Search

The clinical report describes a three-dimensional (3D) printed coping for intraoral evaluation before milling final anterior restorations. The use of printed copings allows restorations for complex and esthetically important restorations to be thoroughly tested at relatively low cost without introducing large delays into the fabrication process.

Objectives: The purpose of this study was to investigate the simulated cuspal deflection and flexural properties of high viscosity bulk-fill and conventional resin composites., Methods: Seven high viscosity bulk-fill resin composites and eight conventional resin composites were used. Aluminum blocks (10 mm x 8 mm x 15 mm) with a mesio-occlusal-distal (MOD) cavity [4 (W) mm x 8 (L) mm x 4 (D) mm] were prepared and randomly divided into groups for different measurement techniques [micrometer vs CSLM] and further subdivided according to type of resin composite (high viscosity bulk-fill vs conventional resin composite). The simulated cuspal deflection resulting from the polymerization of resin composite bonded to a precisely machined MOD cavity within an aluminum block was measured with either a novel highly accurate submicron digimatic micrometer (MDH-25 M, Mitsutoyo, Tokyo, Japan) or a confocal laser scanning microscope (CLSM, VK-9710, Keyence, Tokyo, Japan) cuspal measurement method. In addition, flexural properties of tested resin composites were measured to investigate the relationship between simulated cuspal deflection and flexural properties. Scanning electron microscopy observation of tested resin composites was also conducted., Results: The simulated cuspal deflection of high viscosity bulk-fill resin composites was similar to that of conventional resin composites, regardless of measurement method. There were no statistically significant differences (p > 0.05) between the micrometer and CLSM cuspal measurement methods. There were statistically significant differences (p < 0.05) in flexural strength and elastic modulus depending on the material, regardless of the type of resin composite. Pearson correlation analysis did not show any statistically significant (p < 0.05) relationship between flexural properties and cuspal deflection., Conclusions: The results of this study indicate that high viscosity bulk-fill resin composites show similar cuspal deflection with bulk-filling techniques, to those shown by conventional resin composites with incremental filling techniques. Simulated cuspal deflection can be measured using either a micrometer or CLSM, but this experiment failed to show any relationship between the flexural properties and simulated cuspal deflection of resin composites., Significance: High viscosity bulk-fill resin composites produce the same level of cuspal deflection as a conventional incrementally filled resin composite., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

The relationship between enamel bond fatigue durability and surface free-energy characteristics with universal adhesives was investigated. The initial shear bond strengths and shear fatigue strengths of five universal adhesives to enamel were determined with and without phosphoric acid pre-etching. The surface free-energy characteristics of adhesive-treated enamel with and without pre-etching were also determined. The initial shear bond strength and shear fatigue strength of universal adhesive to pre-etched enamel were higher than those to ground enamel. The initial shear bond strength and shear fatigue strength of universal adhesive to pre-etched enamel were material dependent, unlike those to ground enamel. The surface free-energy of the solid (γ S ) and the hydrogen-bonding force (γSh) of universal adhesive-treated enamel were different depending on the adhesive, regardless of the presence or absence of pre-etching. The bond fatigue durability of universal adhesives was higher to pre-etched enamel than to ground enamel. In addition, the bond fatigue durability to pre-etched enamel was material dependent, unlike that to ground enamel. The surface free-energy characteristics of universal adhesive-treated enamel were influenced by the adhesive type, regardless of the presence or absence of pre-etching. The surface free-energy characteristics of universal adhesive-treated enamel were related to the results of the bond fatigue durability., (© 2018 Eur J Oral Sci.)

