Search

This paper reports an intracavity terahertz parametric source based on the stimulated polariton scattering in RbTiOPO4 crystal with a high repetition rate and a high average power. The side pumping for the gain medium by laser diodes is adopted to get a higher fundamental power and a larger fundamental laser beam size than those in the diode-end-pumping in order to improve the THz output power. A non-collinear convex-plane fundamental cavity is adopted so that the thermal effect can be offset in some degree and the fundamental beam size is further increased. The obtained maximum average THz output power is 367 μW at 3.88 THz when the diode pump power is 105 W and the pulse repetition frequency (PRF) is 7 kHz. The terahertz power of 367 μW is the highest ever obtained in SPS sources.

The optoelectronic effects of sidewall passivation on micro-light-emitting diodes (Micro-LEDs) were investigated using sol-gel chemical synthesis. Blue InGaN/GaN multi-quantum well (MQW) Micro-LEDs, ranging in size from 20 × 20 μm to 100 × 100 μm and with high EQE, were fabricated and distinguished by the passivation method used, including no passivation, sol-gel SiO2, and plasma-enhanced chemical vapor deposition (PECVD) SiO2. Impressively, the sol-gel method is advantageous in improving the optoelectronic performance of Micro-LEDs. The fabricated 20 × 20 μm Micro-LEDs showed an EQE of 27.7% with sol-gel passivation, which was a 14% improvement compared to devices without sidewall passivation. Sol-gel sidewall passivation allows Micro-LEDs to effectively achieve sharper edge emission, superior surface luminous uniformity, and intensity, providing the possibility for the fabrication of low-cost and high-efficiency Micro-LEDs.

Micro light-emitting diode (micro-LED) will play an important role in the future generation of smart displays. They are found very attractive in many applications, such as maskless lithography, biosensor, augmented reality (AR)/mixed reality etc, at the same time. A monitor that can fulfill saturated color rendering, high display resolution, and fast response time is highly desirable, and the micro-LED-based technology could be our best chance to meet these requirements. At present, semiconductor-based red, green and blue micro-LED chips and color-conversion enhanced micro-LEDs are the major contenders for full-color high-resolution displays. Both technologies need revolutionary ways to perfect the material qualities, fabricate the device, and assemble the individual parts into a system. In this roadmap, we will highlight the current status and challenges of micro-LED-related issues and discuss the possible advances in science and technology that can stand up to the challenges. The innovation in epitaxy, such as the tunnel junction, the direct epitaxy and nitride-based quantum wells for red and ultraviolet, can provide critical solutions to the micro-LED performance in various aspects. The quantum scale structure, like nanowires or nanorods, can be crucial for the scaling of the devices. Meanwhile, the color conversion method, which uses colloidal quantum dot as the active material, can provide a hassle-free way to assemble a large micro-LED array and emphasis the full-color demonstration via colloidal quantum dot. These quantum dots can be patterned by porous structure, inkjet, or photo-sensitive resin. In addition to the micro-LED devices, the peripheral components or technologies are equally important. Microchip transfer and repair, heterogeneous integration with the electronics, and the novel 2D material cannot be ignored, or the overall display module will be very power-consuming. The AR is one of the potential customers for micro-LED displays, and the user experience so far is limited due to the lack of a truly qualified display. Our analysis showed the micro-LED is on the way to addressing and solving the current problems, such as high loss optical coupling and narrow field of view. All these efforts are channeled to achieve an efficient display with all ideal qualities that meet our most stringent viewing requirements, and we expect it to become an indispensable part of our daily life.

The underwater hyperspectral imager enables the detection and identification of targets on the seafloor by collecting high-resolution spectral images. The distance between the hyperspectral imager and the targets cannot be consistent in real operation by factors such as motion and fluctuating terrain, resulting in unfocused images and negative effects on the identification. In this paper, we developed a novel integrated underwater hyperspectral imaging system for deep sea surveys and proposed an autofocus strategy based on liquid lens focusing transfer. The calibration tests provided a clear focus result for hyperspectral transects and a global spectral resolution of less than 7 nm in spectral range from 400 to 800 nm. The prototype was used to obtain spectrum and image information of manganese nodules and four other rocks in a laboratory environment. The classification of the five kinds of minerals was successfully realized by using a support vector machine. We tested the UHI prototype in the deep sea and observed a Psychropotidae specimen on the sediment from the in situ hyperspectral images. The results show that the prototype developed here can accurately and stably obtain hyperspectral data and has potential applications for in situ deep-sea exploration.

High temperature detection is a constant challenge for condition monitoring under harsh environments in optical fiber sensors research. In this study, the temperature response characteristics of guided acoustic wave Brillouin scattering (GAWBS) spectra in silica single-mode fiber (SMF) up to 800 °C are experimentally investigated, demonstrating the feasibility of the method for high-temperature monitoring. With increasing temperature, the resonance frequency of GAWBS spectra increases in a nearly linear manner, with linearly fitted temperature-dependent frequency shift coefficients of 8.19 kHz/°C for TR2,7 mode and 16.74 kHz/°C for R0,4 mode. More importantly, the linewidth of the GAWBS spectra is observed to narrow down with increasing temperature with a linearly fitted rate of −6.91 × 10−4/°C for TR2,7 modes and −8.56 × 10−4/°C for R0,4 modes. The signal-to-noise ratio of the GAWBS spectra induced by both modes increase by more than 3 dB when the temperature rises from 22 °C to 800 °C, which indicates that the proposed sensing scheme has better performance in high-temperature environments, and are particularly suitable for sensing applications in extreme environments. This study confirms the potential of high-temperature sensing using only GAWBS in silica fibers without any complex micromachining process, which has the advantages of strong mechanical strength, simple structure, easy operation, and low cost.

Oil shale is a crucial unconventional energy source to supplement conventional oil and gas. The oil shale in the Maoming Basin of China has excellent resource potential. In this study, through systematic geochemical testing, the industrial quality and geochemical characteristics of oil shale are revealed, and the hydrocarbon generation potential of oil shale, the parent rock type, and the tectonic setting of the source area are discussed. It is comprehensively assessed that Maoming oil shale has a medium-oil yield (avg. 6.71%) with high ash content (avg. 76.1%), a high calorific value (avg. 7.16 M J/kg), and ultra-low sulfur (avg. 0.54%). The mineralogical compositions primarily consist of clay minerals and quartz, and barely pyrite. Maoming oil shale is in an immature evolution stage, with high TOC and I-II1 kerogen type, and could be considered an excellent hydrocarbon source rock. The chemical index of alteration (CIA), the index of chemical variability (ICV), and the Th/U ratio indicate that the Maoming oil shale parent rock area is strongly weathered. Multitudinous geochemical diagrams also show that the oil shale was mainly derived from Late Cretaceous felsic volcanic rock and the granite zone, and the tectonic setting was a continental island arc environment related to the active continental margin. This is consistent with the tectonic history of southern China in the Late Cretaceous.

