Search

Objectives: To investigate prospectively the relation between vibration-induced white finger (VWF) and measures of cumulative (lifetime) exposure to hand-transmitted vibration (HTV). Methods: Two hundred and forty-nine HTV workers and 138 control men of the same companies participated in a 3-year follow-up study. The diagnosis of VWF (Raynaud’s phenomenon in the controls) was based on the medical history, the administration of colour charts and the results of a cold test. Tool vibration magnitudes were expressed as root-mean-square (r.m.s.) acceleration, frequency-weighted according to international standard ISO 5349-1 and also unweighted over the frequency range 6.3–1250 Hz. From the vibration magnitudes and exposure durations, alternative measures of cumulative vibration dose were calculated for each HTV worker, according to the expression: dose = Σ a i m t i , where a i is the acceleration magnitude on tool i , t i is the lifetime exposure duration (hours) for tool i , and m = 0, 1, 2 or 4. Results: The incidence of VWF varied from 5 to 6% in the HTV workers versus 0 to 1.5% for Raynaud’s phenomenon in the controls. After adjusting for potential confounders, measures of cumulative vibration dose derived from total operating hours and high powers of unweighted acceleration (ie, , with m >1) gave better predictions of the occurrence of VWF than dose measures calculated from frequency-weighted acceleration (ie, ). These findings were observed in the entire sample of HTV workers, in those with no VWF at the initial investigation, and in those with normal cold test results at baseline. Conclusions: This prospective cohort study suggests that measures of cumulative vibration doses constructed from unweighted r.m.s. acceleration perform better for the prediction of VWF than dose measures calculated according to the recommendations of current standards. These findings should contribute to the improvement of the ISO frequency weighting for evaluating the severity of hand-transmitted vibration.

The aim of this study was to investigate the relation between low back pain (LBP) outcomes and measures of daily exposure to whole-body vibration (WBV) in professional drivers. In a study population of 202 male drivers, who were not affected with LBP at the initial survey, LBP in terms of duration, intensity, and disability was investigated over a two-year follow-up period. Vibration measurements were made on representative samples of machines and vehicles. The following measures of daily WBV exposure were obtained: (i) 8-h energy-equivalent frequency-weighted acceleration (highest axis), A(8)(max) in ms(-2) r.m.s.; (ii) A(8)(sum) (root-sum-of-squares) in ms(-2) r.m.s.; (iii) Vibration Dose Value (highest axis), VDV(max) in ms(-1.75); (iv) VDV(sum) (root-sum-of-quads) in ms(-1.75). The cumulative incidence of LBP over the follow-up period was 38.6%. The incidence of high pain intensity and severe disability was 16.8 and 14.4%, respectively. After adjustment for several confounders, VDV(max) or VDV(sum) gave better predictions of LBP outcomes over time than A(8)(max) or A(8)(sum), respectively. Poor predictions were obtained with A(8)(max), which is the currently preferred measure of daily WBV exposure in European countries. In multivariate data analysis, physical work load was a significant predictor of LBP outcomes over the follow-up period. Perceived psychosocial work environment was not associated with LBP.

To investigate prospectively the relation between vibration-induced vascular disorders and measures of daily exposure to hand-transmitted vibration (HTV).Two hundred and forty-nine HTV workers and 138 control men of the same companies participated in a 3-year follow-up study. The diagnosis of vibration induced white finger (VWF) in the HTV workers and that of Raynaud's phenomenon in the controls was based on the medical history, the administration of color charts and the results of a cold test with measurement of finger systolic blood pressures. Vibration magnitudes from the tools were measured as r.m.s acceleration, frequency weighted according to international standard ISO 5349-1, and also unweighted over the frequency range 6.3-1,250 Hz. Daily vibration exposure was expressed in terms of daily exposure duration and frequency-weighted or unweighted r.m.s. acceleration normalized to a reference period of 8 h (Aw(8) or Auw(8), respectively).The incidence of VWF varied from 5 to 6% in the HTV workers versus 0-1.5% for Raynaud's phenomenon in the controls. After adjusting for potential confounders, Auw(8) gave better predictions of the incidence of VWF and the cold response of the digital arteries over time than Aw(8) or daily exposure duration. These findings were observed in the entire sample of HTV workers, in those with no VWF at the initial investigation, and in those with normal cold test results at baseline.The findings of this longitudinal study suggest that a measure of daily vibration exposure calculated from unweighted r.m.s. acceleration over the frequency range 6.3-1,250 Hz performs better for the prediction of vascular disorders in users of vibratory tools than a measure derived from r.m.s. acceleration frequency weighted according to ISO 5349-1. This study provides epidemiological evidence that more weight should be given to intermediate and high-frequency vibration for evaluating the severity of hand-transmitted vibration.

PM10 samples were collected during winter and summer seasons at two different sites in the area of Trieste (Italy). The content of As, Cd, Cr, Mn, Ni, Pb and V in the PM10 samples was determined by inductively coupled plasma-mass spectrometry, with the purpose of evaluating the relevance of PM10 inhalation as a route of human exposure to these elements. The results showed that the ambient air concentration of the aforementioned elements were below the limits or target values for both sites and season. Site and season-specific correlation analysis was conducted for the identification of metals with similar origin: very good correlation for the couple Ni-V was found in both sites and seasons, showing the influence of combustion of heavy oils in PM10 composition. The inter-site and seasonal variability of both PM10 and metal concentrations were examined. A stronger impact by the vehicular traffic on the PM10 and metal concentrations was found for the urban site in both seasons. Because of the great importance of the “Bora” wind on the local climate, variability of PM10 and toxic elements concentration with wind were analysed, allowing determination of the effect of wind on dilution of the pollutants for the urban site during both seasons.

Polyomavirus infection occurring during childhood is followed by a lifelong latency in immunocompetent subjects. The major site of polyomavirus persistence are the uroepithelial cells which leads to oral transmission. It has recently been hypothesized that tonsils could be a possible reservoir. The role of tonsil, adenoid, and peripheral blood mononuclear cells (PBMCs) as possible sites of JCV, BKV, and SV40 latency in young healthy children was assessed. Two hundred fifteen fresh specimens, including 57 tonsil, 80 adenoid, and 78 PBMC samples from 80 immunocompetent children (mean age 4.8 years) were analyzed to determine the viral load by quantitative real-time PCR. The human herpes virus 6 (HHV-6) was tested as a lymphotropic reference virus. Polyomavirus was detected in 5/80 (6.2%) children while HHV-6 infection affected 27/80 children (33.7%) (P < 0.001). SV40 was detected in one adenoid sample, while footprints of BKV were found in one adenoid and three tonsil samples. JCV was never found in all samples. Polyomavirus sequences were not detected in the 78 blood samples. One adenoid and two tonsils from three children (1.4%) were positive for both polyomavirus and HHV-6. Infections were characterized by low replication rates ranging typically from 1 x 10e(2)/5.5 x 10e(4) to 6.8 x 10e(3)/8.5 x 10e(4) viral copies/number of cells. In conclusion, tonsils and adenoids of children could effectively harbor BKV and SV40, although only very few cells proved to be infected. Nevertheless, the low prevalence of polyomavirus, in comparison with the lymphotropic HHV-6, suggests that these tissues are unlikely to be the preferred site of polyomavirus latency, at least in younger children.

Background Carpal tunnel syndrome (CTS) is a socially and economically relevant disease caused by compression or entrapment of the median nerve within the carpal tunnel. This population-based case-control study aims to investigate occupational/non-occupational risk factors for surgically treated CTS. Methods Cases (n = 220) aged 18-65 years were randomly drawn from 13 administrative databases of citizens who were surgically treated with carpal tunnel release during 2001. Controls (n = 356) were randomly sampled from National Health Service registry records and were frequency matched by age-gender-specific CTS hospitalization rates. Results At multivariate analysis, risk factors were blue-collar/housewife status, BMI ≥ 30 kg/m2, sibling history of CTS and coexistence of trigger finger. Being relatively tall (cut-offs based on tertiles: women ≥165 cm; men ≥175 cm) was associated with lower risk. Blue-collar work was a moderate/strong risk factor in both sexes. Raised risks were apparent for combinations of biomechanical risk factors that included frequent repetitivity and sustained force. Conclusion This study strongly underlines the relevance of biomechanical exposures in both non-industrial and industrial work as risk factors for surgically treated CTS.

Sulphur K-edge X-ray absorption near edge structure (XANES) spectroscopy was used to identify sulphur compounds in PM10 samples collected simultaneously at two sites with different environmental situations in the province of Trieste (NE of Italy), during summer and winter seasons respectively. The first site is an industrial site located near a steel mill plant and the second is a coastal site. The sulphur speciation at the industrial site has shown the presence of the following sulphur compounds in both seasons: organic compounds (thiophenes or Polycyclic Aromatic Sulphur Heterocycles — PAHs) and sulphates while in the winter season sulphites were also present. In the coastal site organic compounds (thiophenes or PASHs) and sulphate were found during winter season, moreover bisulphates were found during summer season. Relative percentages of the different sulphur compounds have shown that sulphate is the most abundant form of sulphur in the industrial site samples during both seasons and in the coastal site sample collected during the winter season (> 98%); in the coastal site sample collected during the summer season the relative percentages of bisulphate and sulphate were around 40% and 60% respectively.

