Search

Copyright of Atomic Energy Science & Technology is the property of Editorial Board of Atomic Energy Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

An energy harvester that employs both electromagnetic and piezoelectric effects to convert fluid flow energy in the pipeline into electrical energy for powering wireless sensor nodes (WSNs) of the pipeline condition monitoring system has been developed. The devised hybrid energy harvester comprised a unimorph circular piezoelectric plate fixed in a T-joint, three stacked magnets attached at the middle of the piezoelectric plate, and an adjustable coil holder holding a wound coil. Experimental results of the developed prototype depict that it can produce a maximum load RMS voltage of 3.36 V with the piezoelectric part at 27 kΩ of optimal load resistance and 286 mV from the electromagnetic part at 335 Ω of optimum load resistance. Moreover, at 2.9 kPa flow pressure amplitude and 11.08 l/s flow rate, a maximum load power of 418 µW from the piezoelectric portion and 244 µW with the electromagnetic portion is produced. Upon integrating the harvester with a rectifier circuit, an open circuit DC voltage of 9.4 and 3.32 V are generated with piezoelectric and electromagnetic parts, respectively. Furthermore, under the same fluid flow condition, the piezoelectric part produces 404 µW DC power at 92 kΩ of optimum load resistance, while the electromagnetic portion produces 163 µW DC power at 10 kΩ of optimum load resistance. The developed harvester is also utilized to recharge a 4.8 V power bank from 1.11 to 4.2 V in 210 min. Moreover, it is also integrated with a pipeline condition monitoring system to power a WSN, a controller, and relevant circuitry. [ABSTRACT FROM AUTHOR]

Mechanical vibrations can be effectively converted into electrical energy using a liquid type of energy harvesting device comprised of a ferrofluid and a permanent magnet-inductor coil assembly. Compared to solid vibration energy harvesting devices, the liquid nature of the ferrofluid overcomes space conformity limitations which allow for the utilization of a wider range of previously inaccessible mechanical vibration energy sources for electricity generation and sensing. This report describes the design and the governing equations for the proposed liquid vibration energy harvesting device and demonstrates vibration energy harvesting at frequencies of up to 33 Hz while generating up to 1.1 mV. The proposed design can continuously convert mechanical into electrical energy for direct discharge or accumulation and storage of electrical energy. [ABSTRACT FROM AUTHOR]

Copyright of Shipin Kexue/ Food Science is the property of Food Science Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Electric Machines & Control / Dianji Yu Kongzhi Xuebao is the property of Electric Machines & Control and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The International Thermonuclear Experiment Reactor (ITER) Thermal shield (TS) serves as a cryogenic heat exchanger to maintain the thermal stability of the ITER superconducting magnet coil, which is critical to the control of the plasma during the operation of the ITER device. The TS is composed of long-length 316L stainless steel (SS) and copper as brazed joints. In this case, a feasible fabrication design for the CCS TS is presented, accomplished by three kinds of joining processes (vacuum brazing, friction stir weld, and TIG weld). In the reliable fabrication design, the brazing quality of the as-brazed long-distance 316L SS and copper joints plays a critical role in the thermal conductivity performance of the ITER thermal shield. Therefore, a high-quality vacuum brazing process of long-length SS/Cu joints applied in a low-temperature superconductor magnet system was first studied. The macro metallography analysis demonstrates the braze ratio of the samples is 100%, and no crack or defect is observed in the samples. The microstructural characterization reveals the brazing seams are composed of silver-based Ag-rich eutectic. The micro-shear test indicates that the shear strength of the 316L tube and copper joint is 205 MPa, with the fracture position located on the copper side; this zone will be the most vulnerable zone of the joints. In addition, the SEM results illustrated that the shear fracture morphology displayed a ductile fracture feature. The test results demonstrated that the highly precise depth drilling employed in this paper ensured a good control of the brazing clearance, resulting in a 100% braze ratio for the long-length SS/Cu joints. Therefore, it can be concluded that the brazing process can be applied in the ITER TS for the good thermal conductivity performance of long-length SS/Cu-brazing joints. [ABSTRACT FROM AUTHOR]

Copyright of Machine Tool & Hydraulics is the property of Guangzhou Mechanical Engineering Research Institute (GMERI) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Next generation EUV sources for photolithography use light produced by laser-produced plasmas (LPP) from ablated tin droplets. A major challenge for extending the lifetime of these devices is mitigating damage caused by deposition of tin debris on the sensitive collection mirror. Especially difficult to stop are high energy (up to 10 keV) highly charged tin ions created in the plasma. Existing solutions include the use of stopping gas, electric fields, and magnetic fields. One common configuration consists of a magnetic field perpendicular to the EUV emission direction, but such a system can result in ion populations that are trapped rather than removed. We investigate a previously unconsidered mitigation geometry consisting of a magnetic null by performing full-orbit integration of the ion trajectories in an EUV system with realistic dimensions and optimize the coil locations for the null configuration. The magnetic null prevents a fraction of ions from hitting the mirror comparable to that of the perpendicular field, but does not trap any ions due to the chaotic nature of ion trajectories that pass close to the null. This technology can potentially improve LPP-based EUV photolithography system efficiency and lifetime and may allow for a different, more efficient formulation of buffer gas. [ABSTRACT FROM AUTHOR]

