maximum absorbance of a solution containing 100 mg of dye per liter of water, adjusted to pH 12.5-12.6, which provides a relative measure of dye content, should lie in the range 1.2 to 1.8. If the dye is not carmine, spectrophotometry at pH 1.9-2.1 shows whether it is carminic acid (lambda(max)=490-500 nm) or 4-aminocarminic acid (lambda(max)=525-530 nm). The latter two dyes, which are also called carmine when sold as food colorants, have physical properties different from those of true carmine. The functional tests for carmine as a biological stain are Orth's lithium-carmine method for nuclei, Southgate's mucicarmine method for mucus, and Best's carmine method for glycogen.

In polyethylene glycol 2000 (PEG)-(NH4)2SO4-edible pigment two-phase aqueous systems, the spectroscopic behaviour of the complexes of edible pigment and human serum albumin in PEG phase was investigated. Effects of different acidity, quantities of PEG and salt, reaction time, and coexistent matter on the determination of systems were discussed. Experimental results show that compared to BS spectra, the maximum wavelength of the complex of human serum albumin shifted to the red by 13 nm in buffer solution at pH 8, the maximum binding number of 40 was measured by molar ratio method, and the apparent molar absorptivity was 9.4 x 10(4) L x mol(-1) x cm(-1). The linear range was 0-21.07 mg x L(-1). With different surfactant, the interaction mechanism of protein and edible pigment was discussed.

A reversed-phase high performance liquid chromatographic method for the successful separation and determination of 13 synthetic food colorants (Tartrazine E 102, Quinoline Yellow E 104, Sunset Yellow E 110, Carmoisine E 122, Amaranth E 123, Ponceau 4R E 124, Erythrosine E 127, Red 2G E 128, Allura Red AC E 129, Patent Blue V E 131, Indigo Carmine E 132, Brilliant Blue FCF E 133 and Green S E 142) was developed. A C18 stationary phase was used and the mobile phase contained an acetonitrile-methanol (20:80 v/v) mixture and a 1% (m/v) ammonium acetate buffer solution at pH 7.5. Successful separation was obtained for all the compounds using an optimized gradient elution within 29 min. The diode-array detector was used to monitor the colorants between 350 and 800 nm. The method was thoroughly validated. Detection limits for all substances varied between 1.59 (E 142) and 22.1 (E 124) microg L(-1). The intra-day precision (as R.S.D.(r)) ranged from 0.37% (E 122 in fruit flavored drink at a concentration of 100 mg L(-1)) to 4.8% (E 142 in icing sugar at a level of 0.9 mg kg(-1)). The inter-day precision (as R.S.D.(R)) was between 0.86% for E 122 in fruit flavored drink at 100 mg L(-1) and 10% for E142 in jam at a concentration of 9 mg kg(-1). Satisfactory recoveries, ranging from 94% (E 142 in jam) to 102% (E 131 in sweets), were obtained. The method was applied to the determination of colorants in various water-soluble foods, such as fruit flavoured drinks, alcoholic drinks, jams, sugar confectionery and sweets, with simple pre-treatment (dilution or water extraction).

This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, including flavouring agents, with a view to recommending acceptable daily intakes (ADIs) and to preparing specifications for identity and purity. The Committee also evaluated the risk posed by two food contaminants, with the aim of advising on risk management options for the purpose of public health protection. The first part of the report contains a general discussion of the principles governing the toxicological evaluation and assessment of intake of food additives (in particular flavouring agents) and contaminants. A summary follows of the Committee's evaluations of technical, toxicological and intake data for certain food additives (acidified sodium chlorite, asparaginase from Aspergillus oryzae expressed in Aspergillus oryzae, carrageenan and processed Eucheuma seaweed, cyclotetraglucose and cyclotetraglucose syrup, isoamylase from Pseudomonas amyloderamosa, magnesium sulfate, phospholipase A1 from Fusarium venenatum expressed in Aspergillus oryzae, sodium iron(III) ethylenediaminetetraacetic acid (EDTA) and steviol glycosides); eight groups of related flavouring agents (linear and branched-chain aliphatic, unsaturated, unconjugated alcohols, aldehydes, acids and related esters; aliphatic acyclic and alicyclic terpenoid tertiary alcohols and structurally related substances; simple aliphatic and aromatic sulfides and thiols; aliphatic acyclic dials, trials and related substances; aliphatic acetals; sulfur-containing heterocyclic compounds; aliphatic and aromatic amines and amides; and aliphatic alicyclic linear alpha, beta -unsaturated di- and trienals and related alcohols, acids and esters); and two food contaminants (aflatoxin and ochratoxin A). Specifications for the following food additives were revised: maltol and ethyl maltol, nisin preparation, pectins, polyvinyl alcohol, and sucrose esters of fatty acids. Specifications for the following flavouring agents were revised: maltol and ethyl maltol, maltyl isobutyrate, 3-acetyl-2,5-dimethylfuran and 2,4,5-trimethyl-delta-oxazoline (Nos 1482, 1506 and 1559), and monomenthyl glutarate (No. 1414), as well as the method of assay for the sodium salts of certain flavouring agents. Annexed to the report are tables summarizing the Committee's recommendations for intakes and toxicological evaluations of the food additives and contaminants considered.