There is a growing interest on nanoparticle safety for topical use. The benefits of nanoparticles have been shown in several scientific fields, but little is known about their potential to penetrate the skin. This study aims at evaluating in vitro skin penetration of silver nanoparticles. Experiments were performed using the Franz diffusion cell method with intact and damaged human skin. Physiological solution was used as receiving phase and 70 microg/cm2 of silver nanoparticles coated with polyvinylpirrolidone dispersed in synthetic sweat were applied as donor phase to the outer surface of the skin for 24h. The receptor fluid measurements were performed by electro thermal atomic absorption spectroscopy (ETAAS). Human skin penetration was also determined by using transmission electron microscope (TEM) to verify the location of silver nanoparticles in exposed membranes. Median silver concentrations of 0.46 ng cm(-2) (rangeLOD-2.23) and 2.32 ng cm(-2) (range 0.43-11.6) were found in the receiving solutions of cells where the nanoparticles solution was applied on intact skin (eight cells) and on damaged skin (eight cells), respectively. Twenty-four hours silver flux permeation in damaged skin was 0.62+/-0.2 ng cm(-2) with a lag time1h. Our experimental data showed that silver nanoparticles absorption through intact and damaged skin was very low but detectable, and that in case of damaged skin it was possible an increasing permeation of silver applied as nanoparticles. Moreover, silver nanoparticles could be detected in the stratum corneum and the outermost surface of the epidermis by electron microscopy. We demonstrated for the first time that silver applied as nanoparticles coated with polyvinylpirrolidone is able to permeate the damaged skin in an in vitro diffusion cell system.

Introduction Nanotechnologies are among the fastest growing areas of scientific research and have important applications in a wide variety of fields. The data suggest that in the future workers and consumers exposed to nanoparticles will significantly increase. Dermal absorption and toxicity of nanoparticles At now there are gaps in understanding about the human and environmental risk that manufactured nanoparticles pose for occupational exposed people and for consumers. There is a need for assessing the health and environmental impacts, the nanoparticles life cycle, the human exposure routes, the behavior of nanoparticles in the body, and the risk for workers. Possible routes of entry into the body include inhalation, absorption through the skin or digestive tract, injection, and absorption or implantation for drugs delivery systems. In particular, dermal absorption and skin penetration of nanoparticles needs a better evaluation because few and contradictory data are present in the literature, mainly on titanium dioxide. Conclusions There are limited data on carbon-based nanoparticles and very few data on other metal nanoparticles increasingly used in industry. The article reviews the literature on the percutaneous absorption of nanoparticles and their effect on skin.

The bioavailability of metals, which are known as important contact allergens, is decisive for the development and the maintenance of contact dermatitis. The aim of this study was to evaluate the percutaneous penetration of metal powders of cobalt (Co), nickel (Ni) and chromium (Cr) and the effect of skin lesions on skin absorption. In vitro permeation experiments were performed using the Franz diffusion cells with intact and damaged human skin. Physiological solution was used as receiving phase and metal powders (Co, Ni and Cr) dispersed in synthetic sweat at pH 4.5 were applied as donor phase to the outer surface of the skin for 24h. The amount of each metal permeating the skin was analysed by electro-thermal atomic absorption spectroscopy (ETAAS). Donor solution analysis demonstrated that metals were present as ions. Measurements of metals skin content were also exploited. Median Co and Ni concentrations found in the receiving phase were significantly higher when Co and Ni powders were applied on the abraded skin than after application on the intact skin (3566 and 2631ngcm(-2) vs. 8.4 and 31ngcm(-2), respectively). No significant difference was found in Cr permeation through intact and damaged skin. The measurement of metals skin content showed that Co, Ni and Cr concentrations were significantly higher in the damaged skin than in the intact skin. Co and Ni ions concentrations increased significantly when the donor solutions were applied on the damaged skin, while Cr ions concentrations did not increase. This study demonstrated that Co and Ni powders can permeate through damaged skin more easily than Cr powder, which has probably a stronger skin proteins binding capacity. Therefore, our results suggest that is necessary to prevent skin contamination when using toxic substances because a small injury to the skin barrier can significantly increase skin absorption.

An epidemiologic and clinical study of neck and upper limb musculoskeletal disorders was carried out on 65 vibration-exposed forestry operators using chain-saws and 31 comparable control subjects (maintenance workers) performing manual activity and not exposed to vibration. Upper limb function was evaluated by measuring finger and wrist circumference size, maximal hand grip strength and range of motion manoeuvres in both the controls and the exposed workers. Vibration from two chain-saws was measured, and vibration exposure for each forestry worker was assessed in terms of 4 h energy-equivalent frequency-weighted acceleration according to ISO 5349. Job analysis indicated a slight excess risk of upper extremity cumulative trauma disorders (CTDs) in the forestry operators compared with the control workers. After adjustment for age and body constitution, significantly higher prevalence rates of persistent upper limb pain, muscle-tendon syndromes and carpal tunnel syndrome were observed among the forestry workers than among the controls. In the forestry operators, the occurrence of upper limb musculoskeletal disorders increased with increasing vibration exposure. Upper limb function was found to be impaired in the forestry workers compared with the controls. Vibration exposure was significantly related to increased finger circumference size, diminished muscle force and reduced joint function. Even though it is difficult to establish the relative importance of vibration and ergonomic factors in the aetiology of CTDs, nevertheless the results of this study indicate that musculoskeletal impairment to the upper limbs was more severe in the forestry operators than in the controls who did solely manual work. This finding and the observed dose-effect relationships suggest that vibration stress is an important contributor to the development of musculoskeletal disorders in workers using hand-held vibrating tools.

In a group of 65 Italian forestry operators using chain saws, the overall prevalence of vibration-induced white finger (VWF) was found to be 29.2%. The occurrence of VWF was higher in the chain sawyers who had operated non-antivibration (non-A/V) as well as A/V saws (46.4%) than in those with experience limited to A/V saws (16.2%). The latency time before VWF averaged 9.4 yr (SD 6.8). The mean value of the four-hour energy-equivalent frequency-weighted acceleration [(ah,w)eq(4)] was 7.2 m/s2 (SD 1.2). On the basis of the known VWF prevalence and of [(ah,w)eq(4)], a latent period before VWF of 7.1 yr was expected according to ISO 5349. The measurement of finger systolic pressure (FSP) at 15°C and 10°C by plethysmographic technique showed that the chain sawyers affected with VWF experienced a more intense digital vasospasm than a group of comparable controls and the chain sawyers without VWF. The sensitivity of the method to detect vibration-induced digital arterial hyper-responsiveness to cold was 84.2% and the specificity was 100%. The findings of this study showed a good agreement between the expected and observed latency times before VWF, even though the ISO dose-effect relationship seems to overestimate slightly the risk. The results of the cold test indicated that the measurement of FSP during local cooling is an accurate laboratory method to diagnose objectively Raynaud's phenomenon of occupational origin.

Background Experimental and clinical evidence suggest that stress can lead to ill-health through the disregulation of the hypothalamic–pituitary–adrenal (HPA) axis. Studies to date have produced equivocal results likely due to different methodologies and failure to account for confounding factors. This investigation aimed to assess the relation between self-reported work-related stressors and salivary cortisol and to clarify the role of the potential confounders. Methods Thirty-six call-handlers completed a self-administered job content questionnaire and collected seven daily salivary samples on two workdays and a weekend. The diurnal salivary cortisol output was expressed as cortisol awakening response (CAR), and cortisol output in the rest of the day. Salivary cortisol data were normalized by means of square root transformation. The generalized estimating equations method was used to assess the relation between job strain and cortisol levels after adjusting for gender, weekdays and adherence to the sampling schedule. Results Job strain significantly influenced the total amount of cortisol response to waking (high strain vs. low strain: 1.1 (0.3–2.0) nmol/L). The cortisol response to waking showed gender-specific differences [women excreting greater cortisol than men: 1.1 (0.3–1.9) nmol/L], and weekday differences [workdays vs. weekend: 1.0 (0.3–1.6) nmol/L]. Noncompliance with the sampling protocol was associated with lower salivary cortisol than in adherent subjects. Conclusions Our results provide further evidence for the HPA axis involvement in the physiological response to work stress. The measure of the CAR showed to be the sensitive index to assess the physiological response to psychosocial factors. Gender, weekday, and protocol compliance were confounding factors. Am. J. Ind. Med. 52:251–260, 2009. 2008 Wiley-Liss, Inc.

To investigate the association between two job stress models—the job demand-control model and the effort-reward imbalance model—and repeated measures of salivary cortisol among male and female call-centre operators. Daily cortisol profiles consisting of seven time points were measured across two workdays and one leisure day to determine the cortisol awakening response and the cortisol output in the day in 104 volunteers. The employees completed two self-administered questionnaire—the Karasek’s demand-control questionnaire and the Siegrist’s effort-reward imbalance questionnaire—to assess psychosocial hazards at work. The relations between the perceived workload measures and salivary cortisol levels were analyzed by means of generalized estimating equations method after adjusting for potential confounders (gender, age, educational level, marital status, morning awakening time, sleep duration and quality, weekdays, work schedule, adherence to sampling procedure). The total cortisol amount excreted in the awakening period was positively associated with the job strain measures (high strain vs. low strain: 1.4 (2.4–0.3) nmol/l). In contrast, individuals scoring higher in effort-reward imbalance at work had both lower cortisol awakening response (high imbalance vs. low imbalance: −0.7 (−1.3 to −0.2) nmol/l) and lower diurnal secretory activity (−9.2 (−17.7 to −0.7) nmol/l). Gender, weekday and adherence to sampling schedule significantly influenced the cortisol excretion in the morning period. Our results indicate that the two work stress models differentially affect salivary cortisol output. This finding suggests that combining the information from two complementary job stress models results in improved knowledge on the psychobiological correlates of the psychosocial work environment.