Objectives: The purpose of this study was to examine the enamel bond durability of universal adhesives in the self-etch mode under 2-year water storage and thermal cycling conditions., Materials and Methods: Three commercially available universal adhesives and a gold standard two-step self-etch adhesive were used. Ten specimens of bovine enamel were prepared per test group, and shear bond strength (SBS) was measured to determine the bonding durability after thermal cycling (TC) or long-term water storage (WS). The bonded specimens were divided into three groups: (1) specimens subjected to TC, where the bonded specimens were stored in 37 °C distilled water for 24 h before being subjected to 3000, 10,000, 20,000 or 30,000 TC; (2) specimens stored in 37 °C distilled water for 3 months, 6 months, 1 year or 2 year; and (3) specimens stored in 37 °C distilled water for 24 h, serving as a baseline., Results: The two-step self-etch adhesive showed significantly higher SBS than the universal adhesives tested, regardless of the type of degradation method. All universal adhesives showed no significant enamel SBS reductions in TC and WS, when compared to baseline and the other degradation conditions., Conclusions: Compared to the bond strengths obtained with the two-step self-etch adhesive, significantly lower bond strengths were obtained with universal adhesives. However, the enamel bond durability of universal adhesives was relatively stable under both degradation conditions tested., Clinical Relevance: The present data indicate that the enamel bond durability of universal adhesives in the self-etch mode might be sufficient for clinical use.

Purpose: To investigate the influence of application time and etching mode of universal adhesives on enamel adhesion., Materials and Methods: Five universal adhesives, Adhese Universal, Bondmer Lightless, Clearfil Universal Bond Quick, G-Premio Bond, and Scotchbond Universal, were used. Bovine incisors were prepared and divided into four groups of ten teeth each. SBS, Ra, and SFE were determined after the following procedures: 1. self-etch mode with immediate air blowing after application (IA); 2. self-etch mode with prolonged application time (PA); 3. etch-and-rinse mode with IA; 4. etch-and-rinse mode with PA. After 24-h water storage, the bonded assemblies were subjected to shear bond strength (SBS) tests. For surface roughness (Ra) and surface free energy (SFE) measurements, the adhesives were simply applied to the enamel and rinsed with acetone and water before the measurements were carried out., Results: Significantly higher SBS and Ra values were obtained with etch-and-rinse mode than with self-etch mode regardless of the application time or type of adhesive. Although most adhesives showed decreased SFE values with increased application time in self-etch mode, SFE values in etch-and-rinse mode were dependent on the adhesive type and application time., Conclusions: Etching mode, application time, and type of adhesive significantly influenced the SBS, Ra, and SFE values.

Objectives: The aim of this study was to determine the effect of double-layer application of universal adhesives on the bond quality and compare to other adhesive systems., Methods: Two universal adhesives used were in this study: Scotchbond Universal (SU), [3M ESPE] and Prime & Bond elect (PE), [Dentsply Caulk]. The conventional single-step self-etch adhesives G-ӕnial Bond (GB), [GC Corporation.] and BeautiBond (BB), [Shofu Inc.], and a two-step self-etch adhesive, Optibond XTR (OX), [Kerr Corporation], were used as comparison adhesives. Shear bond strengths (SBS) and shear fatigue strengths (SFS) to human enamel and dentin were measured in single application mode and double application mode. For each test condition, 15 specimens were prepared for SBS testing and 30 specimens for SFS testing., Results: Enamel and dentin SBS of the universal adhesives in the double application mode were significantly higher than those of the single application mode. In addition, the universal adhesives in the double application mode had significantly higher dentin SFS values than those of the single application mode. The two-step self-etch adhesive OX tended to have lower bond strengths in the double application mode, regardless of the test method or adherent substrate., Conclusion: The double application mode is effective in enhancing SBS and SFS of universal adhesives, but not conventional two-step self-etch adhesives., Significance: These results suggest that, although the double application mode may enhance the bonding quality of a universal adhesive, it may be counter-productive for two-step self-etch adhesives in clinical use., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Purpose: To comparatively evaluate universal adhesives and two-step self-etch adhesives for enamel bond fatigue durability in self-etch mode., Methods: Three universal adhesives (Clearfil Universal Bond; G-Premio Bond; Scotchbond Universal Adhesive) and three two-step self-etch adhesives (Clearfil SE Bond; Clearfil SE Bond 2; OptiBond XTR) were used. The initial shear bond strength and shear fatigue strength of the adhesive to enamel in self-etch mode were determined., Results: The initial shear bond strengths of the universal adhesives to enamel in self-etch mode was significantly lower than those of two-step self-etch adhesives and initial shear bond strengths were not influenced by type of adhesive in each adhesive category. The shear fatigue strengths of universal adhesives to enamel in self-etch mode were significantly lower than that of Clearfil SE Bond and Clearfil SE Bond 2, but similar to that OptiBond XTR. Unlike two-step self-etch adhesives, the initial shear bond strength and shear fatigue strength of universal adhesives to enamel in self-etch mode was not influenced by the type of adhesive., Clinical Significance: This laboratory study showed that the enamel bond fatigue durability of universal adhesives was lower than Clearfil SE Bond and Clearfil SE Bond 2, similar to Optibond XTR, and was not influenced by type of adhesive, unlike two-step self-etch adhesives., Competing Interests: The authors of this manuscript certified that they had no proprietary, financial, or other personal interest of any nature or kind in any product, service, and/or company that is presented in this article.