ObjectiveThis study aims to develop and validate a CT-based radiomics nomogram integrated with clinic-radiological factors for preoperatively differentiating high-grade from low-grade clear cell renal cell carcinomas (CCRCCs).Methods370 patients with complete clinical, pathological, and CT image data were enrolled in this retrospective study, and were randomly divided into training and testing sets with a 7:3 ratio. Radiomics features were extracted from nephrographic phase (NP) contrast-enhanced images, and then a radiomics model was constructed by the selected radiomics features using a multivariable logistic regression combined with the most suitable feature selection algorithm determined by the comparison among least absolute shrinkage and selection operator (LASSO), recursive feature elimination (RFE) and ReliefF. A clinical model was established using clinical and radiological features. A radiomics nomogram was constructed by integrating the radiomics signature and independent clinic-radiological features. Performance of these three models was assessed using receiver operating characteristic (ROC) curve analysis and decision curve analysis (DCA).ResultsUsing multivariate logistic regression analysis, three clinic-radiological features including intratumoral necrosis (OR=3.00, 95% CI=1.30-6.90, p=0.049), intratumoral angiogenesis (OR=3.28, 95% CI=1.22-8.78, p=0.018), and perinephric metastasis (OR=2.90, 95% CI=1.03-8.17, p=0.044) were found to be independent predictors of WHO/ISUP grade in CCRCC. Incorporating the above clinic-radiological predictors and radiomics signature constructed by LASSO, a CT-based radiomics nomogram was developed, and presented better predictive performance than clinic-radiological model and radiomics signature model, with an AUC of 0.891 (95% CI=0.832-0.962) and 0.843 (95% CI=0.718-0.975) in the training and testing sets, respectively. DCA indicated that the nomogram has potential clinical usefulness.ConclusionThe CT-based radiomics nomogram is a promising tool to predict WHO/ISUP grade of CCRCC preoperatively and noninvasively.

Absolute measurement technology has received considerable attention in the field of optical metrology owing to its high accuracy. However, to ensure accuracy of measurement, the traditional method requires the use of expensive high-precision stages and considerable time for the precise adjustment of the measured surface. A shift-rotation absolute measurement method for irregular aperture optical surfaces based on deep learning is presented here. In this method, the measured surface needs to be tested in the original position and two randomly changed positions. Furthermore, a simple and effective shift-rotation prediction convolutional neural network that can learn the mapping relationships between the binarized images of the changed position and shift-rotation is designed. The shape of the measured surface with an irregularly shaped aperture is obtained by fitting orthogonalized Zernike polynomials. Compared with the current absolute measurement method for irregular apertures, this method is highly efficient and cost-effective for adjusting the measured surface. The simulation and experimental results demonstrate the accuracy and validity of this approach.

IntroductionSomatic copy number deletion (SCND) of CDKN2A gene is the most frequent event in cancer genomes. Whether CDKN2A SCND drives human cancer metastasis is far from clear. Hematogenous metastasis is the main reason of human gastric carcinoma (GC) death. Thus, prediction GC metastasis is eagerly awaited.MethodGC patients (n=408) enrolled in both a cross-sectional and a prospective cohorts were analysed. CDKN2A SCND was detected with a quantitative PCR assay (P16-Light). Association of CDKN2A SCND and GC metastasis was evaluated. Effect of CDKN2A SCND by CRISPR/Cas9 on biological behaviors of cancer cells was also studied.ResultsCDKN2A SCND was detected in 38.9% of GCs from patients (n=234) enrolled in the cross-sectional cohort. Association analysis showed that more CDKN2A SCND was recognized in GCs with hematogenous metastasis than those without (66.7% vs. 35.7%, p=0.014). CDKN2A SCND was detected in 36.8% of baseline pN0M0 GCs from patients (n=174) enrolled in the prospective study, the relationship between CDKN2A SCND and hematogenous metastasis throughout the follow-up period (62.7 months in median) was also significant (66.7% vs. 34.6%, p=0.016). Using CDKN2A SCND as a biomarker for predicting hematogenous metastasis of GCs, the prediction sensitivity and specificity were 66.7% and 65.4%. The results of functional experiments indicated that CDKN2A SCND could obviously downregulate P53 expression that consequently inhibited the apoptosis of MGC803 GC and HEK293T cells. This may account for hematogenous metastasis of GCs by CDKN2A SCND.ConclusionCDKN2A SCND may drive GC metastasis and could be used as a predictor for hematogenous metastasis of GCs.

Under stress conditions, luteinizing hormone (LH)-mediated ovulation is inhibited, resulting in insufficient oocyte production and excretion during follicular development. When the body is stressed, a large amount of corticosterone (CORT) is generated, which will lead to a disorder of the body’s endocrine system and damage to the body. Our previous work showed that CORT can block follicular development in mice. Since LH acts through binding with the luteinizing hormone receptor (Lhcgr), the present study aimed to investigate whether and how corticosterone (CORT) influences Lhcgr expression in mouse ovarian granulosa cells (GCs). For this purpose, three-week-old ICR female mice were injected intraperitoneally with pregnant mare serum gonadotropin (PMSG). In addition, the treatment group was injected with CORT (1 mg/mouse) at intervals of 8 h and the control group was injected with the same volume of methyl sulfoxide (DMSO). GCs were collected at 24 h, 48 h, and 55 h after PMSG injection. For in vitro experiments, the mouse GCs obtained from healthy follicles were treated with CORT alone, or together with inhibitors against the glucocorticoid receptor (Nr3c1). The results showed that the CORT caused a downregulation of Lhcgr expression in GCs, which was accompanied by impaired cell viability. Moreover, the effect of the CORT was mediated by binding to its receptor (Nr3c1) in GCs. Further investigation revealed that Nr3c1 might regulate the transcription of Lhcgr through inhibiting the expression of Lhcgr transcription factors, including AP1 and Creb. Taken together, our findings suggested a possible mechanism of CORT-induced anovulation involving the inhibition of Lhcgr expression in GCs by the CORT–Nr3c1–AP1/Creb axis.

In terahertz (THz) wave parametric sources, the large angle between the pump and terahertz waves (about 65° in LiNbO3 crystal) will affect the spatial intensity distributions. To investigate how the noncollinear phase-matching affects the spatial intensity properties of the pump, Stokes, and THz waves, we take the injection-seeded THz-wave parametric generator (is-TPG) as an example to study the beam spatial intensity properties via the numerical solutions of the coupled-wave equations. The simulated results demonstrate that the pump and Stokes intensities have significant changes along the THz-wave propagation direction. It is the first time that the spatial intensity distributions of the three waves in the THz-wave parametric sources have been studied in theory. In addition, the output intensity distributions of the pump, Stokes, and THz waves are measured in the designed is-TPG. The measured spatial intensity distributions are in coincidence with the simulated results. Investigations on the beam spatial intensity properties provide a potential approach to improve the THz-wave outputs and the pump conversion efficiency for the is-TPG and other THz-wave parametric sources.