We suggested an original method to investigate the Fermi surfaces (FSs) in the quasi-two-dimensional conductors some time ago [A.G. Lebed and N.N. Bagmet, Phys. Rev. B 55, R8654 (1997)]. It was based on a consideration of a perpendicular conductivity in quasi-two-dimensional metals in parallel magnetic fields in the framework of the Boltzmann kinetic equation, where it was shown that the conductivity was independent on impurities. In this paper, we demonstrate that the above mentioned result is much more general than the kinetic equation and can be obtained even in a fully quantum mechanical case. We suggest to investigate this possible phenomenon in the quasi-two-dimensional organic, high- , and some others superconductors in a metallic phase to judge if the Fermi liquid picture is valid for them or not. If the Fermi liquid picture is valid, then study of the perpendicular resistivity in the rotated parallel magnetic field allows to extract important information about the two-dimensional Fermi surfaces. [ABSTRACT FROM AUTHOR]

The geometric characteristics of a saccular aneurysm play a crucial role in its rupturing. This article thoroughly investigates the impact of the sac centerline on aneurysm rupture, with a focus on identifying significant factors related to rupture at different time intervals. The study employs comprehensive computational simulations of six models of the ICA with varying coiling porosities and blood HCTs, using CFD analysis to examine WSS, OSI, pressure, and velocity within the saccular aneurysm for different sac centerlines. The results indicate that higher blood HCT levels lead to increased WSS and pressure values on the aneurysm wall, while OSI and mean velocity decrease. The study also reveals that coiling techniques can significantly reduce the risk of rupture, as decreasing coil porosity (increasing coil permeability) increases OSI and pressure while decreasing WSS and blood velocity within the aneurysm sac. [ABSTRACT FROM AUTHOR]

The Helmholtz coil constant (kh) is a crucial standard in magnetic moment measurement devices for permanent magnet materials. To overcome the problem of lowaccuracy of the direct-current (DC) calibration method, this study used a constant sinusoidal current in the Helmholtz coil and measured the induced voltage of the detection coil with known coil turns and coil area. Subsequently, the kh was calculated. The noise signal deduction rate in the induction voltage of the detection coil was greater than 99%, its influence on the induction voltage is less than 0.005%, and the repeatability of the calibration results is 0.003% (1δ). The results reveal that the alternating current (AC) method and orthogonal calculation (OC) can accurately measure the valid values of the voltage signal under the influence of the spatial stray field during the calibration of kh. [ABSTRACT FROM AUTHOR]

A 70 MeV H− cyclotron system was commissioned in order to measure the beam characteristics for the isotope separation on line (ISOL) operation in the energies range between 40 and 70 MeV. Using internal beams, the cyclotron magnet was precisely isochronized by applying the Smith-Garren method, achieving a main-coil current margin of 0.2 A for the beam stability. In the center region, beam profiles were measured by a differential radial probe to verify the specified dee voltage of 50 kV, which allows well-defined turn separation. Extracted beams were then used to check the beam line alignment by monitoring beam losses on segmented collimators and measuring variations on beam profiles. We measured transverse emittances of the cyclotron beam at a current of 25 µA by observing the beam profiles with upstream quadrupole strengths varied, which was the first time for this kind of 70 MeV cyclotron. Transmission efficiency along the beam line was measured as above 98% at a current of 100 µA. A temporary beam line was installed in the ISOL area, and we measured beam current distributions using a beam profile monitor shaped by wobbling at 60 Hz at a target location for beam diameters of 2 and 5 cm. A specific current distribution is generally required to reduce the maximum thermal stresses induced on the target. Finally, a maximum beam power of 50 kW was successfully tested at 70 MeV for 6 h. [ABSTRACT FROM AUTHOR]

With sensitivity being the Achilles' heel of nuclear magnetic resonance (NMR), the superior mass sensitivity offered by micro-coils can be an excellent choice for tiny, mass limited samples such as eggs and small organisms. Recently, complementary metal oxide semiconductor (CMOS)-based micro-coil transceivers have been reported and demonstrate excellent mass sensitivity. However, the ability of broadband CMOS micro-coils to study heteronuclei has yet to be investigated, and here their potential is explored within the lens of environmental research. Eleven nuclei including 7Li, 19F, 31P and, 205Tl were studied and detection limits in the low to mid picomole range were found for an extended experiment. Further, two environmentally relevant samples (a sprouting broccoli seed and a D. magna egg) were successfully studied using the CMOS micro-coil system. 13C NMR was used to help resolve broad signals in the 1H spectrum of the 13C enriched broccoli seed, and steady state free precession was used to improve the signal-to-noise ratio by a factor of six. 19F NMR was used to track fluorinated contaminants in a single D. magna egg, showing potential for studying egg–pollutant interactions. Overall, CMOS micro-coil NMR demonstrates significant promise in environmental research, especially when the future potential to scale to multiple coil arrays (greatly improving throughput) is considered. [ABSTRACT FROM AUTHOR]