The present study tried to investigate, using a synthetic sweat at pH 4.5, whether metallic chromium can pass through the skin (in vitro) and the effect of rapid skin decontamination with a common detergent. A suspension of chromium powder in synthetic sweat at pH 4.5 was prepared and shaken with a stirring plate at room temperature for 30 min. Human skin membranes were set up in Franz-diffusion cells and 1 ml of the freshly made suspension was applied to the outer surface of the skin for 24h. The tests were performed without and with decontamination using the cleanser 30 min after the start of exposure. The appearance of metal ions in the aqueous receptor phase was quantified by Electro Thermal Atomic Absorption Spectroscopy (ETAAS) and Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES). Speciation analysis and measurements of chromium skin content were also performed. Chromium skin permeation was demonstrated in in vitro experiments using the Franz cell system, giving a permeation flux of 0.84+/-0.25 ng cm(-2)h(-1) and a lag time of 1.1+/-0.7h. The cleaning procedure stop Cr permeation but its concentration into the skin significantly increased (Mann-Whitney U test P

The aim of this study was to measure the concentration of some metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Ti) in PM(10) samples collected in one urban and one industrial site and to assess that PM(10) total mass measurement may be not sufficient as air quality index due to its complex composition. Metals were determined by inductively coupled plasma-atomic emission spectroscopy (ICP-AES) and differential pulsed anodic stripping voltammetry (DPASV). The measured concentrations were used to calculate the content of metals in the PM(10) total mass, and to estimate the enrichment factors and the correlations between PM(10), metal concentrations and meteorological data for the two sites. The mean PM10 concentration during the sampling period in the urban site exceeded the annual European Union (EU) standard (40 microg/m(3)) and, for some sampling days, the daily EU standard (50 microg/m(3)) was also exceeded. In opposite, both EU standards were never exceeded in the industrial site. The overall metal content was nearly double in the industrial site compared to the urban one, and the mean Ni concentration exceeded the EU annual limit value (10 ng/m(3)). The metals with the highest enrichment factor were Cd, Cu, Ni and Pb for both sites, suggesting a dominant anthropogenic source for these metals. Metal concentrations were very low and typical of rural background during Christmas holidays, when factories were closed. PM(10) total mass measurement is not a sufficient air quality index since the metal content of PM(10) is not related to its total mass, especially in sites with industrial activities. This measurement should be associated with the analysis of toxic metals.

Objectives This study investigated the relation between salivary endothelin, vibration exposure, and vascular disorders in a group of forestry workers. Methods Altogether 54 forestry workers and 52 controls underwent a medical examination and a cold test with measurement of the percentage of change in finger systolic blood pressure after finger cooling from 30°C to 10°C (FSBP% 10° ). Salivary endothelin concentration (ET 1–21 , in fmol/ml) was measured by a commercially available enzyme-linked immunosorbent assay before and after the cold challenge. The anamnestic diagnosis of vibration-induced white finger (VWF), assisted by color charts, was based on the Stockholm Workshop criteria. Results Six forestry workers (11%) and one control (2%) reported white fingers. Before the cold challenge, the salivary ET 1–21 concentration was significantly greater in the VWF workers than in the controls (P=0.036). The cold response of digital arteries was stronger in the VWF workers than in the controls (P

The authors report the first results of a global survey on the working conditions in the forests of the Italian Alps, where the mechanization of the operations is limited, owing to the difficult geomorphological conditions. First, an organizational analysis was performed in all the phases of forest work by using the method of organizational congruences. The physiological cost of each task was evaluated by measuring oxygen consumption, lung ventilation during work, and the heart rate through 24-hour continuous dynamic electrocardiograph recording. The postural load on the lumbar disks for the main logging tasks was evaluated by means of a biomechanical analysis that estimated the compressive force applied to disk L3 in different positions. The vibrations transmitted to the worker's hand/arm system during the cutting activities were also measured. The results of the analysis suggest that potentially hazardous situations can be reduced by training operators in safer work practices and that the work organization must be improved since most tasks are physically too demanding, from both the metabolic and the cardiac point of view. The postures habitually assumed by workers during cutting exert a load on intervertebral disks that is much higher than if they assumed an ergonomically correct position. The health risk from vibrations requires a careful control of both the working conditions and the worker's state of health.

Two experiments were carried out to investigate the cardiovascular responses of vibration-exposed workers to autonomic stimulation. In the first experiment blood pressures, heart rate and systolic time intervals (STI) were measured during a cold test in 63 vibration-exposed foundry workers and 41 controls. STI, such as total electromechanical systole (QS2I) and left ventricular ejection time index (LVETI), were found to be shorter in the vibration-exposed workers with and without vibration white finger (VWF) than in the controls, both at rest and during cold provocation and recovery (p less than 0.001). A significant inverse relationship between urinary excretion of free catecholamines and the duration of STI was observed under resting conditions (0.001 less than p less than 0.03). In the second experiment, the above mentioned cardiovascular parameters were measured in 11 grinding operators with VWF and 11 controls during a hand grip test, an arithmetic test and an orthostatic test. Finger systolic pressures (FSP) during local cooling to 30, 15 and 10 degrees C were also measured. QS2I and LVETI were more abbreviated in the VWF subjects than in the controls at rest and during both the circulatory stress tests and the recovery periods (0.001 less than p less than 0.05). The reduction in FSP by local cooling from 30 degrees C to 15 and 10 degrees C was greater in the VWF workers than in the controls (p less than 0.001). Significant correlations were observed between the reduction in FSP at 15 and 10 degrees C and the duration of STI during circulatory stress activities (p less than 0.01). A multiple regression analysis pointed out that vibration exposure was the major determinant of STI during circulatory stress, while the importance of age and smoking and drinking habits in predicting STI was negligible. The findings of these studies suggest that the level of cardiac sympathetic activity is increased in VWF workers in comparison with controls. These experimental results are consistent with those of other investigators, indicating that excessive sympathetic reflex activity plays an important role in the pathogenesis of VWF.

To investigate the occurrence of vibration-induced white finger (VWF) and the cold response of digital arteries in a group of forestry workers, most of whom had used anti-vibration (AV) chain saws solely.One hundred and twenty-eight forestry workers underwent initially a medical examination and a standardized cold test with measurement of the change in finger systolic blood pressure after finger cooling from 30 to 10 degrees C (FSBP%(10 degrees )). They were re-examined two or three times over the calendar period 1990-1999. Seventy-one forestry workers were active over the entire follow up period, while 57 retired after 1-8 years from the initial investigation.The initial prevalence and the cumulative incidence of VWF over the follow up period were 26.6 and 11.7%, respectively. In the retired workers, the new cases of VWF occurred before their retirement, that is when they were still active. There were no significant changes in FSBP%(10 degrees ) in the active forestry workers over the follow up period. A significant increased in FSBP%(10 degrees ) (i.e. improvement) was observed in the retired workers at the end of the follow up. FSBP%(10 degrees ) at the cross-sectional investigation was significantly lower in the forestry workers who developed VWF during the follow up than in those who never experienced finger blanching over the study period.The findings of this follow up study suggest that forestry workers with work experience limited to AV chain saws are still at risk of developing VWF. Cessation of vibration exposure in the retired workers was associated with a beneficial effect on the cold response of digital arteries. Cold-induced digital arterial hyperresponsiveness at the initial investigation was a predictive factor for the onset of VWF over time.

There is a growing interest in the debate on nanoparticle safety for topical use. The benefits of nanoparticles have been shown in several scientific fields, but little is known about their potential to penetrate the skin lies. This study aims at evaluating in vitro silver nanoparticles skin penetration. Experiments were performed using the Franz diffusion cell method with intact and damaged human skin. Physiological solution was used as receiving phase and 70 microg/cm2 of silver nanoparticles dispersed in synthetic sweat were applied as donor phase to the outer surface of the skin for 24h. The receptor fluid measurements were performed by Electro Thermal Atomic Absorption Spectroscopy (ETAAS). Silver concentration of 0.2 microg/L was found in the receiving solutions of two cells, in which damaged skin membranes were set up. In the other tests, we obtained a silver concentration below the limit of detection in the receiving cells. Our experimental data show that silver nanoparticles permeation through intact and damaged skin is negligible. These findings are consistent with previously published results. Further researches are necessary to explore skin absorption of silver nanoparticles.