In this letter, tin diselenide (SnSe2) was successfully prepared with the liquid-phase exfoliation method and embedded into polyvinyl alcohol as a saturable absorber (SA) in a dual-wavelength passively mode-locked Yb-doped fiber laser. Stable mode-locked pulses with a maximum average output power of 2.55 mW and a slope efficiency of 1.3% at the fundamental repetition rate of 333 kHz were achieved. By properly adjusting polarization state, four kinds of dual-wavelength fundamental frequency mode-locked pulses with peak wavelength intervals of 0.4, 1.0, 1.5, and 1.9 nm were obtained, and the corresponding waveforms with different single-pulse shapes were investigated in our work. A maximum signal-to-noise ratio of 71.04 dB indicates that SnSe2 is promising to serve as a SA in passively mode-locked fiber lasers.

We present an investigation on the intrinsic optical properties of superconducting FeSe thin films deposited on CaF2 substrates. It is found that the samples respond strongly to the near-infrared (NIR) irradiation in different temperature regimes. Thus, we are able to measure the optical reflectivity of the in-plane (ab-plane) thin films from room temperature to 5 K. A critical behavior near the superconducting transition temperature (Tc~10 K) can be observed optically in the temperature-dependent reflectivity spectrum. We carry out the Kramers-Kronig analysis of the experimental data and discuss the basic optical properties of superconducting FeSe thin films in different structural phases above and below the transition temperature Ts~100 K. By fitting experimental data with the Drude-Smith and Drude-Lorentz formulas, we obtain the key sample parameters such as the electronic relaxation time and dc conductivity. The interesting and important findings obtained from this study not only shed new light on the pairing mechanism in FeSe but also demonstrate that the NIR reflection experiment is a powerful and convenient optical technique for contactless characterization and investigation of superconducting thin film materials.

In this study, thin-film thermocouples (TFTCs) were combined with a smart bolt to design a smart bolt that can directly test high temperature in service monitoring and parameter calculation for gas turbine structure design. The first-principles calculation was used to analyze the design of the surface properties of nickel-based alloys and insulating layers, and finite element analysis was used to optimize dimension parameters by controlling the thermal stress matching of insulating layers and sensitive layers. The effect of the glass powder with different particle sizes on the microstructure of the ITO and In2O3 films was studied via SEM. The preferred particle size of the additive glass powder is 400 nm. The XRD pattern shows the (222) peak has the highest intensity. The intensities of the (222) and (622) peaks increase after the heat treatment. The calibration results show that the average Seebeck coefficient of the TFTCs can reach 64.9 μV/°C at 1100 °C with a maximum voltage of 71.4 mV. The repeatability error of the cycles of the sensor after heat treatment is ±1.05%. The repeatability of the sensor is up to 98.95%. The smart bolts were tested for application in small aero engines. It can be seen that under the impact of 1000 °C, the thermal response of the prepared smart bolt is better than that of the K-type armored thermocouple, and the thermal balance is achieved faster. The intelligent bolt sensor proposed in this work has better engineering application prospects owing to its convenience of installation in harsh environments.

To meet the need for micro-volume devices for high-precision measurement of temperature, Cu-Constantan (CuNi45) thin films with a novel array structure of thermo-electrodes were designed and fabricated. The thermo-electrodes on the probe-type substrate were deposited by magnetron sputtering technology and the profiling mask was prepared by 3D printing technology. The comprehensive performance of the temperature sensor was improved by systematic optimization of the heat treatment process and accuracy correction algorithm. Results showed that the sensor can measure with an accuracy of up to ±0.19%FS from −60 °C to 200 °C. The three-dimensional probe array temperature sensor shows great advantages in sensitivity, reliability resolution, stability, and measurement accuracy.

With the development of underwater exploration, underwater networking is in urgent demand. At present, underwater wireless optical communication (UWOC) is primarily based on line-of-sight (LOS) communication links. However, the underwater environment is so complicated that LOS communication links are easily affected by a couple of factors such as air bubbles, turbidity, oceanic turbulence, and so on. We put forward novel UWOC links using the total reflection at the air-water interface, which can mitigate those phenomena. This paper aims to investigate a UWOC link based on the total reflection at the air-water interface. In our work, we achieved the maximum data rate of 300 Mb/s and a bit error rate (BER) of 3.10 × 10−3 under the forward error correction (FEC) with the total reflection angle of 7°. Furthermore, we verified the performance of the total reflection-based UWOC links at the air-water interface in the presence of waves and evaluated the impact on the UWOC links when the frequency and amplitude of the waves varied.

High-temperature measurements above 1000 °C are critical in harsh environments such as aerospace, metallurgy, fossil fuel, and power production. Fiber-optic high-temperature sensors are gradually replacing traditional electronic sensors due to their small size, resistance to electromagnetic interference, remote detection, multiplexing, and distributed measurement advantages. This paper reviews the sensing principle, structural design, and temperature measurement performance of fiber-optic high-temperature sensors, as well as recent significant progress in the transition of sensing solutions from glass to crystal fiber. Finally, future prospects and challenges in developing fiber-optic high-temperature sensors are also discussed.

IntroductionPulmonary artery pressure (PAP) is increased and right ventricular (RV) function is well preserved in healthy subjects upon exposure to high altitude (HA). An increase in PAP may trigger notching of the right ventricular outflow tract Doppler flow velocity envelope (RVOT notch), which is associated with impaired RV function in patients with pulmonary hypertension. However, whether HA exposure can induce RVOT notch formation and the subsequent impact on cardiac function in healthy subjects remains unclear.MethodsA total of 99 subjects (69 males and 30 females) with a median age of 25 years were enrolled in this study; they traveled from 500 to 4100 m by bus over a 2-day period. All subjects underwent a comprehensive physiological and echocardiographic examination 1 day before ascension at low altitude and 15 ± 3 h after arrival at HA. The RVOT notch was determined by the presence of a notched shape in the RVOT Doppler flow velocity envelope. The systolic PAP (SPAP) was calculated as Bernoulli equation SPAP = 4 × (maximum tricuspid regurgitation velocity)2+5 and mean PAP (mPAP) = 0.61 × SPAP+2. Cardiac output was calculated as stroke volume × heart rate. Pulmonary capillary wedge pressure (PCWP) was calculated as 1.9+1.24 × mitral E/e’. Pulmonary vascular resistance (PVR) was calculated as (mPAP-PCWP)/CO.ResultsAfter HA exposure, 20 (20.2%) subjects had an RVOT notch [notch (+)], and 79 (79.8%) subjects did not have an RVOT notch [notch (−)]. In the multivariate logistic regression analysis, the SPAP, right ventricular global longitude strain (RV GLS), and tricuspid E/A were independently associated with the RVOT notch. The SPAP, mPAP, PVR, standard deviations of the times to peak systolic strain in the four mid-basal RV segments (RVSD4), peak velocity of the isovolumic contraction period (ICV), and the peak systolic velocity (s’) at the mitral/tricuspid annulus were increased in all subjects. Conversely, the pulse oxygen saturation (SpO2), RV GLS, and tricuspid annulus plane systolic excursion (TAPSE)/SPAP were decreased. However, the increases of SPAP, mPAP, PVR, and RVSD4 and the decreases of SpO2, RV GLS, and TAPSE/SPAP were more pronounced in the notch (+) group than in the notch (−) group. Additionally, increased tricuspid ICV and mitral/tricuspid s’ were found only in the notch (−) group.ConclusionHA exposure-induced RVOT notch formation is associated with impaired RV function, including no increase in the tricuspid ICV or s’, reduction of RV deformation, deterioration in RV-pulmonary artery coupling, and RV intraventricular synchrony.