The extensive applications of double-suction centrifugal pumps consume a considerable amount of energy. It is urgent to reveal the detailed energy dissipation generation and find the critical factor for pump performance enhancement. In this investigation, the internal flow field of a double-suction centrifugal pump was obtained by solving the Reynolds averaged Navier–Stokes equations. The entropy production method was utilized to calculate and visualize irreversible energy dissipation. The Omega vortex method was utilized to identify vortical structures and determine the temporal and spatial relationship between entropy production and vortices. The results indicate that the entropy production in the main flow regions was critical in hydraulic loss, accounting for 54%–71% of the loss, and turbulent dissipation in the main flow regions of the impeller and volute casing dominated the variation of pump efficiency. The near-wall entropy production in the impeller positively correlated with the flow rate, but the impact was insignificant in volute casing. Although the suction chamber contributed minimally to the hydraulic loss, the backflows at the impeller inlet were relieved near the ribs, and the dissipation at the impeller inlet was reduced when the blade leading edges passed the ribs. By adopting Omega vortex identification, wake vortices, separation vortices, and their interactions were determined to correlate strongly with hydraulic loss in volute channels and near cutwaters. Furthermore, these vortices were influenced by the back flows from the impeller sidewall gaps. Additionally, this study can also provide the foundational principles for the optimal design of this type of pump. [ABSTRACT FROM AUTHOR]

The interaction of polyphenols with proteins depends on the structure and type of protein and polyphenols. This study aims to determine the interaction between different plant polyphenols and bovine serum albumin (BSA), as well as their influence on protein structure, proanthocyanidins (proanthocyanidins, PC), catechin (catechin, C), epigallocatechin gallate (Epigallocatechin gallate, EGCG), and tea polyphenols (TEA polyphenol, TP). The BSA was combined to form a polyphenolsBSA. The interaction of polyphenols with BSA and their effects on protein structure were analyzed by UV spectroscopy, fluorescence spectroscopy, infrared spectroscopy, and molecular docking. The results showed that the maximum absorption peak of BSA at 286 nm all shared an upward trend in a redshift with the increase of PC, C, EGCG and TP added. There was the UV maximum wavelength redshift EGCG (292 nm) >PC (288 nm), C (288 nm), TP (288 nm). The redshifted absorption peak was attributed to the EGCG as a monomer, more accessible to the hydrophobic amino acid residues of protein molecules. The fluorescence intensity of BSA decreased gradually, as the concentration of the four polyphenols increased. The polyphenols were interacted with BSA to make more tyrosine or tryptophan exposure, eventually resulting in the lower fluorescence intensity. There was the fluorescence spectroscopy maximum wavelength redshift EGCG>PC, C>TP (365 nm>364 nm, 364 nm>363 nm). Fluorescence spectrum indicated the static quenching of all four types of polyphenols to BSA. The rate constant of protein quenching of polyphenols was 1013 at temperatures of 290 and 300 K. The Ksv of EGCG-BSA decreased most outstandingly, when the temperature increased. The catechol structure in the EGCG molecule was broken or deformed at high temperature. The binding constant KA with temperature was the same as the quenching constant Ksv . The higher the temperature was, the smaller the binding constant KA was. All level 10³ demonstrated the weak interaction force between the four polyphenols and BSA. The binding site n was about 1, indicating the presence of a binding site. The fluorescence intensity of BSA gradually decreased with the concentration of the four polyphenols increased. Therefore, both polyphenols were interacted with BSA to make more tyrosine or tryptophan exposure, eventually resulting in lower fluorescence intensity. The infrared spectroscopy indicated that four polyphenols altered the secondary structure of BSA, and then promoted the protein structure stabilization. Amide I band absorption peak (1 657.44 cm−1) occurred the blue-shifted PC>TP>EGCG>C (1 656.15 cm−1>1 632.07 cm−1>1 631.49 cm−1 > 1 631.44 cm−1). Nicotinamide II band peak shape was widening. The hydrogen bond of the BSA increased after the interaction. After the addition of TP, PC, and C, the BSA secondary structure was changed from β-turn, random coil to β-sheet, ɑ-helix, and the relative content of β-sheet, ɑ-helix increases, indicating the enhanced compactness of BSA conformation. Specifically, β -sheet content increased in the order of C-BSA (40.20%)>PC-BSA (39.50%)>EGCG-BSA (39.32%)>TP-BSA (34.04%), indicated that the C was better promoted the secondary structure stability of BSA. Molecular docking results indicated that the binding site was located in the hydrophobic cavity of Sub-domain IIA. Intermolecular interaction forces were mainly hydrogen bonding, and hydrophobic forces, in the order of the Binding energy C (−3.72 kJ/ mol)

This article presents an experiment to measure the magnetic moment of a permanent magnet using a coil and a precision scale. The procedure consists of three steps: verifying the proportionality between the magnetic field and the current in the solenoid, measuring the magnetic force exerted by the coil on the magnet using the scale, and verifying the result by measuring the magnetic moment of the magnet using another method. The experiment demonstrates that the values obtained by both methods are very similar, validating the proposed procedure. Additionally, the relationships between the magnetic field and the electric current in a coil are explored, and it is concluded that the proportionality constant depends on the magnetic permeability of the medium, the density of turns, and the geometric parameters of the coil. [Extracted from the article]

Magnesium diboride (MgB 2) magnets have the potential to be the next-generation liquid-helium-free magnet for magnetic resonance imaging (MRI) application due to their relatively high superconducting transition temperature, high current density and low raw material cost compared with current commercial niobium-titanium (Nb-Ti) magnets. A typical superconducting magnet includes several coils. To produce an ultra-stable magnetic field for imaging in MRI, a superconducting electromagnet operating in a persistent mode is crucial. Superconducting coils of the electromagnet in MRI are short-circuited to operate in the persistent mode by connecting coils with superconducting joints. Persistent joints have been demonstrated for in-situ and ex-situ wires of both mono- and multi-filamentary structures, made predominantly by PIT techniques similar to those used in wire production. To realise further engagement of MgB 2 in MRI applications, enhancing the performance of MgB 2 superconducting joints is essential. This literature review summarises research and development on MgB 2 superconducting joining technology. [ABSTRACT FROM AUTHOR]