To investigate prospectively the relation between vibration-induced white finger (VWF), exposure to hand-trasmitted vibration (HTV) and the cold response of digital arteries in users of vibrating tools. Two-hundred and sixteen HTV workers and 133 control men of the same companies underwent initially a medical examination and a standardised cold test with measurement of the change in finger systolic blood pressure (FSBP) after finger cooling from 30 to 10°C. They were re-examined 1 year later. Tool vibration magnitudes were expressed as frequency-weighted and unweighted r.m.s. accelerations. From the vibration magnitudes and exposure durations, alternative measures of cumulative vibration dose were calculated for each HTV worker, according to the expression: $$ \text{dose} = \sum a_i^m t_i$$ , where a i is the acceleration magnitude on tool i, t i is the lifetime exposure duration for tool i, and m = 0, 1, 2 or 4. Among the HTV workers, the initial prevalence and the 1-year incidence of VWF were 18.1 and 1.7%, respectively. At the first examination, the HTV workers with moderate or severe score for VWF showed a significantly increased cold reaction in the fingers when compared with the controls and the HTV workers with no vascular symptoms. At the follow-up, the controls, the asymptomatic HTV workers, and the prevalent cases of VWF did not show significant changes in the cold response of digital arteries. A deterioration of cold-induced digital vasoconstriction was found in the incident cases of VWF. In the HTV workers, vibration doses with high powers of acceleration (i.e., $$ \text{dose} = \sum a_i^m t_i$$ with m > 1) were major predictors of the vasoconstrictor response to cold at the follow-up examination. The measurement of FSBP after local cooling may be a helpful objective test to monitor prospectively the change in vibration-induced vascular symptoms. The findings of this longitudinal study suggest a dose–effect relationship between cold-induced digital arterial hyperresponsiveness over time and measures of cumulative vibration exposure. In the controls, the cold response of the digital arteries was stable over 1-year follow-up period.

Health effects of occupational exposure to hand-transmitted vibration (HTV) and whole-body vibration (WBV) are reviewed. Excessive exposure to HTV from powered processes or tools is associated with an increased occurrence of symptoms and signs of disorders in the vascular, neurological and musculoskeletal systems of the upper limbs. This complex set of disorders is called hand-arm vibration syndrome. Long-term occupational exposure to intense WBV is associated with an increased risk for disorders of the lumbar spine and the connected nervous system. With a lower probability, the neck-shoulder, the gastrointestinal system, the female reproductive organs, the peripheral veins, and the cochleo-vestibular system are also assumed to be affected by WBV. However, there is weak epidemiological support for WBV-induced disorders of organ systems other than the lower back. In addition to the health effects of human vibration, this review provides information on methods for the protection and health surveillance of vibration-exposed workers according to the European Directive 2002/44/EC on mechanical vibration.

Many millions of workers are exposed to hand‐transmitted vibration from powered tools and are at risk of developing disorders in the fingers, hands, or arms.1,2,3,4 One consequence of prolonged regular exposure to hand‐transmitted vibration is impaired circulation in the fingers, often evident during or following exposure to cold. The symptoms may be first noticed as abnormally cold fingers, but disorder is often diagnosed from reports of attacks of blanching on the distal, middle, or proximal phalanges. The condition is named “vibration‐induced white finger” from the characteristic attacks of blanching that are assumed to be caused by vibration damage, although the attacks are most often provoked by cold.4 The mechanisms involved in this heightened sensitivity to cold are not known, and so there is uncertainty as to the range of symptoms and signs that characterise the disorder. Although it is clear that hand‐transmitted vibration causes vibration‐induced white finger, there is limited evidence as to the characteristics of vibration that are responsible for the injury. To obtain a number indicating the severity of an exposure to vibration (that is, evaluate the vibration), it is necessary to make assumptions as to the importance of the vibration magnitude, the vibration frequency, the vibration direction, the daily exposure duration, and life‐time exposure duration. Various standards have made such assumptions so as to define uniform methods for evaluating the vibration on powered tools. Having defined a measure of vibration severity, it is possible to assess the acceptability of the vibration, in terms of the probability or severity of disorder. In International Standard 5349‐1 (2001), the evaluation is performed using the root‐mean‐square value of the vibration acceleration after it has been frequency‐weighted (using a weighting called Wh), assuming all directions of vibration to be equally important and all locations of contact with the hand to be equally likely to lead to problems.5 The assessment of vibration severity uses the 8‐hour energy equivalent daily exposure (called A(8)) to predict the years of exposure before 10% of persons are likely to develop the first signs of finger blanching. The frequency weighting inherent in current standards and directives did not evolve from epidemiological studies of the conditions causing vibration‐induced white finger, or from experimental studies of the effects of different frequencies of vibration on relevant physiological responses.6,7 The frequency weighting was largely based on a study of how the discomfort produced by hand‐transmitted vibration depends on the frequency of vibration.8 Some recent epidemiological studies suggest that the frequency weighting may not be optimum and that, at least for the vibration on some groups of common tools, the onset of finger blanching may be predicted with greater accuracy without using frequency weighting Wh.9 The frequency weighting has a large effect on the relative importance of vibration on different tools and, consequently, on the risks of injury and the responsibilities of employers. Improved understanding of the importance of vibration frequency therefore has considerable importance. Contact with the vibration on a tool involves the application of force to the fingers. There are tasks that involve the application of a force without exposure to vibration which do not result in the characteristic symptoms of vibration‐induced white finger, so force alone cannot explain the disorder. However, force may be expected to have some direct mechanical effect on circulation within the fingers. Furthermore, force may alter the transmission of vibration into the fingers and hand: increased force will tend to stiffen the tissues, which will change resonance frequencies and tend to increase the transmission of vibration from the area of contact with vibration. Occupational exposures to hand‐transmitted vibration result in symptoms of vibration‐induced white finger after many months, usually years, of regular exposure to vibration. Laboratory studies have found reductions in blood flow during and following exposure of a finger to vibration. The effects are not restricted to the vibrated finger but are also observed in other fingers, including those on a hand not exposed to vibration. Previous experimental studies by the current authors have explored the effects of the magnitude, frequency, and duration of vibration on finger blood flow using controlled contact areas and controlled contact force.10,11,12 The effects of variations in contact force on finger blood flow have not previously been investigated. This study was designed to investigate whether the force applied by a finger affected finger blood flow and whether the effects of force interacted with the acute effects of vibration. Specifically, it was hypothesised that finger blood flow would be affected by the application of force and that the effects of vibration frequency would be dependent on the force applied to the finger.

The prevalence of low back pain (LBP) was investigated in 598 Italian professional drivers exposed to whole-body vibration (WBV) and ergonomic risk factors (drivers of earth moving machines, fork-lift truck drivers, truck drivers, bus drivers). The control group consisted of a small sample of 30 fire inspectors not exposed to WBV. Personal, occupational and health histories were collected by means of a structured questionnaire. Vibration measurements were performed on representative samples of the machines and vehicles used by the driver groups. From the vibration magnitudes and exposure durations, alternative measures of vibration dose were estimated for each subject. Daily vibration exposure, expressed in terms of 8-h energy-equivalent frequency-weighted acceleration, A (8), averaged 0.28–0.61 (range 0.10–1.18) m s −2 rms in the driver groups. Duration of exposure to WBV ranged between 1 and 41 years. The 7-day and 12-month prevalence of LBP was greater in the driver groups than in the controls. In the professional drivers, the occurrence of 12-month LBP, high intensity of LBP (Von Korff pain scale score ⩾5), and LBP disability (Roland & Morris disability scale score ⩾12) significantly increased with increasing cumulative vibration exposure. Even though several alternative measures of vibration exposure were associated with LBP outcomes, nevertheless a more regular trend of association with LBP was found for vibration dose expressed as ∑ a vi t i (m s −2 h), in which the frequency-weighted acceleration, a v , and lifetime exposure duration, t , were given equal weight. In multivariate data analysis, individual characteristics (e.g. age, body mass index) and a physical load index (derived from combining manual materials handling and awkward postures) were significantly associated with LBP outcomes, while psychosocial work factors (e.g. job decision, job support) showed a marginal relation to LBP. This study tends to confirm that professional driving in industry is associated with an increased risk of work-related LBP. Exposure to WBV and physical loading factors at work are important components of the multifactorial origin of LBP in professional drivers.

Objectives: To evaluate process and outcome of a multifaceted occupational health intervention programme on whole-body vibration (WBV) in forklift truck drivers. Methods: An experimental pretest/post-test control group study design. The authors trained occupational health services (OHS) in the experimental group in the use of the programme. OHS in the control group were asked to deliver care as usual. In total, 15 OHS, 32 OHS professionals, 26 companies, and 260 forklift drivers were involved. Post-test measurements were carried out one year after the start of the programme. Results: Baseline data before the start of the programme showed no difference between experimental and control group. Results of the outcome evaluation indicate a slight, although not statistically significant, reduction of WBV exposure in the experimental group (p = 0.06). Process evaluation revealed a positive influence on company policy toward WBV, attitude and intended behaviour of forklift drivers, and a trend towards an increase in knowledge of OHS professionals and company managers. The number of observed control measures with a major impact (levelling of surface and reduction of speed) was rather low. In those cases where control measures had been taken, there was a significant reduction in WBV exposure. This limited effect of the programme might be caused by the short period of follow up and the dropout of participants. The feasibility and the usefulness of the programme within the OHS setting were rated good by the participants. Conclusions: This programme to decrease WBV exposure was partially effective. Significant effects on intermediate objectives were observed. More research on the effectiveness of intervention in the field of WBV is needed.