BackgroundWe previously found that microbial disruption in Pseudomonas aeruginosa ventilator-associated pneumonia (PA-VAP) patients are long-lasting. Long-term microbial dysbiosis may lead to changes in metabolites. Short-chain fatty acids (SCFAs) are microbial fermentation products and show beneficial effects in patients with pneumonia. In this study, we aimed to explore the association between circulating SCFA levels and clinical outcomes in patients with PA-VAP.MethodsIn this study, we analyzed SCFAs in the serum of 49 patients with PA-VAP by gas chromatography-mass spectrometry analysis. Twenty of these patients died, and 29 survived. The correlation between serum SCFAs and patient survival and immune parameters was analyzed.ResultsWe developed a partial least squares discriminant analysis (PLS-DA) model to examine differential SCFAs in 49 patients with PA-VAP. Among the seven SCFAs, only acetic acid was increased in non-survivors (P = 0.031, VIP > 1). Furthermore, high levels of acetic acid (>1.96ug/ml) showed increased 90-day mortality compared to low levels of acetic acid (

We have investigated the thermal characteristics of InGaN-based green micro-light-emitting diodes (micro-LEDs) without the passivation layer in a wide junction temperature range of 298–453 K. The decreased temperature coefficient (dVf/dT) of the device with a smaller device size is attributed to the increased series resistances for the smaller devices, largely affected by the defects due to sidewall damage of the active layer. The ideality factor of 2.02 at 298 K suggests that the charge transport mechanism could be defect-assisted tunneling. In addition, it is observed that the ideality factor decreases with increasing temperature. The results of the C–V measurements suggest similar electron and hole concentrations in the depletion region, leading to a balanced electron–hole recombination in the active layer. It was also found that the temperature-dependent bandgaps of ternary In0.3Ga0.7N obtained from electroluminescence spectra of micro-LEDs agree with the calculated values by using the semi-empirical Varshni relationship.

Thin-Film Thermocouples (TFTCs) are characterized by their high spatial resolutions, low cost, high efficiency and low interference on the air flow. However, the thermal stability of TFTCs should be further improved for application since their accuracy is influenced by joule heat and temperature time drift. In this paper, 3D molecular dynamics and finite element analysis are used for structural design. The effects of RF magnetron sputtering power and gas flow rate on conductivity and temperature time drift rate (DT) of high thermal stability tungsten–rhenium (95% W/5% Re vs. 74% W/26% Re) TFTCs were analyzed. According to the experimental results, the average Seebeck coefficient reached 31.1 µV/°C at 900 °C temperature difference (hot junction 1040 °C) with a repeatability error at ±1.37% in 33 h. The conductivity is 17.1 S/m, which is approximately 15.2 times larger than the compared tungsten-rhenium sample we presented, and the DT is 0.92 °C/h (1040 °C for 5 h), which is 9.5% of the old type we presented and 4.5% of compared ITO sample. The lumped capacity method test shows that the response time is 11.5 ms at 300 °C. This indicated an important significance in real-time temperature measurement for narrow spaces, such as the aero-engine combustion chamber.

It is highly desirable, while still challenging, to obtain noble metal nanocrystals with custom capping ligands, because their colloidal synthesis relies on specific capping ligands for the shape control while conventional ligand exchange processes suffer from “the strong replaces the weak” limitation, which greatly hinders their applications. Herein, we report a general and effective ligand exchange approach that can replace the native capping ligands of noble metal nanocrystals with virtually any type of ligands, producing flexibly tailored surface properties. The key is to use diethylamine with conveniently switchable binding affinity to the metal surface as an intermediate ligand. As a strong ligand, it in its original form can effectively remove the native ligands; while protonated, it loses its binding affinity and facilitates the adsorption of new ligands, especially weak ones, onto the metal surface. By this means, the irreversible order in the conventional ligand exchange processes could be overcome. The efficacy of the strategy is demonstrated by mutual exchange of the capping ligands among cetyltrimethylammonium, citrate, polyvinylpyrrolidone, and oleylamine. This novel strategy significantly expands our ability to manipulate the surface property of noble metal nanocrystals and extends their applicability to a wide range of fields, particularly biomedical applications.

Oil shales are developed in the Shale Member of the Middle Jurassic Shimengou Formation in the Qaidam Basin, China. The oil shales can be classified into three quality groups (low-, medium-, and high-quality oil shales) through a comprehensive analysis protocol that includes Rock-Eval pyrolysis, total organic carbon (TOC) content, proximate analysis, gas chromatography-mass spectrometry (GC-MS), X-ray diffraction (XRD), major and trace element analyses, and maceral analysis. The low-quality oil shales mainly contain type II1 kerogen, the medium-quality oil shales mainly contain type I-II1 kerogen, and the high-quality oil shales mainly contain type I kerogen. All are immature to early thermally mature. The oil yield of the oil shales is directly related to their quality and are positively correlated with TOC content and calorific value. All studied samples were deposited under anaerobic conditions but in different paleoenvironments. The low-quality oil shales were mainly deposited in fresh-water environments, whereas the high-quality oil shales were usually developed in highly saline and reducing environments. Salinity stratification and evidence of algal blooms that are conducive to organic matter enrichment were identified in both medium- and high-quality oil shales, the latter having the highest paleoproductivity and the best preservation conditions. In summary, shale quality is controlled by a combination of factors, including algal abundance, preservation conditions, the existence of algal blooms and salinity stratification, and paleoproductivity. This study reveals how these different factors affect the quality of oil shales, which might provide an in-depth explanation for the formation process of lacustrine oil shales.

Flexible temperature sensors have been extensively investigated due to their prospect of wide application in various flexible electronic products. However, most of the current flexible temperature sensors only work well in a narrow temperature range, with their application at high or low temperatures still being a big challenge. This work proposes a flexible thermocouple temperature sensor based on aerogel blanket substrate, the temperature-sensitive layer of which uses the screen-printing technology to prepare indium oxide and indium tin oxide. It has good temperature sensitivity, with the test sensitivity reaching 226.7 μ V °C ^−1 . Most importantly, it can work in a wide temperature range, from extremely low temperatures down to liquid nitrogen temperature to high temperatures up to 1200 °C, which is difficult to be achieved by other existing flexible temperature sensors. This temperature sensor has huge application potential in biomedicine, aerospace and other fields.

The autostereoscopic display is a promising way towards three-dimensional-display technology since it allows humans to perceive stereoscopic images with naked eyes. However, it faces great challenges from low resolution, narrow viewing angle, ghost images, eye strain, and fatigue. Nowadays, the prevalent liquid crystal display (LCD), the organic light-emitting diode (OLED), and the emerging micro light-emitting diode (Micro-LED) offer more powerful tools to tackle these challenges. First, we comprehensively review various implementations of autostereoscopic displays. Second, based on LCD, OLED, and Micro-LED, their pros and cons for the implementation of autostereoscopic displays are compared. Lastly, several novel implementations of autostereoscopic displays with Micro-LED are proposed: a Micro-LED light-stripe backlight with an LCD, a high-resolution Micro-LED display with a micro-lens array or a high-speed scanning barrier/deflector, and a transparent floating display. This work could be a guidance for Micro-LED applications on autostereoscopic displays.