Copyright of Atomic Energy Science & Technology is the property of Editorial Board of Atomic Energy Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Driven by an eccentric mass through a two-layered cantilevered plectrum, the electromagnetic energy harvester (EEH) can convert low-frequency mechanical vibrations into continuous uni-directional rotation. To optimize the performance of the EEH, electromagnetic analysis of the EEH was conducted. Three-phase winding permanent magnet (PM) topology was employed, and combinations of different coils and magnet pole numbers were designed. Then, the finite element method (FEM) was applied to analyze the influence of the combinations of the coils and pole numbers as well as the PM dimensions on the three-phase induced voltage. Prototypes with different configurations were fabricated and the analysis effectiveness was confirmed. Furthermore, different types of stator yokes were designed to enhance the magnetic field. Compared to the original prototype, the output voltage of the optimal prototype increased by 0.5 V with the same rotation speed, and the harmonic components were sufficiently low. Then, experiments with excitation by linear reciprocating motions and swing motions were conducted. Under different exciting conditions, the optimal prototype can also induce the highest voltage amplitude. With an increase in the weight of the eccentric mass, a long duration can be reached that lasts up to 12 s. In summary, the proposed optimization can achieve a high-efficiency and high-power density EEH. [ABSTRACT FROM AUTHOR]

In the automobile sector, energy recovery and sustainability are becoming more and more important, and energy-harvesting suspension systems (EHSAs) have a lot of promise to improve vehicle efficiency. This investigation expands on prior work that investigated the viability of an EHSA that uses permanent magnets and amorphous core coils. The performance of the proposed system is demonstrated and enhanced in the current study through the development and optimization of a prototype. A thorough testing of the prototype is performed to determine design improvements for boosting the system's overall performance and to quantify the recovered energy. In previous work, a method was proposed to find the dependence of the magnetic flux with the relative position between the primary and secondary elements to obtain the optimal position for the system. This method is applied to optimize the energy harvesting coil by testing different configurations in terms of the placement and type of amorphous or nonamorphous core inside the energy harvesting coil. This is a crucial area of attention in order to maximize energy recovery while solving the low-frequency problem that suspension systems have (on the order of 10 Hz). [ABSTRACT FROM AUTHOR]

This work describes the characteristics of a device capable of detecting the magnetic field generated by a submerged electrical conductor. This low-cost apparatus is based on the open-source Arduino platform and offers the possibility of monitoring magnetic fields generated by undersea cables. Measuring magnetic fields generated by undersea cables facilitates the development of technologies that will harness marine energy potential. The research is based on published parameters of magnetic field values generated by existing submarine cables. A coil was built to simulate an approximate magnetic field at 10 mT. The magnetic field generated by the coil was used as a reference standard. The device developed has a measurement probe built with an array of SS49E Hall effect sensors placed in a straight line and separated 5 cm from each other. A DS18B20 temperature sensor was added to make the necessary corrections and cancel the influence of temperature during the measurements. A microSD card module was attached to store continuous magnetic field measurements. The device was adjusted under strict laboratory conditions. The functionality of the device developed was confirmed by two samplings in the sea. In these samples, the magnetic field generated by the coil was measured in the entire water column from a depth of 3 m to 150 m. Results indicate that the prototype can successfully perform the necessary functions to quantify the underwater magnetic field accurately with about 10 µT accuracy. [ABSTRACT FROM AUTHOR]

High-temperature superconductors have great potential for various engineering applications such as a flywheel energy storage system. The levitation force of bulk YBCO superconductors can be drastically increased by increasing the strength of the external field. Therefore, a 6T conduction-cooled superconducting magnet has been developed for levitation force measurement application. Firstly, to protect the magnet from mechanical damage, reliable stress analysis inside the coil is paramount before the magnet is built and tested. Therefore, a 1/4 two-dimensional (2D) axisymmetric model of the magnet was established, and the mechanical stress in the whole process of winding, cooling down and energizing of the magnet was calculated. Then, the charging, discharging, and preliminary levitation force performance tests were performed to validate the operating stability of the magnet. According to the simulation results, the peak stresses of all coil models are within the allowable value and the winding maintains excellent mechanical stability in the superconducting magnet. The test results show that the superconducting magnet can be charged to its desired current of 150 A without quenching and maintain stable operation during the charging and discharging process. What is more, the superconducting magnet can meet the requirements for the levitation force measurement of both low magnetic field and high magnetic field. [ABSTRACT FROM AUTHOR]

Iron cores are widely employed in high temperature superconducting (HTS) power devices to enhance the magnetic field and improve the power density. In spite of these benefits, the presence of iron cores leads to a substantial increase in AC loss within HTS coil windings. Therefore, it is necessary to estimate the AC loss of HTS coil windings coupled with iron cores to propose methods for loss reduction. An effective way to reduce AC loss is to apply flux diverters (FDs) near the HTS coil windings. In this work, the 3D $T$ - $A$ homogenization method is used to calculate AC losses of the 1DPC (double pancake coil)-, 2DPC-, 4DPC-, and 8DPC assemblies at different currents with four ferromagnetic combinations: with an iron core (IC), with an iron core and FDs (IC_FDs), with an air core (AirC), and with air core and FDs (AirC_FDs). To weaken the impact of the iron core, the enlarged distance between the iron core and coil assemblies is considered to investigate AC loss dependence on this distance. In addition, the influence of the positions of FDs on AC loss reduction is also analyzed. The simulation results demonstrate that FDs can reduce the AC loss in coil assemblies, even when the iron core is present, owing to the reduction of the perpendicular magnetic field component in the end discs. For the 4DPC and 8DPC assemblies with IC, increasing the distance while using FDs, or decreasing the vertical gap between the coil assemblies and FDs, are effective in reducing AC loss.