Job hazards and preventive measures for workers Since the beginning of the Christian era, the Apuanian Alps between the provinces of Massa Carrara and Lucca in Tuscany, have been a centre for the excavation of white marble, venato and arabescato, and Cardoso stone. Marble is a metamorphic rock composed of calcium carbonate with a quartz content of less than 1%. Cardoso stone (from the name of the village of Cardoso) is a dark grey metamorphic sandstone made up of alternate thin layers of microgranular quartz and carbonate, as well as lamellas of disorientated mica, for example muscovite, with a quartz content of 60%. They are precious materials, used in Italy and worldwide to cover surfaces and flooring or as an architectural or structural element in building and for the realisation of sculptures. To prevent, as much as possible, the alteration or breakage of the material, the methods used for extracting this stone are different to those adopted for the extraction of rocks used in the building or chemical industry. The quarrying industry in the Apuanian Alps directly employs about 1000 workers in the area of Massa Carrara and 200 in Alta Versilia (a small mountainous area in the Province of Lucca), including the transporters of the extracted material from the quarries to the processing and commercialisation locations. The workers are exclusively male. To be a quarryman, specific professionalism is required, only attained with a long apprenticeship in the local quarries. In Alta Versilia the average age of the quarrymen is about 40 years and the specific length of service is high (over 10 years). In the same area, the excavation, or to use the formal term “exploitation”, is carried out at an altitude between 200 and 1600 metres above sea level. Because of the altitude some quarries close during the …

Aims: To follow up vibration induced white finger (VWF) in a selected group of 73 vibration exposed workers who claimed unsuccessfully for VWF compensation at a first examination. Methods: The VWF claimants were sent to our unit by the National Insurance Institute. The basic compensatory criteria included a positive history of VWF and abnormal cold response of the digital arteries. Following the first unsuccessful examination, over a mean time period of 4.1 (range 1–11) years the National Insurance Institute requested a second examination for all 73 claimants and a third examination for 29. During the follow up period, all subjects continued to work with vibratory tools. Results: There were 14 new cases who reported white finger during the follow up period. In the new VWF cases, finger blanching attacks became visible after about 3.5 years since the first examination. All incident cases of anamnestic VWF showed an abnormal cold response in the digital arteries and obtained compensation according to the basic compensatory criteria. In the entire sample of VWF claimants, there was a discrepancy between positive history of VWF symptoms at medical interview (55%) and abnormal cold provocation outcomes (19%). Digital arterial hyperresponsiveness to cold was associated with both VWF symptoms and the duration of vibration exposure since the first examination. Over the follow up period, a significant increase in the vasoconstrictor response to cold was observed in the vibration exposed workers with no symptoms of finger whiteness. Abnormal cold response was not associated with either age or smoking habit. Conclusions: Cold test measuring finger systolic blood pressure may be considered a useful laboratory method to confirm objectively VWF symptoms and to disclose abnormal cold induced vasoconstrictor response in vibration exposed workers with a negative history of VWF. Medical interview outcomes should be interpreted with caution in medicolegal situations involving VWF claimants.

Objectives: A case–control study was conducted in Verona, Italy, to assess the relationship between occupation, occupational exposures and systemic sclerosis (SSc). Methods: Fifty-five cases (46 female and nine male) and 171 controls were recruited. Interviews provided work histories, including job titles, industry and likelihood of occupational exposure to silica, hand– arm vibration, organic solvents, and other chemicals. Odds ratios (ORs) and 95% confidence intervals (95% CI) were estimated. Results: Female teachers (OR 3.4, 95% CI 1.2–10.1) and textile workers (OR 2.1, 95% CI 1.0–4.6) were at an increased risk of SSc. Compared with those never exposed, age-adjusted and gender-adjusted ORs were 2.3 (95% CI 1.0–5.4) among subjects exposed to organic solvents, 2.5 (95% CI 0.8–8.0) for exposure to selected chemicals, 1.7 (95% CI 0.4–7.6) for exposure to silica, and 1.5 (95% CI 0.5–4.8) for usage of vibrating tools. When data analysis was stratified according to gender, only men showed a significant increase in risk for exposure to solvents and selected chemicals. Conclusions: The findings of this study tend to support the role of organic solvents and certain chemicals in SSc causation. The association with teaching and working in the textile industry suggests that other exposures are involved in the aetiology of SSc among women. However, because of the small number of subjects, particularly in stratified analyses, chance cannot be ruled out as an explanation of some findings of this study.

Aims: To investigate alternative relations between cumulative exposures to hand-transmitted vibration (taking account of vibration magnitude, lifetime exposure duration, and frequency of vibration) and the development of white finger (Raynaud's phenomenon). Methods: Three previous studies have been combined to provide a group of 1557 users of powered vibratory tools in seven occupational subgroups: stone grinders, stone carvers, quarry drillers, dockyard caulkers, dockyard boilermakers, dockyard painters, and forest workers. The estimated total operating duration in hours was thus obtained for each subject, for each tool, and for all tools combined. From the vibration magnitudes and exposure durations, seven alternative measurements of cumulative exposure were calculated for each subject, using expressions of the form: dose = ∑amiti, where ai is the acceleration magnitude on tool i, ti is the lifetime exposure duration for tool i, and m = 0, 1, 2, or 4. Results: For all seven alternative dose measures, an increase in dose was associated with a significant increase in the occurrence of vibration-induced white finger, after adjustment for age and smoking. However, dose measures with high powers of acceleration (m > 1) faired less well than measures in which the weighted or unweighted acceleration, and lifetime exposure duration, were given equal weight (m = 1). Dose determined solely by the lifetime exposure duration (without consideration of the vibration magnitude) gave better predictions than measures with m greater than unity. All measures of dose calculated from the unweighted acceleration gave better predictions than the equivalent dose measures using acceleration frequency-weighted according to current standards. Conclusions: Since the total duration of exposure does not discriminate between exposures accumulated over the day and those accumulated over years, a linear relation between vibration magnitude and exposure duration seems appropriate for predicting the occurrence of vibration-induced white finger. Poorer predictions were obtained when the currently recommended frequency weighting was employed than when accelerations at all frequencies were given equal weight. Findings suggest that improvements are possible to both the frequency weighting and the time dependency used to predict the development of vibration-induced white finger in current standards.

Study objectives Inhalation of harmful substances is common in the workplace. The purpose of this study was to describe the epidemiology of fatal occupational inhalations in the United States. Design Data from the Census of Fatal Occupational Injuries from 1992 to 1998 were analyzed. Information on demographic characteristics, occupation, and industry was used to calculate specific mortality rates, and the inhaled substances were identified. Results Nationwide, there were 523 cases of fatal occupational inhalation, with a mortality rate of 0.56 deaths per 1,000,000 worker-years. The rate of death was greater for men (1.01/1,000,000) than for women (0.03/1,000,000), and workers ≥ 65 years of age had the highest mortality. Mining was the industry with the highest mortality rate (6.64/1,000,000). The occupations with the highest rate were firefighters (3.54/1,000,000) and farming, forestry, and fishing occupations (2.84/1,000,000). Nearly half of the inhalation victims were constructing, repairing, cleaning, inspecting, or painting when the injury occurred. Overall, carbon monoxide was the most frequently inhaled substance (33.5%). The incidence of fatal carbon monoxide inhalations was twice as high in the winter as in the summer. The proportion of workers killed by carbon monoxide poisoning increased with increasing age. Conclusions Work-related inhalations cause more deaths than any other mode of exposure to harmful substances. Recognizing those circumstances that pose a higher risk for maintenance and repair workers, as well as upgrading carbon monoxide poisoning prevention programs, could have a major impact in reducing fatal work-related inhalation injuries.

The occurrence of several types of low back pain (LBP) was investigated by a standardized questionnaire in a group of 219 port machinery operators exposed to whole-body vibration (WBV) and postural load and in a control group of 85 maintenance workers employed at the same transport company. The group of port machinery operators included 85 straddle carrier drivers, 88 fork-lift truck drivers, and 46 crane operators. The vector sum of the frequency-weighted r.m.s. acceleration of vibration measured on the seatpan of port vehicles and machines averaged 0·90 m/s 2 for fork-lift trucks, 0·48 m/s 2 for straddle carriers, 0·53 m/s 2 for mobile cranes, and 0·22 m/s 2 for overhead cranes. The 12-month prevalence of low back symptoms (LBP, sciatic pain, treated LBP, sick leave due to LBP) was significantly greater in the fork-lift truck drivers than in the controls and the other two groups of port machinery operators. After adjusting for potential confounders, the prevalence of low back symptoms was found to increase with the increase of WBV exposure expressed as duration of exposure (driving years), equivalent vibration magnitude (m/s 2 ), or cumulative vibration exposure (yr m 2 /s 4 ). An excess risk for lumbar disc herniation was observed in the port machinery operators with prolonged driving experience. In both the controls and the port machinery operators, low back complaints were strongly associated with perceived postural load assessed in terms of frequency and/or duration of awkward postures at work. Multivariate analysis showed that vibration exposure and postural load were independent predictors of LBP. Even though the cross-sectional design of the present study does not permit firm conclusions on the relationship between WBV exposure and low back disorders, the findings of this investigation provide additional epidemiological evidence that seated WBV exposure combined with non-neutral trunk postures, as while driving, is associated with an increased risk of long-term adverse health effects on the lower back.