Abstract Background Total P16 methylation (P16M), including P16 hydroxymethylation (P16H) and true-P16M, correlates with malignant transformation of oral epithelial dysplasia (OED). Both true-P16M and P16H are early events in carcinogenesis. The aim of this study is to prospectively determine if discrimination of true-P16M from P16H is necessary for prediction of cancer development from OEDs. Methods Patients (n = 265) with mild or moderate OED were recruited into the double blind two-center cohort. Total-P16M and P16H were analyzed using the 115-bp MethyLight, TET-assisted bisulfite (TAB) methylation-specific PCR (MSP), and TAB-sequencing. Total-P16M-positive and P16H-negative samples were defined as true-P16M-positive. Progression of OEDs was monitored for a minimum 24 months follow-up period. Results P16H was detected in 23 of 73 (31.5%) total-P16M-positive OEDs. Follow-up information was obtained from 247 patients with an ultimate compliance rate of 93.2%. OED-derived squamous cell carcinomas were observed in 13.0% (32/247) patients during follow-up (median, 41.0 months). The cancer progression rate for total-P16M-positive patients was significantly increased when compared to total-P16M-negative patients [23.3% vs 8.6%; adjusted odds ratio = 2.67 (95% CI: 1.19–5.99)]. However, the cancer progression rates were similar between P16H- and true-P16M-positive OEDs [26.1% (6/23) vs 22.0% (11/50); odds ratio = 0.80 (95% CI: 0.22–2.92)]. The cancer-free survival was also similar for these patients. Conclusion P16H and true-P16M are similar biomarkers for determining malignant potential of OEDs. Discrimination of P16H from true-P16M, at least in OED, may be not necessary in clinical applications. Trial registration This study is registered prospectively in the U.S. National Institutes of Health Clinical Trials Protocol Registration System (trial number NCT02967120, available at https://ClinicalTrials.gov/ct2/show/NCT02967120).

In eukaryotes, proteins encoded by the 14-3-3 genes are ubiquitously involved in the plant growth and development. The 14-3-3 gene family has been identified in several plants. In the present study, we identified 22 GmGF14 genes in the soybean genomic data. On the basis of the evolutionary analysis, they were clustered into ε and non-ε groups. The GmGF14s of two groups were highly conserved in motifs and gene structures. RNA-seq analysis suggested that GmGF14 genes were the major regulator of soybean morphogenesis. Moreover, the expression level of most GmGF14s changed obviously in multiple stress responses (drought, salt and cold), suggesting that they have the abilities of responding to multiple stresses. Taken together, this study shows that soybean 14-3-3s participate in plant growth and can response to various environmental stresses. These results provide important information for further understanding of the functions of 14-3-3 genes in soybean.

The ocean connects all continents and is an important space for human activities. Ship detection with electro-optical images has shown great potential due to the abundant imaging spectrum and, hence, strongly supports human activities in the ocean. A suitable imaging spectrum can obtain effective images in complex marine environments, which is the premise of ship detection. This paper provides an overview of ship detection methods with electro-optical images in marine environments. Ship detection methods with sea–sky backgrounds include traditional and deep learning methods. Traditional ship detection methods comprise the following steps: preprocessing, sea–sky line (SSL) detection, region of interest (ROI) extraction, and identification. The use of deep learning is promising in ship detection; however, it requires a large amount of labeled data to build a robust model, and its targeted optimization for ship detection in marine environments is not sufficient.

In recent years, ambient contrast ratio (ACR) has become very critical for advanced outdoor displays, including transparent displays, portable displays, and so on. In this work, the ACR of typical flat panel displays was introduced, while LED-based displays showed distinctive advantages. Micro-LED displays with a different pitch of 10 μm, 15 μm, 30 μm, and 60 μm were fabricated and characterized. Various mini-LED and micro-LED panels were systematically investigated in the aspect of brightness, reflection phenomenon, and ACR to reveal their enormous potential for outdoor applications. Through a series of experiments and comparisons, three methods were proposed to further improve the ACR of LED-based panels, including optical method, antireflection coating, and structure optimization.

Background/Aims: Previous studies have suggested that autophagy is activated in distinct cerebrovascular diseases, including stroke. However, the underlying regulatory mechanism of autophagy under stroke remained elusive. Accumulating evidence indicates that dysfunctions of microRNAs (miRNAs) are involved in the pathological process of stroke. Therefore, this study was taken to identify the effect of microRNA-9a-5p (miR-9a-5p) on autophagy in rats following stroke. Methods: The rat model of focal cerebral ischemia was established by middle cerebral artery occlusion (MCAO) surgery; The neurological outcomes were defined by neurological evaluation and infarct volume; The western blotting and immunofluorescence assays were used to detected the protein levels of microtubule-associated protein 1 light chain 3 (LC3) and autophagy related 5 (ATG5); The mRNA level of miR-9a-5p, LC3 and ATG5 were quantified by real-time RT-PCR; The luciferase activities of ATG5 and miR-9a-5p was detected by luciferase assay. Results: We showed here that the level of miR-9a-5p was decreased in the ischemic region of rats after MCAO. Overexpression of miR-9a-5p by miR-9a-5p agomir reduced infarct volume and alleviated neurological deficit. Moreover, we found that autophagy was activated by miR-9a-5p inhibition and inactivated by miR-9a-5p overexpression both in the MCAO rat and in SY-5Y cell lines, and unchanged by miR-masks as indicated by LC3 expression. Furthermore, the protein level of ATG5 was decreased by miR-9a-5p overexpression, but increased by miR-9a-5p inhibition and unchanged by miR-masks transfection. In addition, the luciferase assay data showed that miR-9a-5p suppressed the luciferase activity of 3’UTR of ATG5, whereas the repressive effect was relieved by mutation of binding sites. Conclusion: Our study demonstrated that miR-9a-5p may play a critical role in regulating the process of autophagy through targeting ATG5 expression, and overexpression of miR-9a-5p may be a potential approach in alleviating ischemia injury induced by MCAO.

The synchronous variation and association of organic matter (OM) and minerals in the hydrocarbon-generated process of oil shales are poorly understood. The goal of the paper is to investigate OM occurrence and thermal variation so as to reveal the hydrocarbon generation potential of oil shales. Based on detailed analyses of particle, organic, mineral, and thermal data from lacustrine oil shales in the Songliao Basin, we observed three layers of shale particles after settling in the water column characterized by a distinct color, degree of consolidation, and particle size. The particle sizes are divided into three ranges of fine grain (20 μm) via laser particle analysis. The particle-size distribution indicates the presence of OM polymerization and dominant contribution of the associated mineral surface and bioclastic OMs to the OM abundance of oil shale. Various OM occurrences are influenced by OM sources and redox conditions, whereas the degree of biodecomposition and particle sizes affect the placement of OM occurrences. Based on multiple thermal analyses, a synchronous response of OM and minerals to thermal variation dominates at 300–550 °C. The I/S and chlorite minerals are characterized by an entire illitization, while solid/absorbed OMs and hydrocarbon-generated water were expelled in large quantities. This contributes to major loss weights of oil shales during heating. The peak hydrocarbon-generated rate occurred at 457 °C for oil shales, corresponding to around 1.3% vitrinite reflectance value. These results are suggested to improve the understanding of OM occurrences and the thermal degradation constraint on the hydrocarbon-generated process, and contribute to the interpretation of the hydrocarbon generation potential and in-situ exploitation of oil shales.