In this study, we conducted a systematic exploration of a micro-electromagnetic vibration energy harvester with a bi-magnet structure and microelectromechanical systems 3D coils. First, we establish a physical model of stiffness and damping characteristics based on the superposition principle for the bi-magnet structure which has also been verified experimentally. Then, we investigate the influence of magnet gap and air gap on the stiffness and the magnetic flux change rate, mainly focusing on the distance and the potential barrier between the two potential wells. Finally, we fabricate and assemble the bi-magnet VEH prototype and tested the output performance under 1 and 6g excitation, which correspond the intra-well vibration and inter-well vibration, respectively. The tested results show that under 1g excitation, the prototype can output 155.38 μW power with 32 Hz half-power bandwidth and 4939.06 μW·Hz integrated power, which are obviously higher than those for mono-magnet under same excitation. When the excitation raises to 6g, the output power is improved to 362.98 μW with the half power bandwidth and integrated power enhanced to 56 Hz and 9289.96 μW·Hz, respectively. The tested results also prove that the structure proposed in this study can significantly enhance the output performance compared with a mono-magnet structure and other published data. [ABSTRACT FROM AUTHOR]

The design of optimized radiofrequency (RF) coils is a fundamental task for maximizing the signal-to-noise ratio (SNR) in Magnetic Resonance Imaging (MRI) and Magnetic Resonance Spectroscopy (MRS) applications. An efficient coil should be designed by minimizing the coil noise with respect to the sample noise, since coil conductor resistance affects data quality by reducing the SNR, especially for coils tuned to a low frequency. Such conductor losses strongly depend on the frequency (due to the skin effect) and on the conductor cross-sectional shape (strip or wire). This paper reviews the different methods for estimating conductor losses in RF coils for MRI/MRS applications, comprising analytical formulations, theoretical/experimental hybrid approaches and full-wave simulations. Moreover, the different strategies for minimizing such losses, including the use of Litz wire, cooled and superconducting coils, are described. Finally, recent emerging technologies in RF coil design are briefly reviewed. [ABSTRACT FROM AUTHOR]

In this study, an optimized unilateral magnetic resonance sensor with a three-magnet array is presented for assessing the aging of composite insulators in power grids. The sensor's optimization involved enhancing the static magnetic field strength and the homogeneity of the RF field while maintaining a constant gradient in the direction of the vertical sensor surface and maximizing homogeneity in the horizontal direction. The center layer of the target area was positioned 4 mm from the coil's upper surface, resulting in a magnetic field strength of 139.74 mT at the center point of the area, with a gradient of 2.318 T/m and a corresponding hydrogen atomic nuclear magnetic resonance frequency of 5.95 MHz. The magnetic field uniformity over a 10 mm × 10 mm range on the plane was 0.75%. The sensor measured 120 mm × 130.5 mm × 76 mm and weighed 7.5 kg. Employing the optimized sensor, magnetic resonance assessment experiments were conducted on composite insulator samples utilizing the CPMG (Carr–Purcell–Meiboom–Gill) pulse sequence. The T2 distribution provided visualizations of the T2 decay in insulator samples with different degrees of aging. [ABSTRACT FROM AUTHOR]

In this paper, mechanical responses and electro-thermal characteristics of a rare earth barium copper oxide (REBCO) high-temperature superconducting (HTS) insulated pancake coil during the quenching process are investigated through finite element modeling (FEM). Firstly, a two-dimensional axisymmetric electro–magneto–thermal–mechanical FEM model with real dimensions is developed. Based on the FEM model, a systematic study on the effects of the time taken to trigger the system dump, background magnetic field, material properties of constituent layers, and coil size on quench behaviors of an HTS-insulated pancake coil is implemented. The variations in the temperature, current, and stress–strain in the REBCO pancake coil are studied. The results indicate that an increase in the time taken to trigger the system dump can increase the peak temperature of the hot spot but has no influence on the dissipation velocity. An apparent slope change of the radial strain rate is observed when the quench occurs regardless of the background field. During quench protection, the radial stress and strain reach their maximum values and then decrease as the temperature decreases. The axial background magnetic field has a significant influence on the radial stress. Measures to reduce peak stress and strain are also discussed, which indicates that increasing the thermal conductivity of the insulation layer, copper thickness, and inner coil radius can effectively reduce the radial stress and strain. [ABSTRACT FROM AUTHOR]