Objective To investigate the association between scleroderma (systemic sclerosis; SSc) and reproductive factors in a hospital-based case–control study conducted at the University Hospital of Verona in Northeastern Italy. Methods Forty-six confirmed cases of SSc in women (42 with diffuse SSc and 4 with limited SSc) and 153 female control subjects with orthopedic disorders were recruited at the University Hospital. For each subject, information on age at first pregnancy, number of children and abortions, and use of oral contraceptives was obtained by means of a structured questionnaire, and information on the subject's occupational history and lifestyle factors was also sought. Results Parous women had a reduced risk of SSc (age-adjusted odds ratio [OR] 0.3, 95% confidence interval [95% CI] 0.1–0.8) compared with nulliparous women. The risk decreased with an increasing number of children: the age-adjusted OR was 0.6 (95% CI 0.2–1.7) for those women who had had 1 child, 0.3 (95% CI 0.1–0.7) for those having had 2 children, and 0.3 (95% CI 0.1–0.8) for those having had 3 or more children. Abortive pregnancies were inversely related to SSc risk: for women who had an abortion, the OR was 0.5 (95% CI 0.2–1.5) compared with women with no history of abortion. The overall history of any pregnancy (abortive or age-adjusted complete) was associated with a reduced risk of SSc (age-adjusted OR 0.3, 95% CI 0.1–0.7). Conclusion Since the incidence of SSc is higher in women and has its peak after childbearing age, it has been hypothesized that immunobiologic modifications during pregnancy may be associated with SSc development. Our findings showing a reduced risk of SSc among parous women seem to exclude the possibility of pregnancy itself as a risk factor for SSc. The role of HLA compatibility between the mother and the fetus, however, should be evaluated in further research.

There is strong epidemiological evidence that occupational exposure to WBV is associated with an increased risk of low back pain (LBP), sciatic pain, and degenerative changes in the spinal system, including lumbar intervertebral disc disorders. A prototype health surveillance scheme for WBV is presented in this paper. Surveillance is the collection, analysis, and dissemination of data for the purpose of prevention. The aims are to assess health status and diagnose vibration-induced disorders at an early stage, to inform the workers on the potential risk associated with vibration exposure, to give preventive advice to employers and employees and to control whether preventive measures which have been taken, were successful. It is suggested that a pre-placement health examination should be offered to each worker who will be exposed to WBV so as to make the worker aware of the hazards, to obtain baseline health data, and to identify medical conditions that may increase the risk due to WBV. The case history should focus on personal history, work history, and leisure activities involving driving of vehicles. The personal medical history should detail back pain complaints, disorders in the spine, any injuries or surgery to the musculoskeletal system. A physical examination on the lower back should be performed on workers who have experienced LBP symptoms over the past 12 months. The preplacement examination should be followed by periodic health reassessment with a regular interval according to the legislation of the country. It is suggested that periodic medical examination should be made available at least every 2 years to all workers who are exposed to WBV. Any change in vibration exposure at the workplace should be reported by the employer. If an increase in vibration exposure or a change in health status have occurred, the medical re-examination should be offered at shorter intervals at the discretion of the attending physician. There should be a periodic medical examination, which includes recording any change in exposure to WBV. The findings for the individual should be compared with previous examinations. Group data should also be compiled periodically. Medical removal may be considered along with re-placement in working practices without exposure to WBV. This paper presents opinions on health surveillance for whole-body vibration developed within a working group of partners funded on a European Community Network (BIOMED2 concerted action BMH4-CT98-3251: Research network on detection and prevention of injuries due to occupational vibration exposures). The health surveillance protocol and the draft questionnaire with explanation comments are presented for wider consideration by the science community and others before being considered appropriate for implementation.

OBJECTIVES—To investigate the acute response of finger circulation to vibration with different combinations of magnitude and duration but with the same "energy equivalent" acceleration magnitude according to current standards for hand transmitted vibration. METHODS—Finger skin temperature (FST) and finger blood flow (FBF) were measured in the middle fingers of both hands of 10 healthy men who had not used hand held vibrating tools regularly. With a static load of 10 N, the right hand was exposed to 125 Hz vibration with the following unweighted root mean square (rms) acceleration magnitudes and durations of exposure: 44 m/s2 for 30 minutes; 62 m/s2 for 15 minutes; 88 m/s2 for 7.5 minutes; 125 m/s2 for 3.75 minutes; and 176 m/s2 for 1.88 minutes. These vibration exposures produce the same 8 hour energy equivalent frequency weighted acceleration magnitude (~1.4 m/s2 rms) according to international standard ISO 5349 (1986). Finger circulation was measured in both the right (vibrated) and the left (non-vibrated) middle fingers before application of the vibration, and at fixed intervals during exposure to vibration and during a 45 minute recovery period. RESULTS—The FST did not change during exposure to vibration, whereas vibration with any combination of acceleration magnitude and duration produced significant percentage reductions in the FBF of the vibrated finger compared with the FBF before exposure (from −40.1% (95% confidence interval (95% CI) −24.3% to −57.2%) to −61.4% (95% CI −45.0% to −77.8%). The reduction in FBF during vibration was stronger in the vibrated finger than in the non-vibrated finger. Across the five experimental conditions, the various vibration stimuli caused a similar degree of vasoconstriction in the vibrated finger during exposure to vibration. There was a progressive decrease in the FBF of both fingers after the end of exposure to vibration with acceleration magnitudes of 44 m/s2 for 30 minutes and 62 m/s2 for 15 minutes. Significant vasoconstrictor after effects were not found in either finger after exposure to any of the other vibration stimuli with greater acceleration magnitudes for shorter durations. CONCLUSIONS—For the range of vibration magnitudes investigated (44 to 176 m/s2 rms unweighted; 5.5 to 22 m/s2 rms when frequency weighted according to ISO 5349), the vasoconstriction during exposure to 125 Hz vibration was independent of vibration magnitude. The after effect of vibration was different for stimuli with the same energy equivalent acceleration, with greater effects after longer durations of exposure. The energy equivalent acceleration therefore failed to predict the acute effects of vibration both during and after exposure to vibration. Both central and local vasoregulatory mechanisms are likely to be involved in the response of finger circulation to acute exposures to 125 Hz vibration. Keywords: finger circulation; energy equivalent acceleration magnitude; vibration frequency; magnitude; and duration

Allergic contact dermatitis is preceded by a clinically silent phase of sensitisation. In this study, we investigated whether the expression levels of six genes were related to nickel exposure and ⁄or nickel sensitisation, and whether they could predict allergic manifestations to nickel. The mRNA expression level of six genes involved in cell growth (PIM1 and ETS2), metabolism ⁄synthesis (HSD11B1 and PRDX4), apoptosis (CASP8) and signal transduction (CISH) was investigated by means of quantitative real-time RT-PCR in a cohort of 110 subjects, including healthy controls (n = 51), nickel-exposed workers (n = 23) and patients allergic to nickel (n = 36). Our findings show that the expression levels of the analysed genes did not differ between allergic patients and healthy controls, while higher expression levels of ETS2 and CASP8 were detected in the nickel- exposed workers. Changes in ETS2 and CASP8 expression are likely to be related to nickel exposure rather than to allergy.

OBJECTIVES—To investigate the occurrence of work related respiratory symptoms and to assess the effect of atopy in a group of trainee bakers. METHODS—A prospective study of work related respiratory symptoms among 125 trainee bakers who were investigated with a questionnaire plus skin prick test with wheat flour and α-amylase allergens at baseline and then after 6, 18, and 30 months. RESULTS—At the baseline examination, four students (3.2%) complained of respiratory symptoms (cough and rhinitis) when working with flours and four were skin positive to wheat flour or α-amylase. The incidence of work related respiratory symptoms was 3.4% at 6 months, and the cumulative incidence was 4.8% and 9.0% at 18 and 30 months, respectively. The incidence of skin sensitisation to occupational allergens was 4.6% at 6 months and the cumulative incidence was 4.6% at 18 months and 10.1% at 30 months. The generalised estimating equation approach to longitudinal data showed that work related respiratory symptoms in the study population was significantly associated with a personal history of allergic disease (odds ratio (OR) 5.8, 95% confidence interval (95% CI) 1.8 to 18.2) and skin sensitisation to wheat flour or α-amylase (OR 4.3, 95% CI 1.2 to 14.9). Atopy based on prick test was not related to the occurrence of work related respiratory symptoms over time (OR 1.1, 95% CI 0.3 to 3.8). CONCLUSIONS—Personal history of allergic disease is a predisposing factor for the development of symptoms caused by exposure to wheat flour and may be a criterion of unsuitability for starting a career as a baker. Atopy based on the skin prick test is useful for identifying subjects with allergic disease, but should not be used to exclude non-symptomatic atopic people from bakery work. Keywords: follow up study; wheat flour; α-amylase sensitisation; work related respiratory symptoms

