Search

The application of a strong electric field within a dielectric medium can produce a jet-like motion of ionized liquid from a high-voltage electrode to a grounded heated plate. Ionic jet impingement on the upper surface of a horizontal plate where boiling is occurring significantly modifies the boiling curve. Heat transfer enhancement has been observed both at saturation temperature and in subcooled conditions, up to a regime of fully-developed nucleate boiling. In addition, the ionic jet is capable of preventing the formation of a vapor film on the boiling surface up to much higher heat fluxes. The working fluids are FC-72 and HFE-7100. Two different high-voltage electrodes have been tested: a single pin and an array of 7 points. This novel electrohydrodynamic technique of ionic-jet impingement boiling can greatly increase, with negligible or very low power input, both the heat transfer coefficients on a heated plate and the critical heat flux for the transition to the film boiling regime (up to 160%). [ABSTRACT FROM AUTHOR]

The thermofluid-dynamic effects of ion injection from sharp metallic points added perpendicularly to the inner wire of a short horizontal annulus were experimentally investigated. A dielectric liquid (FC-72 by 3M) was weakly forced to flow in the duct, which was uniformly heated on the outer wall. A dc voltage as high as 22 kV was applied to the inner electrode, while the heated wall was grounded. Both the laminar and the turbulent mixed-convection regimes were obtained, varying the imposed flow rate. Once an electric field is applied, the flow is dramatically modified by the jets of charged particles, which transfer their momentum to the neutral adjacent ones. Different injection strengths were obtained on the emitters, because the shape of the point tips was not controlled at the microscale. Nusselt number distributions were obtained azimuthally and longitudinally, monitoring the wall temperatures. In all cases, heat transfer turned out greatly enhanced in the proximity of the emitters, without a significant increase in pressure drop through the test section and with a negligible Joule heating, making this technique very attractive for application in compact heat exchangers. [ABSTRACT FROM AUTHOR]

Space cooling is currently the fastest-growing end-user in buildings. The global warming trend combined with increased population and economic development will lead to accelerated growth in space cooling in the future, especially in China. The hot summer and cold winter (HSCW) zone is the most densely populated and economically developed region in China, but with the worst indoor thermal environment. Relatively few studies have been conducted on the actual measurements in the optimization of insulation design under typical intermittent cooling modes in this region. This case study was conducted in Chengdu—the two residences selected were identical in design, but the south bedroom of the case study residence had interior insulation (inside insulation on all opaque interior surfaces of a space) retrofitted in the bedroom area in 2017. In August 2019, a comparative on-site measurement was done to investigate the effect of the retrofit work under three typical intermittent cooling patterns in the real-life scenario. The experimental result shows that interior insulation provides a significant improvement in energy-saving and the indoor thermal environment. The average energy savings in daily cooling energy consumption of the south bedroom is 42.09%, with the maximum reaching 48.91%. In the bedroom with interior insulation retrofit, the indoor temperature is closer to the set temperature and the vertical temperature difference is smaller during the cooling period; when the air conditioner is off, the room remains a comfortable temperature for a slightly longer time. [ABSTRACT FROM AUTHOR]

A modelling approach based on the Substitutive Coefficients Network (SCN) is developed to predict the thermal behavior of a system in the dynamic state-space, without requiring knowledge of the thermal mass. The method can apply either to large- (building, combined solar systems, geothermal energy, and thermodynamic installations) or to small-scale systems (heat exchangers, electronic devices cooling systems, and Li-ion batteries). This current method is based on a dimensionless formulation of the simplified dynamic thermal balance model, using relaxation time as a key parameter to establish the model. The introduction of relaxation time reduces the parameters set as guidance coefficients. The parameters are finally expressed by a combination of global heat transfer coefficients related to each layer and/or sub-layer of the system. Advantages of the method are reliability, "non-destructibility", i.e., it allows a reliable prediction of the thermal behavior which experimentally is inaccessible, and reducibility of the parameters size estimate. Additionally, the method is inexpensive in terms of computation memory. It is also easy to implement in practical numerical schemes. In this paper, the method leads to a simplified mathematical model that predicts the thermal behavior of a mono-zone eco-cottage building installed at Lorraine University (in Longwy, France) as a case study. Thermal performance of the building is estimated under the hourly weather conditions onsite, as obtained from the Meteonorm software. The thermal dynamics within hourly Typical Meteorological Year 2 (TMY2) Meteonorm data disturbances and the internal heating input state in the winter period were simulated with a simplified numerical discretization method. Results provide a general dynamic state of the different sub-components of the system, with limited design of the model parameters. [ABSTRACT FROM AUTHOR]

• The TES allows a cost and primary energy consumption up to 8% and 13% respectively. • The energy flexibility depends on the TES capacity and the operation control. • The DR specific cost is reduced between 45% and 75% with TES installed. • Performance maps can be created to characterise building flexibility potential. The present paper assesses the capability of a cost-optimal control strategy to activate demand response actions in a building equipped with an air-source heat pump coupled with a water thermal storage system. Commencing with a reference scenario where no demand response actions are considered, the electricity consumption pattern and the operational cost are evaluated. Several demand response scenarios are next considered by adapting consumption patterns by reduction of baseline heat pump power consumption. The difference between the operational cost evaluated under a specific demand response program and the benchmark cost are used to assess the marginal cost that should be considered to provide incentives to promote user participation in demand response programs. The results illustrate the effectiveness of thermal energy storage for reducing the total system operational cost and its seasonal primary energy consumption, both with and without demand response actions. The application of the proposed methodology over the whole heating season, allows performance maps to be created that can be used either by the grid-operator or end-user to identify the best demand response action to be implemented on any particular day. These maps represent useful decision tools to assess and optimise the flexibility potential while meeting end-user needs. [ABSTRACT FROM AUTHOR]

This paper analyzes the use of hybrid photovoltaic/thermal (PVT) collectors in nearly zero-energy buildings (NZEBs). We present a design methodology based on the dynamic simulation of the whole energy system, which includes the building energy demand, a reversible heat pump as generator, the thermal storage, the power exchange with the grid, and both thermal and electrical energy production by solar collectors. An exhaustive search of the best equipment sizing and design is performed to minimize both the total costs and the non-renewable primary energy consumption over the system lifetime. The results show that photovoltaic/thermal technology reduces the non-renewable primary energy consumption below the nearly zero-energy threshold value, assumed as 15 kWh/(m2·yr), also reducing the total costs with respect to a non-solar solution (up to 8%). As expected, several possible optimal designs exist, with an opposite trend between energy savings and total costs. In all these optimal configurations, we figure out that photovoltaic/thermal technology favors the production of electrical energy with respect to the thermal one, which mainly occurs during the summer to meet the domestic hot water requirements and lower the temperature of the collectors. Finally, we show that, for a given solar area, photovoltaic/thermal technology leads to a higher reduction of the non-renewable primary energy and to a higher production of solar thermal energy with respect to a traditional separate production employing photovoltaic (PV) modules and solar thermal (ST) collectors. [ABSTRACT FROM AUTHOR]