Double‐sided microfabrication process on an ultra‐thin silicon film has rarely been attempted due to the challenges in terms of the preparation and handling of a thin film in spite of its promising fabrication potentials. Such a process allows for doubling the thin film device density or providing dual functionalities for a thin film depending on whether the front and back sides of a thin film are processed identically or distinctively. Here, a novel double‐sided thin film processing strategy is introduced by realizing a dual coil patterned ultra‐thin silicon film that is working as an actuating or energy harvesting system. Experimentally, a dual coil patterned thin film enabled using the introduced approach shows remarkably enhanced device performance when compared with a single coil patterned counterpart. Furthermore, a multiphysics simulation model is developed and the resultant modeling data validate the experimentally measured performance enhancement. Finally, the structural durability of the thin film upon cyclic loading is tested and its diverse vibration modes are investigated. [ABSTRACT FROM AUTHOR]

The use of pressurized bladders for stress control of superconducting magnets was firstly proposed at Lawrence Berkeley National Laboratory in the early 2000s. Since then, the so-called 'bladders and keys' procedure has become one of the reference techniques for the assembly of high-field accelerator magnets and demonstrators. Exploiting the advantages of this method is today of critical importance for Nb3Sn-based accelerator magnets, whose production requires the preservation of tight stress targets in the superconducting coils to limit the effects of the strain sensitivity and brittleness of the conductor. The present manuscript reports on the results of an experimental campaign focused on the optimization of the 'bladders and keys' assembly process in the MQXFB quadrupoles. These 7.2 m long magnets shall be among the first Nb3Sn cryomagnets to be installed in a particle accelerator as a part of the High Luminosity upgrade of the LHC. One of the main practical implications of the bladders technique, especially important when applied to long magnets like MQXFB, is that to insert the loading keys, the opening of a certain clearance in the support structure is required. The procedure used so far for MQXF magnets involved an overstress in the coils during bladder inflation. The work presented here shows that such an overshoot can be eliminated thanks to additional bladders properly positioned in the structure. This optimized method was validated in a short model magnet and in a full-length mechanical model, becoming the new baseline for the series production at CERN Furthermore, the results are supported by numerical predictions using finite element models. [ABSTRACT FROM AUTHOR]

In this paper, we describe a simple method for performing multifrequency eddy current characterization of free-standing uniform-thickness metallic foils using a forked inductive coil arrangement. The method involves measuring the mutual inductance between two coils when a foil is present between the coils, and when it is not present; the ratio of these mutual inductances is compared with an analytical solution, and foil conductivity, thickness, and sheet resistance are simultaneously estimated using numerical inversion and least-squares fitting. This method was used to characterize 34 non-ferrous metallic samples with thicknesses between 50 and 640 μm and with conductivities between 0.8 × 107 and 5.8 × 107 S/m. The estimated thicknesses from eddy current characterization agreed well with those measured using confocal optical techniques; the two approaches agreed to within 1 μm for samples that were thinner than 200 μm, and to within 0.5% for samples that had a thickness of 200 μm or greater. The estimated conductivities from eddy current characterization were in close agreement with expected values, given knowledge of the materials used. A particular strength of this approach is that the instrumentation needed is broadly available in research and development laboratories and the associated fixturing is easy to manufacture and assemble. A calibration procedure is described that can be used to reduce errors from geometric uncertainties. This calibration requires a sample that has only a known conductivity or thickness; both do not need to be known. The method described herein is likely extensible to conductivities and thickness well outside the ranges measured as part of this work. [ABSTRACT FROM AUTHOR]

Magnetically coupled resonant wireless power transmission technology (WPT) based on high-temperature superconducting (HTS) coils has gained wide popularity due to its low impedance and high-quality factor Q value characteristics. This technology has greatly improved the energy transfer performance of wireless power transmission (WPT) systems. However, practical applications of conventional WPT, such as wireless charging of autonomous underwater vehicles at mooring points, often encounter spatial misalignment issues due to the complex ocean environment and ocean currents. Nonetheless, few studies have investigated the spatial misalignment of HTS WPT systems, particularly the angular misalignment. This paper presents a solution to address this problem by constructing magnetically coupled resonant wireless energy transmission systems based on HTS coils and copper coils. The study analyzes the relationship between the transmission efficiency of the WPT system and the received power of the load with respect to the spatial orientation of the coil. The performance of the superconducting coil and copper coil WPT systems is compared. The experimental results demonstrate that, under the same spatially misaligned conditions, the WPT system using HTS coils can significantly improve the transmission efficiency and load power compared to the conventional copper WPT system. Moreover, simultaneous adjustment of the lateral misalignment distance and different orientation deflection angles can improve the transmission efficiency and smooth load output power of the high-temperature superconducting WPT system. [ABSTRACT FROM AUTHOR]

This paper employed an electrical circuit simulator to investigate an electrodynamic suspension system (EDS) for passenger rail transport applications. Focusing on a null-flux suspension system utilizing figure-eight-shaped coils (8-shaped coils), the aim was to characterize the three primary electromagnetic forces generated in an EDS and to compare the findings with existing literatures. The dynamic circuit theory (DCT) approach was utilized to model the system as an electrical circuit with lumped parameters, and mutual inductance values between the superconducting (SC) coil and the upper and lower loops of the 8-shaped coil were calculated and inputted into the simulator. The results were compared with experimental data obtained from the Yamanashi test track. The comparison demonstrated close alignment between the theoretical expectations and the obtained experimental curves, validating the accuracy of the proposed model. The study highlights the advantages of this new approach, including faster computation times and efficient implementation of modifications. Overall, this work contributes to the ongoing development and optimization of null-flux suspension Maglev systems. [ABSTRACT FROM AUTHOR]