Objectives: To compare the accuracy of several finger systolic blood pressure indices (FSBPIs) for the diagnosis of cold-induced Raynaud's phenomenon in vibration-exposed worker groups with different prevalences of vibration-induced white finger (VWF). Methods: The finger systolic blood pressure (FSBP) in a test finger at 10 °C as a percentage of the pressure at 30 °C, corrected for the change in systolic blood pressure in a reference finger [FSBPI(A)] or the arm [FSBPI(B)], was measured in 455 healthy controls and 874 workers exposed to hand-transmitted vibration (HTV). The following FSBPIs were also calculated: FSBPI(C), as the ratio between FSBP in the test finger at 10 °C and FSBP in the same finger at 30 °C; and FSBPI(D), as the ratio of FSBP to arm systolic blood pressure during finger cooling to 10 °C. The finding of zero systolic blood pressure, FSBP(0), in the cooled finger was taken as an objective sign of Raynaud's attack with complete closure of the digital arteries. Results: On a group basis, all FSBPIs could discriminate between the controls and the HTV workers. In the vibration-exposed worker population, the FSBPIs were significantly lower in the subjects affected with VWF than in those without vasospastic symptoms. The lower normal limits of FSBPIs were derived from the results of the cold test in the controls and were found to vary from 50% to 60%. The FSBPI(A) showed the best sensitivity for the detection of cold-induced digital arterial hyperresponsiveness in both the total sample of HTV workers (sensitivity 87%) and most of the vibration-exposed groups with different prevalence of VWF (sensitivity from 79% to 100%). The results of the receiver operating characteristic analysis suggested a higher diagnostic accuracy of FSBPI(A) when compared with the global performance of the other FSBPIs. In the whole sample of HTV workers, the predictive value of a positive cold test varied from 73% [FSBPI(D)] to 89% [FSBP(0)] and that of a negative test ranged between 89% [FSBP(0)] and 97% [FSBPI(A)]. Conclusions: The findings of this investigation and clinical experience suggest that a discriminating threshold of FSBPI(A)

Objectives: To investigate neural conduction in the upper limbs of symptomatic forestry workers with and without exposure to hand-transmitted vibration. A further aim was to assess the possible relationships between vibration exposure, nerve conduction and finger circulation in the forestry workers who used chain saws. Methods: A detailed neurophysiological investigation was performed on the upper extremities of 20 chain saw workers, 20 forestry operators with heavy manual work but without vibration exposure, and 20 healthy male controls. All subjects were screened to exclude polyneuropathy. Measurements of sensory and motor nerve conduction (velocity and amplitude) were obtained bilaterally from the median, ulnar and radial nerves. To assess peripheral vascular function, the forestry workers underwent a cold test with plethysmographic measurement of finger systolic blood pressure (FSBP). In the chain saw operators, vibration exposure was evaluated according to the International Standard ISO 5349. Indices of daily vibration exposure and lifetime cumulative vibration dose were estimated for each chain saw operator. Results: Sensory nerve conduction in several segments of the median and radial nerves was significantly reduced in the chain saw operators compared with that in the workers doing heavy manual work and the controls. The neurophysiological pattern more frequently observed in the chain saw operators was a multifocal nerve conduction impairment to several neural segments with predominant involvement of sensory rather than motor fibres. Sensory nerve conduction velocities in the hands of the chain saw operators were inversely related to both daily and lifetime cumulative vibration exposures. In the vibration-exposed forestry workers, neither were sensori-motor complaints associated with vascular symptoms (finger whiteness) nor were electrophysiological data related to cold-induced changes in FSBP. Conclusions: Exposure to hand-transmitted vibration, in addition to ergonomic stress factors, can contribute to peripheral nerve disorders occurring in forestry workers who operate chain saws. The findings of this study suggest the existence of an exposure-effect relationship for vibration-induced neuropathy. Different underlying mechanisms are likely to be involved in the pathogenesis of the neurological and vascular components of the hand-arm vibration syndrome.

Objective: The aim of this study was to eval- uate the outcome of the specific inhalation challenge test (SIC) in 160 subjects with suspected baker's asthma and to assess its relation to total flour dust levels and to personal characteristics such as specific skin sensitisa- tion, non-specific bronchial hyper-responsiveness (NSBH) and atopy. Methods: We investigated the out- come of SIC tests performed with wheat flour in six Italian laboratories. For each subject, data was available regarding skin sensitisation to wheat flour, NSBH, ato- py, forced expiratory volume at 1 s (FEV1) monitoring and airborne flour dust in the challenge chamber mea- sured by the gravimetric method (total dust in mg/m 3 ). Results: The SIC test was positive for early asthma in 42 subjects (26%) and for late/dual asthma in 18 (11%). Positive outcome to SIC was significantly associated with NBSH (odds ratio, OR: 3.5, 95% CI: 1.6-7.7) and skin sensitisation to wheat flour (OR: 3.1, 95% CI: 1.3- 7.0). Exposure level to wheat flour was less than or equal to 10 mg/m 3 in 12% of individuals, ranged between 11 and 30 mg/m 3 in 43% and exceeded 30 mg/m 3 in 45%. The outcome of SIC was always negative among workers not skin sensitised to wheat flour and without NSBH and atopy. An increasing prevalence of positive SIC was observed among workers with one or more of the above-mentioned personal characteristics whose challenge exposure was greater than 10 mg/m 3 (P < 0.001). Conclusion: Procedures currently adopted for wheat flour dust exposure during SIC need to be better standardised in order to avoid excessive airborne dust exposure. Over-exposure seems to be of no use for the diagnosis and risks making the asthmatic reaction worse, particularly in patients who are both sensitised to wheat allergens and have NSBH and/or atopy.

Objectives Changes in finger circulation were studied during and after acute exposure to increasing magnitudes of hand-transmitted vibration. Methods Finger skin temperature (FST) and finger blood flow (FBF) were measured in the middle fingers of both hands of 10 healthy men. The right hand was exposed for 15 minutes to 125-Hz vibration with acceleration magnitudes of either 5.5, 22, 44, or 62 m/s2 root-mean-square. The measures of finger circulation were taken before the vibration, at fixed intervals during exposure, and during a 45-minute recovery period. Results The FST did not change during vibration exposure, whereas vibration of any magnitude provoked significant reductions in the FBF of the vibrated finger when compared with the preexposure FBF and the contralateral (nonvibrated finger) FBF. Vasoconstrictor aftereffects (ie, during recovery) were observed in both fingers after the end of exposure to vibration magnitudes greater than 22 m/s2 root-mean-square. The higher the vibration magnitude, the stronger the reduction of FBF in either finger during both vibration exposure and the recovery period. This effect was stronger in the vibrated finger than in the nonvibrated finger during both periods. Conclusion Acute exposure to 125-Hz vibration can reduce FBF in both the vibrated and the nonvibrated finger, and the degree of digital vasoconstriction is related to the magnitude of the vibration. The pattern of the hemodynamic changes during and after vibration exposure suggests that complex vasomotor mechanisms are involved in the response of digital vessels to acute vibration.

Objective : The aim of the study was to assess peripheral neural involvement induced by exposure to hand-arm vibration. Methods : Twenty lumberjacks, working regularly with chain-saws and exposed to hand-arm vibration (group E) and 20 forestry workers performing heavy manual work and not exposed to vibration (group NE) were matched with a control group of 20 healthy non-manual workers (group C). The subjects of groups E and NE, all symptomatic, and of group C underwent extensive bilateral neurophysiological examination consisting of: sensory conduction (velocity and amplitude) of radial, median and ulnar nerves in digit-wrist segments; sensory conduction (velocity) of median nerve in wrist-elbow segment; mixed conduction (velocity and amplitude) of median and ulnar nerves in palm-wrist segments; motor conduction velocity, including distal motor latencies, and amplitude of median (elbow-wrist) and ulnar (elbow-wrist and across the elbow) nerves. Results : Electrophysiological abnormalities were found in 85% of group E's limbs, versus 62.5% of group NE's limbs. The most frequent pathological pattern in group E was a ‘multifocal' impairment (multiple sites of several nerve segments), with a prevalent involvement of sensory rather than motor fibres in the hand, seldom extending to the forearm. Multivariate analysis showed that the neurographic parameters which better characterized workers exposed to hand-arm vibration had a pattern different from that usually found in idiopathic carpal tunnel syndrome (CTS). Conclusion : These results suggest that vibration-induced neural involvement can be considered neither pure digital neuropathy, nor definite CTS, as previously described.

The complex of vascular, neurologic, and osteoarticular disorders occurring in the upper limbs of vibration-exposed workers is called hand-arm vibration syndrome. There is epidemiologic evidence for an increased occurrence of peripheral sensorineural disorders in occupational groups working with vibrating tools. An excess risk for wrist osteoarthrosis and for elbow arthrosis and osteophytosis has been reported in workers exposed to shocks and low-frequency vibration of high magnitude from percussive tools. However, there are too few epidemiology data to enable reliable conclusions to be drawn about exposure-response relationships for both sensorineural disturbances and bone and joint disorders caused by hand-transmitted vibration. Cross-sectional and longitudinal epidemiology studies have shown that occupational exposure to hand-transmitted vibration from a great variety of hand-held tools is significantly associated with an increased occurrence of digital vasospastic disorders called vibration-induced white finger (VWF). The proposal of an exposure-response relationship for VWF has been included in an annex to the international standard ISO 5349. The findings of several epidemiology studies have shown a poor agreement between the risk for VWF observed in various occupational groups and that predicted by the ISO 5349 model. Both overestimation and underestimation of the occurrence of VWF have been reported by investigators. It has been argued that the current ISO frequency-weighting curve for hand-transmitted vibration may be inappropriate for the assessment of vibration-induced adverse vascular effects. Alternative exposure-response relationships for VWF have been suggested in recent epidemiology studies. The epidemiology data used to construct current exposure-response relationships for vibration-induced injuries are primarily derived from cross-sectional studies. Future epidemiology research should be based on prospective cohort studies because the design characteristics of such studies permit the study of cause-effect relationships and the formulation of etiologic hypotheses.