The brief information on existing official methods of research of food dyes in food stuffs in the various countries are given. The special attention is given to a urgency of development of methods of extraction of food dyes from the complex foodstuff containing carbohydrates. In article are given the data on frequency of use of various kinds of food dyes in the food-processing industry of Russia.

Exogenous pigments produced by ascomycetous filamentous fungi belonging to the genera Penicillium, Epicoccum, and Monascus, preselected based on chemotaxonomic knowledge, have been extracted and characterized by quantitative colorimetry. The color characteristics of the fungal extracts were compared to water soluble natural colorants derived from sources currently in use. The tested fungal extracts also included some commercially available Monascus colorants. The a values for the fungal extracts were found to be both positive and negative, the b values were found to be positive, while the hue angles of the fungal color extracts ranged from 40 to 110 indicating the color distribution of fungal extracts over the red-orange-yellow region of the CIELAB color space. The fungal extracts exhibited additional color hues in the red spectrum and similar hues in the yellow spectrum as compared to the reference natural colorants. They were also found to be similar or brighter in terms of chroma to some of the reference natural colorants. Principal component analysis was performed to group and distinguish different colors based on the a and b values. The fungal color extracts could be grouped in accordance with the similarity or difference in the color to those of the existing natural colorants. The diversity of colors was not only found among different fungal genera and/or species but also within the same species on changing the media. There was a marked change in the color composition of the extracts resulting in relatively different hues. Our results, thus, indicate that there exists pigment-producing genera of ascomycetous fungi other than Monascus that produce color shades in the red and the yellow spectra in addition or similar to reference colorants. These color shades could add to the color palette of the natural colorants currently in use. In addition, the multivariate approach in distinguishing and classifying the colorants was shown to be a very useful tool in colorimetric comparison of colorants.

Classification of isolates into mycelial compatibility groups (MCGs) is used routinely in many laboratories as a quick marker for genotyping Sclerotinia sclerotiorum within populations. Scoring each new sample requires optimization of standardized conditions to support adequate growth of all paired isolates. Appropriate conditions for growth are especially important because diverse compatibility reactions are difficult to categorize and score (e.g., in samples from populations with high genetic diversity, such as those that receive immigration from genetically diverse sources or those that deviate from strict clonality). The current standard medium for MCG testing can be inhibitory to isolates from some samples, confounding scoring of compatibility. We identified two foci for optimization: (i) choice of medium, in this experiment, Patterson's medium amended with red food coloring (termed modified Patterson's medium, MPM, the current standard medium) versus potato dextrose agar (PDA) and (ii) amount of McCormick's red food coloring amended to the growth medium. The red food coloring often yields a red reaction line in incompatible interactions; alternative incompatible reactions are a line of thick or thin hyphae. Based on results to date, self-self pairings of S. sclerotiorum are compatible and are a reliable standard for scoring compatible self-nonself mycelial interactions. PDA amended with 75 microl/L of McCormick's red food coloring was identified as optimal for isolates inhibited by MPM from a highly diverse, recombining population sample. This precisely amended PDA was also suitable for isolates from highly clonal populations that were not inhibited by MPM or by higher concentrations of red food coloring. Under the optimized, standardized conditions all paired isolates grew together and produced interactions that could be scored in repeatedly identifiable categories, compatible or incompatible. Workers are advised to optimize conditions before screening a new population sample.

To assess the intake of artificial food colour additives by 5-14-year-old children in the State of Kuwait, a 24-h dietary recall was conducted twice on 3141 male and female Kuwaiti and non-Kuwaiti children from 58 schools. The determination of colour additives in 344 foods items consumed was performed using high-performance liquid chromatography with diode array detector. A comparison with the Food and Agriculture Organization and World Health Organization acceptable daily intakes (ADIs) was undertaken to evaluate the potential risk associated with the consumption of artificial colour additives by children in Kuwait. The results indicated that out of nine permitted colours, four exceeded their ADIs by factors of 2-8: tartrazine, sunset yellow, carmoisine and allura red. Further, follow-up studies to provide insight into potential adverse health effects associated with the high intakes of these artificial colour additives on the test population are warranted.