Salmonella enterica serovar Enteritidis (S. Enteritidis) is a pathogen that poses a health risk. Blue light (BL), an emerging sanitization technology, was employed for the first time in the present study to inactivate S. Enteritidis on eggshell surfaces and its influence on maintaining eggshell freshness was investigated systematically. The results showed that 415 nm-BL irradiation at a dose of 360 J/cm2 reduced 5.19 log CFU/mL of S. Enteritidis in vitro. The test on eggshells inoculated with S. Enteritidis showed that a BL dose at 54.6 J/cm2 caused a 3.73 log CFU reduction per eggshell surface and the impact of BL inactivation could be sustained in post-5-week storage. The quality of the tested eggs (weight loss, yolk index, Haugh unit (HU) and albumen pH) demonstrated that BL treatments had negligible effects on the albumen pH of eggs. However, compared to the control, BL-treated eggs showed lower weight loss and higher HU after 5 weeks of storage at 25 °C and 65% humidity and yolk index in the control group could not be determined after 5 weeks of storage. Besides, the total amino acid content of the BL-treated egg was higher than the control, exhibiting an advantage of BL irradiation in maintaining the nutrient quality of whole eggs. The current study determined the efficacy of BL against S. Enteritidis on eggshell and suggested that BL could be an effective application in maintaining the freshness and quality of eggs.

In the present study, a high-performance n-type temperature sensor was developed by a new and facile synthesis approach, which could apply to ambient temperature applications. As impacted by the low sintering temperature of flexible polyimide substrates, a screen printing technology-based method to prepare thermoelectric materials and a low-temperature heat treatment process applying to polymer substrates were proposed and achieved. By regulating the preparation parameters of the high-performance n-type indium oxide material, the optimal proportioning method and the post-treatment process method were developed. The sensors based on thermoelectric effects exhibited a sensitivity of 162.5 μV/°C, as well as a wide range of temperature measurement from ambient temperature to 223.6 °C. Furthermore, it is expected to conduct temperature monitoring in different scenarios through a sensor prepared in masks and mechanical hands, laying a foundation for the large-scale manufacturing and widespread application of flexible electronic skin and devices.

In some cases, the oil shale deposited in shallow lakes may be genetically associated with the coal-bearing successions. Although paleovegetation is an important controlling factor for the formation of oil shale- and coal-bearing successions, few studies have focused on their joint characterization. In this study, a total of twenty-one oil shale and coal samples were collected from the upper member of the Lower Cretaceous Muling Formation (K1ml2) in the Laoheishan Basin, and investigated for their bulk geochemical, maceral, palynological, and terpenoid biomarker characteristics, in order to reconstruct the paleovegetation and reveal its influence on the formation of oil shale and coal. The K1ml2 is subdivided into lower, middle, and upper units. The studied oil shale samples from the lower and upper units display a high ash yield (Ad), low total organic carbon (TOC) and sulfur (S) contents, and limited hydrocarbon generation potential. The studied coal samples from the middle unit are characterized by low Ad, and high TOC and low S values, and show significant hydrocarbon generation potential. The paleovegetation during the formation of the lower unit was dominated by mire vegetation, such as shrubs (e.g., Lygodiaceae, Schizaeaceae), tree ferns (e.g., Dicksoniaceae/Cyatheaceae), and coniferous trees (e.g., Podocarpaceae). In the middle unit interval, the paleovegetation was represented by highland vegetation (Pinaceae and Araucariaceae) and peat-forming coniferous plants (e.g., Podocarpaceae, Cupressaceae/Taxodiaceae). Various vegetation, such as herbs (e.g., Osmundaceae), shrubs (e.g., Schizaeaceae), and coniferous trees (e.g., Podocarpaceae) was prosperous during the upper unit interval. Coniferous trees could provide abundant hydrogen-rich materials (e.g., resins) to the mire/lake, which may elevate the hydrogen content in peat/lake sediments, and finally result in higher hydrocarbon generation potential in the coal than in the oil shale. Therefore, the influence of paleovegetation on the formation of oil shale and coal should be fully considered when studying oil shale- and coal-bearing successions. The results also provide guidance for further exploration studies on oil shale and coal in northeast China.

Data-driven chatter detection techniques avoid complex physical modeling and provide the basis for industrial applications of cutting process monitoring. Among them, feature extraction is the key step of chatter detection, which can compensate for the accuracy disadvantage of machine learning algorithms to some extent if the extracted features are highly correlated with the milling condition. However, the classification accuracy of the current feature extraction methods is not satisfactory, and a combination of multiple features is required to identify the chatter. This limits the development of unsupervised machine learning algorithms for chattering detection, which further affects the application in practical processing. In this paper, the fractal feature of the signal is extracted by structure function method (SFM) for the first time, which solves the problem that the features are easily affected by process parameters. Milling chatter is identified based on k-means algorithm, which avoids the complex process of training model, and the judgment method of milling chatter is also discussed. The proposed method can achieve 94.4% identification accuracy by using only one single signal feature, which is better than other feature extraction methods, and even better than some supervised machine learning algorithms. Moreover, experiments show that chatter will affect the distribution of cutting bending moment, and it is not reliable to monitor tool wear through the polar plot of the bending moment. This provides a theoretical basis for the application of unsupervised machine learning algorithms in chatter detection.

Abstract Background Acute pancreatitis (AP) is a life-threatening disease that requires early identification of patients at risk of developing infectious complications. Immunosuppression is an initial event that is key to AP pathogenesis. The programmed cell death 1 (PD-1) and programmed cell death ligand 1 (PD-L1) system is reported to mediate evasion of host immune surveillance in many diseases; however, the relationship between PD-1/PD-L1 expression and these parameters or infectious complications in AP has not been elucidated. This study was conducted to determine whether PD-1 and PD-L1 are upregulated and to reveal the relationship between PD-1/PD-L1 expression and the development of infectious complications in AP. Methods Sixty-three patients with AP and 32 sex- and age-matched healthy control subjects were prospectively enrolled. On days 1 and 3 after the onset of AP, we measured PD-1 expression in peripheral CD4+ T cells and PD-L1 and human leukocyte antigen-DR (HLA-DR) expression in CD14+ monocytes using flow cytometry. Plasma interleukin (IL)-10 levels were measured by enzyme-linked immunosorbent assay. Results Compared with healthy volunteers, the percentages of PD-1-expressing CD4+ lymphocytes and PD-L1-expressing CD14+ monocytes were increased in patients with AP on days 1 and 3 after onset, especially those with infectious complications. Moreover, increased PD-1/PD-L1 expression was associated with increased occurrence of infectious complications, decreased circulating lymphocytes, and increased plasma IL-10 concentration. Multivariate regression analysis indicated that the increased percentage of PD-L1-expressing CD14+ monocytes was an independent risk factor for infectious complications in AP. Area under the ROC curve analysis showed the combination of Acute Physiology and Chronic Health Evaluation II score and PD-L1 and HLA-DR expression in CD14+ monocytes had high accuracy in predicting infectious complications in patients with AP. Conclusions The PD-1/PD-L1 system plays an essential role in the early immunosuppression of AP. PD-L1 expression in CD14+ monocytes may be a new marker for predicting risk of infectious complications in patients with AP.