The aim of the present study was to determine the influence of different adhesive application methods and etching modes on enamel bond effectiveness of universal adhesives using shear bond strength (SBS) testing and surface free-energy (SFE) measurements. The adhesives Scotchbond Universal, All-Bond Universal, Adhese Universal, and G-Premio Bond were used. Prepared bovine enamel specimens were divided into four groups, based on type of adhesive, and subjected to the following surface treatments: (i) total-etch mode with active application; (ii) total-etch mode with inactive application; (iii) self-etch mode with active application; and (iv) self-etch mode with inactive application. Bonded specimens were subjected to SBS testing. The SFE of the enamel surfaces with adhesive was measured after rinsing with acetone and water. The SBS values in total-etch mode were significantly higher than those in self-etch mode. In total-etch mode, significantly lower SBS values were observed with active application compared with inactive application; in contrast, in self-etch mode there were no significant differences in SBS between active and inactive applications. A reduction in total SFE was observed for active application compared with inactive application. The interaction between etching mode and application method was statistically significant, and the application method significantly affected enamel bond strength in total-etch mode., (© 2017 Eur J Oral Sci.)

Purpose: To evaluate the effects of oxygen inhibition of universal adhesive on dentin bond durability and interfacial characteristics., Methods: The three universal adhesives used were Scotchbond Universal Adhesive, Prime & Bond Elect, and G-Premio Bond. Shear bond strength (SBS) and shear fatigue strength (SFS) of resin composite bonded to adhesive with and without an oxygen inhibited layer (OIL) on dentin using total-etch and self-etch modes were determined. Surface free energy (SFE) and SFE parameters of cured adhesive with and without an OIL on dentin using total-etch and self-etch modes were also measured by the sessile drop method., Results: The presence of an OIL in universal adhesives promoted higher SBS and SFS regardless of etching mode. In addition, regardless of adhesive type and etching modes, the specimens with an OIL showed a higher ratio of SFS/SBS than those without an OIL. Further, the SFEs, especially total SFE, polarity force and hydrogen bonding force, of cured adhesives with an OIL were significantly higher than those without an OIL., Clinical Significance: The present findings indicated that the oxygen inhibition of universal adhesive did not impair the dentin bond durability and interfacial characteristics of the adhesive., Competing Interests: The authors declared no conflict of interest.