An accurate method was developed for the simultaneous determination of water-Tartrazine, Amaranth, Ponceau 4R, Sunset Yellow FCF, and fat-Sudan (I-IV), synthetic soluble colorants in foodstuff. This method uses dimethylsulfoxide (DMSO) as the extraction solvent in the sample preparation process and high performance liquid chromatography (HPLC)-diode array detector (DAD)-electrospray mass spectrometry (ESI-MS), applying selected ion recording in positive/negative alternate mode to acquire mass spectral data, as the analytical technique. Linearity of around three orders in the magnitude of concentration was generally obtained. Detection and quantification limits of the investigated dyes, which were evaluated at signal to noise ratio of 3 for detection limit and 10 for quantification limit, were in the ranges of 0.01-4 and 0.03-11.2 ng, respectively. The recoveries of the eight synthetic colorants in four matrices ranged from 93.2 to 108.3%. Relative standard deviations of less than 8.2% were also achieved. This method has been applied successfully in the determination of water-soluble colorants in the soft drink and the delicious ginger, and fat-soluble dyes in chilli powders and chilli spices.

The methodical approach by definition of food dyes in a composition of complex food additives is realized. Research of 98 samples of complex food additives is shown, that realization of research of their composition is necessary for the control of observance of hygienic norms on application of food dyes. In result of qualitative and quantitative research of food dyes in composition, it was revealed, that 3.1% from number of the investigated samples there does not correspond the declaration of a composition, 7.1%--do not correspond to the declared scope, for 2% of products corrective amendments were brought in a recommended dosage in an end-product.

The alcoholic beverage absinthe is recently experiencing a revival after a yearlong prohibition. This review article provides information on all aspects of this bitter spirit and its major components, especially wormwood (Artemisia absinthium L.), which contains the toxic monoterpene thujone. Over 100 references on historic and current literature are provided. The topics comprise the history of the alcoholic drink starting from its invention in the eighteenth century. Historical and modern recipes are discussed in the context of different quality categories and possibilities to reduce the content of thujone are given. The analytical techniques used to verify compliance with the maximum limit of thujone as well as further possibilities for quality control of absinthe are discussed. The toxicology of absinthe is reviewed with regard to the cause of a syndrome called "absinthism," which was described after chronic abuse of the spirit in the nineteenth century. Finally, a food regulatory and food chemical evaluation is provided and minimum requirements for absinthe are suggested. Absinthe should have a recognizable wormwood flavor and after dilution with water the characteristic clouding should arise (louche-effect). Products, which are advertized as being of premium grade should be made by distillation, should have an alcoholic strength of at least 45%vol, and should not contain artificial dye.

As foodstuffs adulterated by illegal dyes, such as Sudan I, II, III IIV, para-Red, have appeared on the European Union market, the emergency measures to eliminate this problem have been taken. The illegal dyes are added to dried, ground chilli, curry, curcuma and to palm oil. These products are imported from countries outside the E.U. The adulteration concerns also ready to eat products which contain the ingredients mentioned above. Apart from the adulteration, the presence of illegal dyes in foodstuffs can be a threat to consumer's health. In 2003-2005 three Commission Decisions on emergency measures regarding some products which can contain illegal dyes were published. Since May 2003 to March 2006, 651 notifications on food adulteration by illegal dyes were sent to the RASFF system. As a result of the taken measures, the number of notifications have decreased. The possibility of food adulteration by illegal dyes different from the ones which are used now are considered. This is the reason why the continuation of food control and cooperation between official control authorities and food producers are necessary.

Dunaliella carotene, extracted from dunaliella alga (Dunaliella bardawil or Dunaliella salina), for use as a food-coloring agent, has beta-carotene as its mainly constituent. As there have been no reports of toxicological evaluation, a 90-day subchronic toxicity study was here performed in F344 rats at dose levels of 0 (control), 0.63%, 1.25%, 2.5% and 5% in powdered basal diet. The average daily intakes of dunaliella carotene were 352, 696, 1420 and 2750 mg/kg/day, respectively, for males, and 370, 748, 1444 and 2879 mg/kg/day for females. No mortality or treatment-related clinical signs were observed throughout the experimental period in any of the groups. Body weight gain was slightly but significantly (p < 0.05) reduced from week 5 to the end of the experiment in 2.5% and 5% males. Increased PLT were observed in 1.25% and 5% males, and 2.5% and 5% females. Significant elevations or tendencies for increase in serum T. Cho and Ca were observed in all treated males and females, with clear dose-dependence in males. Organ weight measurement and histopathological observation revealed no toxicological changes. Based on growth suppression, no-observed-adverse-effect-levels (NOAELs) were estimated to be 1.25% (696 mg/kg/day) for males and 5% (2879 mg/kg/day) for females. As increases in serum Ca were observed in the lowest group in both sexes, a no-observed-effect level (NOEL) could not be determined in this study.