In this paper, we report the design and fabrication of fine-pitch and pixelated-addressed micro-light emitting diode (LED) arrays with emission wavelengths of red (R), green (G), blue (B), and infrared (IR). The arrays have a resolution of 8×8 with monochromatic LED chips directly bonded to custom-designed printed circuit boards to form pixelated matrix. R, G, B, and IR micro-LED arrays with a pixel pitch of 1 mm were demonstrated. Sequential row scanning and multiple columns programming is performed by two CMOS-based application specific integrated circuit chips providing constant-sinking current and forward voltage for each pixel of the micro-LED arrays. The uniformity of operating current and forward voltage of the micro-LED pixels was measured with 1.94% coefficient of variation. The micro-LED pixel has much shorter rising time and higher response frequency than those of regular packaged blue and white LEDs. The implemented R-G-B micro-LED arrays are the excellent candidate for high-definition fine-pitch LED displays and demonstrated its versatile functionalities such as visible light communications. The IR micro-LED arrays show great potential in health medical treatment, IR detection imaging and local positioning system.

Background VQ proteins, the plant-specific transcription factors, are involved in plant development and multiple stresses; however, only few articles systematic reported the VQ genes in soybean. Methods In total, we identified 75 GmVQ genes, which were classified into 7 groups (I-VII). Conserved domain analysis indicated that VQ gene family members all contain the VQ domains. VQ genes from the same evolutionary branches of soybean shared similar motifs and structures. Promoter analysis revealed that cis-elements related to stress responses, phytohormone responses and controlling physical as well as reproductive growth. Based on the RNA-seq and qRT-PCR analysis, GmVQ genes were showed expressing in nine tissues, suggesting their putative function in many aspects of plant growth and development as well as response to stress in Glycine max. Results This study aims to understand the roles of VQ genes in various development processes and their expression patterns in responses to stimuli. Our results provide basic information in identification and classification of GmVQ genes. Further experimental analysis will allows us to know the functions of GmVQs participation in plant growth and stress responses.

Myasthenia gravis (MG) is an autoimmune disease. In recent years, considerable evidence has indicated that Gene Ontology (GO) functions, especially GO-biological processes, have important effects on the mechanisms and treatments of different diseases. However, the roles of GO functions in the pathogenesis and treatment of MG have not been well studied. This study aimed to uncover the potential important roles of risk-related GO functions and to screen significant candidate drugs related to GO functions for MG. Based on MG risk genes, 238 risk GO functions and 42 drugs were identified. Through constructing a GO function network, we discovered that positive regulation of NF-kappaB transcription factor activity (GO:0051092) may be one of the most important GO functions in the mechanism of MG. Furthermore, we built a drug-GO function network to help evaluate the latent relationship between drugs and GO functions. According to the drug-GO function network, 5 candidate drugs showing promise for treating MG were identified. Indeed, 2 out of 5 candidate drugs have been investigated to treat MG. Through functional enrichment analysis, we found that the mechanisms between 5 candidate drugs and associated GO functions may involve two vital pathways, specifically hsa05332 (graft-versus-host disease) and hsa04940 (type I diabetes mellitus). More interestingly, most of the processes in these two pathways were consistent. Our study will not only reveal a new perspective on the mechanisms and novel treatment strategies of MG, but also will provide strong support for research on GO functions.

The present study aimed to examine whether a self-related stimulus produces a self-related process bias between pathological-tendency Internet users and ordinary Internet users. Participants were asked to judge the color of the target stimulus’ frame (Internet pictures) in an implicit priming task, which enclosed the prime of self/other related words and the target of the online image in sequence. Results from Experiment 1 showed that response time (RT) in the self-related condition was significantly longer than that of the other related condition. Further analysis showed that RT in the self-related condition was significantly longer than that under the other related conditions for pathological-tendency Internet users but not for ordinary Internet users. In Experiment 2, behavior results demonstrated that RT under the self-related condition was significantly longer than that in the other-related condition for both groups, and the RT was shorter for pathological-tendency Internet users than that of the ordinary Internet users. Moreover, ERP data showed that the N2 amplitude was larger in the self-related condition than that of other related conditions for pathological-tendency Internet users but not for ordinary Internet users. The amplitudes of late positive component (LPC) was smaller in the self-related condition than those of the other related conditions. Hence, the Internet use influenced the inhibition control in self-unrelated stimuli and automatically retrieved the self-related stimuli.

A single-longitudinal-mode (SLM) Neodymiun-doped Yttrium Aluminium Garnet (Nd:YAG) laser at 1123 nm was first demonstrated with a twisted-mode (TM) cavity. By eliminating the spatial hole burning phenomenon, a stable SLM 1123 nm laser output was obtained. An efficient TM cavity was designed based on the Brewster plate with high reflection under s-polarization radiation. At an incident pump power of 7.65 W, the maximum output power of 689 mW was obtained. The corresponding optical conversion efficiency was about 9%. The center wavelength was 1122.58 nm and the line-width was

The characteristics of a tunable Stokes laser based on the cascaded stimulated polariton scattering and stimulated Raman scattering in KTiOPO4 crystal were studied experimentally and theoretically. When the pumping wavelength was 1064 nm, the Stokes laser output wavelength was able to be tuned discontinuously from 1112.08 nm to 1113.64 nm, from 1114.94 nm to 1115.77 nm, and from 1117.37 nm to 1119.92 nm, and the maximum output power appeared at 1118.86 nm. With a pulse repetition frequency of 7 kHz and a pump power of 6.0 W, the maximum output power of the Stokes laser reached 734 mW, and the corresponding diode to laser conversion efficiency was 12.2%. The rate equations describing the temporal evolutions of the fundamental and Stokes waves by noncollinear stimulated polariton scattering and the Stokes wave by collinear stimulated Raman scattering were derived. They were used to simulate the tunable Stokes laser. The calculated results were in agreement with the experimental results on the whole.

Common methods of ocean remote sensing and seafloor surveying are mainly carried out by airborne and spaceborne hyperspectral imagers. However, the water column hinders the propagation of sunlight to deeper areas, thus limiting the scope of observation. As an emerging technology, underwater hyperspectral imaging (UHI) is an extension of hyperspectral imaging technology in air conditions, and is undergoing rapid development for applications in shallow and deep-sea environments. It is a close-range, high-resolution approach for detecting and mapping the seafloor. In this paper, we focus on the concepts of UHI technology, covering imaging systems and the correction methods of eliminating the water column’s influence. The current applications of UHI, such as deep-sea mineral exploration, benthic habitat mapping, and underwater archaeology, are highlighted to show the potential of this technology. This review can provide an introduction and overview for those working in the field and offer a reference for those searching for literature on UHI technology.