The science of DNA nanotechnology has led to the synthesis of size-controllable materials with uniformed geometries at nano- and micro-scales. Herein, we proposed the double-crossover (DX), antiparallel, and even half-turns perimeter tiles (DAE tiles) to synthesize intact, mono-crystalline, and giant 2D DNA micro-assemblies. The DNA tiles with 10-half-turns perimeter were synthesized via self-assembly of 106 nucleotides (NT) circular scaffold along with the complimentary staple strands. The DAE DNA tiles were successfully polymerized to achieve stable lattices by adjusting the inter-tile distances of certain lengths for attaining torsional (or twisting) chirality. We determined that the inter-tile connections affected the degree of coiling (or super-coiling) and twisting forces (right- or left-handed twists) in the DNA helix. While the degree of polymerization of DNA tiles was also tune-able by controlling the lengths and structural designs of the circular core of the DNA tiles. Furthermore, the number of half-turns in the core and on the connection arms (4 or 5) with even "E" or odd "O" half-turns was crucial. It affected the direction of winding of DNA duplexes to alter the overall stiffness and sturdiness of DNA lattices. The number of half-turns in the connections were either "4 or Even (21 NT); E with 5 NT sticky ends" or "5 Odd (26 NT); O with 6 NT sticky ends" (DAE-E or DAE-O tile systems). The AFM results revealed that the above tile systems (DAE-E or DAE-O) together with the locations of crossovers, and holiday junctions along the DNA tiles controlled the left- or right-handed coiling of DNA double strands. This phenomenon affected the compactness of resulting DNA motifs, the overall intrinsic curvatures, double-strand packing, and the geometry of DNA lattices. [ABSTRACT FROM AUTHOR]

The object of research reported in this work is the fluctuations of the discharge current in Hall thrusters. The presence of significant fluctuations in the discharge current in Hall thrusters causes a significant deterioration of the thruster parameters – thrust, specific impulse, and efficiency. The task addressed in the current work relates to determining the main factors that affect the conditions for the occurrence of discharge current fluctuations, finding ways to reduce them, and obtaining optimal values of the parameters of the Hall thruster. The review of literary sources revealed that the specified problem is typical and has not yet been solved. In order to solve this problem, studies of the ST-40M Hall thruster were carried out in order to determine the main factors that have the greatest influence on the occurrence of oscillations and means of reducing the oscillations of the discharge current. The result of the research determined that the fluctuations of the discharge current depend most significantly on the parameters of the magnetic field in the acceleration channel of the thruster. The parameters of the magnetic field are determined by the magnitude of the currents of the thruster electromagnet coils, and the nature of oscillations, amplitude, and frequency may differ significantly with a slight change in the coil currents. As a result of the study, it was found that for the values of the currents of the coils of the magnetic system of the thruster, for which the level of fluctuations of the discharge current is minimal, the average value of the discharge current of the thruster also takes a minimum value. The research made it possible to determine the optimal operating modes of the Hall thruster, which ensure, at a given level of specific power, the maximum values of thrust, specific impulse, and thruster efficiency. The conclusions from the study could be useful for most developers of electric propulsion systems based on Hall thrusters [ABSTRACT FROM AUTHOR]

The magnetic spectrometer AMS-100, which includes a superconducting coil, is designed to measure cosmic rays and detect cosmic antimatter in space. This extreme environment requires a suitable sensing solution to monitor critical changes in the structure such as the beginning of a quench in the superconducting coil. Rayleigh-scattering-based distributed optical fibre sensors (DOFS) fulfil the high requirements for these extreme conditions but require precise calibration of the temperature and strain coefficients of the optical fibre. Therefore, the fibre-dependent strain and temperature coefficients K T and K ϵ for the temperature range from 77 K to 353 K were investigated in this study. The fibre was integrated into an aluminium tensile test sample with well-calibrated strain gauges to determine the fibre's K ϵ independently of its Young's modulus. Simulations were used to validate that the strain caused by changes in temperature or mechanical conditions was the same in the optical fibre as in the aluminium test sample. The results indicated a linear temperature dependence of K ϵ and a non-linear temperature dependence of K T . With the parameters presented in this work, it was possible to accurately determine the strain or temperature of an aluminium structure over the entire temperature range from 77 K to 353 K using the DOFS. [ABSTRACT FROM AUTHOR]

This paper presents a study on long-distance wireless power transfer (WPT), which formulates the voltage gain in terms of the coupling coefficient between the power transmitting unit (PTU) and the power receiving unit (PRU) coils. It is proposed that maximum power transfer efficiency (PTE) can be reached when maximum voltage gain is achieved under a matching condition between the coil quality factor and the coupling coefficient. In order to achieve maximum power delivered to load (PDL), we need to elevate the input voltage as high as the high breakdown-voltage of gallium nitride (GaN) high-electron mobility transistors (HEMT) along with class E amplifier circuit topology. In order to promote voltage gain, knowledge of the coupling coefficient between two coils including the factors of the coil diameter, wire diameter, coil turns, and the coil resistance are derived. It was observed that a lower coil resistance leads to a reduced parallel quality, which facilitates long-distance wireless power transfer. Experimental results support the findings that the maximum PTE occurred at the maximum voltage gain existing at a specific distance matches the coupling coefficient between coils. A maximum power point tracking (MPPT) method is also developed to achieve maximum PDL. At a distance of 35 cm, experiments with more than 100 W successfully receive a PTE of 57% at the PRU when the received voltage reached 1.4 kV. This is used to verify the concepts and analysis that are proposed in this paper. [ABSTRACT FROM AUTHOR]

