Search

This is a case of unilateral masseter muscle hypertrophy (MMH) treated with botulinum toxin (NHAI - normalised hemi-facial asymmetry index improvement from 5.48 to 3.04). After 19 months, the treatment was repeated because of hypertrophy relapse (NHAI increase up to 6.82). The volume variations in the masseter area were monitored during 25 months using a laser scanner to compute facial volume. In order to relate the cause of hypertrophy and relapse to the presence of parafunctional activities, a nocturnal electromyography (EMG) study was conducted with positive results (nocturnal parafunctions of patients 4074.99 µV to be compared with a control group value of 1644.63 µV). The lack of the left inferior molars and the consequent right coclusal support seemed to justify the hypertrophy of right masseter (MMRight-POC [percent overlapping coefficient} 91.9%). However, the prosthetic rehabilitation did not prevent relapse in the same muscle. The EMG analysis of both the muscular activation (MMRight-POC 66.0% after relapse) and inhibition activity in Maximum Voluntary Clench (MVC) resulted in contradictory conclusions. At present, the available knowledge regarding MMH physiopathology is very limited and does not support a therapeutic rationale for relapse prevention. [ABSTRACT FROM AUTHOR]

Statement of Problem: New polyvinyl siloxane (PVS) materials with enhanced properties have been developed to improve and facilitate implant impression techniques. However, studies on their accuracy are lacking., Purpose: The purpose of this in vitro study was to determine the accuracy and precision of implant impressions made with some recently introduced materials on a simulated patient requiring an all-on-4 implant-supported prosthesis. Well-established polyether materials were also evaluated as a comparison. The variables considered were material type, consistency, splinting or not splinting techniques, and implant angulation., Material and Methods: A reference master model was made by inserting 4 implants at angles of 0, 5, and 10 degrees. Eighty impressions were made at 37 °C in wet conditions by using a standardized technique. Eight groups (n=10) were created using monophasic, single-viscosity materials (Hydrorise Implant Medium, HIM-ns; Hydrorise Implant Medium, HIM; Honigum Mono, HM; Impregum, IMP), and 2-viscosity materials (Hydrorise Implant Heavy+Light-ns, HIH+L-ns; Hydrorise Implant Heavy+Light, HIH+L; Honigum Heavy+Light, HH+L; and Permadyne and Garant [Heavy+Light, PeH+L]). Hydrorise materials were used with splinting and not splinting (ns) techniques. The reference points located on the connecting platforms of the transfer copings (TCP) were compared with the same points on the implant connecting platforms (ICP) located in the reference model. The accuracy and precision of the impressions were determined as linear 3D errors and standard deviation between each TCP-ICP couple by using an optical coordinate measuring machine (OCMM)., Results: PVS materials were generally better than polyether materials, with Hydrorise materials (HIM and HIH+L) showing significantly better accuracy and precision (30.9 ±14.4 μm and 28.7 ±15.5 μm, respectively) than IMP and PeH+L polyethers (44.2 ±16 μm and 43.8 ±17.6 μm, respectively; P<.001). Honigum materials were statistically similar to Hydrorise materials (P=.765). The values shown by Hydrorise nonsplinted groups (HIH+L-ns and HIM-ns) were not statistically different from those of the splinted polyether impressions (P=.386). The viscosities (monophasic or heavy+light) had no effect on accuracy, but monophasic material positively influenced precision (HIM and HIH+L, P=.001). No correlation was found between implant angulation and accuracy (multilevel analysis and Kendall rank correlation coefficient=-0.065; P=.133)., Conclusions: Recently introduced materials designed for implant impressions showed significantly higher accuracy and precision; even with the unfavorable nonsplinting technique, the new materials performed similarly to, or better than, polyether materials. Although the transfer coping splinting technique generally improved the accuracy and precision of Hydrorise materials, the effect was significant only within HIH+L groups., (Copyright © 2021 The Authors. Published by Elsevier Inc. All rights reserved.)

Background: Current methodologies in the prevision of post-surgical features of the face in orthognathic surgery are mainly 2-D. An improvement is certainly given by the introduction of CT, but its acceptance is controversial due to its high biological cost. As an alternative, in this study an effective procedure for the construction of a 3-D textured digital model of the face and dental arches of patients with dentofacial malformations using a 3-D laser scanner at no biological cost is presented., Methods: A 3-D Laser scanner Konica-Minolta VIVID 910 is used to obtain multiple scans from different perspectives of the face of patients with dentofacial malocclusions requiring orthognathic surgery. These multiple views are then recombined, integrating also the maxillary and mandibular arch plaster casts, to obtain the 3-D textured model of the face and occlusion with minimal error., Results: A viable methodology was identified for the face and occlusal modeling of orthognathic patients and validated in a test case, confirming its effectiveness: the 3-D model created accurately describes the actual features of the patient's face; the proposed methodology can be easily applied in the clinical routine to accurately record the steps of the surgical treatment and to perform accurate anthropometric analyses of the facial morphology, and thus constitute the necessary database for the development of previsional tools in orthognathic surgery., Conclusions: The proposed method is effective in recording all the morphological facial features of patients with dentofacial malformations, to develop a facial modification database and tools for virtual surgery.