High detection efficiency appears to be associated with a high afterpulse probability for InP-based single-photon avalanche diodes. In this paper, we present a new hybrid quenching technique that combines the advantages of both fast active quenching and high-frequency gated-passive quenching, with the aim of suppressing higher-order afterpulsing effects. Our results showed that the hybrid quenching method contributed to a 10% to 85% reduction of afterpulses with a gate-free detection efficiency of 4% to 10% at 1.06 μm, with 40 ns dead time, compared with the counter-based hold-off method. With the improvement of the afterpulsing performance of high-frequency gated single-photon detectors, especially at relatively high average detection efficiencies with wide gate widths, the proposed method enables their use as high-performance free-running detectors.

This paper reports the characteristics of an injection-seeded terahertz parametric oscillator (TPO) with a ring-cavity configuration based on the MgO:LiNbO3 crystal. The ring cavity is constituted of three mirrors and the THz wave output surface where the pump and Stokes beams are totally reflected. The THz pulse energies and the Stokes pulse energies as functions of the pump pulse energy for different seed powers of 47.5 mW, 150.7 mW, and 312.8 mW were investigated. The experimental results showed that the injection-seeded ring cavity TPO exhibited the benefits of lower pump thresholds and higher output energies for the Stokes and THz waves. The smaller the pump pulse energy, the more obvious the effect of the seed injection. The reasons for the laser performance improvement were analyzed.

WRe26-In2O3 (WRe26 (tungsten-26% rhenium) and In2O3 thermoelectric materials) thin film thermocouples (TFTCs) have been fabricated based on magnetron sputtering technology, which can be used in temperature measurement. Many annealing processes were studied to promote the sensitivity of WRe26-In2O3 TFTCs. The optimal annealing process of the thermocouple under this kind of RF magnetron sputtering method was proposed after analyzing the properties of In2O3 films and the thermoelectric voltage of TFTCs at different annealing processes. The calibration results showed that the WRe26-In2O3 TFTCs achieved a thermoelectric voltage of 123.6 mV at a temperature difference of 612.9 K, with a sensitivity of up to 201.6 µV/K. Also, TFTC kept a stable thermoelectric voltage output at 973 K for 20 min and at 773 K for two hours. In general, the WRe26-In2O3 TFTCs developed in this work have great potential for practical applications. In future work, we will focus on the thermoelectric stability of TFTCs at higher temperatures.

In terms of their use in displays, quantum dots (QDs) exhibit several advantages, including high illumination efficiency and color rendering, low-cost, and capacity for mass production. Furthermore, they are environmentally friendly. Excellent luminescence and charge transport properties of QDs led to their application in QD-based light-emitting diodes (LEDs), which have attracted considerable attention in display and solid-state lighting applications. In this review, we discuss the applications of QDs which are used on color conversion filter that exhibit high efficiency in white LEDs, full-color micro-LED devices, and liquid-type structure devices, among others. Furthermore, we discuss different QD printing processes and coating methods to achieve the full-color micro-LED. With the rise in popularity of wearable and see-through red, green, and blue (RGB) full-color displays, the flexible substrate is considered as a good potential candidate. The anisotropic conductive film method provides a small controllable linewidth of electrically conductive particles. Finally, we discuss the advanced application for flexible full-color and highly efficient QD micro-LEDs. The general conclusion of this study also involves the demand for a more straightforward QD deposition technique, whose breakthrough is expected.

The Songliao Basin contains some of the largest volumes of oil shales in China; however, these energy sources are located in areas covered by arable land, meaning that the best way of exploiting them is likely to be environmentally friendly in situ conversion processing (ICP). Whether the oil shales of the Songliao Basin in the Qingshankou Formation are suitable for ICP remain controversial. In this paper, through sequence stratigraphic correlations, three main thick oil shale layers (N1, N2, and N3) of the Sequence1 (Sq1) unit in the first member of Qingshankou Formation (K2qn1) are confirmed as consistently present throughout the Southeastern Uplift region of the basin. The spectral trend attributes reflect that the lake reached a maximum flood surface of the K2qn1 in N2 oil shale layer, and the total organic carbon (TOC) and Fischer assay (FA) oil yield are significantly increasing. The N2 and N3 oil shale layers were deposited in a high lake level environment associated with ingressions of ocean water. The oil shale in these layers with the characteristics of high TOC (maximum of 23.9 wt %; average of 7.2 wt %), abundance of aquatic organic matter (OM) (maximum hydrogen index (HI) of 1080.2 mg/g; average of 889.9 mg/g) and carbonate contents (maximum of 29.5%; average of 15.4%). The N2 and N3 oil shale layers have higher brittleness index (BI) values (generally 40–50%), larger cumulative thicknesses (maximum of 13.3 m; average of 12.0 m), and much higher source potential index (SPI) values (0.92 and 0.88 tHC/m2, respectively) than the N1 oil shale layer within Sq1 transgressive system tracts (TST), indicating that the N2 and N3 layers are prospective targets for ICP. In addition, oil shales buried to depths of

In this paper, we report high-performance Micro-LEDs on sapphire substrates, with pixel size scaling to 20 µm and an ultra-high current density of 9902 A/cm2. The forward voltages (VF) of the devices ranged from 2.32 V to 2.39 V under an injection current density of 10 A/cm2. The size and structure-dependent effects were subsequently investigated to optimize the device design. The reliability of Micro-LED devices was evaluated under long-aging, high-temperature, and high-humidity conditions. It was found that Micro-LED devices can maintain comparable performance with an emission wavelength of about 445 nm and a full width at half maximum (FWHM) of 22 nm under extreme environments. Following this, specific analysis with four detailed factors of forward voltage, forward current, slope, and leakage current was carried out in order to show the influence of the different environments on different aspects of the devices.

Optical projection tomography (OPT) is the direct optical equivalent of X-ray computed tomography (CT). To obtain a larger depth of field, traditional OPT usually decreases the numerical aperture (NA) of the objective lens to decrease the resolution of the image. So, there is a trade-off between sample size and resolution. Commercial microfluidic systems can observe a sample in flow mode. In this paper, an OPT instrument is constructed to observe samples. The OPT instrument is combined with commercial microfluidic systems to obtain a three-dimensional and time (3D + T)/four-dimensional (4D) video of the sample. “Focal plane scanning” is also used to increase the images’ depth of field. A series of two-dimensional (2D) images in different focal planes was observed and compared with images simulated using our program. Our work dynamically monitors 3D OPT images. Commercial microfluidic systems simulate blood flow, which has potential application in blood monitoring and intelligent drug delivery platforms. We design an OPT adaptor to perform OPT on a commercial wide-field inverted microscope (Olympusix81). Images in different focal planes are observed and analyzed. Using a commercial microfluidic system, a video is also acquired to record motion pictures of samples at different flow rates. To our knowledge, this is the first time an OPT setup has been combined with a microfluidic system.