Purpose: To examine the effect of reduced phosphoric acid pre-etching times on enamel fatigue bond strength of universal adhesives and surface characteristics by using atomic force microscopy (AFM)., Materials and Methods: Three universal adhesives were used in this study (Clearfil Universal Bond [C], G-Premio Bond [GP], Scotchbond Universal Adhesive [SU]). Four pre-etching groups were employed: enamel pre-etched with phosphoric acid and immediately rinsed with an air-water spray, and enamel pre-etched with phosphoric acid for 5, 10, or 15 s. Ground enamel was used as the control group. For the initial bond strength test, 15 specimens per etching group for each adhesive were used. For the shear fatigue test, 20 specimens per etching group for each adhesive were loaded using a sine wave at a frequency of 20 Hz for 50,000 cycles or until failure occurred. Initial shear bond strengths and fatigue shear strengths of composite adhesively bonded to ground and pre-etched enamel were determined. AFM observations of ground and pre-etched enamel were also conducted, and surface roughness as well as surface area were evaluated., Results: The initial shear bond strengths and fatigue shear strengths of the universal adhesives in the pre-etched groups were significantly higher than those of the control group, and were not influenced by the pre-etching time. Significantly higher surface roughness and surface area of enamel surfaces in pre-etched groups were observed compared with those in the control group. While the surface area was not significantly influenced by etching time, surface roughness of the enamel surfaces in the pre-etched groups significantly increased with pre-etching time., Conclusions: The results of this in vitro study suggest that reduced phosphoric acid pre-etching times do not impair the fatigue bond strength of universal adhesives. Although fatigue bond strength and surface area were not influenced by phosphoric-acid etching times, surface roughness increased with increasing etching time.

Objectives: The purpose of this study was to determine the influence of different frequency rates on of bond durability of self-etch adhesives to enamel using shear fatigue strength (SFS) testing., Methods: A two-step self-etch adhesive (OX, OptiBond XTR), and two single step self-etch adhesives (GB, G-ӕnial Bond and SU, Scotchbond Universal) were used in this study. The shear fatigue strength (SFS) to enamel was obtained. A staircase method was used to determine the SFS values with 50,000 cycles or until failure occurred. Fatigue testing was performed at frequencies of 5Hz, 10Hz, and 20Hz. For each test condition, 30 specimens were prepared for the SFS testing., Results: Regardless of the bond strength test method, OX showed significantly higher SFS values than the two single-step self-etch adhesives. For each of the three individual self-etch adhesives, there was no significant difference in SFS depending on the frequency rate, although 20Hz results tended to be higher., Conclusions: Regardless of the self-etch adhesive system, frequencies of 5Hz, 10Hz, and 20Hz produced similar results in fatigue strength of resin composite bonded to enamel using 50,000 cycles or until bond failure., Significance: Accelerated fatigue testing provides valuable information regarding the long term durability of resin composite to enamel bonding using self-etch adhesive system., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Objectives: The purpose of this study was to determine the dentin bonding ability of three new universal adhesive systems under different etching modes using fatigue testing., Method: Prime & Bond elect [PE] (DENTSPLY Caulk), Scotchbond Universal [SU] (3M ESPE), and All Bond Universal [AU] (Bisco) were used in this study. A conventional single-step self-etch adhesive, Clearfil Bond SE ONE [CS] (Kuraray Noritake Dental) was also included as a control. Shear bond strengths (SBS) and shear fatigue strength (SFS) to human dentin were obtained in the total-etch mode and self-etch modes. For each test condition, 15 specimens were prepared for the SBS and 30 specimens for SFS. SEM was used to examine representative de-bonded specimens, treated dentin surfaces and the resin/dentin interface for each test condition., Results: Among the universal adhesives, PE in total-etch mode showed significantly higher SBS and SFS values than in self-etch mode. SU and AU did not show any significant difference in SBS and SFS between the total-etch mode and self-etch mode. However, the single-step self-etch adhesive CS showed significantly lower SBS and SFS values in the etch-and-rinse mode when compared to the self-etch mode. Examining the ratio of SFS/SBS, for PE and AU, the etch-and-rinse mode groups showed higher ratios than the self-etch mode groups., Significance: The influence of different etching modes on dentin bond quality of universal adhesives was dependent on the adhesive material. However, for the universal adhesives, using the total-etch mode did not have a negative impact on dentin bond quality., (Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.)