Objectives This study investigated changes in finger circulation after different durations of exposure to hand-transmitted vibration. Methods Finger skin temperature (FST), finger blood flow (FBF), and finger systolic blood pressure (FSBP) were measured, the latter two by strain gauge plethysmography, in the middle fingers of both hands of 10 healthy men. Finger vascular resistance was also estimated. The right hand was exposed for 7.5, 15, and 30 minutes (static load 10 N) to 125-Hz vibration (root-mean-square acceleration 87 m/s2). Static load only was used as a control. Finger circulation was measured before the vibration and static load exposure and at fixed intervals during exposure and a 45-minute recovery period. Results No significant changes were found with the static load. The FST and FSBP did not change significantly during vibration exposure, whereas vibration produced significant reductions in FBF and increases in vascular resistance at each duration when compared with preexposure and contralateral (nonvibrated) finger values. Temporary vasodilation occurred in the vibrated finger immediately after each vibration exposure. Recovery was complete for FBF and vascular resistance after the 7.5-min vibration, whereas a progressive FBF reduction occurred in both the vibrated and the nonvibrated fingers during the second half of the recovery periods after 15- and 30-min exposure. The longer the duration of vibration exposure, the stronger the vasoconstriction in the vibrated finger during recovery. Conclusion Vasoregulatory mechanisms mediated by both intrinsic (local) and extrinsic (neural or endocrine) control systems seem to be related to digital circulatory changes during 125-Hz vibration. These findings support previous investigations suggesting that, not only the frequency and magnitude of vibration, but also its duration contributes to the reaction of the digital vessels to acute vibration.

Objectives: To investigate the occurrence of vibration-induced white finger (VWF) and the cold response of digital vessels in a group of 68 forestry workers who underwent a first clinical examination in 1990 and were then reexamined in 1995. Methods: The forestry workers were divided into three groups: group A (n = 27), active workers who did not have VWF in␣1990 and continued to use chain saws; group B (n = 29), workers who did not have VWF in 1990 and retired before 1995; and group C (n = 12), active or retired workers who had VWF in 1990. The subjects underwent a medical interview, a complete physical examination, and a cold provocation test, which were performed by the same physicians at both surveys. The cold test consisted of measurement of the finger systolic blood pressure (FSBP) after local cooling to 10 °C, expressed as a percentage of the pressure recorded at 30 °C (FSBP%10°). Results: Three new cases of VWF occurred during the follow-up period among workers who had used only antivibration (AV) chain saws. The vasoconstrictor response to cold was unchanged in group A and improved in group B (P < 0.001). A significant decrease in VWF symptoms and abnormal response to cold was observed in group C (P < 0.05). As a result of preventive measures curtailing saw usage time in the VWF workers, the daily vibration exposure in group C was lower in 1995 than in 1990 (P = 0.02). In the retired workers, FSBP%10° was positively related to the time since the cessation of work with chain saws (P < 0.01). Conclusions: The findings of this follow-up study indicate that a reduction in or cessation of exposure to vibration has a beneficial effect on finger-blanching symptoms and the cold response of digital vessels. The occurrence of new cases of VWF in subjects whose work experience was limited to AV chain saws argues for the maintenance of health surveillance in these workers.

Study objectives To determine whether intensity, duration, age at initiation, and cessation of cigarette smoking act differently in the development of various histologic types of lung cancer. Design: A case-control study among deceased men who underwent autopsy, a procedure that involves approximately 73% of all local deaths. Setting The Province of Trieste in northeastern Italy Participants Seven hundred fifty-five patients with lung cancer, including 267 with squamous cell carcinoma, 218 with small cell carcinoma, 90 with large cell carcinoma, 158 with adenocarcinoma, and 22 with other histologic types, and 755 control subjects who had died of causes other than chronic lung diseases and certain tumors. Information on smoking habits, residential history, and occupational exposure was obtained from each subject's next of kin. Results Compared with nonsmokers, the odds ratio (OR) for current smokers was 13.4 for all types combined, 18.8 for squamous cell carcinoma, 14.3 for small cell carcinoma, 34.3 for large cell carcinoma, and 7.9 for adenocarcinoma. Intensity of smoking, duration, age at starting, and dose were all directly associated with all histologic types of lung cancer, although the OR was lower for adenocarcinoma than for other cell types. When results were restricted to ever smokers, exposure-response curves were similar across histologic types. The risk of lung cancer attributable to smoking was 88% for all types combined, 91% for squamous cell carcinoma, 89% for small cell carcinoma, 95% for large cell carcinoma, and 82% for adenocarcinoma. Conclusions This study confirms that cigarette smoking causes all types of lung cancer, but the proportion of cases attributable to smoking is lower for adenocarcinoma than for other types, due to a higher proportion of nonsmokers.

OBJECTIVES: To investigate the changes over a workshift in fingertip tactile perception thresholds in users of impact wrenches exposed to intermittent hand transmitted vibration. A further aim was to assess the relation between acute changes in tactile sensation, sensorineural disorders, and vibration dose. METHODS: The study populations consisted of 30 workers exposed to vibration (16 men and 14 women) and 25 control manual workers (10 men and 15 women). Sensorineural disorders in the fingers and hands were graded according to the staging system of the Stockholm workshop scale. Tactile function was tested by measuring aesthesiometric thresholds (two point discrimination and depth sense perception) and vibrotactile perception thresholds at 16, 31.5, and 125 Hz before and after a workshift. Temporary threshold shift was then calculated as the difference between threshold measures before and after the shift. The measurement and assessment of exposure to vibration were made according to the international standard ISO 5349. The vibration dose accumulated over a workshift (m2s-4h) was estimated for each user of impact wrenches. Daily exposure to vibration was also expressed in terms of eight hour energy equivalent frequency weighted acceleration ((ahw)eq(8) in ms-2 rms). RESULTS: After adjustment for age and alcohol consumption, vibrotactile perception thresholds before exposure were greater in the workers exposed to vibration than in the controls. No differences in aesthesiometric thresholds before the shift were found between the study groups. Sensorineural disorders were mild in the workers exposed to vibration and minor neurological abnormalities were detected at the physical examination. Owing to the intermittent use of impact wrenches, the estimated mean (ahw)eq(8) for the subjects exposed to vibration was low (1.3 ms-2 rms). A significant temporary threshold shift in vibration perception at all test frequencies was found in the workers exposed to vibration but not in the controls. A significant increase in depth sense perception thresholds was found in the men exposed to vibration. The temporary threshold shift in vibration perception at 125 Hz, and to a lesser extent at 16 and 31.5 Hz, was associated with the severity of sensorineural disorders. In the workers exposed to vibration the temporary threshold shift in vibration sense at all test frequencies was positively related to the estimated dose of vibration received over a workshift. No significant relation was found between aesthesiometric threshold changes and vibration dose. CONCLUSIONS: Intermittent exposure to hand transmitted vibration over a workshift can cause a deterioration of tactile perception in the fingers of users of impact wrenches. Acute tactile dysfunction was related to both the estimated dose of vibration and the severity of sensorineural symptoms. The temporary threshold shift in vibration perception suggested that fast adapting skin mechanoreceptors such as Pacinian and Meissner corpuscles were mainly involved in the acute sensory impairment to the fingertips of the workers exposed to vibration. Changes in tactile perception can occur in workers with daily exposure to vibration that is considered to be associated with a minimal risk of adverse health effects induced by vibration.

Clinical and autoptical studies have suggested a predisposing role of the allele E4 of apolipoprotein E (apoE) in the development of atherosclerosis and cardiovascular disease. To investigate the possible contribution of apoE allele polymorphism to the carotid intima-media thickness (IMT) as assessed by ultrasound, we studied 260 asymptomatic nondiabetic subjects (121 men, 139 women; mean±SD age, 53±7 years), randomly selected from the population register of the inhabitants of Trieste, Italy. B-mode ultrasound was used to quantify the maximum IMT at 12 sites on the near and far wall of the common, bifurcation, and internal carotid arteries. ApoE genotypes were determined from amplified apoE sequences by restriction isotyping. The frequencies of E2, E3, and E4 alleles were 0.073, 0.827, and 0.100, respectively. As expected, subjects with E4 allele had the highest levels of total serum cholesterol and LDL cholesterol, subjects with E2 allele had the lowest levels, and those with E3 genotype had intermediate levels. The echographic measurements of carotid IMT showed increasing values from E2 to E4 carriers. After adjustment for total and LDL cholesterol serum levels, triglycerides, ratio of LDL to HDL cholesterol, age, sex, and body mass index, ANCOVA showed that the common carotid IMT was significantly greater ( P =.029) in subjects with E4 allele compared with E3 carriers. Our data confirm the influence of apoE4 on cholesterol levels and clearly show that apoE genotype affects carotid atherosclerosis in its early stages in middle-aged asymptomatic subjects.