An analytical method using high performance liquid chromatography with photodiode array and fluorescence detection has been developed and applied to the determination of the food colour additives copper chlorophylls and copper chlorophyllins (E141[i] and [ii]) in foods and beverages. The analytical procedures from previously reported methods have been refined to cover a range of food colour formulations and retail foods. The method was single-laboratory validated. Recoveries of the polar copper chlorophyllins from spiked samples (at 14.5 mg/kg in all but one case) were in the range 79-109%, except for jelly sweets (49%). Recoveries of relatively non-polar copper chlorophylls were in the range 77-107% (except for 'made' jelly at 50%). The %RSD for recoveries was generally below 12%. Quantitative estimates of the total copper chlorophyll/chlorophyllin content of a small range of food commodities are reported, based on the use of trisodium copper chlorophyllin as a surrogate standard. The majority of E141-containing foods and colour formulations analysed exhibited a multiplicity of components due to the various extraction and purification processes that are used to obtain these colour additives. This was confounded by the presence of overwhelming amounts of native chlorophylls in certain samples (e.g. mint sauce). Food commodities containing significant amounts of emulsifiers (i.e. ice cream), gelatine or fats were problematic during extraction hence further development of extraction regimes is desirable for such products. All of the samples analysed with added E141, had estimated total copper chlorophyllin contents of below 15 mg/kg (range 0.7-13.0).

Square wave (SW) voltammetry was used to explore the adsorption properties of the food additive dye Allura Red on a hanging mercury drop electrode (HMDE). By using the adsorptive stripping voltammetric approach, we developed a sensitive electroanalytical method for the determination of this azo dye. A well-developed voltammetric peak probably related to the cathodic reduction of the azo moiety was obtained in pH 9 Britton-Robinson (B-R) buffer at 613 mV. Cyclic voltammetric studies indicated that the reduction process was irreversible and primarily controlled by adsorption. The adsorptive voltammetric signal was evaluated with respect to various experimental conditions; the optimized values were supporting electrolyte, B-R buffer; pH 11; accumulation time, 180 s; accumulation potential, 0.0 V; scan rate, 900 mV/s; pulse amplitude, 75 mV; and SW frequency, 90 Hz. Adsorptive voltammetric peak current showed a linear response for Allura Red in the concentration range of 2.5 x 10(-8) to 2.0 x 10(-7) mol/L (r = 0.998). The limit of detection was 8.5 x 10(-9) mol/L (4.2 ng/mL), the precision in terms of relative standard deviation was 1.3%, and the mean recovery was 102%. Possible interferences by several substances usually present in food products such as food additive azo dyes (E110, E102), gelatin, natural and artificial sweeteners, preservatives, and antioxidants were also evaluated. The proposed electrochemical procedure was successfully applied to the determination of this food dye in commercially available candy and a soft drink. The results were compared by statistical evaluation with those obtained by a reference spectrophotometric method.

This article reports on the first application of a modified version of the bilinear least-squares model to absorbance-pH second-order data recorded for complex samples. The latter are composed of fruit drink powders, where four different analytes and additional background components occur. The analytes are the common juice colorants tartrazine, yellow sunset, allura red and indigo carmine. The data have been measured after generating a double pH gradient within a flow injection system. The selected chemometric methodology adequately exploits the second-order advantage, needed to take into account the background interferents present in real samples. Due to severe spectral overlapping between the acid and basic forms of each of the colorants in the working pH range, other second-order multivariate calibration methods such as parallel factor analysis and multivariate curve resolution-alternating least-squares could not be successfully applied to the presently studied samples. Recoveries of 94.8, 104.7, 109.3 and 105.3% were obtained for yellow sunset, indigo carmine, allura red and tartrazine respectively in the real test samples.

Carmine is one of the few dyes currently certified by the Biological Stain Commission that is not assayed for dye content. Existing assay methods are complex and do not differentiate the three cochineal derivatives carmine, carminic acid and aminocarminic acid. The latter dye is relatively new to the food trade as an acid-stable red colorant and may eventually enter the biological stains market. The assay proposed here is a two-step procedure using quantitative spectrophotometric analysis at high pH (12.5-12.6) followed by a qualitative scan of a low pH (1.90-2.10) solution. Carmine is distinct at high pH, and the remaining dyes are easily distinguished at low pH. Four instances of mislabeling are documented from 18 commercial products, but the mislabeled dyes were not certified dyes. Samples from nearly all lots of carmine certified by the Biological Stain Commission from 1920 to 2004 proved to be carmine, but they varied widely in dye content. Batches from 1920 through the 1940s were significantly richer in dye content. Variability has been extreme since 2000, and most of the poorest lots have been submitted since 1990.