The influences of slot/pole number combinations on electromagnetic performances, including flux linkage, inductance, and torque ripple harmonic components etc., resulting from unbalanced characteristics between north and south poles in concentrated winding permanent magnet (PM) machines with symmetrical and asymmetric rotor pole shaping methods are theoretically analysed and experimentally validated in this paper. It shows that for the PM machines with odd number of coils per phase per submachine, including consequent pole (CP) and surface‐mounted PM (SPM) machines, the influences of unbalanced pole characteristics can lead to additional torque ripple harmonics due to additive effects in windings, but can be cancelled in other machines. Compared with symmetrical pole shaping method, asymmetric pole shaping method can result in lower torque ripple for CPPM machines with odd number of coils per phase per submachine, while symmetrical and asymmetric pole shapes have similar effects on torque ripple reduction for other CPPM machines and all the SPM machines. The findings have been validated by finite element analyses on 12‐slot/8‐pole, 12‐slot/10‐pole, 9‐slot/6‐pole, and 12‐slot/14‐pole machines, and by experiments with 12‐slot/8‐pole and 12‐slot/10‐pole CPPM prototypes. [ABSTRACT FROM AUTHOR]

In line with global environmental regulations, the demand for eco-friendly and highly efficient aircraft propulsion systems is increasing. The combination of axial flux motors and superconductors could be a key technology used to address these needs. In this paper, an axial flux high temperature superconducting (HTS) motor for aircraft propulsion was designed and its characteristics were analyzed. A 2G HTS wire with high magnetic flux characteristic was used for the field winding of the 120 kW axial flux HTS motor, and the rotational speed and rated voltage of the motor were 2000 rpm and 220 V, respectively. The axial flux HTS motor implements a revolving armature type for solid cooling of the HTS field coil. The electromagnetic and thermal features of the motor were analyzed and designed utilizing a 3D finite element method program. The HTS coil was maintained at the target temperature by effectively designing the current lead and cooling system to minimize heat loss. These results can be effectively used in the design of propulsion systems for large commercial aircraft in the future as well as for the design of small aircraft with less than 4 seats. [ABSTRACT FROM AUTHOR]

Wiegand wires are unique ferromagnetic materials that display rapid magnetization reversal and a large Barkhausen jump under an applied field. This stable reversal can be used to induce a periodic pulse voltage in a pickup coil wrapped around the Wiegand wire. To unlock the full potential of Wiegand wires for magnetic sensors and devices, the magnetic structure and magnetization state of the Wiegand wire must be fully elucidated. In this study, hysteresis loops were used to reveal the magnetic structure of Wiegand wires. Wiegand wires of different diameters magnetized under different applied magnetic field strengths were analyzed in detail. Our results show that Wiegand wires 0.06 mm in diameter are composed solely of a hard magnetic core. Wiegand wires above 0.10 mm in diameter have a hard magnetic core, a middle layer, and a soft layer that decreases in thickness but increases in coercivity as the wire diameter decreases. Then, theoretical models were built to predict the magnetic structure of Wiegand wires under an applied field for the first time. The magnetization process of Wiegand wires with different diameters under different applied magnetic fields was also analyzed. [ABSTRACT FROM AUTHOR]

We report the development of an ultralow-noise bipolar current source based on the configuration of H-bridge current switching. The measured relative current noise fluctuation reaches 4 × 10−9 Hz−1/2, which enables an ultra-stable magnetic system for cold atom experiments. We avoid the influence of the AC leakage currents induced by the large parasitic capacitance of the H-bridge. First, the current sensor is placed as close as possible to the magnetic coils so that the systematic errors from these leakage currents are minimized. Second, the large parasitic capacitance, which parallels the magnetic coils and forms an LC oscillator, is removed from the feedback loop in our setup to maintain a large self-resonance frequency of the feedback control loop. These two improvements lead to a current source that is more precise and less noisy. Remarkably, the lowest current noise density produced by the proposed method is only 500 nA Hz−1/2 at a current of 100 A, which is about ten fold smaller than the case with leakage current. To optimize the feedback control, a numerical simulation is implemented by using Matlab Simulink, and the numerical simulation results are entirely consistent with the experimental results. [ABSTRACT FROM AUTHOR]

This article focuses on pioneering work on the performance of the three-dimensional (3D) magnetic field map in the entire volume of the Compact Muon Solenoid (CMS) detector at the Large Hadron Collider at CERN. In the CMS heterogeneous magnetic system, the magnetic flux is created by a superconducting solenoid coil enclosed in a steel flux-return yoke. To describe the CMS magnetic flux distribution, a system of the primitive 3D volumes containing the values of the magnetic flux density measured inside the superconducting coil inner volume and modelled outside the coil across a special mesh of reference nodes was developed. This system, called the CMS magnetic field map, follows the geometric features of the yoke and allows the interpolation of the magnetic flux density between the nodes to obtain the magnetic field values at any spatial point inside a cylinder of 18 m in diameter and 48 m in length, where all the CMS sub-detectors are located. The geometry of the volumes is described inside one 30° azimuthal sector of the CMS magnet. To obtain the values of the magnetic flux density components across the entire azimuth angle of the CMS detector, rotational symmetry is applied. [ABSTRACT FROM AUTHOR]