Search

Advanced ready-to-eat foods, which can be consumed directly or only need simple processed before consumption, refer to the products that processing with cutting-edge food science and technology and have better quality attribute. Cold chain and chemical addition are commonly used options to ensure microbial safety of high moisture advanced ready-to-eat foods. However, this requires freezing/thawing processing at high cost or has undesirable residue. Dehydration treatment has the potential to compensate those shortcomings. This article reviewed the positive effects of dehydration on advanced ready-to-eat foods, current application status of dehydration technologies, novel dehydration related technologies and the pathogenic bacteria control of products. It is observed that dehydration treatment is receiving increasing attention for ready-to-eat foods including space foods, 3 D-printed personalized foods and formula foods for special medical purposes. Recently developed drying technologies such as pulsed spouted microwave freeze-drying and infrared freeze-drying have attracted much interest due to their excellent drying characteristics. Finally, intelligent drying, dehydration-nano-hybridization and dehydration-induced multi-dimensional modification technology are some of the emerging R and D areas in this field. [ABSTRACT FROM AUTHOR]

A microfluidic chip is adopted to study the droplet dynamic behaviors when flowing through the T-junction. Large ranges of initial length (Lo/w = 0.8–2.8), capillary number (Cao = 0.030–0.165), and viscosity ratio (λo = 0.16–5.90) are considered to identify the deformation characteristics and the breakup results. Three flow patterns are categorized in the T-junction, and critical conditions are expressed as power law relations between the normalized length and the capillary number. The coupling competition exists between outer neck thinning and inner droplet shifting, which influences the deformation process. A state diagram indicating the number of breakups is built through two key features of the shifting behavior, namely, the shifting distance and the shifting velocity. With increasing viscosity ratio, thresholds of both breakups decrease due to the reduced deformation resistance caused by vortex flow and the weakened coupling effect, resulting from the suppressed shifting behavior. The shell thickness via twice-breakup pattern depends solely on the viscosity ratio. [ABSTRACT FROM AUTHOR]

The transport and deposition of particulate materials through fractures is widely involved in environmental engineering and resource development engineering. A 3D Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) coupling method was used to investigate the particle and fluid flow. The Gauss Model was applied to construct the rough surfaces. First, the numerical results were compared with the previous results and reasonable agreements were obtained. Second, the results indicated a novel flow pattern of particles in rough fractures. Then, a comprehensive particle sedimentary analysis indicated that the deposition distance of particles was inversely proportional to the particle size and density ratio. In addition, the particle deposition rates were increased by the mean roughness and there was an uneven sediment distribution impacted by roughness. Reasons for this uneven sediment distribution were analyzed in detail. Moreover, the bridge plugs of particles considering the closure of fractures were simulated as well. A part of particulate materials would be filtered at the inlet due to size effect and the transport distance of entered particles decreased significantly when the particle was large. A critical particle radius (R

Chloride-induced corrosion of steel in reinforced concrete structures is one of the major causes of their deterioration over time. The analysis and research on the diffusion mechanism of chloride ions in reinforced concrete structures is still insufficient, and it is necessary to calculate the path of chloride ions based on theoretical models. In this paper, the fick’s second law was used to describe the free chloride concentration evolution in concrete. The Monte Carlo simulation was used to predict the cumulative distribution of corrosion initiation of reinforcing steel.The results show that the calculated results of the established model are in good agreement with the measured results.

The Coulomb interaction effect in disordered conductors has long been a topic of fundamental importance and intense attention. Here, we systematically study the influence of this effect on the electrical transport of a series of ∼ 1 μ m thick Sn-doped indium oxide (ITO) films grown at different oxygen partial pressures. We find that both the electrical conductivity σ and Hall coefficient R H vary linearly with T from ∼ 35 K down to ∼ 4 K. The extracted electron screening factor F ~ σ of each film is nearly in agreement with the corresponding theoretical value. Moreover, the F ~ σ values increase with decreasing carrier concentration in the ITO films, which originates from less screening effect of electrons and enhanced Coulomb interaction. These features are consistent with conventional three-dimensional Coulomb interaction theories. We explore the long-standing puzzle of the carrier concentration dependence of F ~ σ. Our results provide the fundamental physics to modulate the intensity of the Coulomb interaction effect, which may be useful to optimize the performance of electron transport for nanoscale electronic devices. [ABSTRACT FROM AUTHOR]

The application of flexible indium tin oxide (ITO-free) electrochromic devices has steadily attracted widespread attention in wearable devices. Recently, silver nanowire/poly(dimethylsiloxane) (AgNW/PDMS)-based stretchable conductive films have raised great interest as ITO-free substrate for flexible electrochromic devices. However, it is still difficult to achieve high transparency with low resistance due to the weak binding force between AgNW and PDMS with low surface energy because of the possibility of detaching and sliding occurring at the interface. Herein, we propose a method to pattern the pre-cured PDMS (PT-PDMS) by stainless steel film as a template through constructed micron grooves and embedded structure, to prepare a stretchable AgNW/PT-PDMS electrode with high transparency and high conductivity. The stretchable AgNW/PT-PDMS electrode can be stretched (5000 cycles), twisted, and surface friction (3M tape for 500 cycles) without significant loss of conductivity (ΔR/R ≈ 16% and 27%). In addition, with the increase of stretch (stretching to 10–80%), the AgNW/PT-PDMS electrode transmittance increased, and the conductivity increased at first and then decreased. It is possible that the AgNWs in the micron grooves are spread during PDMS stretching, resulting in a larger spreading area and higher transmittance of the AgNWs film; at the same time, the nanowires between the grooves come into contact, thus increasing conductivity. An electrochromic electrode constructed with the stretchable AgNW/PT-PDMS exhibited excellent electrochromic behavior (transmittance contrast from ~61% to ~57%) even after 10,000 bending cycles or 500 stretching cycles, indicating high stability and mechanical robustness. Notably, this method of preparing transparent stretch electrodes based on patterned PDMS provides a promising solution for developing electronic devices with unique structures and high performance. [ABSTRACT FROM AUTHOR]