This collaborative study was conducted to determine the total monomeric anthocyanin concentration by the pH differential method, which is a rapid and simple spectrophotometric method based on the anthocyanin structural transformation that occurs with a change in pH (colored at pH 1.0 and colorless at pH 4.5). Eleven collaborators representing commercial laboratories, academic institutions, and government laboratories participated. Seven Youden pair materials representing fruit juices, beverages, natural colorants, and wines were tested. The repeatability relative standard deviation (RSDr) varied from 1.06 to 4.16%. The reproducibility relative standard deviation (RSDR) ranged from 2.69 to 10.12%. The HorRat values were < or = 1.33 for all materials. The Study Director recommends that the method be adopted Official First Action.

A screening method for the detection of artificial colours (naphthol yellow, tartrazine, quinoline yellow, Sunset yellow, Allura red, amaranth, azorubine, Ponceau 4R and Red 2G) in saffron is described. The method involves removal of crocins by precipitation of crocetin (pH 0.1, 90 degrees C) before adsorption of the artificial colours on polyamide SPE cartridges (pH 2). After washing with methanol, acetone and methanol, elution was done with a methanol:ammonia solution (95:5 v/v), and detection was performed by derivative spectrometry. Sample pretreatment changes the UV-Vis saffron extract profile in such a way that second derivative spectra can be used to identify the presence of added colours. Erythrosine, which was found to be pH dependent, could not be detected under the above conditions. The lowest detectable amount for each colour was strongly dependent on chemical structure. The recovery of carminic acid was very low possibly due to irreversible retention on the polyamide. This procedure can replace the current ISO TLC method (2003) and be used alternatively or in combination with HPLC procedures adopted in the same standard.

Photoacoustic (PA) spectroscopy in the visible wavelength region was shown to be suitable for a direct (no preparatory steps involved) quantification of sunset yellow (E110) colour in effervescent multi-vitamin tablets. Measurements on powdered tablets containing E110 were performed at 480 nm at which wavelength this synthetic colour shows appreciable absorbance. The PA data obtained were compared to the results acquired by diffuse reflectance spectroscopy and conventional spectrophotometry. Intrinsic simplicity, ease of sampling and rapid response were the most important advantages of the PA technique. In terms of sensitivity the performance of the three methods were comparable.

CFR and JECFA specify that the total color in FD&C Blue No. 2 (B2; Indigo Carmine, Indigotine, Food Blue No. 2) is not less than 85%, its isomer (B2iso) in B2 is not more than 18%, and its subsidiary color (B2sub) in B2 is not more than 2% (CFR) or 1% (JECFA). Japan's Specifications and Standards for Food Additives, 7th Edition, specifies that the total color in B2 is not less than 85.0% and other color materials in B2 are not detected by paper chromatography. LC/MS and HPLC were employed to identify and determine the main component (B2m) of B2, B2iso, and B2sub. The pseudo molecular ions (B2m and B2iso: [M-2Na+H]-, m/z=421; B2sub: [M-Na]-, m/z=341) of each color material were obtained and identified by LC/MS based on their absorptions and mass spectra. The contents of B2iso and B2sub in B2 samples (certified samples from fiscal year 1998 to fiscal year 2002) were determined by HPLC using calibration curves for the standards of B2m and B2iso. The contents of B2iso in most samples were less than 10%, and the contents of B2sub in all samples were not more than 1%. All of them were within the regulatory limits set by the CFR and JECFA.

Desorption electrospray ionization (DESI) was demonstrated as a means to couple thin-layer chromatography (TLC) with mass spectrometry. The experimental setup and its optimization are described. Development lanes were scanned by moving the TLC plate under computer control while directing the stationary DESI emitter charged droplet plume at the TLC plate surface. Mass spectral data were recorded in either selected reaction monitoring mode or in full scan ion trap mode using a hybrid triple quadrupole linear ion trap mass spectrometer. Fundamentals and practical applications of the technique were demonstrated in positive ion mode using selected reaction monitoring detection of rhodamine dyes separated on hydrophobic reversed-phase C8 plates and reversed-phase C2 plates, in negative ion full scan mode using a selection of FD&C dyes separated on a wettable reversed-phase C18 plate, and in positive ion full scan mode using a mixture of aspirin, acetaminophen, and caffeine from an over-the-counter pain medication separated on a normal-phase silica gel plate.