Purpose: To examine the influence of the oxygen inhibited layer (OIL) on shear bond strength (SBS) to dentin and surface free energy (SFE) characteristics of different adhesive systems., Materials and Methods: Three adhesive systems were used: Scotchbond Multipurpose (SM), Clearfil SE Bond (CS), and Scotchbond Universal (SU). Resin composite was bonded to dentin surfaces to determine SBS with and without OIL of adhesives. The SFE, dispersion force (γSd), polarity force (γSp), and hydrogen bonding force (γSh) of cured adhesives with and without an OIL were measured. Two-way ANOVA and Tukey's honestly significant difference (HSD) test were used for analysis of SBS data, and one-way ANOVA and Tukey's HSD test were used for the SFE and contact angle data., Results: The SBS of SM and CS showed no significant differences between specimens with and without the OIL. However, the SBS of SU with the OIL was significantly higher than without the OIL. The SFE, γSp, and γSh of cured adhesives with an OIL were significantly higher than those of cured adhesives without an OIL. The SFE, γSp, and γSh of SM and CS with an OIL were significantly higher than those of SU with an OIL., Conclusion: The results of this study indicate that the presence of an OIL with a single-step self-etching adhesive promotes higher SBS to dentin, unlike in the other types of adhesive systems. The SFE characteristics of the OIL of dental adhesives differed depending on the type of adhesive system.

Purpose: To use shear bond strength (SBS) and shear fatigue strength (SFS) testing to determine the influence of phosphoric acid pre-etching times prior to application of self-etch adhesives on enamel bonding., Materials and Methods: Two single-step self-etch universal adhesives (Prime&Bond Elect and Scotchbond Universal), a conventional single-step self-etch adhesive (G-ӕnial Bond), and a conventional two-step self-etch adhesive (OptiBond XTR) were used. The SBS and SFS were obtained with phosphoric acid pre-etching for 3, 10, or 15 s prior to application of the adhesives, and without pre-etching (0 s) as a control. A staircase method was used to determine the SFS with 10 Hz frequency for 50,000 cycles or until failure occurred. The mean demineralization depth for each treated enamel surface was also measured using a profilometer., Results: For all the adhesives, the groups with pre-etching showed significantly higher SBS and SFS than groups without pre-etching. However, there was no significant difference in SBS and SFS among groups with > 3 s of preetching. In addition, although the groups with pre-etching showed significantly deeper demineralization depths than groups without pre-etching, there was no significant difference in depth among groups with > 3 s of pre-etching., Conclusion: Three seconds of phosphoric acid pre-etching prior to application of self-etch adhesive can enhance enamel bonding effectiveness.

Objectives: The surface free energy and dentine bond strength of self-adhesive cements were examined after the removal of temporary cements., Methods: The labial dentine surfaces of bovine mandibular incisors were wet ground with #600-grit SiC paper. Acrylic resin blocks were luted to the prepared dentine surfaces using HY Bond Temporary Cement Hard (HY), IP Temp Cement (IP), Fuji TEMP (FT) or Freegenol Temporary Cement (TC), and stored for 1 week. After removal of the temporary cements with an ultrasonic tip, the contact angle values of five specimens per test group were determined for the three test liquids, and the surface-energy parameters of the dentine surfaces were calculated. The dentine bond strengths of the self-adhesive cements were measured after removal of the temporary cements in a shear mode at a crosshead speed of 1.0mm/min. The data were subjected to one-way analysis of variance (ANOVA) followed by Tukey's HSD test., Results: For all surfaces, the value of the estimated surface tension component γ(S)(d) (dispersion) was relatively constant at 41.7-43.3 mJm(-2). After removal of the temporary cements, the value of the γ(S)(h) (hydrogen-bonding) component decreased, particularly with FT and TC. The dentine bond strength of the self-adhesive cements was significantly higher for those without temporary cement contamination (8.2-10.6 MPa) than for those with temporary cement contamination (4.3-7.1 MPa)., Conclusions: The γ(S) values decreased due to the decrease of γ(S)(h) values for the temporary cement-contaminated dentine. Contamination with temporary cements led to lower dentine bond strength., Clinical Significance: The presence of temporary cement interferes with the bonding performance of self-adhesive cements to dentine. Care should be taken in the methods of removal of temporary cement when using self-adhesive cements., (Copyright © 2011 Elsevier Ltd. All rights reserved.)