A microemulsion electrokinetic chromatography (MEEKC) method was developed to analyze and detect eight food colorants (tartrazine, fast green FCF, brilliant blue FCF, allura red AC, indigo carmine, sunset yellow FCF, new coccine, and carminic acid), which are commonly used as food additives in various food products. The effects of sodium dodecyl sulfate (SDS) surfactant, organic modifier, cosurfactant, and oil were examined in order to optimize the separation. The amount of organic modifier (acetonitrile) and SDS surfactant were determined as apparent influences on the separation resolution while the type of oil and cosurfactant rarely affected the separation selectivity of the eight colorants. A highly efficient MEEKC separation method, where the eight colorants were separated with baseline resolution within 14 min, was achieved by using a microemulsion solution of pH 2.0 containing 3.31% SDS, 0.81% octane, 6.61% 1-butanol, and 10% acetonitrile. This optimal MEEKC method has a higher separation efficiency and similar detection limit when compared to conventional capillary electrophoresis (CE) method. Furthermore, a sample pretreatment is rarely needed when this MEEKC technique is used to analyze colorants in food products, whereas a suitable sample pretreatment (for example solid-phase extraction) has to be employed prior to CE separation in order to eliminate matrix interferences resulting from the constituents of the food sample.

A simple and rapid method is reported for the routine determination 1-phenylazo-2-naphthol (Sudan I) in chilli powder and in chilli-containing food products. The method involved Soxtec extraction from the products followed by high-pressure gel permeation chromatographic clean-up collecting the appropriate fraction. Analysis of this fraction was by HPLC with UV/VIS detection. The limit of detection was 7 microg kg(-1) and the limit of quantification was 13 microg kg(-1). The identity of Sudan I in food products was established by electrospray LC/MS with MS/MS confirmation. From a small survey of 30 retail samples, 11 samples of crushed chilli, Italian pasta, chilli-snack and vegetable sauce contained levels of Sudan I ranging from 24 to 5591 microg kg(-1).

Japan's Specifications and Standards for Food Additives, 7th Edition (JSFA-VII) does not set limits for total contents of water-soluble chlorides and water-soluble sulfates (water-soluble inorganic salts) in food color aluminum lakes (FC-Als). However, the regulatory limit is 2% in JECFA and CFR. We used column switching suppressor-type ion chromatography (CSS-IC) for determination of anions. The total contents of water-soluble inorganic salts in FC-Als (112 qualified samples) were determined using the modified CSS-IC from fiscal year 1998 to fiscal year 2003. Total contents of water-soluble inorganic salts in four samples exceeded 2%. From an international point of view, it is desirable that the total content of water-soluble inorganic salts in FC-Al should again be regulated in Japan.

An accurate method based on the use of reversed-phase (RP) liquid chromatography-tandem mass spectrometry interfaced with electrospray (LC-ESI-MS/MS) was devised for the determination of Sudan I, Sudan II, Sudan III and Sudan IV in hot chilli food samples. A simple sample treatment procedure entailing the use of an extraction step with acetone without clean-up was developed. A C18 column with an aqueous formic acid/methanol mixture as the mobile phase was used under isocratic conditions. Mass spectral acquisition was done in positive ion mode by applying selected reaction monitoring of three fragmentation transitions per compound to provide a high degree of selectivity. The method was in-house validated in terms of detection limits (LOD), quantitation limits (LOQ), linearity, sensitivity, accuracy, recovery, and selectivity on two kinds of hot chilli sauces. Good results in the low ng/g level were obtained for LOD and LOQ of all analytes in matrices. Under both intra-day repeatability (R.S.D. between 1 and 13%) and intermediate precision (about 5-15% R.S.D. for both chilli sauce matrices) conditions, precision proved to be typical of determinations based on electrospray LC-MS and acceptable for routine monitoring purposes. Extraction recoveries for all four azo-dyes in chilli tomato sauce ranged from 92 to 103% at a spiking level of 5 microg/kg, whereas values between 72 and 97% were calculated in chilli tomato and cheese sauce at the same concentration level. The applicability of the method to the determination of Sudan azo-dyes in hot chilli products was demonstrated.

A method for the determination of 12 synthetic food dyes (Amaranth, Erythrosine, Allura Red AC, New Coccine, Phloxine, Rose Bengal, Acid Red, Tartrazine, Sunset Yellow FCF, Fast Green FCF, Brilliant Blue FCF, Indigo Carmine) in food was developed using capillary electrophoresis (CE) with photodiode array detection. The dyes were extracted with water and 0.5% ammonia-ethanol (1:1) mixture, and cleaned up using solid-phase extraction (Sep-Pak Plus tC18). The dyes were eluted with methanol from the cartridge. The dyes were separated by CE on a bubble cell fused-silica capillary (72 cm to the detector, 75 microm i.d.) using 20% acetonitrile in a mixture of 10 mmol/L potassium phosphate, monobasic and 5 mmol/L sodium carbonate (pH 10.0) as the running buffer. Identifications of the dyes were performed on the basis of the migration time and the absorbance spectrum of each peak. The coefficients of variation of the migration times and the peak areas were 0.28-0.62% and 1.84-4.30%, respectively (n = 5). The identification limits using the absorbance spectra of the dyes were 10 microg/mL for Brilliant Blue FCF and Fast Green FCF, and 5 microg/mL for the other 10 dyes. The recoveries of the 12 dyes from pickles, soft drinks and candies at the level of 10 microg/g were 70.0-101.5%. The method was applied to the analysis of dyes in foods. The dyes detected by CE were in agreement with those detected by paper chromatography.

An exposure assessment of synthetic food colours was carried out among 1-5- and 6-18-year-old individuals by the food frequency method. Children had an intake of solid food consumption in the range 2-465 g day(-1) and liquid food consumption in the range 25-840 ml day(-1) with added colours. Among the eight permitted colours in India, six were consumed by the subjects of the study. The intakes of some subjects exceeded the acceptable daily intake for colours such as tartrazine, sunset yellow and erythrosine, which is 7.5, 2.5 and 0.1 mg kg(-1) body weight, respectively. Therefore, a uniform permissible limit of 100 mg kg(-1) prescribed under the Prevention of Food Adulteration Act in India for all foods is not justified. The limits need to be revised according to the Codex Alimentarius Commission, which permits different maximum levels of additives to various food categories based on both the extent of consumption and the technological justification for its use.

The differences in color coordinates obtained from the use of different spectral features in the calculation are studied. Seven groups of food (olive oil, vanilla milkshake, brandy, honey, grape juice, vinegar, and orange juice) and an anthocyanin petunidin solution (natural pigment present in several vegetables) with different pH values were selected. Tristimulus values were calculated by considering the different sources of errors (truncation, abridgement, or different bandwidths). Results obtained were corrected by using the methods recommended (see References). These methods of abridgment work well in general, although in some circumstances (20 nm bandwidth or larger), specific spectral weighting functions have to be used to obtain a negligible error. Therefore, it is interesting to know how much difference can be expected from those factors in order to avoid confusion between color differences attributable to instruments and those attributable to actual color changes.

A simple method has been developed for the extraction, separation, and determination of synthetic colors in ice cream samples. The process involves the breakdown of emulsion by neutral detergents (Triton X-100 and Tween 20) followed by extraction with petroleum ether for removal of fat. The aqueous colored solution obtained is treated with 5% acetic acid, and the uptake of color is carried out by a wool-dyeing technique. The color is eluted from the wool with 5% ammonia solution, the solution is evaporated to dryness, and the residue is dissolved in 60% ethanol for paper chromatography using trisodium citrate-ammonia-water (2 + 5 + 95, w/v/v) as the mobile phase. The colored spots from the paper chromatogram are cut and eluted with 60% ethanol, and the absorbance is measured at the respective lambda maximum corresponding to the Rf value of the appropriate standard. The recoveries of 6 colors, including sunset yellow FCF (SSYFCF), tartrazine, carmoisine, ponceau 4R, brilliant blue FCF (BBFCF), and fast green FCF from spiked samples with either detergent were found to be >90%. However, recoveries of erythrosine were 21 and 65% with Triton X-100 and Tween 20, respectively. Indigo carmine could not be recovered at all because of its fugitive property in 5% ammonia solution, which is used to strip the color from the wool. The sensitivity of the method with the use of Tween 20 is 1 ppm (1 microg/g) for the colors in spiked ice cream samples. With this method, we analyzed samples of 20 branded colored ice cream. The results showed the presence of tartrazine (8.4-43.3 ppm), SSYFCF (23.5-117.6 ppm), carmoisine (traces-53.2 ppm), erythrosine (3.5 ppm), and BBFCF (4.1 ppm) in the ice cream samples. Apart from 2 samples of tuttifruity, all of the ice cream samples showed the presence of permitted synthetic colors below the permissible level of 100 ppm established by the Prevention of Food Adulteration Act of India.

The commercial value of a cochineal (Dactylopius coccus Costa) sample is associated with its color quality. Because the cochineal is a legal food colorant, its color quality is generally understood as its pigment content. Simply put, the higher this content, the more valuable the sample is to the market. In an effort to devise a way to measure the color quality of a cochineal, the present study evaluates different parameters of color measurement such as chromatic attributes (L*, and a*), percentage of carminic acid, tint determination, and chromatographic profile of pigments. Tint determination did not achieve this objective because this parameter does not correlate with carminic acid content. On the other hand, carminic acid showed a highly significant correlation (r = - 0.922, p = 0.000) with L* values determined from powdered cochineal samples. The combination of the information from the spectrophotometric determination of carminic acid with that of the pigment profile acquired by liquid chromatography (LC) and the composition of the red and yellow pigment groups, also acquired by LC, enables greater accuracy in judging the quality of the final sample. As a result of this study, it was possible to achieve the separation of cochineal samples according to geographical origin using two statistical techniques: cluster analysis and principal component analysis.

There is considerable interest in determining the added levels of the natural dye annatto in foods like snack products, particularly because they are mostly consumed by young people. The objective was to use response surface methodology to develop a new method to analyse annatto in extruded snacks. A pretreatment of the samples was necessary, digesting the ground sample with alpha-amylase at room temperature. The pigment was extracted by shaking with ethyl acetate at room temperature, eight extractions being necessary for completion extract the pigment. Lipids were removed by alkaline saponification. Under these conditions, 100% of the bixin was converted into norbixin, which was then quantified by high-performance liquid chromatography. The method had a mean recovery of 97% and a coefficient of variation for duplicate analysis of 1%. Using this method, of the 13 commercial samples analysed, a parmesan cheese-flavoured snack product showed the highest level of dye expressed as norbixin (15.5 mg kg(-1)), whilst other brands of onion-flavoured snack products had the lowest levels (0.7 and 0.4 mg kg(-1), respectively).

This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various food additives, with a view to recommending acceptable daily intakes (ADIs) and to prepare specifications for the identity and purity of food additives. The first part of the report contains a general discussion of the principles governing the toxicological evaluation of food additives (including flavouring agents) and contaminants, assessments of intake, and the establishment and revision of specifications for food additives. A summary follows of the Committee's evaluations of toxicological and intake data on various specific food additives (alpha-amylase from Bacillus lichenformis containing a genetically engineered alpha-amylase gene from B. licheniformis, annatto extracts, curcumin, diacetyl and fatty acid esters of glycerol, D-tagatose, laccase from Myceliophthora thermophila expressed in Aspergillus oryzae, mixed xylanase, beta-glucanase enzyme preparation produced by a strain of Humicola insolens, neotame, polyvinyl alcohol, quillaia extracts and xylanase from Thermomyces lanuginosus expressed in Fusarium venenatum), flavouring agents, a nutritional source of iron (ferrous glycinate, processed with citric acid), a disinfectant for drinking-water (sodium dichloroisocyanurate) and contaminants (cadmium and methylmercury). Annexed to the report are tables summarizing the Committee's recommendations for ADIs of the food additives, recommendations on the flavouring agents considered, and tolerable intakes of the contaminants considered, changes in the status of specifications and further information requested or desired.

The back propagation artificial neural network was applied to process spectrophotometric data of mixed colorants. By optimizing the network structure and parameters, the predication accuracy was enhanced. The method was used for simultaneous determination of mixed colorants in synthetic samples and drinks on sale with satisfactory results. Therefore, the artificial neural network may provide a new approach to determine the mixed colorants is drinks by spectrophotometry without any preliminary chemical separation.

A technique combining an on-capillary concentration method known as large-volume sample stacking and high-efficiency CE separation has been developed to analyze and detect colorants in several food samples, such as soft drinks, jellies and milk beverages. Following optimization, this technique significantly reduced the limits of detection of eight food colorants commonly used in food products by up to two orders of magnitude when compared with the conventional capillary electrophoresis method. The developed technique was able to successfully determine colorants in food samples that had concentrations as low as 0.1-0.5 microg/ml.

The colorant properties of pigments from Opuntia stricta, Opuntia undulata, and Opuntia ficus-indicafruits were studied. The pigments were extracted with different solvents and identified by high-performance liquid chromatography. On the basis of their visible light spectra, the pigments were identified as betalains. In O. undulata and O. ficus-indica fruits, both betacyanins and betaxantins were identified, while in O. stricta fruits only betacyanins (betanin and isobetanin) were detected. O. stricta fruits showed the highest betacyanin content (80 mg/100 g fresh fruit). The thermal stability of the pigment extracts was dependent on the pH, with the maximum stability being at pH 5, as expected for betacyanins. At this value and a storage temperature of 4 degrees C, a deactivation half-life time of more than 1 year, with no added stabilizers, was determined. According to these studies, cactus pears from O. stricta may well be considered as a potential source of natural red colorants.

Five synthetic and five natural colorants were determined in lyophilized dairy products and fatty foods using an automatic method based on lixiviation and a solid-phase extraction process that includes cotton and RP-C(18) columns for the sequential retention of synthetic colorants and natural colorants, respectively. The lyophilization of the sample coupled with the separation procedure provides clean extracts despite the complexity of the matrices studied. In addition, the lyophilization process preserves the sample for at least 2 months without changes in the concentrations of the colorants. Identification and determination of synthetic and natural colorants were carried out using a liquid chromatograph equipped with a diode array detector. The detection limits achieved for all of the colorants (0.03-75 microg/g of lyophilized sample) allowed their determination within the limits established by the European Union, with good precision (approximately 4.5%). In addition, colorants spiked to different foods provided average recoveries (spiked at three concentration levels in four types of dairy samples and in three types of fatty foods) near 94 +/- 4%.